A0620175 Meteor-175W Underwater Pool Light Operating Instructions
Contents
1. dim controller 230V AC LED 12 24V Power Supply CONTROLS Remote control can be used to turn on and turn off the underwater pool light and to control the luminosity Remote control connection To remotely turn on and turn off the underwater pool light the simple switch not included can be used and connected to the CONTROL wires by a 2 pole signal cable not included Note If the remote control is not used at single color models for normal operation the both CONTROL wires have to be bridged and insulated or connected to the GND Turning on off Press the key switch momentary Dimming When the light is turned on press the key switch until the desired illumination is achieved By another pressing of the key switch the luminosity will increase to the maximum illumination Set default Press the key switch for min 40 seconds or until the light is turned off TECHNICAL SPECIFICATIONS Power supply 24 Vdc max 3 4A 24 Vdc Lens angle 60 Optical window High grade polycarbonate glass Luminous flux max 7000 Lm Operating temperature 10 C 40 C Casing Stainless steel 316L Protection IP68 Dimensions 176x17mm Weight 2 3 kg Highlite international BV Vestastraat 2 NL 6468 EX Kerkrade The Netherlands ARTECTA Division Phone 31 0 45 5667734 Fax 31 0 45 5667709 Design and specifications subject to change without notice E Mail artecta highlite nl2. ie LED technology ART A0620175 Meteor 175W Underwater Pool Light Operating Instructions CONTENTS PROTA CC A 85 cia di dine czetg AE EAE A E EEEE ERBE EEEEESTEUERE BELFENELENIRIEEERSECHENEELERTBER REES 3 Features ooie reia a a sa aa iaeaea EES eE RAEE E Ee ADES ea ea EEE a BRESERSPRBEFRGISERGENSEESPRARENE 3 SAKETE UiO 1N E ee EE E ee ET 3 Components and Conneclors ran ende eher ea ea a a ae naeh 4 Installation 2 as en nenn EENE aN 5 amp fo n 1 0 e vst oo es see 2h cd stereo iin Pe cated aaa helene E ances RE Gs eae va aso etn vedo bed ated cheddar REE ae 7 AAD PEGI ANCES E E E A E E EES EETA E E EE E E E E E E 8 Technical Specifications sirr eaa neuen E EE EEEN 8 PREFACE The METEOR 175W compact ultra thin underwater pool light with built in driver is designed to use the latest LED lighting technology The surface mount designed casing enable very simple installation on the flat surface without any surface preparation during construction and the max diameter of the hole through the wall is 8 mm The METEOR 175W is available in stainless steel casings with 36 warm white highpower LEDs The most advanced electronic design with built in microprocessor enables network connection and simple control of complete group of lights with dimming PRECAUTIONS e The underwater pool light has to be installed and used in accordance with the instructions of this manual only e The power supply has to be disconnected before instal
3. lation e The underwater pool light is recomended to be installed around 0 2 m below the water line for the best illumination and to avoid over heating e The optical window must be clear and not covered by any kind of isolating or other material The optical window has to be cleaned with a mild soap or detergent and lukewarm water by using a soft cloth or sponge Do not use abrasive or highly alkaline cleaners e Never scrape with razor blades or other sharp instruments Benzene leaded gasoline acetone or carbon tetrachloride should never be used e Do turn power off immediately and refer servicing to qualified service personnel if the underwater pool light does not operate normally following the operating instructions FEATURES APPEARANCE Innovative DesignS Stainless Steel Ultra Thin Casing 36 Power LEDs Design Warm white Lighting High Grade Polycarbonate Glass Optical Window Vacuum Metalized Reflector Remote Control Digital Dimming Polarity Protection Transient Protection Thermal Protection Wide Range Power Supply Low Power Consumption Simple Installation Optional accessories for different pools installations 5m 4 Pole Multicable pog Powersupply DC Black Powersupply DC Orange Pulse Control Brown Pulse Control GND Stainless Steel 316L stainless steel 316L Fixing Screws ae High grade polycarbonate glass optical window 1 Optical window High grade polycarbonate glass optical windo
4. r cable gland drilled through the wall has to be 8 mm Sealing Before inserting the cable with gland through the hole the sealant has to be used into the grooves around the four fixing holes and around the gland in the rear surface of the underwater pool light The sealant can be on silicon basis but the best solution is two component polymer sealant Fixing The underwater light has to be fixed with four screws 5 5x38 with wallplugs Note Do not overtighten the screws as this can result in underwater pool light damage Earthing The underwater pool light has to be earthed by using a pre tinned green wire with a yellow stripe a minimum of 8 AWG 8 36 mm2 The wire has to be connected to the underwater pool light by the help of one fixing screw 5 5x38 Connection The power supply has to be connected through the main switch not included with correct polarity and protected by a fuse not included The power supply voltage has to be from 10 30Vdc Note e The power supply has to be switched off before installation The underwater light has to be connected as described in the table below METEOR 120W FUNCTION wire color Red DC Power Supply Black GND Power Supply Orange Control Brown GND Control Remote control connection To control the mode of lighting the simple key switch not included has to be used and connected to the CONTROL wires by the 2 pole signal cable not included Puls
5. w 2 Underwater pool light casing Stainless steel casing with fixing holes and cable gland 3 Cable The 4 pole multi core cable to connect the 12 24Vdc power supply and optional remote control or switch 4 Fixing screw The fixing screws to fix the underwater pool light on the wall INSTALLATION The underwater light kit consists of the following components e Underwater Light METEOR 175W e 4 x fixing screw 5 5x38 with wallplugs e Operating Instructions The METEOR 120 has to be installed on a flat surface on the pool wall under water line Do not try to install the underwater pool light while the pool is filled with water When the installation is finished briefly test the underwater light prior to fill the pool with water The installation have to be realized by a qualified personnel Sealing A Wall Sealing Grooves 2X Note Avoid using the underwater pool light out of the water for more than 2 minutes The underwater pool light is protected by a temperature sensor against over heating When the temperature of the underwater pool light exceeds 85 C the underwater pool light is automatically switched off Wall preparation The underwater pool light is recommended to be installed around 0 2 m below the waterline for the best illumination and to avoid over heating To fix the underwater pool light with screws 5 5x38 the diameter of holes drilled into the wall has to be 8 mm The diameter of the hole fo
Download Pdf Manuals
Related Search