USER'S MANUAL “9 BEDIENUNGSANLEITUNG CQI I lao MANUEL
Contents
1. e TILT 270 High speed strobe gt 30 Hz e Stand alone modes Auto Run Sound Control Show e Power consumption 100 W e Long life LED with especially long service life CONNECTIONS CONTROL PANEL AND INDICATORS ae DMX IN DMX OUT POWER IN FUSE power socket with fuse holder IMPORTANT INFORMATION Replace the fuse only with a fuse of the same type and rating If the fuse blows repeatedly please contact an authorised service centre DMX N 3 pole XLR input socket for connection of a DMX controller e g DMX mixer pmx out 3 pole XLR output socket for looping through the DMX control signal LED DISPLAY Display of the operating modes and additional system settings CONTROL BUTTONS 4 easily accessible control buttons let you configure the system colours of mo z CLHRGB25W r 25W LED MOVING HEAD WITH 7 GOBOS OPERATION DEUTSCH ESPANOL z STARTUP Once you have connected the Cameo LED Moving Head to the power mains the motor reset process starts automatically After approx 20 seconds the motors are realigned and the unit is operational Focus the projection by turning the objective ring SELECTING THE DMX START ADDRESS Press the MODE button and then use the UP and DOWN buttons to select the DMX Start Address mode Addr will appear in the display Now press ENTER and use2. Adam Hall LD Systems Defender Palmer and Cameo brands It applies to all products distributed by Adam Hall This warranty declaration does not affect the statutory warranty claims against the manufacturer but expands them with additional warranty claims vis a vis Adam Hall Adam Hall warrants that the Adam Hall product that you have purchased from Adam Hall or from an Adam Hall authorized reseller is free from defects in materials or workmanship under normal use for a period of 2 or 5 years please inquire on a product by product basis from the date of purchase The warranty period begins on the date on which the product was purchased proof of which must be produced through presentation of the invoice or the delivery note with the date of purchase in the event of a warranty claim Should products of the brands named above be in need of repair within the limited warranty period you are entitled to warranty service according to the terms and conditions stated here HOSLNAG During the Limited Warranty Period Adam Hall will repair or replace the defective component parts or the product In the event of repair or replacement during the Limited Warranty Period the replaced original parts and or pro ducts become property of Adam Hall In the unlikely event that the product which you purchased has a recurring failure Adam Hall has the right at its discretion to replace the defective product with another product provided that the new pr
3. lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock gt The exclamation mark within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions CAUTION HIGH VOLUME LEVELS WITH AUDIO PRODUCTS This equipment is intended for professional use Therefore commercial use of this equipment is subject to the respectively applicable national accident prevention rules and regulations As a manufacturer Adam Hall is obligated to notify you formally about the existence of potential health risks Hearing damage due to high volume and prolonged exposure When in use this product is capable of producing high sound pressure levels SPL that can lead to irreversible hearing damage in performers employees and audience members For this reason avoid prolonged exposure to volumes in excess of 90 dB CAUTION IMPORTANT INFORMATION ABOUT LIGHTING PRODUCTS 1 Do not look into the beam from a distance of less than 40 cm 2 Do not stare into the beam for extended periods at short to medium distances 3 Do not view the beam directly with optical instruments such as magnifiers 4 Under some circumstances stroboscopic effects may trigger epileptic seizures in sensitive individuals For this
4. of heat Make certain that the equipment is always installed so that is cooled sufficiently and cannot overheat 9 Never place sources of ignition e g burning candles on the equipment 10 Ventilation slits must not be blocked 11 Do not use this equipment in the immediate vicinity of water does not apply to special outdoor equipment in this case observe the special instructions noted below Do not expose this equipment to flammable materials fluids or gases 12 Make certain that dripping or splashed water cannot enter the equipment Do not place containers filled with liquids such as vases or drinking vessels on the equipment 13 Make certain that objects cannot fall into the device 14 Use this equipment only with the accessories recommended and intended by the manufacturer 15 Do not open or modify this equipment 16 After connecting the equipment check all cables in order to prevent damage or accidents e g due to tripping hazards 17 During transport make certain that the equipment cannot fall down and possibly cause property damage and personal injuries 18 If your equipment is no longer functioning properly if fluids or objects have gotten inside the equipment if it has been damaged in anot her way switch it off immediately and unplug it from the mains outlet if it is a powered device This equipment may only be repaired by authorized qualified personnel 19 Clean the equipment using a dry cloth 20
5. reason persons who suffer from epilepsy should always avoid places where strobe lights are used SIVONVYS HOSLNAG BIS ARE gt p INTRODUCTION DEUTSCH ESPANOL LED MOVING HEAD 25 W CLMHRGB25W The Cameo CLMHRGB25W is a compact lightweight moving head with a high efficiency low power consumption 25 watt white LED featuring XLR connectors for DMX input and output an IEC power socket and fan cooling The light can be used open or with one of the seven 21 mm gobos and offers a palette of eight vivid colours plus white With 540 pan and 270 tilt capability augmented by dimmer and shutter functions and high speed stroboscopic effects it is possible to realise a very wide range of lighting applications In addition to the DMX modes with 6 or 11 channels the CLMHRGB25W can also be operated as a stand alone unit with program or music control The easy to read LED display and the Mode Enter Value Up and Value Down ensure convenient control of the integral lighting programs CONTROL FUNCTIONS 6 and 11 channel DMX control Separate control of pan and tilt Separate control of gobo and colour wheel Master slave mode e Stand alone mode FEATURES Colour spectrum 8 colours white e Bright 25 W LED e Number of gobos 7 open DMX mode 6 channel 11 channel DMX functions PAN TILT Colour Wheel Gobo Wheel Shutter Dimmer Program PAN 360 540
6. z z DMX CONTROL 11 CHANNEL MODE 000 255 Dimmer 0 100 CHANNEL no function Blackout during pan tilt movement Blackout during gobo colour wheel rotation Colour wheel motor and gobo wheel motor reset Reset all motors Program 1 Program 2 CH9 hou Program 3 HOSLNAG 136 152 Program 4 153 169 Program 5 170 186 Program 6 187 203 Program 7 204 220 Program 8 Pan fine contro Tilt fine control TONVdS3 gt SPECIFICATIONS ESPANOL FRANCAIS DEUTSCH z z Product type Colour spectrum Number of LEDs LED type Number of gobos Gobo size DMX input DMX output DMX mode DMX functions PAN movement TILT movement High speed stroboscope Stand alone modes Controls Indicators Operating voltage Power consumption Power connector Housing material Housing colour Cooling system Dimensions Weight LED moving light Moving head 8 colours white 7 open 1mm XLR 3 pin male XLR 3 pin female 6 channel 11 channel PAN TILT program colour wheel shutter dimmer gobo wheel 360 540 adjustable 270 gt 30 Hz Auto Run Sound Control Show Value Up Mode Enter Value Down LED display 230 V AC 50 Hz 100 W IEC power socket male Metal ABS plastic lack 8000 Ix 1m 230 x 275 x 320 mm 7 kg MANUFACTURER S DECLARATIONS MANUFACTURER S WARRANTY This warranty covers the
7. 160 179 Gobo 5 shake speed 180 199 Gobo 6 shake speed 200 219 Gobo 7 shake speed 220 255 Gobo wheel rotation speed ESPANOL FRANCAIS DEUTSCH CH1 CH2 CH3 H4 DMX CONTROL 6 CHANNEL MODE 000 127 manual gobo rotation Gobo 128 191 Gobo rotation right speed fast slow rotation 192 255 Gobo rotation left speed slow fast 000 009 closed 020 127 Stroboscope effect 1 speed slow fast Shutter 138 201 Stroboscope effect 2 speed slow fast HOSLNAG 11 CHANNEL MODE 000 255 Pan movement 360 540 000 255 Tilt movement 270 CH3 Pan tilt 000 255 Speed of the pan and tilt movement from fast to slow movement 098 111 TlONVdS3 128 191 Rainbow direction of rotation forwards speed fast slow 192 255 Rainbow direction of rotation forwards speed fast slow DMX CONTROL 11 CHANNEL MODE wmm D Lu 140 159 Gobo 4 shake speed FRANCAIS 160 179 Gobo 5 shake speed 180 199 Gobo 6 shake speed 200 219 Gobo 7 shake speed 220 255 Gobo wheel rotation speed 127 manual gobo rotation nobo 191 Gobo rotation right speed fast slow rotation 192 255 255 Gobo rotation left speed slow fast 020 127 Stroboscope effect 1 speed slow fast Shutter 138 201 Stroboscope effect 2 speed slow fast ESPANOL
8. Comply with all applicable disposal laws in your country During disposal of packaging please separate plastic and paper cardboard 21 Plastic bags must be kept out of reach of children DEUTSCH ESPANOL FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS 22 CAUTION If the power cord of the device is equipped with an earthing contact then it must be connected to an outlet with a protective ground Never deactivate the protective ground of a power cord 23 If the equipment has been exposed to strong fluctuations in temperature for example after transport do not switch it on immediately Moisture and condensation could damage the equipment Do not switch on the equipment until it has reached room temperature 24 Before connecting the equipment to the power outlet first verify that the mains voltage and frequency match the values specified on the equipment If the equipment has a voltage selection switch connect the equipment to the power outlet only if the equipment values and the mains power values match If the included power cord or power adapter does not fit in your wall outlet contact your electrician 25 Do not step on the power cord Make certain that the power cable does not become kinked especially at the mains outlet and or power adapter and the equipment connector 26 When connecting the equipment make certain that the power cord or power adapter is always freely accessible Always disconnect the equipment from the
9. N or DOWN to select Reverse Off OFF Confirm with ENTER L IY Lt 2 Ln L Ca L 1 00 1 mw 2 Ca m OPERATION SIVONVYS HOS LNAG lONVdS3 I gt OPERATION DEUTSCH ESPANOL ITALIANO REVERSE TILT This function makes it possible to reverse the TILT motion Press the MODE button and then use the UP and DOWN buttons to select the Reverse Tilt function r t I L will appear the display Now press the ENTER button and use the UP button to select Reverse On ON or DOWN to select Reverse Off OFF Confirm with ENTER REVERSE DISPLAY This function makes it possible to rotate the characters in the display by 180 Press the MODE button and then use the UP and DOWN buttons to select the Reverse Display function r d I S will appear in the display Now press the ENTER button and use the UP button to select Reverse On ON or DOWN to select Reverse Off OFF Confirm with ENTER PAN ROTATION 360 540 This function can be used to set the maximum pan rotation of the light to either 360 or 540 Press the MODE button Addr will appear in the display and then use the UP and DOWN buttons to select the Pan Rotation function d E g r will appear in the display Now press the ENTER button and use the UP but
10. USER S MANUAL BEDIENUNGSANLEITUNG of CO MANUEL D UTILISATION SRE EA MANUAL DE USUARIO INSTRUKCJA OBS UGI MANUALE D USO LED MOVING HEAD 25W CLMHRGB25W DEUTSCH ESPANOL Thank you for choosing Cameo Lights We have designed this product to give you reliable operation over many years Please take a few moments to read these instructions carefully as we want you to enjoy your new Cameo Lights products quickly and to the fullest Further information about Cameo Lights check our website WWW CAMEOLIGHT COM LED MOVING HEAD 25W CLMHRGB25W e SS YA O ONVITVLI DIS 10d BIS ARE SIVONVYS HOSLNAG PREVENTIVE MEASURES 1 Please read these instructions carefully 2 Keep all information and instructions in a safe place 3 Follow the instructions 4 Observe all safety warnings Never remove safety warnings or other information from the equipment 5 Use the equipment only in the intended manner and for the intended purpose 6 Use only sufficiently stable and compatible stands and or mounts for fixed installations Make certain that wall mounts are properly installed and secured Make certain that the equipment is installed securely and cannot fall down 7 During installation observ e the applicable safety regulations for your country 8 Never install and operate the equipment near radiators heat registers ovens or other sources
11. chnical data and the functional product characteristics can be subject to modifications The photocopying the translation and all other forms of copying of fragments or of the integrlity of this user s manual is prohibited
12. ess the MODE button Addr will appear in the display and then use the UP and DOWN buttons to select the Auto mode AUTO will appear in the display Now press the ENTER button and use the UP button to select the Master mode MAST or DOWN to select the Stand alone mode ALON and confirm with ENTER The display will now read AU M for Master mode AU A for Stand alone mode In Master mode additional lights of the same type can be used as slave units on the master unit Select the DMX mode for the slave unit and set the DMX start address to 001 Using a DMX cable connect the slave unit s to the master unit master unit DMX OUT slave unit DMX IN Now the slave unit follows the master unit In stand alone mode the light operates independently of any other units connected to it SHOW MODE Press the MODE button Addr will appear in the display and then use the UP and DOWN buttons to select the Show mode SHOW will appear in the display Now press the ENTER button and use the UP button to select Show 1 SH 1 or DOWN to select Show 2 SH 2 and confirm with ENTER Show 1 and Show 2 contain pre programmed sequences of motion and colour and gobo changes REVERSE PAN This function makes it possible to reverse the PAN motion Press the MODE button and then use the UP and DOWN buttons to select the Reverse Pan function r PAN will appear in the display Now press the ENTER button and use the UP button to select Reverse On O
13. ocess begins and after approx 20 seconds the motors are recalibrated and the unit is operational FACTORY DEFAULTS You can use this function to reset the unit to the factory default settings Press the MODE button and then use the UP and DOWN buttons to select LOAd Now press the ENTER button All settings microphone sensitivity reverse display have now been reset to the factory defaults The unit is immediately operational again C1 mu Ce NOTE If one of the 4 buttons is not pushed the LED display switches off automatically after approx 70 seconds As soon as one of the four buttons is pressed the display switches on again automatically In DMX mode the display blinks as soon as the light no longer receives a DMX signal gt DMX CONTROL 6 CHANNEL MODE Pan movement 360 540 000 255 Tilt movement 270 CHANNEL on 02 000 013 White 014 027 Yellow 028 041 Magenta 042 055 056 069 Violet 070 083 Cyan 084 097 Bright green 098 111 Amber 112 127 Dark red 128 191 Rainbow direction of rotation forwards speed fast slow 192 255 Rainbow direction of rotation forwards speed fast slow 000 009 010 019 Gobo 1 020 029 Gobo 2 030 039 Gobo 3 040 049 Gobo 4 050 059 Gobo 5 060 069 Gobo 6 070 079 080 099 Gobo 1 shake speed 100 119 Gobo 2 shake speed 120 139 Gobo 3 shake speed 140 159 Gobo 4 shake speed
14. oduct is at least equi valent to the product being replaced with regard to the technical specifications Adam Hall does not warrant that the operation of this product will be uninterrupted or error free Adam Hall is not responsible for damage that occurs as a result of your failure to follow the instructions included with the Adam Hall branded product The manufacturer s warranty does not cover expendable parts e g rechargeable batteries products from which the serial number has been removed or with a serial number that has been damaged as a result of an accident damage due to improper use user error or other external reasons damage to devices operated outside the usage parameters stated in the documentation included with the product damage due to the use of replacement parts not manufactured sold or recommended by Adam Hall damage due to modification or servicing by anyone other than Adam Hall These terms and conditions constitute the complete and exclusive warranty agreement between you and Adam Hall regarding the Adam Hall branded product you have purchased BIS ARE gt p MANUFACTURER S DECLARATIONS LIMITATION OF LIABILITY If your Adam Hall branded hardware product fails to work as warranted above your sole and exclusive remedy shall be repair or replacement Adam Halls maximum liability under this limited warranty is expressly limited to the lesser of the price you have paid for the product
15. or the cost of repair or replacement of any components that malfunction under conditions of normal use Adam Hall is not liable for any damages caused by the product or the failure of the product including any lost profits or savings or special incidental or consequential damages Adam Hall is not liable for any claim made by a third party or made by you for a third party DEUTSCH This limitation of liability applies whether damages are sought or claims are made under this Limited Warranty or as a tort claim including negligence and strict product liability a contract claim or any other claim and cannot be rescinded or changed by anyone This limitation of liability will be effective even if you have advised Adam Hall or an authorized representative of Adam Hall of the possibility of any such damages but not however in the event of claims for damages in connection with personal injuries This manufacturer s warranty grants you specific rights depending on jurisdiction nation or state you may be be entitled to additional claims You are advised to consult applicable state or national laws for a full determina tion of your rights REQUESTING WARRANTY SERVICE To request warranty service for the product contact Adam Hall or the Adam Hall authorized reseller from which you purchased the product EC DECLARATION OF CONFORMITY The equipment marketed by Adam Hall complies where applicable with the essential requirements and
16. other relevant specifications of Directives 1999 5 EC R amp TTE 2004 108 EC EMC und 2006 95 EC LVD Additional information can be found at www adamhall com ESPANOL e z z MANUFACTURER S DECLARATIONS PROPER DISPOSAL OF THIS PRODUCT Valid the European Union and other European countries with waste separation lt This symbol on the product or the documents accompanying the product indicates that this appliance may not be treated as household waste This is to avoid environmental damage or personal injury due to uncontrolled waste disposal Please dispose of this product separately from other waste and have it recycled to promote sustainable economic activity Household users should contact either the retailer where they purchased this product or their local government office for details on where and how they can recycle this item in an environmentally friendly manner Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal ENVIRONMENTAL PROTECTION AND ENERGY CONSERVATION Energy conservation is an active contribution to environmental protection Please turn off all unneeded electrical devices To prevent unneeded devices from consuming power in standby mode disconnect the mains plug TlONVdS3 SIVONVYS HOSLNAG gt p Z Adam Hall GmbH all rights reserved The te
17. power supply if the equipment is not in use or if you want to clean the equipment Always unplug the power cord and power adapter from the power outlet at the plug or adapter and not by pulling on the cord Never touch the power cord and power adapter with wet hands 27 Whenever possible avoid switching the equipment on and off in quick succession because otherwise this can shorten the useful life of the equipment 28 IMPORTANT INFORMATION Replace fuses only with fuses of the same type and rating If a fuse blows repea tedly please contact an authorised service centre 29 To disconnect the equipment from the power mains completely unplug the power cord or power adapter from the power outlet 30 If your device is equipped with a Volex power connector the mating Volex equipment connector must be unlocked before it can be removed However this also means that the equipment can slide and fall down if the power cable is pulled which can lead to personal injuries and or other damage For this reason always be careful when laying cables 31 Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse CAUTION RISK OF ELECTRIC SHOCK DONOTOPEN CAUTION Never remove the cover because otherwise there may be a risk of electric shock There are no user serviceable parts inside Have repairs carried out only by qualified service personnel The
18. the UP and DOWN buttons to select the desired DMX start address A001 A512 Confirm with ENTER MUSIC CONTROL Press the MODE button Addr will appear in the display and then use the UP and DOWN buttons to select the Music Control mode SOUN will appear in the display Now press the ENTER button and use the UP button to select the Master mode MAST or DOWN to select the Stand alone mode ALON and confirm with ENTER The display will now read 50 for Master mode or SO A for Stand alone mode In Master mode additional lights of the same type can be used as slave units on the master unit Select the DMX mode for the slave unit and set the DMX start address to 001 Using a DMX cable connect the slave unit s to the master unit master unit DMX OUT slave unit DMX IN Now the slave unit follows the master unit In stand alone mode the light operates independently of any other units connected to it MICROPHONE SENSITIVITY Press the MODE button Addr will appear in the display and then use the UP and DOWN buttons to select the menu item for setting the microphone sensiti vity MIC will appear in the display Press ENTER and use the UP and DOWN buttons to select the desired sensitivity M 00 to M 99 Confirm with ENTER mu LP cJ ru d o un m E LI 7171 d AUTO MODE Pr
19. ton to select 360 360 or DOWN to select 540 540 and confirm with ENTER a C1 3 Co m T1 3 Tx 3 Co TH m 7 Lot Ly Ca OPERATION SELECTING DMX MODE p LI r1 r1 Use this function to set the light to either the 6 channel or 11 channel mode LI LI Press the MODE button Addr will appear in the display and then use the UP and DOWN buttons to select the DMK mode selection function CHMO will appear in the display Now press the ENTER button and use the UP but L Lf ton to select the 6 channel mode 06CH or DOWN to select the 11 channel JI mode 11CH and confirm with ENTER m END Ly e SIS FIXTURE TIME Using this function the fixture time can be displayed Press the MODE button and then use the UP and DOWN buttons to select the fixture time display 111 appears in the display Now press the ENTER button The display shows the number of hours for which the unit has m 5 already been in operation 52 Use this function to start the motor reset process tH Press the MODE button and then use the UP and DOWN buttons to select ep gt m the reset function r E s t appears in the display Now press the ENTER L m button The rest pr
Download Pdf Manuals
Related Search