Network Quad User Manual
Contents
1. LIGHTS 610 0503 05 LIG 0 LIG 3 LIG 2 LIG 1 OFF High Medium Low 31 NETWORK ALARMS The Network QUAD unit has an internal buzzer that will sound when an alarm condition is met on a Network unit that has alarm functions ie Network DEPTH and Network QUAD for depth alarms and Network PILOT for Watch Alarm and Off Course alarms The unit will also display which alarm is activated To silence the internal alarm and return the display to normal operation press any of the five keys DEPTH ALARM DISPLAY NOT QUAD UNIT Depth alarms can be set for the following e Shallow water e Deep water Anchor Watch Check your Network DEPTH or QUAD unit to see which alarm is activated 610 0503 05 NETWORK PILOT ALARM DISPLAYS QUAD UNIT The Watch Alarm is a count down timer with is activated at the end of the preset count down period The display alternates between the messages below The Off Course alarm is activated when the boat deviates off course by preset amount display alternatesbetween the messages below 32 FAULT AND ERROR MESSAGES NETWORK PILOT FAULT DISPLAY NOT QUAD UNIT If the Network PILOT should have a fault the autopilot computer unit will send a message to all other Network Display Units The Network units2. ca 2888 CAL Manual boat speed and log calibration LOG Manual boat speed and log calibration e 5 25 CAL AUTO CAL Automatic boat speed and log calibration dr Reset Dead Reckoned Distance When SETUP mode SPEED SPEED key becomes the UP key A The LOG key becomes the DOWN key The LIGHTS key becomes the ENTER key DAMPING 8 The procedures for using the SETUP options the following pages 610 0503 05 SETTING THE DISPLAY Damping allows the response time of the displayed speed value to be slowed down if it is to jumpy in rough weather or to sped it up when the conditions are calm The damping works by averaging the values over a set time period the longer the time period the smoother the readings however the longer it takes to see a change Similarly the shorter it is the jumpier the readings but the faster the response The Network QUAD unit has a factory set value of 5 this can be adjusted in the range 1 to 64 each step is approximately one second E Ma NEW spe _ 5 DAMPING 2S DAMPING 2S SPEED SETUP SPEED Press SPEED key Press SETUP key Press ENTER key Use A or V to Press ENTER Press SPEED key to display current once to display if the value is to change the value memorise the to display current boat speed the
3. Network connector Network amp Power connector Sun cover LL Gasket cr Unit Mounting bracket Self tapping screws 35 SPECIFICATION PHYSICAL PARAMETERS Construction Window Display Dimensions Weight ENVIRONMENTAL Operating Temp Storage Temp Humidity Sealing 610 0503 05 High impact ABS plastic Acrylic Back lit Liquid Crystal Display Large Digits 15mm 0 6 Small Digits 10mm 0 4 110 x 110 x 25 4mm 4 x 4 x 1 Requires 65mm 2 6 depth behind bulkhead for display barrel 0 3 Kg 0 66lbs 10 55 14 to 131F 9399 RH 25 70 25 to 70C 9599 RH Up to 9596 RH Fully sealed front suitable for bulkhead cockpit mounting Vented barrel to prevent condensation ELECTRICAL Power Supply 12V DC nominal 10 to 16V Operating Current 40mA typical 100mA illuminated Protection Connect via external fuse or circuit breaker CABLES AND CONNECTIONS Connection to adjacent units is via cable tails fitted with either a plug or a socket Extension cables are available from your dealer The cable tails carry power and NMEAdata between units ALARM Internal audible alarm Control output for external alarm unit NMEA OUTPUT SENTENCES QUAD REPEATER ONLY The Network QUAD does not have NMEA output Heading IIVHW Speed and heading IIDBT Depth IIVWR Apparent wind angle and wind speed SIIMTW Sea temperature 36
4. CAL zero depth from transducer CAL positive depth from waterline CAL negative depth from keel NOTE If the CAL LOCK is set then the CAL value cannot be changed Consult your B amp G dealer for further advice Press DEPTH key Press SETUP key Press ENTER to Use A or V to to display depth to display current adjust the datum adjust the value datum CAL datum value The value The value display will flash will flash 610 0503 05 Press ENTER to value Press DEPTH to memorise the new display the depth datum 18 SETTING THE DEPTH UNITS The Network QUAD unit can be set to display depth in Metres Feet or Fathoms The selected units are used for displayed depth information on all Network instruments on the entire Network system DEPTH 55 METRES DEPTH METRES DEPTH METRES Press DEPTH key Press SETUP key Press ENTER key to display the twice The depth if the units are to current depth display will go be changed blank 610 0503 05 DEPTH METRES Use A V to change the units Za DEPTH FEET OOOO m Press ENTER key Press DEPTH to to memorise the display current change depth 19 DEPTH ALARMS The display will show OFF if the alarm is disabled or the alarm value when enabled The value will be displayed in metres feet or fathoms depending on the selected depth units When the alarm condition is met the unit will sound its internal ala
5. when the alarm was enabled Using the factory set values the water depth could increase to 4m 3m 1m and decrease to 2 5m 3m 0 5m before the alarm would sound DEEP limit The anchor alarm depth limits are shown alternatively when they are enabled and displayed using the DEPTH key 1 ALARM 25 taum ON 1 0m 0 5m SHALLOW limit 3 0m depth 610 HB 0503 05 SHALLOW ALARM at 2 5m 23 ENABLING DISABLING THE ANCHOR ALARM L Eu Mun Press DEPTH key Press SETUP Press ENTER Use A or V to Press ENTER Press DEPTH key to display key to display key the alarm enable or disable the to display the ANCHOR alarm state state display will the alarm new alarm state anchor alarm ALARM flash 610 0503 05 24 ADJUSTING THE ANCHOR ALARM SHALLOW LIMIT fp us SHALLOW SHALLOW HALLOW SHALLOW 0 5 iow 0 5 e Dru ran ae ON SETUP L3 c coss ENTER Press SETUP key Press ENTER key Use A or V to Press ENTER to Press DEPTH key twice to display the the value display change the value the new to display the value and enable anchor alarm shallow value will flash the alarm Press DEPTH key to display anchor alarm ADJUSTING THE ANCHOR ALARM DEEP LIMIT Press SETUP Press ENTER key Use A or V
6. 16 Nautical Miles or 100 metres per run If this is not achieved the AUTO CAL will fail and the procedure will have to be repeated Press the SPEED key to select current boat speed Press the SETUP key five times to display AUTO CAL 610 0503 05 Press the ENTER key when in line with marker A to start run 1 The display will flash AUTO CAL 1 Press ENTER key again when in line with marker B to freeze run 1 The display will flash showing the distance so far for one run Turn the boat around for run 2 in the opposite direction over the same measured distance Press the ENTER key when in line with marker B to start run 2 The display will flash AUTO CAL 2 Press ENTER key again when in line with marker A to freeze run 2 The display will flash the accumulated distance so far for two runs Turn the boat around for run 3 final run in the opposite direction over the same measured distance Press the ENTER key when in line with marker A to start run 3 The display will flash AUTO CAL 3 Press ENTER key again when in line with marker B to freeze run 3 The display will flash the accumulated distance for three runs Multiply the recorded distance from the chart by the number of runs completed This is the true distance travelled Adjust the flashing display with the or keys until it is the same as the true distance Press the ENTER key to complete the calibration The display will zero and the calibration is
7. AUTOPILOTS Network PILOT 610 0503 05 INTRODUCTION NETWORK QUAD The Network QUAD unit measures and displays Speed Depth Log Timer and Sea Temperature information on a large back lit Liquid Crystal Display LCD The LCD is divided into three display areas The top area permanently shows speed information the centre area is selectable and shows Log timer sea temperature and depth alarm information and the bottom area permanently shows depth information The five keys allow selection of the displayed information and setting of the units mode calibration factors and operating parameters It can operate as the main Network QUAD unit either alone or as part of an Integrated Network Instrument System taking inputs directly from Speed and Depth Sensors which plug into the sockets at the rear of the display or as a repeater by selecting repeater mode of information received via the two Network cable tails The Network QUAD REPEATER not a Network QUAD in repeater mode does not have Speed and Depth Sensor Sockets so it only receives data via the system network It offers identical facilities to a Network QUAD main unit but can only ever be used as a repeater INTRODUCTION NETWORK QUAD CONT D The Network QUAD unit has three adjustable alarms 1 Shallow water alarm 2 Deep water alarm 3 Anchor alarm An internal alarm buzzer will sound when an alarm condition is met and the display will flash The alarm is br
8. key to display the twice the value is value display adjust the value to memorise the the value is shallow alarm displayed will flash new value displayed and the alarm enabled 610 0503 05 21 ENABLING DISABLING THE DEEP ALARM DEEP DEE DEEP DEEP DEEP DEEP F ALARM ALARM B AAR 0 0 ALARM DEPTH SETUP Press DEPTH Press SETUP key Press ENTER key Use A or V to Press ENTER to Press DEPTH key to display the deep the alarm state will the alarm state enable disable the the the current value is alarm be displayed display will flash alarm change displayed ADJUSTING THE DEEP ALARM VALUE n T 1 pw poU freee Press DEPTH Press SETUP key Press ENTER key Use A or V to Press ENTER Press DEPTH key to display the deep twice the value is the value display adjust the value to memorise the the value is alarm displayed will flash new value displayed and the alarm enabled 610 0503 05 22 USING THE ANCHOR ALARM The Anchor Alarm uses two adjustable alarm limits The alarm will sound if the water is deeper or shallower by the set values than the original depth of water when the alarm was enabled This allows you to adjust your anchor chain according to the tides The Network QUAD unit has a factory set Shallow limit of 0 5m and Deep limit of 1 0m In the following example the original water depth was 3m
9. mark the centres of the holes for the self tapping screw the fixing stud holes and the mounting bracket e template allows 4mm 5 32 between adjacent units for the suncover increase this distance if required to maximum of 60mm 2 3 8 between units or 180mm 3 1 8 between centres For greater distances between units extension cables available e Use a 70mm 2 3 4 diameter hole cutter for the mounting bracket hole e Use a 2 9mm for the self tapping screw holes Use a 5mm 3 32 drill for the locking stud holes e Secure the mounting bracket to the bulkhead with the self tapping screws supplied e Fit the rubber sealing gasket around the mounting bracket e Screw the locking studs into the back of the display head if required e Carefully pass the cable tails through the mounting bracket hole connect the cables to the main units e Clip the display head into the mounting bracket e Secure the instrument with the thumb nuts supplied 34 INSTALLATION DATA 110 0mm Network eS Network QUAD 110 0m SPEED DEPTH TIMER SETUP LIGHTS EN NN ne Mounting bracket 82 0mm t 82 0 610 0503 05 25 0mm 65 0mm Rubber Gasket Fit the gasket around the mounting bracket Bulkhead Gasket Locking stud fixing Speed sensor connector Depth sensor connector
10. memorised 13 AUTOMATIC CALIBRATION PROCEDURE Distance measured on a chart X 0521 _ p cocwo SPEED turo 3 0 650 E SPEED NEN E SETUP SPEED 610 0503 05 14 RESETTING THE DEAD RECKONED DISTANCE This facility allows the Dead Reckoned DR distance log to be reset The Network QUAD unit cannot display the DR information however Network SPEED and Network DATA both display it Hit COCO r3 EB EN EN Press SPEED key to Press SETUP key 6 times Press ENTER key there The dr log will be reset to display the current boat to display dr The display will be no change on the zero when displayed on speed will flash QUAD unit LCD but the dr SPEED or DATA units log has been reset 610 0503 05 USING THE DEPTH KEY The current water depth is permanently displayed in the bottom LCD area in metres feet or fathoms The unit is factory set to metres The depth displayed is from the depth datum see DEPTH DATUM Press the DEPTH key to cycle through the following options CAL SHALLOW ALARM DEEP ALARM ANCHOR ALARM The Depth Datum can be adjusted so the displayed water depth is from the water line the depth sensor transducer or the keel or outdrive depth The unit is factory set to display water depth from the transducer When enab
11. will alternately display the following message the actual fault will have to read from the Network PILOT Display unit 610 0503 05 UNIT INTERNAL ERRORS In the unlikely event that your Network QUAD unit should develop an internal error the unit will sound its alarm continuously and the display will show an error number Press any of the keys to reset the error condition and silence this alarm In some cases the fault can be cleared by switching off the instruments at the supply waiting a few moments and then switching on again If either of these methods does not clear the fault the error number should be recorded Switch off the supply and disconnect the faulty unit Return it with the error number to your dealer for servicing 33 INSTALLATION The display heads are supplied with a clip in mounting bracket which allows for easy installation access from behind is not necessary to secure the unit in place However to prevent theft and permanently fix the unit in position locking studs and thumb nuts are supplied SITING THE UNIT All Network Instruments are designed for mounting on or below deck A mounting position should be selected where they are Easy to read by the helmsman On a smooth and flat surface At least 100mm 4 from a compass Accessible from behind for fitting locking studs if required 610 0503 05 MOUNTING THE UNIT Use the cutting template supplied to
12. AD QUAD Main unit Repeater Mode Repeater Mode Repeater unit SPEED 625 SPEED 625 SPEED 625 SPEED 625 25 6 25 6 125 6 125 6 DEPTH 55 IDEPTH 55 IDEPTH 155 DEPTH 155 Depth Speed Sensor Sensor When repeater mode if the data is not being received from the system network the prr display will show OFF when a key is 610 0503 05 C S50 QUAD WIND QUAD PILOT SPEED 625 P 328 125 6 AUTO comp DEPTH SS 35 RN ci Depth Sensor Speed L4 Sensor If the Network QUAD unit losses valid depth data due either the actual depth being outside the working range or to extreme turbulence in the water the LCD will show 3 floating bars This shows that the unit is attempting to calculate the depth and is still functioning ae pe ER CO LJ L3 C3 L3 CO LJ CO C3 L3 SELECTING THE DISPLAY MODE The Network QUAD unit has two operating modes The correct mode must be selected for your Network system to operate properly tYPEt Transducer mode the unit uses and displays speed and depth data from sensors connected directly into the display unit tYPEr Repeater mode the unit operates as a repeater us
13. CONTENTS GENERAL INTRODUCTION TO B amp G NETWORK 2 INTRODUCTION TO NETWORK QUAD 3 EXAMPLE SYSTEMS USING NETWORK QUAD 4 SELECTING THE DISPLAY MODE 5 USING THE SPEED KEY 6 CALIBRATION AND OPERATING PARAMETERS 7 SETTING THE DISPLAY DAMPING 8 SETTING THE SPEED AND LOG UNITS 9 SPEED AND LOG CALIBRATION 10 1 MANUAL CALIBRATION CAL 11 2 MANUAL CALIBRATION LOG CAL 12 AUTOMATIC CALIBRATION AUTO CAL 13 RESETTING THE DEAD RECKONED DISTANCE 15 USING THE oes eoe 16 THE DEPTH DATUM CAL 17 SETTING THE DEPTH 18 SETTING THE DEPTH UNITS eae 19 DEPTH ALARMYS 20 SHALLOW ALARM ENABLING DISABLING THE SHALLOW ALARM 21 ADJUSTING THE SHALLOW ALARM VALUE 21 610 0503 05 DEEP ALARM ENABLING DISABLING THE DEEP ALARM 22 ADJUSTING THE DEEP ALARM VALUE 22 ANCHOR ALARM USING THE ANCHOR 23 ENABLING DISABLING THE ANCHOR ALARM 24 ADJUSTING THE ANCHOR ALARM SHALLOW LIMIT 25 ADJUSTI
14. LL mp 106 e 3 TIMER JCJ MCI LI TEMP 26 RESETTING THE TRIP LOG The Trip Log is reset to zero and starts again as soon as the ENTER key is pressed 1065124 TAP LOG OO LEN Press TIMER key to Press SETUP key Press ENTER key the display the TRIP LOG Display flashes display resets to zero and remains flashing 610 0503 05 Press TIMER key to display the TRIP LOG 27 SETTING THE TIMERS AND LAP TIMER Lap Timer be used to freeze the displayed time with any of the three Timers ENTER Press the TIMER Press SETUP key Press ENTER key to display the 1 10 min key the display is timers 2 5 min set to the 3 Count up selected starting The display will value The timer flash starts to count 610 0503 05 Press TIMER key the display stops flashing and the timer is running Press TIMER key Press TIMER key to freeze the 4 times to display displayed time the timer again The timer is still counting but not displayed 28 SETTING THE TEMPERATURE UNITS The sea temperature can be displayed in Celsius or Fahrenheit TMER cC sas TEMP Press TEMP key Press SETUP Press ENTER if Use A or V keys Press ENTER key Press TEMP key until the sea once to display the units are to be to change the to memorise the to dis
15. NG THE ANCHOR ALARM DEEP LIMIT 25 USING THE TIMER TEMP KEY 26 RESETTING THE TRIP 27 SETTING THE TIMERS AND LAP TIMER 28 SETTING THE TEMPERATURE UNITS 29 CALIBRATING THE TEMPERATURE SENSOR 30 USING THE LIGHTS KEY i eene 31 NETWORK ALARMS 32 FAULT AND ERROR MESSAGES 33 INSTALLATION aieeaa aA aaa 34 SITING THE BIET tons es deett vie eie 34 MOUNTING THE UNIT 34 SPECIFICATION 36 GENERAL INTRODUCTION B amp G NETWORK The B amp G Network range of instruments is designed to be used as individual units or connected together to form an integrated navigational system A single network cable is used to carry data and power between units The latest technology and screened cables throughout the Network System ensure the ultimate protection from interference between units and other systems All Network instruments can be linked to Network PILOT Network CHART Network GPS or Network LORAN receivers or via NMEA 0183 v1 5 to other navigational equipment INSTRUMENTS Network SPEED Network DEPTH Network QUAD Network WIND Network TACK Network DATA NAVIGATIONAL AIDS Network NAV Network GPS Network LORAN LCD CHART
16. damping be changed change boat speed value 610 0503 05 8 SETTING THE SPEED AND LOG UNITS The Network QUAD can be set to display boat speed in Knots or MPH If boat speed is in Knots then log is in Nautical Miles If boat speed is in MPH then log is in Statute Miles SPEED 6 rs SPEED _ SPEED eos mors ZNI Press SPEED key Press SETUP key Press ENTER key Use A or V to Press ENTER Press SPEED key to display current twice The speed if the units are to change the units to memorise the to display current boat speed digits will blank be changed change boat speed 610 0503 05 9 SPEED AND LOG CALIBRATION Before Network QUAD is used for navigation the boat speed and log have to be calibrated to ensure accuracy for your installation and the boats hull characteristics Three methods are available with the Network QUAD unit two manual adjustments and one automatic MANUAL CALIBRATION 1 CAL The displayed boat speed value is corrected manually to read a known measured speed 2 LOG The units calibration figure Hz Knot is CAL manually adjusted to correct log and speed inaccuracy AUTOMATIC CALIBRATION 3 AUTO CAL The unit automatically calibrates and corrects the boat speed and log Use the one of the methods overleaf to calibrate your instrument It is recommended that AUTO CAL is used as this method will ensure the most accurate calibration of your Netw
17. ing data from the system network _ coc oo SETUP OOo Press TIMER key Press SETUP key PressENTERkey Use A or V to to display stored to display the ifthe mode needs change mode log current mode to be changed 610 0503 05 Press ENTER to store the new mode in memory Press TIMER to complete the change USING THE SPEED KEY Boat speed information is permanently displayed in the top area of the LCD Press the SPEED key to cycle through the following tB Jas options SPEED Current boat speed in Knots can also be displayed in MPH KNOTS MAX Maximum boat speed since the last reset 5 E SPEED ofthe trip log AVERAGE Average boat speed since the last reset of SPEED the trip log SPEED 610 HB 0503 05 CALIBRATION AND OPERATING PARAMETERS When current boat speed is displayed press the SETUP key to cycle through the following options DAMPING The response time of the display to dr changes in boat speed SPEED The boat speed can be displayed in Knots KNOT or MPH This setting also changes the log units to Nautical or Statute Miles
18. led it will sound if the water depth is less than the alarm value When enabled it will sound if the water depth is more than the alarm value When enabled it will sound if the water depth is outside two alarm limits The Network QUAD unit can measure and display water depth in the following ranges e 0 7 to 180 metres e 2 4 to 590 0 37 to 98 4 fathoms Accuracy 2 or 0 2m 8 610 0503 05 OFF mw OFF ALLOW ALARM ca lg DEPTH v 16 THE DEPTH DATUM CAL The depth datum CAL is an offset calibration value used to determine the displayed information reference point It is added to the actual measured water depth to display the depth from the waterline the depth sensor transducer or the keel outdrive depth The Network QUAD unit has factory set CAL of zero i e the depth is displayed from the transducer The CAL value is displayed in the same units as the depth Sail Boat Power Boat 610 0503 05 Keel depth Datum value positive depth measured from waterline Datum value 0 0 depth measured from transducer Datum value negative depth measured from outdrive Datum value negative depth measured from keel 17 SETTING THE DEPTH DATUM
19. oadcast to all other Network Instruments in an integrated system they will also sound their alarms and flash their displays except Network WIND and Network TACK The Network QUAD unit is NOT able to transmit NMEA 0183 v1 5 however the Network QUAD REPEATER unit is able to transmit NMEA data via the system network cables to other Network units and connect to an NMEA device e g a position fixer with a special NMEA output cable IMPORTANT NOTE Your Network QUAD unit must be set up and calibrated correctly before it is used as part of a navigational system 610 0503 05 NETWORK QUAD DISPLAY UNIT B amp G Network QUAD N SPEED 6 25 KNOTS 30 1 DEPTH 55 METRES SPEED DEPTH TIMER SETUP LIGHTS NS X EXAMPLES SYSTEMS USING NETWORK QUAD Only one Network QUAD unit should have speed and depth sensors connected to it and set to transducer mode Up to three more Network QUAD set to repeater mode or QUAD REPEATER units can be connected on to the system network QUAD QUAD QU
20. ork QUAD unit 610 HB 0503 05 10 METHOD 1 MANUAL CALIBRATION CAL This procedure requires a reference boat speed with which to compare the Network QUAD units displayed boat speed For example another boat with an accurate calibrated log or if the top speed of the boat is known this value can be entered during a sea trial to correct the displayed value NOTE The accuracy of this method is dependent upon the accuracy of the reference boat speed The example below shows a displayed boat speed of 5 2 knots the boat speed is known to be 6 0 knots The displayed value is adjusted to read 6 0 knots SPEED E L3 C3 C C3 Press SPEED key to display current boat speed Press SETUP key three times to display CAL Press ENTER key to adjust the displayed value 610 0503 05 IMPORTANT NOTE This method of calibration must not be carried out at boat speeds of LESS THAN 3 KNOTS as inaccurate values can be entered into the units memory If the speed and log are not functioning correctly then enter a calibration value of 5 3 to 6 2 and then re enter the correct calibration value as described below o 21 Dos Use A or V to change the value Press ENTER to store the new value in memory Press SPEED key to complete the change 11 METHOD 2 MANUAL CALIBRATION LOG CAL If the log or boat speed is in error by a known percentage then this method allows the calibration fig
21. play sea temperature is the current units changed The displayed units new units temperature displayed display will flash 610 0503 05 29 CALIBRATING THE TEMPERATURE SENSOR Temperature calibration should only be carried out when the built in sea water temperature sensor part of the speed sensor is considered to be inaccurate The temperature of the water will have to be measured with an accurate temperature sensing device this value can then be entered into the Network QUAD unit In the following example the unit is displaying a reading of 10 4 C the water temperature is known to be 11 4 C correct value is entered into the Network QUAD unit ca BYE calf YOR ENTER TEMP Press TEMP key Press SETUP key Press ENTER if Use A or V keys Press ENTER key Press TEMP key until TEMP is twice to display required to to change the to memorise the to display sea displayed CAL change the displayed value new value temperature displayed value The display will flash 610 0503 05 30 USING THE LIGHTS KEY The Network QUAD Display unit has 3 levels of illumination and off controlled by the LIGHTS key It also changes the illumination level of the key legends The LIGHTS key is always illuminated so even in complete darkness the key can be located LIGI Lib3 _ Lib
22. rm buzzer and flash DEPTH METRES Silence the alarm by pressing any key The alarm information is broadcast to all other Network units via the system network cables these will also sound their alarms and flash their displays except Network WIND and Network TACK which do not have alarms See NETWORK ALARMS at the end of this manual Shallow Alarm Factory set to 1 0m 3 2ft 0 5 fathoms Adjustable range 0 180m 0 590ft 0 98 4 fa SHALLOW LB uoi a ON 610 HB 0503 05 Deep Alarm e Factory set to 10 0m 32 8ft 5 4 fathoms Adjustable range 0 180m 0 590 ft O 98 4 fa TUNES Anchor Alarm e Factory set Shallow 0 5m Deep 1 0m e 1 6 3 2ft 0 2 5 fathoms e Adjustable range 0 180m 0 590 ft O 98 4 fa d D 05 Laan 1 20 ENABLING DISABLING THE SHALLOW ALARM id F F ALARM HALLOW cow pec Press DEPTH Press SETUP key Press ENTER key Use A or V to Press ENTER to Press DEPTH key to display the the alarm state will the alarm state enable disable the the the current value shallow alarm be displayed display will flash alarm change is displayed ADJUSTING THE SHALLOW ALARM VALUE Press DEPTH Press SETUP Press ENTER key Use A or V to Press ENTER key Press DEPTH
23. to Press ENTER to Press DEPTH key 3 times to display value display change the value the new display the value and enable anchor alarm the deep value will flash the alarm Press DEPTH key to display anchor alarm 610 0503 05 25 USING THE TIMER TEMP KEY Press the TIMER TEMP key to cycle through the options TRIP LOG A reset log that can be displayed in Nautical miles or Statute Miles This is determined by the selection of the displayed speed units see SETTING THE SPEED AND LOG UNITS It also resets the Maximum and Average Speed values LOG The Stored Log in NM or M as above TIMER There are three timers available 1 10 minute count down 2 5 minute count down 3 Count up starting from zero e 10 minute count down timer sounds a bleep at 5 and 1 minute and then at 30 20 10 5 4 3 2 1 seconds e 5 minute count down timer sounds a bleep at 1 minute and then at 30 20 10 5 4 3 2 1 seconds e All the timers count one second intervals up to 99 hours 59 minutes and 59 seconds e When a count down timer reaches zero it will begin to count up e All timers have a Lap Time facility that will freeze the displayed time while the timer remains counting 610 0503 05 SEA TEMPERATURE The Sea Temperature is displayed in C Celsius or F Fahrenheit 000000 10 Jet 4 C L
24. ure or LOG CAL to be adjusted by that amount The calibration figure is measured in Hertz per knot Hz kt the factory set value is 6 25 NOTE The accuracy of this method is dependant upon the accuracy of the calculated percentage error Using the factory set LOG CAL of 6 25 Hz kt e display is under reading by 10 subtract 0 62 e lf the display is over reading by 10 add 0 62 SETUP SPEED E L3 C3 O3 C3 Press SPEED key Press SETUP key Press ENTER key Use A or V to Press ENTER to Press SPEED key to display current four times to to adjust the change the value store the new to complete boat speed display LOG displayed value value in memory change CAL 610 0503 05 12 METHOD 3 AUTOMATIC CALIBRATION AUTO CAL This procedure will automatically and accurately calibrate the boat speed and log and is the recommended method for most boats NOTE AUTO CAL can be aborted any time by pressing the SETUP key then the SPEED key Select two markers that are easily identifiable on the ground and on a chart choose a place where the current is at a minimum Measure and record the distance between the markers on the chart t is recommended that three runs are carried out this accounts for tidal efforts and improves accuracy However a time should selected when the current is at a minimum ie slack water between tides IMPORTANT NOTE The total distance accumulated over the three runs must exceed 0
Download Pdf Manuals
Related Search