User manual Condor 3000 Transceiver
Contents
1. See 8 to display the name when selected 6 Memory banks The Condor has 7 memory banks each memory bank has its own 100 memory channels The advantage is that only channels in the selected bank will be scaned Select a higher bank Press 2 If the selected bank contains only empty memory channels the VCO mode will be activated otherwise the Condor switches over to the memory channels ode 7 Storing the callchannel It may be easy to activate the most used frequency by only pressing the button This frequency has to be programmed as follows Go to the VCO mode key S Choose the frequency and if nescesairy select SHIFT and CTCSS Press gt Press th Press E If you want give the call channel a name See for entering text 11 Press E again See 8 to enable the channel name S Enable channel name Display Kies Functie Aanroep freq Naam Every memorychannel can have its own name the displaying of the name can be enabled or disabled as follows Press E Press 6 9 Erase a memory channel Go to the momory mode key S Enter the channel to be erased Press E Press S Press E 10 Erase the callchannel Go to the callchannel key th Press E Press Lt Press E Display Kies Functie Display e FEE OK OK OK K Kies functie Kanaal wissen Display Kies functie Aanroep wissen 11 Entering te2. Bijwerken Vast Opslaan Alles wissen 21 855MHz 20 945MHz gt 20kHz raster Diagnose 19 Select call It is possible to store 10 names with corresponding tone code This tone codes can be transmitted with select call Select call Display Press E Kies Functie Press 0 Oproepen Choose the name to call Press Changing and storing names or codes Display Press E Kies Functie Press O Oproepen Choose the name or code to change Press E Naam Enter or change the name see 811 Press E to acknowledge Nr Enter or change the code Press 2 to acknowledge The key is used to acknowledge any other key to cancel
3. User manual Condor 3000 Transceiver Keypad overview MEN Main functions Keys Function 123456789 To enter a Channel frequency or number Scan Reverse shift Go to call channel Switch between VFO and Memory Toon squelch On Off DTSS 5 toon Choose second function of next key e gt a gt o Second function Keys Function Change transmitter power Chanhe squelch level Choose CTCSS tone TQ Activate MENU Activate status menu Show name of memory channel Choose channel spaceing Don t scan this memory channel Call with 5 TVO Shift none Choose tone squelch code Delete store call channel Delete store memory channel ONO Eto xO AU an After switching on the transceiver the selected frequency or channel will be shown at the upper line of the display After receiving a 5 TVO code the code will be printed at the second line of the display The selected memorybank is indicated at the right of the second line To use the second function of the keys press the button The text Kies funktie will appear on the second line of the display Now the second function of the next key will be activated To go back to the normal situation press again 1 Choose frequency The transceiver has three frequency modes with the S button can be changed from VCO to Memory The thirth mode is the call channel this one can be selected with the Th key VCO mode At VCO mode all frequencies at th
4. ds on four conditions The value selected in software The potentiometer on the front of the transceiver VSWR Temperature Changing power setting in software Display Press E Kies Functie Press 1 The power can be changed by pressing the buttons O and Acknowledge with any other key 15 Selecting repeater shift The value of the repeater shift on the 70cm version in usualy 1 6MHz and for the 2m version 600kHz This can be changed in the NEMU See 1 9 Switching on and off the shift Display Press E Kies functie Press It is possible to Switch off the shift 43 e Ae Negative shift Transmitter 1 6MHz lower 43 dolor RE o Shift positief Transmitter 1 6MHz higher Ass eee A 16 Reverse shift The reverse shift can be used to temporary listen at the transmitter frequency and transmit at the receiver frequency With this function the input of relais stations can be monitored The reverse shift can be switched on and off by pressing the key only without first pressing the key When reverse shift is switched on the S inthe display will be replaced by an R Als de reverse shift ingeschakeld is wordt de S in het display 17 Changing squelch level Display Press E Kies Functie Press 2 The squelch level can be changed by pressing the keys 0 and The squelch has four levels Most sensitive Squelch level is 5dB higher Squelch is normal but the recei
5. e choosen channel space 4 can be entered with the keypad The transceiver will fit the frequency to a legal value For the frequency 435 012 500 by a channelspace of 12 5kHz you have to enter SOL 435 012 500 Is the channelspace in this situation 25kHz the tranceiver will change the frequency to 435 000 000 Memory mode The Condor has the posibility to store 100 memory channels in one memory bank it has 7 memory banks 5 These channels are available in the memory mode In this mode each channel can have its own name of max 23 characters If the selected channel number is empty the Condor will generate an error beep and ignores the selected channel Callchannel mode If the callchannel is programmed 6 this frequency can be selected very quickly The advantage of the call channel is it can be selected by only pressing the Lt key 2 Choose CTCSS tone Some transceivers and repeaters are using CTCSS only transmitters which send a low frequency of 67 250Hz trough the modulation will be heard All others are ignored The frequency of this low tone can be selected as follows Display Press E Kies Functie Press 3 CTCSS The lowest frequency is 67Hz en the highest 250 3Hz between those values stands Geen it means none Select this one to switch off the CTCSS tone Switching on or off the CTCSS for the receiver press the amp button 3 Tone squelch The squelch can be closed u
6. ntil receiving a selected 5 tone code and the transmitter can send a selectable 5 tone code for the opposite station Activate De tonesquelch can be activated by the key for the receiver the yellow key will light on and for the transmitter a T will appear in the display Selecting code This code can be selected as follows Display Press E Kies Functie Press A RX Now select the tonecode for the receiver The code must be entered with the keys 0 9 when the number are flashing its a DTMF tone Press 2 TX Now select the tonecode for the receiver A tone burst will be generated by pressing the squelch open key while transmitting The tone burst frequency is selectable in the menu 4 Choosen channelspace Display Press E Kies Functie Press 8 Raster The channelspace can be changed by pressing the keys 0 en Acknowledge with another key 5 Storing memory channels It is posible to store 100 channels in each bank Store channels as follows Display Go to the VCO mode key S 43 so e Choose the frequency and if nescesairy select SHIFT and CTCSS Press T Kies Functie Press S Opslaan in xx Choose a number to store the channel When an arrow appears the choosen Opslaan in gt xx number 1s already used the old values will be overwritten Press 2 If you want give a name for this channel Naam See for entering text 11 Press again
7. ver less sensitive Squelch level 5dB less sensitive 18 The MENU It is impossible to give every function another button so the functions which are not used very often are placed in a MENU In this menu all items can be selected by pressing the keys O en The items can be changed by pressing the button In this situation the yellow led will light The menu can be selected as follows Press E Press 4 To prevent a mess in this menu some items are listed in sub menus This submenu s can be found in this main menu press E to step through this items To end this submenu press an unused key These are the menu items Shift This 1s the value of the repeater shift TX bij SO At onmogelijk the transmitter can t be activated when receiving a signal TX STOP TX time limiter When entering zero the TX STOP is disabled Bereik VCO range For 2 meter 144 146 100 200 Scan mode This is how the Condor acts when receiving a signal while scanning 1 Wait for silence 2 Wait a while 3 Stop at busy Audio TX mode This is a filter in the LF circuit Kies functie xxxxxxx MENU The possibilities A Hz Mogelijk Onmogelijk KEKEKE sec 430 440 300 500 Wacht op rust Wacht even Scan tot busy Submenu gt FM PM RX mode This is a filter in the LF circuit Onderdruk Surpress ZVEI tones Ptep Keypad beep on off Piep Ke
8. xt Text has to be entered the same way as entering text on a phone Entering the A B or the C has to be done by pressing the 2 a several times The C button is for eraseing a character the remaining characters are shifting back just like the DEL key in a wordprocessor The key is used to insert a space The characters behind every key are listed below With the arrow keys up and down um are used to step through the character group of the selected key The cursor has to be moved by pressing the arrow keys left 3 and right Give an acknowledge by pressing the key 12 Scanning Its possible to scan in VFO mode and Memory mode Scaming all frequencies Go to VFO mode with the key S Press Scanning the memorychannels Go to the memory mode with the key S Press Press any other key to stop scanning The red light indicates scanning If the transceiver has found a signal the scanning can be continued bu pressing again n 13 Lock out memory channels Scanning the memory channels will scan all channels in the selected bank With the lock out function each channel can be disabled for scanning It s posible to skip several memory channels while scanning Display Go to the memory key S Ce AS Choose the channel Press E Kies Functie Press The red light L indicates the lock out function To undo this repeat this 14 Transmitter power The output power of the transmitter depen
9. ypad beep volume Rogerptep Transmits a beeptone before switching off the DTMF tonen This is the length of the DTMF tones ZVEI tonen This is the length of the ZVEI tones Toon burst This is the frequency of the repeater tone burst Gebruiker Mijn nummer This is the personal 5 tone code of the user The condor gives alarm when receiving this code Antwoord At receiving the personal code another code can be transmitted This is the code to be returned Beantwoord This is to switch on and off the 5 tone answering Stappen This is the accelleration of the up and down key The longer this key is pressed the faster the the steps willl be Toetsen When holding a key for a while the can be repeated Autoatically FM PM Z WEI tonen Nooit Aan Uit Volume Aan Uit sete mS ok ok mS KKK Hz Submenu gt KKK KKK Wel Niet Versnel X Herhalen Eenmalig Instelling At bijwerken all settings will be stored At vast the settings can be stored manually by the next item When switching on the condor the last stored settings will be used Instelling The settings can be stored here Instelling All settings can be reset useing default settings IF This 1s the first IF LP filters This is the width of the LP filter for the receiver Status When the red error light burns the problem can be shown here by pressing the key
Download Pdf Manuals
Related Search