OPERATING INSTRUCTIONS FOR THE STARLIGHT CONTROL
Contents
1. Pic 3 Pic 4 73 Antenna To assure dependable operation the control unit requires an antenna connected as shown in figs 3 and 4 This antenna can be a simple copper wire with a length of 17 cm which is connected directly to terminal 17 For best range it is a good idea to use an outdoor antenna which is specifically cut for the working frequency and connected using an RG58 coaxial cable with a maximum length of 15 metres the entire antenna system must have an impedance of 50Q Term no CT ypecofconmection 1 Ground from mains power connection 2 Ground from motor connection Z gt 3 Mains power input connection phase O Z S O 4 Mains power input connection neutra O o S O 5 230 VAC output phase to be connected to terminal 8 when motors with an electro mechanical limit switch are used 6 230 VAC output neutral common connection for motors with an electro mechanical limit switch Output for raise command EA Output of common operation to be used for contacts with neutral connections or to be connected to terminal 5 when motors with an electro mechanical limit switch are used 9 Output for lower command _ _ S O 10 11 External STOP contact normally closed _ S O 12 13 External RAISE contact normally open gt Z gt 14 15 External LOWER contact normally open __ S 16 Ground pole of antenna connection Z gt Z S O Central pole of antenna connection 12. Intermediate frequency 75 KHz Local oscillator emission lt 57dBm IF intermediate frequency 500 KHz Input impedance 50Q Sensitivity signal resulting in actuation luv 22 Transmitter Voltage requirement GP23A alkaline battery 12 V 10 Max current draw 25 mA Apparent radiated power 20 to 16 dBm 10 to 20 u W Apparent radiated power of harmonics lt 54 dBm lt 4n W Carrier frequency 433 92 MHz Carrier frequency tolerance 75 KHz Bandwidth gt 25 KHz Modulation AM ASK Ambient temperature 10 to 55 C 3 Control devices Besides the capability of being controlled by one or more radio transmitters the Starlight unit can be controlled in exactly the same manner using two external normally open buttons connected to the unit by cable Furthermore a normally closed contact for example a button can be connected to the unit to obtain an emergency stop function During a movement for example raising if the opposite command for example lowering is given by pushing the relative button the movement will stop Pressing the button a second time can then start the opposing movement compared with the initial one To facilitate the testing of raising and lowering movements when the control unit is placed into service the unit is equipped with two control buttons TA and TC on the inside Also connecting or disconnecting internal bridge connection J3 as
3. OPERATING INSTRUCTIONS FOR THE STARLIGHT CONTROL UNIT CE MODEL AE0822 INDEX 1 General information 5 2 Enabling performed from the Starlight control unit Technical specifications 2 1 Starlight control unit 2 2 Transmitter Control devices 3 1 Automatic operation 3 2 Continuously actuated manual operation 4 Transmitter 5 Enabling and cancelling channels on a transmitter 5 1 Enabling performed directly on the transmitter 1 General information The Starlight control unit is a system providing remote control of motors equipped with a limit switch It can actuate motors with an electro mechanical or electronic limit switch as well as other devices with neutral control contacts Since it uses only two channels raise and lower per transmitter the Starlight unit can recognise up to 32 transmitters If centralisation is desired one transmitter can control a virtually unlimited number of control units The enabling or cancellation of channels for one or more transmitters can be carried out from the control unit or directly on the transmitter itself Since the transmitters used are compatible with the Jolly Sat system centralised configurations with mixed actuation methods can be set up if needed When the control button on a transmitter is pressed an UHF radio signal is sent The signal contains a highly reliable code composed of 66 Rolling code type digits which means that the code is changed at every transmission using
4. 2 3 5 CAMEGROUP freedominnovation info jollymotor com www jollymotor com cod 32068_ver 1 0_05 2010_EN
5. command indications invert it by changing the deviator s S1 postion See Pic 2 The Individual control with The Centralized control with 1 Raising 2 Lowering 3 Lowering 4 Raising Internal elements j VI P3 l A Pic 2 5 Enabling and cancelling channels on a transmitter NOTE transmitter or from the Starlight control unit These operations can be performed directly on the 5 1 Enabling performed directly on the transmitter First system This procedure applies only if no other transmitter has been enabled in Starlight memory 1 Open the cover on the transmitter as shown in Fig 2 2 Press button P3 on the transmitter The Starlight control unit will emit a continuous sound for 5 seconds which shows that it is entering the enabling mode 3 Within 5 seconds press the button on the transmitter for the channel to be enabled 4 The Starlight control unit will emit an intermittent sound which shows that the channel has been enabled CAMEGROUP freedominnovation info jollymotor com www jollymotor com The first channel of transmitter enabled in Starlight memory will become the master which can then be used to enable additional channels or transmitters Proceed as follows 1 Open the cover on the transmitter which has been enabled in Starlight memory master 2 Press button P3 The Starlight control unit will emit a continuous sound for 5 seconds which shows that it is e
6. an algorithm that only the receiver can recognise This code is maintained in memory even if a power failure occurs Besides receiving commands via radio the Starlight control unit can handle commands sent by a traditional keyboard over a cable The unit also features an emergency stop function controlled by a normally closed external contact Warning Never install the controller on a metal support The controller may be sensitive to external elements such as metal bodies and electromagnetic fields capable of reducing controller capacity Before installation verify the correct exchange between the controller and the motors to be driven 2 Technical specifications 2 Starlight control unit Voltage requirement 230 VAC 10 50 Hz Max output current 5 A cos 1 2 2 A cos 0 4 Nominal voltage on contacts 250 VAC 50 Hz CAMEGROUP freedominnovation info jollymotor com www jollymotor com 5 3 Cancellation performed directly on the transmitter 5 4 Cancellation performed from the Starlight control unit 6 Adjustments le Electrical connections 7 1 Connection to a gear motor with an Electro mechanical limit switch 7 2 Connection to a gear motor with an electronic limit switch or to other systems 7 3 Antenna Operating time of output contacts 1 to 90 sec adjusted on TL Usage temperature 20 to 60 C Receiver frequency 433 92 MHz Local oscillator frequency 433 42 MHz
7. described in paragraphs 3 1 and 3 2 can vary the operating logic of the control buttons cod 32068_ver 1 0_05 2010_EN _ t_ EE SSS 3 1 Automatic operation The control unit operates Homo Present when bridge connection J3 is disconnected This functioning mode operator is present and he is commanding by pushing a button on a transmitter as well as any command given by a pushing a button connected by cable The command is maintained until a new one is given or until expires the operating time selected by the TL see par 6 Movements can be stopped immediately by opening the STOP contact or by pressing the button which controls movement in the opposite 3 2 Continuously actuated manual operation When bridge connection J3 is connected continuously actuated manual operation is obtained that is all manual or radio controlled movements continue for as long as the relative control button is held down and movement stops immediately when the button is released 4 Transmitter Transmitters are directly encoded by Jolly Motor using code matrixes that are different from one another If a key is held down for more than 30 sec the transmitter is automatically deactivated External elements RED LED INDIVIDUAL CONTROL RADIO EMISSION 1 and 2 INDICATOR lt CENTRALIZED CONTRO X 3 and 4 RY s1 Note If during the first motor activation the roller tube movement is opposite to the push button
8. mand to the motor raising or lowering is automatically maintained by the control unit This time can be adjusted from 1 to 90 seconds on trimmer TL which is located in the control unit NOTE Since the operating time is read every time a movement begins adjustments made during movement will not be recognised cod 32068_ver 1 0_05 2010_EN _____ eee SS 7 Electrical connections 7 1 Connection to a gear motor with an Electro mechanical limit switch 7 2 Connection to a gear motor with an electronic limit switch or to other systems URERA LING URERATING Jz Pl Pe TL J3 Fi Pe TL TE LOO A 100 A a 29 a 7 J Wu GS aH Ye Ss a we A eS 2 S a a ae 47 7 SX t4 TC 5 m Ka TA TC E S FOO aes oo SO Qi FUS 3 194 TEST TEST FUS 3 158 TEST TEST OF RAISE MOVEMENT L OF LOWER MOVEMENT OF RAISE MOVEMENT F LOWER MOVEMENT ajeje S e jaja leje leleleje P S S S Sjele elel eljelje e 4 7 9 4115 3l4l5l6 7 8 9 lolu felis li4li5 16l17 ojoti 8 N E olo iJe2 e30v 50H D 2 es0v S0Hz cy A s M bel JEA JEA rem E7 Ea EG 1 4 i
9. mory via radio proceed as follows 1 Open the battery cover on the transmitter 2 Press key P3 inside the transmitter three times at regular intervals within a 5 second period The control unit will emit an intermittent sound 3 Within 5 seconds presses the key for the channel to be cancelled The sound made by the control unit will stop when cancellation is completed 4 Repeat steps 1 2 and 3 for each channel to be cancelled 5 4 Cancellation performed from the Starlight control unit To cancel a channel proceed as follows 1 Hold down key P2 After 1 second the Starlight control unit will emit an intermittent sound Now release P2 2 Press the button for the channel to be cancelled The control unit will emit a continuous sound which shows that the channel has been cancelled 3 Repeat steps 1 and 2 for each channel to be cancelled To delete all the channels stored in memory proceed as follows 1 Hold down key P2 for at least 1 second and then release it control unit will emit a slowly intermittent sound 2 Immediately within half a second press P2 again and hold it down for at least 10 seconds The slowly intermittent sound will now change to a rapidly intermittent sound and then to a continuous sound Release P2 The memory in the control unit is now completely empty The 6 Adjustments The only adjustment required is setting the operating time of the output contacts that is the amount of time a com
10. ntering the enabling mode 3 Within 5 seconds presses the button for a channel which has already been enabled 4 The sound emitted by the control unit will be interrupted for 1 second and will then resume for 5 more seconds 5 Within this last 5 seconds select the new channel to be enabled 6 The Starlight control unit will emit an intermittent sound which shows that the channel has been enabled 7 Repeat steps 2 through 6 to enable additional channels 5 2 Enabling performed from the Starlight control unit It is a good idea to delete the entire contents of memory before each initial installation see chap 5 4 1 Hold down button P1 After 1 second the Starlight control unit will emit a continuous sound 2 Press the button for the channel to be enabled The Starlight control unit will emit an intermittent sound which shows that the channel has been enabled 3 Repeat steps 1 and 2 for each channel to be enabled on the control unit Note If the enabling operation is not successful a Make sure that the channel has not been previously enabled b Make sure that the memory in the control unit is not full 64 channels max To check for full memory switch off the power to the control unit and then switch it back on The unit will emit an intermittent sound for 3 seconds at start up if the memory is full 5 3 Cancellation performed directly on the transmitter To cancel a transmitter channel from control unit me
Download Pdf Manuals
Related Search