OPERATORS MANUAL
Contents
1. CAPCOM CO LTD 1997 ALL RIGHTS RESERVED CAPCOM U S A INC 1997 ALL RIGHTS RESERVED OPERATORS MANUAL WARNING This game is for use in the United States of America and Canada Sales export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited Violators are subject to severe penalties and will be prosecuted to the full extent of the law CANTI COIN OP INC 3311 N Kennicott Avenue Arlington Heights Illinois 60004 00186 847 797 6192 022897 847 797 6306 coin op inc STREET FIGHTER THREE THANK YOU FOR PURCHASING STREET FIGHTER THREE WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME CAPCOM COIN OP INC ATTN FIELD SERVICE VIDEO PRODUCTS 3311 N KENNICOTT AVENUE ARLINGTON HEIGHTS ILLINOIS 60004 PHONE 847 797 6192 SERVICE 847 797 6320 PARTS FAX 847 797 6306 THE SERIAL NUMBERS OF YOUR GAME ARE LOCATED AS SHOWN BELOW PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION PLEASE RECORD THE AAMA SERIAL NUMBER HERE 1 AAMA SERIAL NUMBER PLEASE APPLY PRODUCT SERIAL NUMBER STICKER HERE CAPON co op inc STREET FIGHTER THREE TABLE OF CONTENTS Warranty Information ii Kit Inspection Kit Installation Preparation 2 Installation 2 Marquee 22. OR 27 OR 28 Table 1 Test Volume Bracket Wiring Chart Proprietary and confidential information not to be disclosed or copied without the express permission of CAPCOM COIN OP INC CAPE coin op inc STREET FIGHTER THREE SYSTEM CONFIGURATION CHANGING THE SYSTEM CONFIGURATION 7 1 SYSTEM CONFIGURATION SETTINGS gt 1 COIN MODE 2 COINS 1CREDIT CHUTE TYPE 2 CHUTES SINGLE ONT Move the PLAYER 1 JOYSTICK up or down to highlight the DEMO SOUND ON desired option Once the option is highlighted move the SOUND MODE STEREO PLAYER 1 JOYSTICK left or right or press the PLAYER 1 EXIT PUNCH LIGHT button to select SELECT OPTION 1P MODIFY SETTING 1P LEFT OR RIGHT 1P SHOT1 OR SHOT2 UP OR DOWN SYSTEM CONFIGURATION ITEM DESCRIPTIONS 2 CHUTE TYPE SELECT THE CHARGE PER PLAY SELECT THE NUMBER OF PLAYER S AND COIN CHUTES 1 CHUTE SINGLE WITH THIS SETTING EITHER PLAYER CAN START THE GAME 2 CHUTES SINGLE TWO PLAYERS USE ONE COIN CHUTE AND PLAY AT THE SAME TIME THE PLAYER WHOSE COIN WAS PUT IN FIRST STARTS THE GAME 2 CHUTES MULTI TWO PLAYERS USE TWO COIN CHUTES AND PLAY SEPARATELY THE GAME STARTS FROM THE SAME SIDE AS THE COIN CHUTE WAS USED 3 CONTINUE USED TO SET THE CONTINUOUS PLAY 4 MONITOR USED TO FLIP SCREEN IF SCREEN APPEARS UPSIDE DOWN CHANGE THE SETTING 5 DEMO SOUND TURNS ATTRACT SOUNDS ON OR OFF 6 SOUND MODE SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABIN
3. 1 PLAYER UP 1 PLAYER DOWN 1 PLAYER LEFT 1 PLAYER RIGHT 1 PLAYER PUNCH LIGHT 1 PLAYER PUNCH MIDDLE 1 PLAYER PUNCH HEAVY VIDEO GREEN VIDEO SYNC SERVICE FREE CREDIT z 2 PLAYER PUNCH HEAVY WHITE BLACK WHITE BROWN WHITE RED WHITE ORANGE WHITE YELLOW WHITE GREEN WHITE BLUE ao Ta NECO 5 o o AO el ee ee NC porem NIC sw GND Table 2 JAMMA Wiring Connections Wire Color Note Wire colors shown are according to the AAMA AMOA Standard for wire color assignments your harness may contain different colors than shown above CONNECTOR EVEN ROW INC 1 E Ne PURFLEVELLOW WIRE COLOR vc PURPLE YELLOW N C 1 MINCE Le eel NC 2521 6 22 NIC NIC RED PLAVERIKICK MIDDLE NIC NIC NIC PINK YELLOW NIC PESO DERE ee NC a pu NC ee eel NIC NO CONNECTION PINK YELLOW NIC PLAYER T COMMON BLACK Table 3 Auxiliary Cable Wiring Connections Proprietary and confidential information not to be disclosed or copied without the express permission of CAPCOM COIN OP INC 10 1 3 16 DRILL FOR 1P OR 2P START BUTTON SWITCH 1 3 4 DRILL FOR pallid ee a ccd JOYSTICK HOLE 5 oo 1 3 16 DRILL FOR BUTTON SWITCH HOLES CAPCOM INC NORTH KENRICOTT AVENUE p INC PX ES 79513 GANTS coin op inc REFERENCE INFORMATION PC BOARD CONNECTIONS AND CONTRO
4. Control Panel Components 3 Cabinet Decals 2 Wiring Control Panel 3 10 Test Volume Bracket 3 7 PC Boards 4 5 CD DRIVE 4 5 Game Adjustments Test Menu 6 Accessing the Menu 6 How to Select an Item 6 Closing the Menu 6 Menu Item Descriptions 6 Configuration Menu 7 System Configuration 8 Game Configuration 9 Reference Information JAMMA Connections 10 Auxiliary Cable Connections 10 CAUTION Please read the following instructions to keep the PC boards in good condition Do not drop or bump the boards Do not spill any liquids on the boards DISASSEMBLING THE BOARDS OR REMOVING STICKERS MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY Proprietary and confidential information not to be disclosed or copied without the express permission of CAPCOM COIN OP INC CAPETI coin op inc STREET FIGHTER THREE LIMITED PRODUCT WARRANTY APPLIES TO DOMESTIC SALES ONLY CAPCOM COIN OP INC Seller warrants only to the initial purchaser of its products that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified A Printed Circuit Boards Ninety 90 Days B Electronic and Mechanical Components Ninety 90 Days No other part of Seller s products are warranted Warranty periods are effective from the initial date of shipment from seller to its authorized distributors Seller s sole liability shall be at its option
5. new holes should go Center punch any needed new holes on the control panel 5 Cut out the new holes using a 1 3 16 hole saw 6 Ifthere is an additional control panel cover figure 1 such as plastic or lexan that will be utilized cut any additional holes using the same template cover is not included in the kit 7 Plug up unused holes with a wood dowel 1 1 8 diameter and sand any rough edges INSTALLATION Marquee Installation 8 Remove the marquee plexi glass marquee overlay and the cabinet graphics 9 Install the new marquee and replace the plexi glass Clear plexi glass is included in full kit Control Panel Overlay Installation See Figure 1 10 The control panel overlay in the kit is oversized to accommodate most control panel sizes Center the overlay on the control panel leaving some excess material at the edges 11 Remove the protective backing from the overlay and press it down on the control panel keeping it properly aligned Press it down firmly smooth out any bubbles and press it over the edges 12 Trim any excess from the overlay Place the drill hole template on top of the overlay aligning it with the joystick holes Pierce through the overlay at each control panel hole Then cut away overlay material covering the joystick and button holes Remove the template and clean offthe overlay t2 STREET FIGHTER THREE 13 Peel off the backings of the 6 button and joystick deca
6. to repair or replace products which are returned to Seller during the warranty periods specified provided A Seller is notified promptly upon discovery by buyer that stated products are defective B Such products are properly packaged and then returned prepaid to Seller s designated plant This warranty does not apply to any parts damaged during shipment or handling or due to improper installation or usage or alteration In no event shall Seller be liable for any anticipated profits loss of profits loss of use incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM COIN OP INC product WARRANTY DISCLAIMER EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IMPORTANT NOTICE THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT 1 coin op inc STREET FIGHTER THREE m KIT INSPECTION CHECK THAT ALL OF THE FOLLOWING PARTS HAVE BEEN SHIPPED WITH YOUR KIT IF ANY PARTS ARE MISSING CONTACT YOUR DISTRIBUTOR IMMEDIATELY SFNG1000 KIT PARTS
7. ET NOTE STEREO SHOULD ONLY BE SELECTED FOR USE WITH CAPCOM QSOUND CABINETS OR THE CABINET EQUIPPED STEREO POWER AMPLIFIER 7 EXIT TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU HIGHLIGHT THIS ITEM AND PUSH THE PLAYER 1 START BUTTON SYSTEM CONFIGURATION OPTION SETTINGS ICOIN 1 COIN 1 COIN 1 COIN 1 COIN 1 COIN 1 COIN 1 COIN 1 COIN yoo 2 COINS 3 COINS 4 COINS 5 COINS 6 COINS 7 COINS 8 COINS 9 COINS 2 COINS START FREE PLAY iem 7 ZCHUTES SINGLE ON 2 porre ecu ri 1 COIN 4 MONITOR 5 DEMO SOUND 6 SOUND MODE STEREO NOTE FACTORY SETTING 8 Proprietary and confidential information not to be disclosed or copied without the express permission of CAPCOM COIN OP INC CAPON co op inc STREET FIGHTER THREE GAME CONFIGURATION 7 2 GAME CONFIGURATION CHANGING THE GAME CONFIGURATION 1 SETTINGS 1 GAME DIFFICULTY EASY 3 HARD 2 DAMAGE LEVEL LOW 2 HIGH 3 TIMER COUNT SPEED sow ai AST Move the PLAYER 1 JOYSTICK up or down to highlight the 4 MAX ROUND 3 ROUNDS desired option Once the option is highlighted move the 5 EVENT OFF PLAYER 1 JOYSTICK left or right or press the PLAYER 1 6 EXIT PUNCH LIGHT button to select SELECT OPTION 1P UP OR DOWN MODIFY SETTINGS 1PLEFTOR RIGHT 1P SHOT1 ORSHOT2 GAME CONFIGURATION ITEM DESCRIPTIONS SETS THE DIFFICULTY LEVEL SETS THE OFFENSIVE POWER LEVEL SE
8. LANCE AND SOLID BLACK BACKGROUND DOT CROSS HATCH USED TO TEST THE SCREEN SIZE FOCUS AND DISTORTION GAME DATA COIN METER AND PLAYTIME INFORMATION WILL BE DISPLAYED CONFIGURATION USED TO CHANGE THE GAME PLAY SETTINGS REFER TO THE CONFIGURATION MENU SECTION MEMORY CHECK USED TO TEST MEMORY OK APPARS WHEN EACH BLOCK OF MEMORY PASSES TEST NG APPEARS IN CASE OF MALFUNCTION IF NG APPEARS REPEAT THE MEMORY TEST AND WAIT FOR THE OK MESSAGE CONTACT YOUR DISTRIBUTOR IF NG STILL APPEARS IN CASE THE GAME IS NOT FUNCTIONAL PROPERLY REWRITE THE DATA TO THE MOTHER BOARD 4 IF YOU SHOULD CONTINUE TO HAVE PROBLEMS REWRITING THE PROGRAM CONTACT YOUR 2 DISTRIBUTOR WARNING THIS FUNCTION WILL TAKE 20 MINUTE 33 NEVER TURN THE POWER OFF DURING THE PROCESS EXIT SELECT THIS ITEM AND PUSH THE PLAYER 1 PUNCH LIGHT BUTION TO RETURN TO GAME PLAY MODE GAME REWRITE Proprietary and confidential information not to be disclosed or copied without the express permission of CAPCOM COIN OP INC CAPETI coin op inc STREET FIGHTER THREE CONFIGURATION MENU The configuration menu is used to change various game settings such as level difficulty credits sound configuration etc These settings are stored in memory on the PCB rather than DIP switches The configuration menu is divided into 2 sections In the SYSTEM section you can change credits sound and coin door configurat
9. LIST PART NO DESCRIPTION SFNG1400 ASSY PCB CP3 SYSTEM STREET FIGHTER THREE SFNG4001 SECURITY CARTRIDGE STREET FIGHTER 1 THREE SFNG4002 CD ROM DISK STREET FIGHTER THREE O OS 00741 ASSY CD ROM DRIVE PIECE TYPE PIECE TYPE SC00101 02 SCREW S 2XIAPPHSEMSZC 4 5 00104 5 SCREW STS48X5 8PPH AB ZC FORWOOD 4 GE1200_ MONITORCARD 1 00376 PLEX MARQUEE CLEAR 27 0 X 9 0 X 1 8 O 00147 DECAL CABINET SIDE IEEE PUES AW00216 OVERLAY CONTROL PANEL eee SFNG SFNG 2 1 AW00245 3 DECAL JOYSTICK amp BUTTON SWITCHES 1 SFNG PM00186 MANUAL OPERATORS SFNG 03 0104 HARNESS STEREO SPEAKER SWITCH BUTTON RED Proprietary and confidential information not to be disclosed or copied without the express permission of CAPCOM COIN OP INC CAPCOM coin op INC KIT INSTALLATION WARNING MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION PREPARATION 1 Disconnect and remove the old printed circuit board s from the cabinet 2 Remove or open the control panel and disconnect and remove the buttons and joystick s from the control panel 3 Remove any covering from the control panel overlay and then remove the control panel overlay 4 Place the drill hole template over the control panel to determine where any
10. LS Volume Control Knob Stereo Audio Connector Test Switch TYPICAL CONTROL PANEL LAYOUT OF STREET FIGHTER THREE LIESTO priim KERNS SY manm TY map Wm WANIE STREET FIGHTER THREE Cartridge 1600200 NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING Federal law provides severe civil and criminal penalties for the unauthorized reproduction distribution or exhibition of copyrighted audiovisual works and video games The Federal Bureau of Investigation investigates allegations of criminal copyright infringement NT eT COIN OP INC 3311 N Kennicott Avenue Arlington Heights Illinois 60004 Phone 847 797 6192 Fax 847 797 6306 Copyright 1997 CAPCOM cOIN oP INC All Rights Reserved
11. TS THE SPEED OF THE COUNTDOWN 4 MAX ROUND SETS THE NUMBER OF ROUNDS PER MATCH FOR VS CPU I ROUND WINNER OF A SINGLE ROUND WINS 3 ROUNDS WINNER OF 2 OUT OF 3 ROUNDS WINS 5 ROUNDS WINNER OF 3 OUT OF 5 ROUNDS WINS TURNS ON EVENT MODE USEFUL FOR CHAMPIONSHIP TOURNAMENT OFF NORMAL SETTING SETS THE MODE TO NORMAL OPERATION ON MATCHES PLAYER WITH ONE CREDIT A WIN OR A LOSS RESULTS IN GAME OVER CONTINUE IS NOT AVAILABLE 6 EXIT RETURN TO THE CONFIGURATION MENU GAME CONFIGURATION OPTIONS 1 DIFFICULTY ME 2 DAMAGE 3 TIME COUNT 4 MAX ROUND 8 NOTE FACTORY SETTING 5 EVENT Proprietary and confidential information not to be disclosed or copied without the express permission of COIN OP INC 9 CAPCOM coin op inc STREET FIGHTER THREE WIRE COLOR SOLDER SIDE GND COMPONENT SIDE GND N 5 VDC 5 VDC WIRE COLOR 12 VDC en 2255 2522 2223 ia ans ene eae a E eee ee peo ee ees E Ue po COINLOCK2 eee ae Gee aes 5 lt 2 2 COIN COUNTER 1 COIN LOCK 1 SPEAKER 4 5 GOWN UL de CQ b o m gt SPEAKER VIDEO RED VIDEO BLUE VIDEO GROUND TEST MODE 1 PLAYER COIN 1 PLAYER START
12. X to the PC board connector may cause damage to the PC board and CD DRIVE 27 Attach Power and Data Cable to CD Drive Connect other end to SCSI combination connector on the main PCB Figure 11 28 Connect the JAMMA harness connector to the edge connector on the PC Board Figure 11 29 Attach the auxiliary cable connector to the PC Board Figure 11 3l Ifyou elect to use Q Sound Audio Amplifier connect audio cable to audio output on the PC Board Figure 11 Proprietary and confidential information not to be disclosed or copied without the express permission of CAPCOM amp COIN OP INC Carefully check connections before applying power Check the Cassette seating press firmly from top and confirm it is not loose 32 Power up the game and set the CD ROM into CD Drive See Figure 12 For detail CD Tray Door will not operate without power Game will not work without the CD ROM installed 33 After set the CD ROM the game is playable Adjust the speaker volume by turning the volume control knob clockwise to increase volume or counterclockwise to decrease volume see Reference page 34 Setall operator adjustable options by pressing the TEST switch Follow the instructions under the TEST MENU section of this manual CAPCOM coin op inc STREET FIGHTER THREE CONOP ING STREET FIGHTER THREE _ Volume Control Knob Wf To Power Supply Control Panel Coin Do
13. appear on the monitor 6 GAME DATA penc For a cabinet without a test switch 8 GAME REWRITE Push Test switch on the PC Board See Reference 9 EXIT page SELEC E 2 HOW TO SELECT AN ITEM START 1P START amp SHOT1 Use the PLAYER I JOYSTICK to move the arrow in front of the desired item and press the PLAYER 1 PUNCH Player 1 Joystick Player 1 Start LIGHT button toretum to the test menu push the PLAYER 1 START and PLAYER 2 START buttons simultaneously EEE 3 Closing the test menu a RECEN To close the test menu highlight 9 Exit and push the PLAYER 1 PUNCH LIGHT b Player 1 Shot 1 Player 1 Shot 2 Vieot Punch Light Punch Middle The test menu will always appear on the screen A after you exit the 7 CONFIGURATION MENU and B after the memory is tested from the menu 8 MEMORY CHECK 4 TEST MENU ITEM DESCRIPTIONS INPUT USED TO TEST ALL THE INPUT SWITCHES SUCH AS JOYSTICKS AND BUTTONS THE 07 CHANGES TO A 1 AS THE BUTTON IS PUSHED OR JOYSTICK IS MOVED CHECK CONNECTIONS AND SWITCHES IN CASE THE 0 DOESN T CHANGE TO A 1 WHEN DEPRESSED OR MOVED OUTPUT USED TO TEST THE COIN METER AND THE COIN LOCK SOUND SELECT A CODE OF SOUND OR VOICE WITH THE PLAYER 1 JOYSTICK PUSH THE PLAYER 1 PUNCH LIGHT BUTTON TO HEAR THE SOUND OF THE SELECTED CODE COLOR SHOWS COLOR BARS OF RED GREEN BLUE AND WHITE ADJUST RGB AND BRIGHTNESS TO OBTAIN THE OPTIMUM COLOR BA
14. ions In the GAME section you can change the play difficulty level and duration of the game 1 ACCESSING THE CONFIGURATION 7 CONFIGURATION MENU MENU SYSTEM From the TEST MENU move the arrow to 7 NT CONFIGURATION and push the PLAYER 1 PUNCH LIGHT button The screen below will be displayed A DEFAULT description of each option is explained in the table below SAVE amp EXIT SELECT 1P UP OR DOWN START 1P START amp SHOT1 SYSTEM SELECT THIS ITEM TO CHANGE SETTINGS FOR CREDITS MONITOR FLIP SOUND AND COIN DOOR CONFIGURATIONS GAME SELECT THIS ITEM TO CHANGE DIFFICULTY LEVEL DAMAGE LEVEL TIME COUNT SPEED MAXIMUM NUMBER OF ROUNDS AND EVENT TYPE DEFAULT USE THIS ITEM TO RESTORE CONFIGURATION SETTINGS TO THE ORIGINAL FACTORY VALUES PRESS THE PLAYER 1 START AND PLAYER 1 PUNCH LIGHT BUTTONS AT THE SAME TIME TO SELECT THIS OPTION USE THIS TO SAVE NEW CONFIGURATION SETTINGS AND EXIT TO THE TEST MENU THE MESSAGE SAVING NEW CONFIGURATION IN EEPROM WILL APPEAR WHILE THE NEW SETTINGS ARE BEING SAVED D DO NOT TURN POWER OFF TO THE GAME UNTIL SAVING IS COMPLETE AND THE TEST MENU REAPPEARS SAVE amp EXIT AN Wiring of the test bracket requires connections to the main jamma harness as shown in Table 1 LEAD WIRE SWITCH FUNCTION CONNECTS icc es UR ee VOLUME DOWN NOCONNECTION 1 0 A OR OR E OR F OR 1 OR 2
15. ls align over the control panel holes and press in place on the overlay refer to the drill hole template for proper placement Using a knife trim material from the center hole of the joystick decal 14 Install the control panel cover figure 1 if required Overlay Trim to size Figure 1 Overlay Installation CABINET DECAL INSTALLATION 19 Remove monitor glass and install monitor card 20 Peel offthe backing to the instruction decals and place on both the top and bottom of the monitor card See Figure 5 Also apply the cabinet decals to both sides of the cabinet MARQUEE OVERLAY MONITOR CARD CABINET DECAL INSTRUCTION DECAL BOTTOM INSTRUCTION DECAL TOP Figure 5 Cabinet Decal Installation Proprietary and confidential information not to be disclosed or copied without the express permission of CAPCOM COIN OP INC e CAPRO coin op inc Reassembly of Components 15 Notice that there are two white buttons See figure 2 The WHITE buttons are START buttons Install the PLAYER ONE button on the top left hand side of the control panel and the player two button on the top right side of the control panel 1 Player EN P 2 Player 2 a D Ta Figure 2 Start Buttons Red Green Blue Red Green Blue Red Green Blue Red Green Blue Buttons Retaining ___ Rings 2 Switches 2 CL Figure 3 Control Panel Buttons and Switches 16 Install all b
16. or Monitor Test Switch To Control Panel and Speaker Monaural Figure 11 PC Board and CD Drive cable connection CD ROM INSTALLATION 35 Press Open Close button to open the CD Tray Move four Disc Locks toward 36 Set the CD ROM Secure the CD ROM withi Disc center to secure CD ROM Locks See Figure 12 Make sure it is centered and locked in place 37 Close the CD Tray by pressing Open Close button 38 After loading CD ROM the game is ready to play CAUTION Do not remove the CD ROM from the Drive during the game It could result in break down OPEN CLOSE Button Figure 12 CD ROM Installation Proprietary and confidential information not to be disclosed or copied without the express permission of CAPCOM COIN OP INC GN coin op inc STREET FIGHTER THREE TEST MENU The test menu allows you to test various functions of the game and configure settings used in the game These items include input devices such as joysticks buttons and coin mechs output devices such as monitor speakers and meters Through the test menu you can also access the configuration menu where you can change the settings of the game 1l ACCESSING THE TEST MENU TEST MENU For a cabinet or a converted cabinet 1 INPUT with a test switch 2 SOUND E VOICE Make sure the game is on Open the coin door find the 4 COLOR location of the test switch and press Test The screen 5 DOT CROSS HATCH shown left will
17. t see Figure 7 is available through your local CAPCOM distributor part number 03 0050 When installing the test switch bracket should be mounted inside the coin door and on top of the cash box for easy access See Page 7 for wiring detail NOTE only the test switch is used for this game the volume up down switches are disabled Volume adjustments must be made through the volume control knob located on the PC board Figure 7 Test Volume Bracket 24 Ifyou are converting a cabinet that is equipped with CAPCOM Q SOUND you may use stereo audio output connect to existing Q SOUND POWER AMPLIFIER 222 COIN OP INC 25 Install the caged PCB to the control panel shelf with supplied wood screws as shown in figure 8 Wood Screw gt 98 58 Qty 4 Y Figure 8 PC Board Mounting STREET FIGHTER THREE CD DRIVE INSTALLATION 26 Install the CD DRIVE in place you can access easily Horizontal placement is recommended for stable operation See figure 9 USE ONLY supplied Pam Head Screw to mount CD DRIVE MISUSE of screw may cause mechanical damage to the unit Make sure CD DRIVE mounted horizontally and leveled PPH 8 32x1 4 Qty 8 Total Self Tapping Screw Qty 4 Total Picture shown only Right side Bracket amp Screws Figure 9 CD DRIVE Mounting PC BOARD WIRING CONNECTIONS JN WARNING Improper installation of the connector haness JAMMA CD DRIVE AU
18. uttons and retaining rings on the control panel as shown in Figure 3 Install two red buttons to the immediate right of each joystick install two green buttons to the right of the red ones and install two blue buttons to the right of the green ones 17 Install the switches on the buttons as shown in figure 3 Orient the switches so that when a button is pressed the plastic contact on the switch is depressed 18 Install the joysticks on the control panel as shown in figure 4 v160700 Figure 4 Joystick Installation PC BOARD INSTALLATION Proprietary and confidential information not to be disclosed or copied without the express permission of CAPCOM COIN OP INC STREET FIGHTER THREE CONTROL PANEL WIRING NOTE all switch wires used in this game must be wired to the normally open connection on the switches Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the normally open connector of the switch 2 Reconnect the existing jamma connectors to the control panel according to the chart in table 1 22 Connect the player 1 and the player 2 kick buttons to the auxiliary cable harness as shown in figure 6 Make the connections according to the chart in table 2 To PC Board Connector CN2 To Control Panel Button Switches Figure 6 Auxiliary Cable Harness TEST SWITCH WIRING 23 Your cabinet may already equipped test switch An optional test volume bracke
Download Pdf Manuals
Related Search