PB-PWD9600 Installation Manual
Contents
1. PB PWD9600 Installation Manual Issued 04 11 2008 Polar Bear Solutions reserves the right to alter specifications without notice at any time For full warranty information refer to the Instruction Manual s associated with your Product s Polar Bear PB PWD9600 Installation Manual Tiet Rr Polar Bear Solutions Limited Warranty and Disclaimer Polar Bear Solutions warrants its products to be free of defects in material and workmanship under normal use for one 1 year from the date of purchase from Polar Bear Solutions with the following exceptions e Unless otherwise specified OEM and custom products are warranted for a period of one 1 year e Any products in which the serial number has been removed defaced or modified e Where any defect or failure is attributed to accident misuse abuse negligence or non observance of the product user guide on the part of the installer owner or user e Damage or defects caused by abnormal or unreasonable use including unauthorised system modifications repairs and specifically alterations by a person or party other than Polar Bear Solutions or their authorised agents e Damage or defects resulting from acts of nature such as lightning strikes or floods e POLAR BEAR SOLUTIONS Software is warranted for a period of ninety 90 days This warranty extends only to products purchased directly from POLAR BEAR SOLUTIONS or an Authorised POLAR BEAR SOLUTIONS Dealer within their autho2. same link number Homeworks Illumination Lutron Intergrated Example HDF Programming SEE Ele View Reports Help DAR SQ ApH Trea Control Station Programming Lighting jazi Shades X Fans Keypads E Interfaces Global Add Update lt gt Selectan Fite falRooms S Switched Zones a Ground Floor Cupboard Panel Anw COST E El DimmedZones Family Room Feature Spot 1 1 0 1 1 Show Closure Board Butor fio Family Room Front Downlights 1 1 0 1 2 Family Room Rear Downlights 1 1 0 1 4 Family Room Table Lamps 1 1 0 2 1 Family Room Wall Lights 1 1 0 2 2 Kitchen Cooker Hood 1 1 0 2 3 Mii Kitchen Cupboards 1 1 0 2 4 Kitchen Pendant 1 1 0 3 2 Kitchen Side Uplights 1 1 0 3 3 Kitchen Wall Lights 1 1 0 3 4 Kitchen worktop Downlights 1 1 0 4 1 E 8 Switched Zones Family Room Low Level LED 1 1 0 1 3 ga Kitchen Low Level LEDs 1 1 0 3 1 GRAFIK Eye Main Units Close Properties Notes Remove froperies Defaut gt RealTime Equipment r e n Family Room Feature Spot 00 00 00 02 90 ___ Famity Room Front Downlights 00 00 00 02 20 00 00 __ Family Room Rear Downlights 00 00 00 02 Equipment Link Link 5 Hw Keypad __ Family Room Table Lamps 00 00 00 02 Family Room Wall Lights 00 00 00 02 _ Kitchen Low Level LEDs 00 00 00 00 Show Advanced Properties m i 8 o e b e lo Button Blanking Strip Included with the product
3. two holes just above the shelf see fig2 Securing Screws Polar Bear Solutions reserves the right to alter specifications without notice at any time For full warranty information refer to the Instruction Manual s associated with your Product s Polar Bear PB PWD9600 Installation Manual sigan Rr Power Supply A 12v DC power supply should be used to power the wall dock and in turn charge the TSU9600 when docked When installing cabling within a building it is essential that the correct size cable is used and Suitably protected by either a fuse or other appropriate means in accordance with relevant low voltage guidelines for your country The DC power at the entry point into the product should be between 9v amp 12v lower voltage is actually better If a Philips TSU9600 is suspected to have a faulty battery or problem do not dock the touch screen panel in the wall dock Failure to meet these specifications may cause permanent damage to the wall dock product RJ 45 Dry Contact connector The RJ45 socket on the back box PCB is used for the dry contact closure cabling RJ45 Socket T568B Left to Right Button 1 Brown White Pin7 amp Brown Pin8 Button 2 Blue White Pin5 amp Blue Pin4 Button 3 Green White Pin3 amp Green Pin6 Button 4 Orange White Pin1 amp Orange Pin2 Button Usage Example Integrating two Polar Bear Wall Docks PWD 9600 with a Lutron Lighting system Homeworks Th
4. e four buttons can be used to control a whole house lighting control system This can be achieved by directly wiring the CAT5e cable to an Input board For Homeworks using a HW CCI Board The input board is then programmed using the lighting control system as if it was a Keypad Wiring Diagram Interaratit t Polar Bear Wall kK P WD Pope Lutron Orr rk HW RJA T E Homework Board Brown amp White w m o Button E A A Blue amp White i Ta z Button 2 a a DIUS All LN MON C n hi Ta S AA O Button 3 a Vl 2 Orange amp White ee Button 4 Oroande r S Ite T Jl yttor By A Blue _ amp White tee me Itton 2 TO pa O Ue all Ci eer White E Ej E Button Va an White _ Button 4 ani I C 7 Polar Bear Solutions reserves the right to alter specifications without notice at any time For full warranty information refer to the Instruction Manual s associated with your Product s Polar Bear PB PWD9600 Installation Manual Polar Bea Programming a Lutron CCI board The programming of a Lutron CCI board is done in the same way as a typical keypad The CCI unit can co exist with other Lutron Keypads on the
5. however will not apply to claims for personal injury Under no circumstances shall Polar Bear Solutions be liable by virtue of this warranty or otherwise for any special indirect secondary or consequential damages of any nature arising out of any use or inability to use the home entertainment communications system EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY POLAR BEAR SOLUTIONS MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE POLAR BEAR SOLUTIONS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY A HOT SURFACES WARNI NG During operation the back box and the PCB board can get hot Sufficient care should be taken when handling or removing the product after operation It is recommended that an appropriate amount of time is left after the unit powered off to allow the PCB and back box to cool down Lower input voltages decrease the heat of the unit INSTALLATION COMPETENCE This product is not intended to be installed by the general public or other un trained personnel The product should only be installed by trained individuals that have a minimum level of CEDIA qualification or other equivalent qualifications within the custom audio visual installation industry Installation that is not carried out correctly may invalidate the
6. is a button blanking strip that can be used to hide the four contact buttons on the product if not in use Before the product is located in the wall remove the two screws see fig3 this releases the button bezel and the four plastic buttons The blanking strip can then replace the button bezel and is attached with the two same screws Polar Bear Solutions reserves the right to alter specifications without notice at any time For full warranty information refer to the Instruction Manual s associated with your Product s PB PWD9600 Installation Manual a i Tech Specification Power input requirement 12v DC 1 8Amps max 12v DC min 9v DC Push Buttons 4 x Momentary Volt Free Contacts Max Current rating 50mA 12Vdc Power terminal size 2x 2 5mm screw terminal Colour Silver Back Box Size 180 x 142 x 89mm W x H x D Product size on wall 187 x 150 W x H Contact Polar Bear Solutions Ltd Web site http www PolarBearSolutions com Email sales polarbearsolutions com Polar Bear Solutions reserves the right to alter specifications without notice at any time For full warranty information refer to the Instruction Manual s associated with your Product s
7. llow the cables to be terminated and tested prior to the final stage of the project The back box will get hot during the charging process and therefore should not be placed next to objects that will be affected by this Back Box I nstallation The back box should be installed into a wall securely using the fixing holes The front of the back box should sit flush with the finished wall otherwise longer M4 securing screws may be required to attached the wall dock If the back box is to be left installed without the wall dock the back box PCB board should be adequately protected This PCB board should not be removed Depending on the cabling used a grommet may be required to protect the cable where it enters the back box Wall Dock I nstallation The wall dock has a ribbon cable at the back of the unit which should be plugged into the back box PCB board before screwing the wall dock into place The wall dock is secured into the back box by four screws that protrude from the back Before offering the unit up to the back box ensure the screws are tight on the unit see fig1 so they Ensure securing screws rigidly protrude out from the unit This ensures that the screws all are tight against washer line up with the back box The four securing screws are accessible depending on whether the shelf is open or closed When ejected the two lower screws are accessible when closed the two upper screws are accessible via a long thin screw driver though the
8. rised territory All products returned to POLAR BEAR SOLUTIONS require a Return Material Authorisation RMA number The RMA number is obtained from the POLAR BEAR SOLUTIONS RMA Department The RMA number must be clearly marked on the outside of each box The RMA is valid for a 30 day period After the 30 day period the RMA will be cancelled Any shipments received not consistent with the RMA or after the RMA is cancelled will be refused POLAR BEAR SOLUTIONS is not responsible for products returned without a valid RMA number Products purchased from an authorised POLAR BEAR SOLUTIONS dealer should be returned via that dealer POLAR BEAR SOLUTIONS is not liable for any damages caused by its products or for the failure of its products to perform This includes any lost profits lost savings incidental damages or consequential damages POLAR BEAR SOLUTIONS is not liable for any claim made by a third party or by a POLAR BEAR SOLUTIONS Dealer for a third party This limitation of liability applies whether damages are sought or a claim is made under this warranty or as a tort claim including negligence and strict product liability a contract claim or any other claim This limitation of liability cannot be waived or amended by any person This limitation of liability will be effective even if POLAR BEAR SOLUTIONS or an authorised representative of POLAR BEAR SOLUTIONS has been advised of the possibility of any such damages This limitation of liability
9. warranty Polar Bear Solutions reserves the right to alter specifications without notice at any time For full warranty information refer to the Instruction Manual s associated with your Product s Polar Bear PB PWD9600 Installation Manual Tpit Rh Table of contents OVE W errs geste tty E E 4 ACI OVS GON e E E A A EA E E TEE E E 4 Wall DOCK NIG aaO aaea aan ATE EE 4 PONT SU eE E ER E A E A E 4 POWI UDD eee a E A E enetuclianetesetananiomainsaniaies 5 RJ45 Dry Contact Connector sssrinin a e aa Ea E EEE aS 5 BUOM Usage EX AIDS arnee aE EE EEE EE 5 Programmind a Lutron Cl DOOU irens a a 6 EB ECON ESP NO S N aee A T E A 6 MOG SSC a O S T AA 7 Contact Polar Bear Solutions lO sissstcsssstotesiwesstasswarnsecindsdenisitsedednssavasmonniednedsersiabaodegabiarnind 7 Polar Bear Solutions reserves the right to alter specifications without notice at any time For full warranty information refer to the Instruction Manual s associated with your Product s Polar Bear PB PWD9600 Installation Manual Bei Rr Overview The wall docking station is a flush mount in wall dock that allows the Philips TSU9600 control panel to be stored in wall and keeps the TSU9600 charged The docking station also has four optional dry contact closure buttons on the base for lighting or other automation integration The docking station comes in two parts the wall back box and the main docking station The wall back box comes with a built in PCB board to a
Download Pdf Manuals
Related Search