Home

Domestic owners manual 2007

1. Optional less subwoofer ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 2 0 1 0 HP 2 0 1 0 HP Pump 2 peak Continuous HP 4 0 2 0 HP 4 0 2 0 HP 4 0 2 0 HP 4 0 2 0 HP Air Bubbler 2 Pump 3 peak Continuous HP 3 4 1 5 HP 1 5 HP Electronics Electrical Can Gecko XM Series Gecko M Series Voltage 240 240 Amperage 50 32 3x 16 16 1 1 Heater 6H 4 0 KW 3 0 KW Operation System Main Spa Side Control 7 600 Series Gecko Gecko GE Deluxe Secondary Spa Side Control 8 Optional 100 Series Gecko Optional Not every jet is referenced Each type of jet is noted for ease of identification Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice 23 SPA INSTALLATION INSTALLATION GUIDELINES THE LOCATION OF YOUR SPA IS AN IMPORTANT FACTOR IN GUARANTEEING YOUR MAXIMUM SPA ENJOYMENT GENERALLY MOST SPAS ARE INSTALLED OUTDOORS WITH NO CONCERNS REGARDING MOISTURE ACCUMULATION WATER SPILL OVER ETC WHICH ARE CONSIDERATIONS FOR THOSE LOCATED INSIDE OUTDOOR INSTALLATION CONSIDERATIONS 1 LOCAL ELECTRICAL AND PLUMBING CODES
2. 2 CONSIDER LOCAL CODES PERTAINING TO FENCING ENCLOSURES WALLS ELECTRICAL AND PLUMBING YOU WILL NEED TO ENSURE THAT YOUR SPA IS AN ADEQUATE DISTANCE FROM POWER LINES BOTH ABOVE GROUND AND UNDERGROUND YOUR SPA WILL ALSO NEED TO BE CHILDPROOFED 3 VIEW FROM HOUSE FOR AESTHETICS AND SUPERVISORY NEEDS 4 DISTANCE FROM HOUSE FOR WINTERTIME SOAKING 5 NIGHTTIME LIGHTING 6 LOCATE THE SPA WITH AN AWARENESS TO SUNLIGHT EXPOSURE VIEWS ACCESS PROPERTY LINES LIGHTING WIND DIRECTION SHIELDING SEPTIC TANKS PLANTS TREES CHEMICALS IN THE SPA WATER SPLASHED FROM YOUR SPA MAY DAMAGE NEARBY PLANT LIFE 7 CONSIDER THE LOCATION OF THE NEAREST BATHROOM 8 IF YOUR SPA IS TO BE LOCATED ON A SECOND STORY BE POSITIVE SUPPORT IS ADEQUATE CALL YOUR BUILDER 9 AREA FOR PLACEMENT OF SUPPORT EQUIPMENT WHERE ADEQUATE SPACE WILL BE NEEDED TO GAIN ACCESS TO COMPONENTS FOR MAINTENANCE AND GENERAL SERVICING 10 BE SURE TO NOTE ANY OTHER CONSIDERATIONS SUCH AS AESTHETICS OR PRIVACY CONCERNS THAT MAY AFFECT THE SAFETY OR ENJOYMENT OF USING THE SPA 11 PROVIDE ADEQUATE DRAINAGE AWAY FROM THE EQUIPMENT AND ADEQUATE ELEVATION TO ALLOW DRAINING BY SIPHON IF SHOULD BE REQUIRED 12 LOCATION OF ELECTRICAL SUPPLY 120 240 VOLT SYSTEMS REQUIRE HARD WIRE INSTALLED FROM THE ELECTRICAL SOURCE TO THE SPA SUPPORT PACK TERMINAL ALL EQUIPMENT MUST BE GROUND FAULT CIRCUIT PROTECTED AT THE POWER SOURCE ALL ELECTRICAL WIRING OF THE SPA SUPPORT EQUIPMEN
3. INDIVIDUALS WITH INFECTIONS AND OPEN SORES OR WOUNDS SHOULD NOT USE THE SPA BACTERIA THRIVE IN WARM AND HOT WATER ALWAYS KEEP YOUR SPA DISINFECTED AND MAINTAIN THE PROPER CHEMICAL BALANCE SHOWER BEFORE AND AFTER USING THE SPA THIS WILL REMOVE ANY DEODORANT PERSPIRATION OR BODY OILS THAT COULD CONTAMINATE THE WATER SHOWERING AFTER WILL REMOVE ANY RESIDUAL CHEMICALS AND ANY BACTERIA THAT MAY HAVE BEEN IN THE SPA SAFETY INSTRUCTIONS DO NOT USE THE SPA IMMEDIATELY AFTER STRENUOUS EXERCISE IF YOU FEEL PAIN OR DIZZINESS AT ANY TIME WHILE USING THE SPA DISCONTINUE USE AND CONTACT A PHYSICIAN WARNING TO REDUCE THE RISK OF INJURY IT IS ESPECIALLY IMPORTANT FOR PERSONS OVER THE AGE OF 35 OR PERSONS WITH PRE EXISTING HEALTH PROBLEMS SUCH AS OBESITY HEART DISEASE HIGH BLOOD PRESSURE CIRCULATORY PROBLEMS OR DIABETES TO CONSULT THEIR PHYSICIAN BEFORE USING THE SPA THE SPA JETS PRODUCE A STREAM OF WATER WITH RELATIVELY HIGH PRESSURE PROLONGED EXPOSURE OF A LOCALIZED AREA OF THE BODY MAY CAUSE BRUISES TO THE SKIN NEVER INSERT ANY OBJECT INTO ANY OPENING DO NOT USE BREAKABLE CONTAINERS IN OR NEAR THE SPA WARNING ELECTRICAL CONSIDERATIONS FOR CONTROLS OTHER THAN UNDERWATER LIGHTING CIRCUITS GROUND FAULT CIRCUIT INTERRUPTER MUST BE PROVIDED IF THIS DEVICE IS USED TO CONTROL AN UNDERWATER LIGHTING FIXTURE THE CONDUCTORS ON THE LOAD SIDE ON THE GROUND FAULT CIRCUIT INTERRUPTER SHALL NOT OCCUPY CONDUIT BOXE
4. key to change setting 01 00 12 00 AM PM Program key Use Program key to display time or enter Programming menu by pressing and holding key In Programming mode the following parameters can be set time filter cycle s start time duration fre quency and the choice of temperature display units BEBE Setting filter cycle duration Press Ok key a third time The display will show Fdxx with xx representing the duration in hours Use or key to change setting 0 12 hours 33 OPERATION SYSTEMS IN K 600 SERIES CONTROL CENTER LX SERIES SPAS 8 Filter cycle frequency Press Ok key a fourth time The display will show FFxx with xx representing the number of filter cycles per day up to 4 Use or key to change setting Setting temperature unit Water temperature can be displayed in either Fahrenheit F or Celsius Press Ok key a fifth time The display will show either F or C Use or key to change setting Press Ok key a last time to go back to nor mal mode Smart Winter Mode In a regulation cycle the system first generates Our Smart Winter Mode protects your system from the cold by turning pumps on several times a day to prevent water from freezing in pipes After verifying pump activation and Cooldown While performing these tasks the heater is not allowed to turn
5. 1 When this feature is activated it allows to stop all pumps at the same time by a simple click of a button Use Standby key to pause all pumps Progress bar will display the remaining time before the system automatically exits Standby mode user can also exit Standby mode at any time by pressing again on Standby key Pump 2 key 2 Press Pump 2 key to turn Pump 2 on at high speed Press a second time to turn pump off A built in timer automatically turns pump off after 20 minutes unless pump has been manually deactivated first 31 IN K 600 SERIES CONTROL CENTER LX SERIES SPAS icon In order to warn the user the spa light will flash for a few seconds before the exit of Standby mode and restart the pumps The Stby message is also displayed during Standby mode Pump will stay turned on if there is a request for more heat Pump 3 Press Pump 3 key to turn Pump 3 on at high speed Press a second time to turn pump off A built in timer automatically turns pump off after 20 minutes unless pump has been manually deactivated first Plus TT Pumplkev 1 Press Pump 1 key to turn Pump on at low speed Press a second time to turn pump at high speed Press a third time to turn pump off A built in timer automatically turns pump off after 20 minutes unless pump has been manually deactivated first Blowerkev Press Bl
6. Ozone Water Purification oz Optional ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 2 0 1 0 HP 2 0 1 0 HP Pump 2 peak Continuous HP 2 6 0 3 0 HP 6 0 3 0 HP Electronics Electrical Can 6 Gecko XM Series Gecko M Series Voltage 240 240 Amperage 50 1 x 16 1 x 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Spa Side Control 7 Gecko 400 Series Gecko GE Deluxe Secondary Spa Side Control 8 N A N A pas Not every jet is referenced Each type of jet is noted for ease of identification Note location of audio components prior to install Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice 15 DOMESTIC SE SERIES SPECIFICATIONS VANCOUVER SPA MODEL GENERAL rev 3 07 Seating Capacity 7 Shell Material Acrylic Dimensions Domestic 79 677 oct x 36 37 Dimensions Export 201 cm oct x 92 cm Water Capacity 520 Gallons 1 968 liters Dry Weight 575 Ibs 260 kg Skirt Material Permawood or Cedar Water Flow 187 Gallons per Minute WATER SYSTEM photo ref Water Treatment System Ozone ready Filter 25 sq ft Slide Valves 2 Mega Swi
7. 2 0 HP Electronics Electrical Can 6 Gecko XM Series Gecko M Series Voltage 240 240 Amperage 40 1 x 16 1 x 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Main Spa Side Control T Gecko 400 Control Gecko GE Deluxe Secondary Spa Side Control 8 N A N A Not every jet is referenced Each type of jet is noted for ease of identification Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice DOMESTIC SE SERIES SPECIFICATIONS BOULDER SPA MODEL GENERAL rev 3 07 Seating Capacity 6 Shell Material Acrylic Dimensions Domestic 81 679 sq x 35 27117 Dimensions Export 206 cm sq X 89 cm sq Water Capacity 375 Gallons 1 420 liters Dry Weight 665 Ibs 302 kg Skirt Material Permawood or Cedar Water Flow 428 Gallons per Minute WATER SYSTEM photo ref Water Treatment System Ozone Ready Filter 25 sq ft Side Valves 4 Mega Swirl Jet 3 Large Euro Jet w Eyeball 59 Mega ssage Jet Ozone Jet Multissage Jet Diverter Valves Safety Suction Mini Skimmer Air Control Spa Light Drain Valve lt S 1 SPECIAL FEATURES Spa Pillows 3 Motion Glow Light
8. TEMPERATURES TO 100 F 38 C BEFORE ENTERING A SPA THE USER SHOULD MEASURE THE WATER TEMPERATURE WITH AN ACCURATE THERMOMETER SINCE THE TOLERANCE OF WATER TEMPERATURE REGULATING DEVICES MAY VARY AS MUCH AS 5 F 3 C THE USE OF ALCOHOL DRUGS OR MEDICATION BEFORE OR DURING SPA USE MAY LEAD TO UNCONSICIOUSNESS WITH THE POSSIBILITY OF DROWNING PERSONS SUFFERING FROM OBESITY OR WITH A MEDICAL HISTORY OF HEART DISEASE LOW OR HIGH BLOOD PRESSURE CIRCULATIORY SYSTEM PROBLEMS OR DIABETES SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA PERSONS USING MEDICATION SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA SINCE SOME MEDICATION MAY INDUCE DROWSINESS WHILE OTHER MEDICATION MAY AFFECT HEART RATE BLOOD PRESSURE AND CIRCULATION ENTER AND LEAVE SPA SLOWLY AND WITH CAUTION SURFACES AROUND SPA WILL BE WET AND SLIPPERY WARNING 1 NEVER USE THE SPA ALONE 2 DO NOT BRING ANY OBJECT INTO THE SPA THAT COULD DAMAGE THE SPA SHELL 3 DO NOT SIT ON SPA COVER OR PLACE OBJECTS ON IT IT IS NOT DESIGNED TO SUPPORT WEIGHT 4 REMOVE ANY WATER OR DEBRIS THAT MAY COLLECT ON THE SPA COVER 5 KEEP ALL CHEMICALS AWAY FROM CHILDREN AND PETS 6 THE PH AND CHEMICAL BALANCE OF THE WATER MUST BE MAINTAINED AS EXPLAINED IN THIS MANUAL FAILURE TO DO SO MAY CAUSE INJURY TO USERS OR DAMAGE TO THE SPA AND WILL VOID YOUR WARRANTY WARNING HEALTH CONSIDERATIONS THE USE OF ALCOHOL DRUGS OR MEDICATION CAN GREATLY INCREASE THE RISK OF FATAL HYPERTHERMIA
9. DOMESTIC SE SERIES SPECIFICATIONS DENALI SPA MODEL GENERAL rev 3 07 Seating Capacity 8 Shell Material Acrylic Dimensions Domestic 81 6 9 sq x 38 3 27 Dimensions Export 206 cm sq x 97 cm sq Water Capacity 425 Gallons 1 609 liters Dry Weight 645 Ibs 293 kg Skirt Material Permawood or Cedar Water Flow 428 Gallons per Minute WATER SYSTEM photo ref Water Treatment System Ozone ready Filter 25 sq ft Slide Valves 4 Mega Swirl Jet 6 AN o Large Euro Jet w Eyeball Mega ssage Jet Multi ssage Jet Ozone Jet Diverter Valves Safety Suction Mini Skimmer Air Control Spa Light Drain Valve ale tale lt o s Q m gt RTE rO C O SPECIAL FEATURES Spa Pillows 2 Motion Glow Light Optional Stainless Steel Jetting Optional Waterfall Jet WF Optional Waterfall Control Valve Optional SoundWave Audio Optional Ozone Water Purification oz Optional ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 2 0 1 0 HP 2 0 1 0 HP Pump 2 peak Continuous HP 2 6 0 3 0 HP 6 0 3 0 HP Electronics Electrical Can 6 Gecko XM Series Gecko M Series Voltage 240 240 Amperage 50 1 x 16 1 x 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Spa Side Control 7 G
10. Optional 100 Series Gecko Optional Not every jet is referenced Each type of jet is noted for ease of identification Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice 17 PDC DOMESTIC LX SERIES SPECIFICATIONS ARUBA SPA MODEL GENERAL rev 3 07 Seating Capacity 5 Shell Material Acrylic Dimensions Domestic 86 7 2 sq x 36 3 Dimensions Export 218 cm sq 92 cm Water Capacity 375 Gallons 1 420 liters Dry Weight 670 158 304 kg Skirt Material Permawood or Cedar Water Flow 510 Gallons per Minute WATER SYSTEM photo ref Water Treatment System OZ Ozonator Filter 25 sq ft Slide Valves 6 Mega Swirl Jet A 3 Large Euro Jet w Eyeball E 26 Mega ssage Jet G 10 Ozone Jet 2 Multi ssage Jet P 3 Aromatherapy 1 Foot Jet 3 Diverter Valves V 2 Safety Suction U 5 Mini Skimmer Air Control I 6 Spa Light LI Drain Valve 51 SPECIAL FEATURES Spa Pillows 3 Motion Glow Light Standard Stainless Steel Jetting Optional Waterfall Jet and Control Valve WF Illusion Lighting Opti
11. Optional Stainless Steel Jetting Optional Waterfall Jet WF Optional Waterfall Control Valve Optional SoundWave Audio Optional Ozone Water Purification oz Optional 11 ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 2 0 1 0 HP 2 0 1 0 HP Pump 2 peak Continuous HP 2 6 0 3 0 HP 6 0 3 0 HP Electronics Electrical Can 6 Gecko XM Series Gecko M Series Voltage 240 240 Amperage 40 I 16 1 x 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Spa Side Control 7 600 Series Gecko Gecko GE Deluxe Secondary Spa Side Control 8 Optional 100 Series Gecko Optional Not every jet is referenced Each type of jet is noted for ease of identification Note location of audio components prior to install pas Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice 12 DOMESTIC SE SERIES SPECIFICATIONS COLUMBIA SPA MODEL pas nmm EAS GENERAL rev 3 07 Seating Capacity 5 Shell Material Acrylic Dimensions Domestic 74 6727 sq x 31 277 Dimensions Export 188 cm sq x 79 cm Water Capacity 275 Gallons 1 041 liters Dry Weight 530 Ibs 240 kg Skirt Mat
12. PROCEDURE WHEN REPLACING THE ELEMENT INTO THE HOUSING BE SURE THAT THE O RING IS IN PLACE AND CLEAR TO ASSURE A SNUG FIT OF THE FILTER DOME LID TO PREVENT LEAKAGE HAND TIGHTEN THE LOCK RING UNTIL THE SAFETY TAB CLICKS INTO PLACE RE CHECK BLEEDER VALVE TO BE SURE IT IS CLOSED 39 MAINTENANCE RECOMMENDATIONS PERIODIC SPA WATER DRAINING AFTER A CERTAIN TIME YOU MAY FIND THAT THE ADDITION OF CHEMICALS WILL NOT CLARIFY OR ELIMI NATE ODORS IN THE SPA THIS IS AN INDICATION THAT THE WATER NEEDS TO BE DRAINED AND REPLACED GENER ALLY DEPENDING UPON BATHER LOAD AND WATER CHEMISTRY MAINTENANCE THIS MAY NEED DONE EVERY 3 MONTHS WITH THE USE OF OZONE THIS MAY NEED DONE LESS FREQUENTLY 1 REDUCE SET TEMPERATURE TO 59 F 15 C 2 TURN OFF ALL POWER 3 CONNECT A GARDEN HOSE TO THE RECESSED DRAIN VALVE FOUND ON THE SIDE OF YOUR SPA CABINET BY SLOWLY PULLING THE CAP OUT ALL THE WAY APPROXIMATELY 2 AND TURN CAP COUNTERCLOCKWISE TO REMOVE ATTACH THE HOSE AND PUSH VALVE 1 THIS WILL START THE DRAINING PROCESS AFTER DRAINING THE SPA REPLACE THE CAP AND PUSH THE VALVE ALL THE WAY IN SEE PHOTO NOTE UNSCREW THE LARGE NUT AROUND THE DRAIN VALVE TO REMOVE THE CABINET PANEL FROM THE SPA FOR SERVICING IF NECESSARY 4 CLEAN CARTRIDGE FILTER AS NOTED PREVIOUSLY IN THIS SECTION REGARDING MAINTENANCE RECOMMENDATIONS 5 CLEAN SPA SHELL WITH NON SUDSING CLEANSER 6 FOLLOW INSTRUCTION UNDER START UP PLUMBING CARE ALL SP
13. SAME FUNCTION AS THE SKIMMER IT WORKS IN CONJUNCTION WITH THE SKIMMER TO RETURN WATER TO THE SUPPORT EQUIPMENT AIR CONTROLS THESE ARE ROUND FITTINGS MOUNTED ON THE LIP OF SPA THAT CONTROL THE AMOUNT OF OUTSIDE AIR MIXED WITH THE INCOMING WATER OF THE HYDRO JET YOUR SPA HAS MULTIPLE AIR CONTROLS ON THE SPA LIP THAT CONTROL AIR WATER MIX FOR A SEGMENT OF THE JETS AIR ASSAGE THIS APPEARS AS A NUMBER OF TINY HOLES IN THE SEATING AREA WHEREBY THE BUBBLER BLOWER PUSHES AIR THROUGH FOR EXTRA THERAPY ACTION DELIVERING AN ALL OVER MASSAGE WATER ACTION STANDARD ON THE LX SERIES ULTRA MASSAGE SELECTOR LOCATED ON SPA LIP TURN TO ADJUST PUMP POWER TO SELECTED JETS WHICH ENHANCES WATER ACTION THROUGH THOSE JETS BY DECREASING WATER ACTION THROUGH OTHERS STANDARD ON THE LX SERIES SPA MOOD LIGHT UNDERWATER LOW VOLTAGE LIGHT WITH ADDITIONAL TWO CHANGEABLE COLORED LENSES FOR NIGHT TIME SPA ENJOYMENT STANDARD WITH THE SE SERIES SPAS MOTION GLOW LIGHTING LOW VOLTAGE SPA LIGHT WITH VARYING SHADES OF A COLOR WASH CONTROLLED AT THE SPASIDE CONTROL PANEL CHOOSE ROTATION OF COLOR OR STATIONARY COLOR OF YOUR CHOICE STANDARD WITH THE LX SERIES OPTIONAL ON THE SE SERIES SPAS ILLUSION LIGHTING AS AN OPTION ON THE LX SERIES LED PINPOINT LIGHTS ILLUMINATE WITH UP TO 25 POINTS OF LIGHT ACCENTING THE LIP OF YOUR SPA WITH COLOR OPTIONS OF ROTATING COLORS OR A STATIONARY COLOR OF YOUR SELECTION HYDRO JETS SKIMMER AIR CONTROLS ULTRA
14. SECTION OF THIS MANUAL FOR INSTRUCTIONS ALL SPA SUPPORT EQUIPMENT MUST BE BONDED GROUNDED TO THE PRESSURE CONNECTOR LOCATED WITHIN THE CONTROL PANEL AS WELL AS THE BONDING TERMINAL LOCATED ON THE OUTSIDE OF THE CONTROL PANEL SEE WIRING SCHEMATIC DISCONNECT ALL ELECTRICAL SUPPLIES AND CONTACT A QUALIFIED TECHNICIAN BEFORE SERVICING SPA WIRING SCHEMATIC FOR CERTIFIED ELECTRICIANS REFERENCE ONLY OPTION 1 MAIN PANEL WIRE A WIRE B CIRCUIT BREAKER DISCONNECT 5 FT TO 15 FT GPCL 1 1 52 M TO 4 57 M OPTION 2 MAIN PANEL WIRE A CIRCUIT BREAKER DISCONNECT WIRE B G F C I 5 FT TO 15 FT 1 52 M TO 4 57 M 29 WIRING INSTALLATION WIRING SCHEMATICS ATTENTION ELECTRICIAN ALL PDC SPA UNITS MUST BE INSTALLED WITH AN APPROVED G F C I IN ACCORDANCE WITH ALL APPLICABLE CODES INSTALLATION OF G F C I VARIES AMONG THOSE MANUFACTURERS FOLLOW EACH MANUFACTURER S GUIDELINES TO ENSURE PROPER OPERATION AND PROTECTION OF SPA OCCUPANTS THIS DIAGRAMIS A TYPICAL INSTALLATION TO BE USED ONLY AS A REFERENCE FOR THE INSTALLING ELECTRICIAN TYPICAL INSTALLATION BREAKER BOX CLASS A 50 AMP 120 240 VOLT GFCI GROUND BAR ATTACHED TO BOX INPUT amp OUTPUT LINE BLACK GROUND TO SPA HOUSE INPUT GROUND INPUT LINE RED HOUSE INPUT LOAD 120V BLACK TO SPA PIG TAIL WHITE FROM GFCI BREAKER GOING TO LOAD 120V NEUTRAL BAR IN BO
15. THE LIFE OF THE COVER HANDLE IT WITH CARE AND CLEAN IT REGULARLY USING MILD SOAP AND WATER PERIODIC TREATMENTS WITH A VINYL CONDITIONER WILL HELP PROTECT AGAINST DETERIORATION CAUSED BY UV RAYS FROM THE SUN NEVER ALLOW ANYONE TO STAND OR SIT ON THE COVER AND AVOID DRAGGING IT ACROSS ROUGH SURFACES KEEP COVER LOCKED WHEN NOT IN USE THE FILTER SPA WATER FILTRATION BEGINS AS SOON AS THE FLOW IS STEADY THROUGH THE PUMP THE TOP LOAD PRESSURIZED FILTER ASSURES OPTIMUM CLEANING CAPACITY AS THE FILTER CARTRIDGE REMOVES DIRT FROM THE WATER THE ACCUMULATED DEBRIS WILL CAUSE A RESISTANCE TO FLOW WHEN THIS IS NOTICED ALONG WITH CLOUDY WATER CLEAN OR REPLACE THE FILTER ELEMENT AS NOTED BELOW 1 SHUT OFF POWER AT THE MAIN OR SUB PANEL 2 OPEN THE SMALL BLACK BLEEDER VALVE ON TOP OF THE FILTER COVER SLIGHTLY TO RELEASE PRESSURE BE SURE TO RE CLOSE THE VALVE SNUGLY BEFORE REACTIVATING THE SPA 3 DEPRESS SAFETY TAB NEXT TO THE LID AND REMOVE THE BLACK LOCK RING LIFT THE DOME LID AND REMOVE THE FILTER ELEMENT CLEAN ANY DEBRIS FROM THE FILTER HOUSING SOAK THE FIL TER ELEMENT IN A FILTER CLEANSING SOLUTION AVAILABLE FROM YOUR SPA RETAILER RINSE THE FILTER ELEMENT DOWN WITH A GARDEN HOSE OR PRESSURE HOSE AND REPLACE IN THE FILTER HOUSING IT IS RECOMMENDED TO HAVE AN EXTRA FILTER CARTRIDGE ON HAND SO THAT A CLEAN ELEMENT WILL ALWAYS BE AVAILABLE WHILE THE SOILED ELEMENT IS BEING CLEANED THIS WILL MINIMIZE DOWNTIME OF THE SPA DURING THE CLEANING
16. on and its icon flashes The heater is not allowed also to come on throughout the cool down period of the heater element Light icon The Light icon lights up when the light is on Pumps icons The Pump indicator numbers and their icona become animated when pumps are on wid Smart winter mode icon The SWM icon automatically turns on when freeze protection is active It flashes while system purges the spa plumbing Filter Cycle icon The Filter Cycle icon lights up when filter cycle is on it flashes when filtering is suspended Heater icon The Heater icon lights up when the heater is on Water temperature regulation plumbing in order to ensure accurate water temperature readings as well as avoiding heater activation in dry conditions g In K 100 Control optional This control offers convenience of spa operation at a second location on water flow through the heater housing and the the spa lip Operates pumps 1 2 3 and Light taking a water temperature reading if required the system automatically turns the heater on to reach and maintain water temperature at Set Point Program icon The Program icon lights up when Programming Progress bar A visual indication of the time remaining before an equipment is tumed off or before the end of the mode Set Point icon The Set Point icon automatically turns on when set point setting menu is activated SP message on display It flashes w
17. 1 6 9 sq 38 3727 Dimensions Export 206 cm sq x 97 cm sq Water Capacity 425 Gallons 1 609 liters Dry Weight 645 105 293 kg Skirt Material Permawood or Cedar Water Flow 510 Gallons per Minute WATER SYSTEM photo ref Water Treatment System OZ Ozonator Filter 25 sq ft Slide Valves 6 Mega Swirl Jet 3 Large Euro Jet w Eyeball 18 Mega ssage Jet Ozone Jet Multi ssage Jet Aromatherapy Foot Jet Diverter Valves Safety Suction Mini Skimmer Air Control Spa Light Drain Valve r m lt 35 o o m gt rS SPECIAL FEATURES Spa Pillows 2 Motion Glow Light Standard Stainless Steel Jetting Optional Waterfall Jet and Control Valve WF 1 Illusion Lighting Optional SoundWave Audio Optional less subwoofer ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 2 0 1 0 HP 2 0 1 0 HP Pump 2 peak Continuous HP 2 4 0 2 0 HP 4 0 2 0 HP Pump 3 peak Continuous HP 3 4 0 2 0 HP 4 0 2 0 HP Air Bubbler 4 1 5 HP 1 5 HP Electronics Electrical Can 6 Gecko XM Series Gecko M Series Voltage 240 240 Amperage 50 1 x 16 1 x 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Main Spa Side Control 7 600 Series Gecko Gecko GE Deluxe Secondary Spa Side Control 8
18. 10 SECONDS TIGHTEN UNION AND CONTINUE START UP 6 TURN POWER ON AT MAIN CIRCUIT BREAKER 7 PRESS JET PUMP BUTTON TO ACTIVATE CYCLE 8 TURN ALL AIR REGULATOR KNOBS TO OFF POSITION 9 WHEN THE SYSTEM HAS FULLY PRIMED ALL THE JETS SHOULD BE FREELY ROTATING AND FREE OF EXCESS AIR EXCEPT THE JETS ATTACHED TO OZONE IF THIS OPTION IS INCLUDED ON THE SYSTEM ALLOW THE SYSTEM TO OPERATE FOR FIVE MINUTES IN THIS POSITION 10 SET THE THERMOSTAT TO THE DESIRED TEMPERATURE TO BEGIN HEATING THE SPA WATER THE INDICATOR ICON ON THE SPA SIDE CONTROL WILL BE ON WHEN THE SPA IS HEATING 11 THE ECONOMICAL GRADUAL HEATING OF THE WATER TAKES PLACE OVER A NUMBER OF HOURS DEPENDING UPON THE SIZE OF THE SPA SIZE OF THE HEATER AND THE RECOMMENDED USE OF A PDC SPA COVER WHEN THE DESIRED TEMPERATURE IS REACHED NOT OVER 104 F 40 LEAVE THE THERMOSTAT THIS SETTING THE TEMPERATURE WILL AUTOMATICALLY BE MAINTAINED RE CHECK WATER TEMPERA TURE WITH AN ACCURATE THERMOMETER BEFORE ENTERING THE SPA 12 SET THE FILTRATION PROGRAM TO DESIRED SETTING PER INSTRUCTIONS FOUND IN THE CONTROL CENTER SECTION OF THIS MANUAL 13 CHEMICALLY TREAT THE SPA WATER READ THE SECTION ON WATER CHEMISTRY MAINTENANCE AND FOLLOW INSTRUCTIONS ON CONTAINER OF ANY PRODUCT USED 14 THE SPA WITH THERMAL COVER TO MAINTAIN TEMPERATURE AND LOCK FOR SAFETY OPERATION SYSTEMS Pogemiom Hesfingicos Snunteinicr Standby
19. 14 THE MID POINT 7 IS SAID TO BE PRECISELY NEUTRAL ABOVE WHICH ALKALINITY BECOMES PROGRESS SIVELY GREATER AND BELOW WHICH ACIDITY BECOMES PROGRESSIVELY GREATER PROPERLY BALANCED SPA WATER SHOULD HAVE A PH BETWEEN 7 2 7 8 A TOTAL ALKALINITY OF 75 150 PPM AND AN OPTIMUM RANGE OF 100 400 PPM OF CALCIUM HARDNESS WITHIN THESE LIMITS YOUR SANITIZING CHEMICALS AND FILTERING FUNCTIONS WILL BE MOST EFFECTIVE TEST KITS ARE AVAILABLE TO MEASURE THE PH AND SHOULD BE REPLACED ON AN AT LEAST ANNUAL BASIS TO ASSURE ACCURACY DISINFECTION THE HIGH TEMPERATURE AND INCREASED VELOCITY OF THE WATER AS WELL AS THE HEAVY BATHER LOADS ALL CONTRIBUTE TO THE ORGANIC CONTAMINATION OF SPA WATER IT IS VERY IMPOR TANT TO MAINTAIN AN EFFECTIVE RESIDUAL OF SANITIZING AGENT TO SHOCK TREAT AT PERIODIC INTERVALS AND IF NEEDED TO CONTROL ALGAE GROWTH BROMINE IS THE BEST SUITED SANITIZER FOR SPA WATER ALTHOUGH CHLORINE IS POPULAR AS A SWIMMING POOL SANITIZER THE HIGH TEMPERATURES AND AERATION OF A SPA GREATLY ACCELERATE CHLORINE LOSS FREE CHLORINE REACTS WITH ORGANIC MATERIALS TO FORM COMBINED CHLORINE WHICH IS A POOR DISINFECTANT THAT CAUSES OFFENSIVE ODORS AND OFTEN CAUSES EYE BURN BROMINE IS SIMILAR TO CHLORINE ALTHOUGH IN THE FREE AND COMBINED FORM IT IS AN EFFECTIVE SANITIZING AGENT AND CAUSES NO OFFENSIVE ODOR OR EYE BURN IT IS EASIER TO MAINTAIN A BROMINE RESIDUAL THAN CHLORINE AND IT IS EFFECTIVE OVER A WIDER PH RANGE THAN CHLORINE THE TEST FOR BROMINE SHO
20. A 8 Large Euro Jet w Eyeball E 12 Mega ssage Jet G 8 Ozone Jet 0 2 Aromatherapy AT 1 Diverter Valves 1 Safety Suction U 1 Mini Skimmer K 1 Air Control I 4 Spa Light L 1 Drain Valve 5 1 SPECIAL FEATURES Spa Pillows 4 Motion Glow Light Standard Stainless Steel Jetting Optional 1 Waterfall Jet and Control Valve WF 1 Illusion Lighting Optional SoundWave Audio Optional less subwoofer ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 4 0 2 0 HP 4 0 2 0 HP Air Bubbler 4 1 5 HP 1 5 HP Electronics Electrical Can 6 Gecko XM Series Gecko M Series Voltage 240 240 Amperage 40 1 x 16 1 x 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Main Spa Side Control 7 600 Series Gecko Gecko GE Deluxe Secondary Spa Side Control 8 Optional 100 Series Gecko Optional Not every jet is referenced Each type of jet is noted for ease of identification Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice pas 21 DOMESTIC LX SERIES SPECIFICATIONS FIJI SPA MODEL pas GENERAL rev 3 07 Seating Capacitv 6 Shell Material Acrylic Dimensions Domestic 93 7 9 sq x 39 373 Dimensions Export 236 cm sq x 100 cm Water Capacity 525 Gal
21. AS ARE PLUMBED WITH PLASTIC JETS PIPES AND FITTINGS WHICH ARE GLUED TOGETHER THESE PLASTIC PARTS AND THEIR MANY GLUE JOINTS ARE SUBJECTED TO HARSH TREATMENT EVERY SPA IS TESTED WITH WATER TO ASSURE THERE ARE NO LEAKS WHEN IT LEAVES THE FACTORY HOWEVER SOMETIMES SPAS DEVELOP A LEAK CAUSED BY SHIPPING VIBRATION OVER THE YEARS YOUR SPA IS SUBJECTED TO MANY HOT COLD CYCLES AND THE HIGH PRESSURE GENERATED BY THE POWERFUL JET PUMP WHICH TOGETHER STRESSES THE PIPES AND JOINTS PDC SPAS ARE DESIGNED TO BE OWNER SERVICEABLE WITH EASY ACCESS PANELS ON ALL 4 SIDES OF THE PORTABLE SPA WHICH ALLOW QUICK AND THOROUGH INSPECTION AND REPAIR OF THE PLUMBING SYSTEM SHOULD A LEAK OCCUR FOLLOW THESE INSTRUCTION TO MAKE THE REPAIR 1 REMOVE SIDE PANEL TO LOCATE LEAK MARK THE LEAK WITH A MARKING PEN 2 TURN OFF ALL POWER DRAIN SPA BELOW LEAK ALLOW PLASTIC PARTS TO DRY 3 CONTACT QUALIFIED SERVICE TECHNICIAN TO REPAIR PLUMBING REPLACING THE LIGHT BULB IF THE UNDERWATER LIGHT BULB SHOULD BURN OUT LIGHT MOTION GLOW LIGHTING YOU WILL NEED TO REMOVE THE ACCESS PANEL TO REPLACE IT REFER TO THE MANUAL SECTION REGARDING REMOVAL BE SURE THE POWER IS OFF LOCATE THE LIGHT HOUSING TURN THE HOUSING COUNTERCLOCKWISE AND REMOVE FROM SPA SHELL TO REPLACE THE BULB PULL THE OLD BULB FROM THE HOUSING AND INSERT NEW ONE RE ATTACH THE LIGHT HOUSING TO SPA SHELL REPLACE CABINET PANEL AND ENDS SEE ILLUSTRATIONS Light Housing 40 WINTE
22. CAL TO MAINTAIN TEMPERATURE THAN TO LET THE TEMPERATURE FALL AND THEN WAIT DURING HEAT UP TIME BEFORE SOAKING OZONE ALL SPAS WITH OZONE OPTION FOR SANITATION SHOULD CIRCULATE 16 24 HOURS DAILY USE THE PROGRAMMABLE ELECTRONIC CONTROL CENTER TO PROGRAM THIS OPERATION DOMESTIC SE SERIES SPECIFICATIONS ANTERO SPA MODEL 10 GENERAL rev 3 07 Seating Capacity 3 Shell Material Acrylic Dimensions Domestic 60 5 x 84 T 31 27 Dimensions Export 152 cm x 213 cm x 79 cm Water Capacity 200 Gallons 757 liters Dry Weight 600 Ibs 272 kg Skirt Material Permawood or Cedar Water Flow 187 Gallons per Minute WATER SYSTEM photo ref Water Treatment System Ozone Ready Filter 25 sq ft Slide Valves 2 Mega Swirl Jet 1 Large Euro Jet w Eyeball E 25 Mega ssage Jet G 2 Multi ssage Jet P 0 Ozone Jet O 2 Diverter Valves 1 Safety Suction Ull Mini Skimmer Air Control 111 Spa Light Li Drain Valve 51 SPECIAL FEATURES Spa Pillows 3 Motion Glow Light Optional Stainless Steel Jettin Waterfall Jet Waterfall Control Valve Optional SoundWave Audio N A Ozone Water Purification oz_ Optional ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 4 0 2 0 HP 4 0
23. CHEMISTRY GUIDELINES WATER CHEMISTRY MAINTENANCE cont d YOUR SPA MAY BE EQUIPPED WITH OZONE AS THE SANITIZING AGENT STANDARD ON THE LX SERIES SPAS AND OPTIONAL ON THE SE SERIES UNITS THIS UTILIZES ULTRAVIOLET LIGHT AND OFFERS A HANDS FREE ROUTINE TO SPA WATER CARE THE PH MUST BE MAINTAINED AND SHOCKING MAY BE NEEDED AFTER HEAVY BATHER LOADS WITH THE USE OF OZONE THE PERIODIC DRAINING MAY BE NEEDED LESS FREQUENTLY AND THE BROMINE ODOR NO LONGER AN ISSUE T IS SUGGESTED THAT 24 HOUR CIRCULATION IS REQUIRED TO EFFECTIVELY SANITIZE THE WATER AND A CHLORINE SHOCK USED PERIODICALLY CONTACT YOUR CHEMICAL SUPPLIER FOR MORE INFORMATION OZONE 1 THERE IS NO TEST KIT AVAILABLE TO TEST OZONE PRESENCE IN SPA WATER ALTHOUGH A 24 HOUR CIRCULATION PERIOD IS RECOMMENDED FOR CLEAN CLEAR WATER A CLEAN AFTER RAIN SMELL WILL BE PRESENT WHEN YOU OPEN YOUR SPA COVER AS AN INDICATOR THAT THE OZONE IS DOING IT S JOB 2 A PROPER PH MUST BE MAINTAINED AND A ROUTINE BROMINE OR CHLORINE SHOCK IS SUGGESTED 3 THE OZONE SYSTEM WITH YOUR SPA IS A CORONA DISCHARGE UNIT THAT HAS A BLUE LIGHT AT THE BOTTOM OF THE UNIT INDICATING PROPER FUNCTION TO GAIN ACCESS TO THE OZONE UNIT REMOVE THE CABINET PANEL SIDE AFTER LOCATING THE POSITION OF THE UNIT REPLACEMENT PARTS ARE AVAILABLE FROM YOUR RETAILER OZONE UNIT Location varies with spa model Refer to specifications for location and take note during PROBLEM Green Algae Bl
24. CLIP HAS REMAINED SNAPPED ON THE VALVE STEM DURING SHIPMENT SEE ILLUSTRATION Valve Stem Gate Valve FOR SLIMLINE AND ADVANTAGEPACK DESIGN SPAS THE SPA EQUIPMENT HAS BEEN ASSEMBLED WITH NUMER OUS COLLARS UNIONS FOR EASE OF FUTURE SERVICING LOCATE AND HAND TIGHTEN ALL COLLARS CHECKING FOR ANY WHICH MAY 7 4 HAVE LOOSENED DURING SHIPMENT SEE ILLUSTRATION 1 az E h 1 1 GA Ad pp Collar Gate Valves I VN 17 Collars THE SPA SUPPORT EQUIPMENT MUST BE PLACED AT OR BELOW THE WATER LEVEL OF THE SPA NEVER PLACE THE EQUIPMENT ABOVE THE SPA WATER LEVEL ALL PDC EQUIPMENT MUST BE IN A SHELTERED ENVIRONMENT THAT WILL PROTECT THE EQUIPMENT FROM RAIN SLEET SNOW AND DIRECT SUNLIGHT REFER TO SPA SPECIFICATION PAGES IN THIS MANUAL FOR THE LOCATION OF EQUIPMENT FOR THE MODEL YOU HAVE CHOSEN INSTALLATION AND WIRING IS TO BE COMPLETED BY A QUALIFIED ELECTRICIAN 27 SPA INSTALLATION INSTALLING THE THERMAL COVER REMOVE THE SPA COVER FROM THE BOX AND PLACE IT ON THE SPA PULL DOWN ONE OF THE STRAPS ON THE SPA COVER AND HOLD LATCH AGAINST THE CABINET SIDE PANEL TO POSITION THE LOCK CORRECTLY HAVE A SECOND PERSON HOLD THE STRAP TIGHT ON THE OPPOSITE SIDE OF THE SPA COVER THE SPA COVER MUST BE TIGHT DO NOT PLACE THE LATCH OVER THE GROOVES OF THE CABINET FIN ISH REMOVE THE LATCH FROM THE LOCK ATTACH THE LOCK TO THE CABINET SIDE PANEL WITH THREE 4 SCREWS P
25. E CABINET SIDE OF YOUR PORTABLE SPA BECOME FAMILIAR WITH THE PRECAUTIONS AND EXERCISE SAFETY AND CARE WHILE ENJOYING YOUR SPA SPA SHELL WARNING DECAL A WARNING DECAL HAS BEEN APPLIED TO THE SIDE OF YOUR SPA SHELL TAKE NOTICE READ THE PRECAUTIONS AND ADHERE TO THE GUIDELINES WHILE USING YOUR SPA ENCLOSED WARNING SIGN FOR POSTING LOCATE THE WEATHER RESISTANT SIGN ENCLOSED WITH THIS MANUAL INTENDED FOR PERMANENT POSTING IN AN AREA NEAR THE SPA VISIBLE TO ALL SPA OCCUPANTS NOTIFY THE FACTORY OR YOUR RETAILER SHOULD YOU REQUIRE ADDITIONAL SIGNS OR REPLACEMENTS WARNING READ ALL INSTRUCTIONS BEFORE USING THE SPA PDC SPAS ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT SAVE THIS MANUAL SIGNS AND INSTRUCTIONS FOR FUTURE REFERENCE SPA PARTS IDENTIFICATION SPA PART TERMINOLOGY AND DESCRIPTION HYDRO JETS THESE ARE THE WALL FITTINGS AROUND THE INSIDE PERIMETER OF THE SPA THEY MIX WATER WITH AIR TO PRODUCE LOCALIZED THERAPY IN A STRAIGHT STREAM CIRCULAR MOTION OR IN RANDOM PATTERNS FOR UPPER AND LOWER BACK MASSAGE IN THE LOUNGE AND CONTOURED SEATING AREAS SKIMMER THIS WILL APPEAR AT WATER LEVEL AS A SQUARE INLET OR VERTICAL RECTANGLE INLET THE SKIMMER TRAPS SURFACE DEBRIS THE WATER LEVEL IN THE SPA SHOULD BE KEPT AT THE CENTER OF THE SKIMMER FOR BEST RESULTS SUCTION THIS IS A CIRCULAR FITTING MOUNTED ON THE VERTICAL WALL OF THE FOOTWELL AND SERVES THE
26. ELOPMENT COMPANY INC 75 PALMER INDUSTRIAL ROAD WILLIAMSPORT PA 17701 USA TEL 570 323 3060 WWW PDCSPAS COM FAX 570 323 8485 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS WARNINGS INSTRUCTIONS FOR ALL SPA MODELS 1 6 SPA USE LABELS LOCATION AND REFERENCE 7 SPA PARTS IDENTIFICATION SPA PART TERMINOLOGY AND DESCRIPTION 8 SUPPORT EQUIPMENT TERMINOLOGY AND DESCRIPTION 9 SE SERIES SPAS SPECIFICATIONS 10 15 LX SERIES SPAS SPECIFICATIONS 16 22 INSTALLATION INSTALLATION GUIDELINES SPA LOCATION CONSIDERATIONS INDOORS AND OUTDOORS 23 24 GENERAL LOCATION CONSIDERATIONS 25 EQUIPMENT LOCATION 26 INSTALLING THE THERMAL COVER 27 WIRING INSTALLATION SUPPORT SYSTEM SPECIFICATIONS 28 WIRING SCHEMATICS 29 INITIAL START UP GENERAL GUIDELINES 30 OPERATION SYSTEMS IN K 600 CONTROL LX SERIES SPAS 31 33 IN K 400 CONTROL SE SERIES SPAS 34 35 WATER CHEMISTRY GUIDELINES 36 37 MAINTENANCE RECOMMENDATIONS 38 39 WINTERIZING YOUR HOT TUB 40 TROUBLESHOOTING 41 RECORDS OF SPA CARE 42 PDC Spa 4 PDC SPAS 75 PALMER INDUSTRIAL ROAD WILLIAMSPORT PA 17701 USA 570 323 3060 TEL 570 323 8485 FAX WWW PDCSPAS COM SAFETY INSTRUCTIONS YOU NOW OWN A HIGH QUALITY PDC SPA BUILT FOR YEARS OF ENJOYMENT AND RELAXATION IT IS OF PRIME IMPORTANCE THAT YOU UNDERSTAND THE OPERATION OF YOUR SPA AND ENJOY IT WITH SAFETY IN MIND YOU SHOULD READ THIS MANUAL THOROUGHLY AND UNDERSTAND ALL OF THE SAFETY PRECAUTIONS USING YOUR SPA WITHIN THESE GUIDELI
27. ER QUICK AND CONVENIENT WAY TO PREPARE THE LOCATION SITE NOTE THAT PAVERS STEPPING STONES ETC STILL HAVE A TENDENCY TO SETTLE AND MAY BECOME UNLEVEL AT SOME POINT A REINFORCED CONCRETE SLAB SHOULD BE AT LEAST FOUR INCHES THICK WITH THE REINFORCING MESH OR ROD ATTACHED TO A BOND WIRE MAKE SURE YOUR DIMENSIONS ARE CORRECT AS YOU PREPARE THE SITE FOR YOUR NEW HOT TUB CLICK ONTO THE WEB SITE OR CALL YOUR RETAILER FOR DIMENSIONS OF THE MODEL YOU HAVE CHOSEN ALLOW A PERIMETER OF THE CHOSEN GROUND SURFACE TO EXTEND BEYOND THE SPA ITSELF TO PROVIDE A CLEAN AREA FOR USERS TO GET IN AND OUT OF THE SPA THE SPA LOCATION AND THE SPA ITSELF MUST BE LEVEL BEFORE FILLING WITH WATER SHOULD YOUR SPA SITE BE A WOODEN DECK THIS PROVIDES A CLEAN AREA WITH WEATHER AND ROT RESISTANT QUALITIES IF A PRESSURE TREATED TYPE LUMBER IS USED CONSIDER THE LOAD REQUIREMENTS AND CONSULT A BUILDER TO DETERMINE IF YOUR DECK IS OF ADEQUATE STRENGTH IF INSTALLING YOUR HOT TUB BELOW GRADE CONSIDER ADEQUATE DRAINAGE FOR RUN OFF AND THE UNLIKELY EVENT OF RAPID SPA DRAINAGE ALLOW ADEQUATE SPACE TO ACCESS THE EQUIPMENT BEHIND THE FOUR ACCESS PANELS ON THE HOT TUB CABINET REVIEW THE PAGES IN THIS MANUAL REFERENCING SPA MODEL SPECIFICATIONS FOR THE LOCATION OF THE SUPPORT EQUIPMENT FOR THE MODEL YOU HAVE CHOSEN LEAVE AMPLE ACCESS TO THE GFCI CIRCUIT BREAKER FOR TESTING ETC A QUICK DISCONNECT MANUAL DISCONNECT IS TO BE INSTALLED BETWEEN 5 15 FT 1 5 4 6 M OF THE S
28. ET OF THE SPA MUST BE BONDED TO THE HOME BONDING GRID GROUND FAULT CIRCUIT INTERRUPTER PROTECTION e ALL PDC SPAS ARE PERMANENTLY INSTALLED UNITS GROUND FAULT CIRCUIT INTERRUPTER PROTECTION IS REQUIRED ALL SPA EQUIPMENT SYSTEMS MUST BE PROTECTED BY A CLASS A GROUND FAULT CIRCUIT INTERRUPTER GFCI A GROUND FAULT CIRCUIT INTERRUPTER TYPE CIRCUIT BREAKER NOT SUPPLIED MUST BE INSTALLED IN THE HOME PANEL BOX BY A LICENSED ELECTRICIAN WHEN MAKING WIRE CONNECTION TO THE SPA SUPPORT PACK EQUIPMENT DANGER RISK OF ELECTRICAL SHOCK e INSTALL THE SPA AT LEAST FIVE FEET 1 52 M FROM ALL UNGROUNDED UNBOUNDED METAL SURFACES e GROUND FAULT CIRCUIT INTERRUPTER PROTECTION OF THE HOME POWER SUPPLY TO THE SPA IS NECESSARY YOUR ELECTRICIAN SHOULD EXPLAIN HOW IT WORKS SEE SPA MAINTENANCE e DO NOT PERMIT ANY ELECTRIC APPLIANCE SUCH AS A LIGHT TELEPHONE RADIO OR TELEVISION WITHIN FIVE FEET 1 52 M OF A SPA KEEP ELECTRICAL APPLIANCES AND EXTENSION CORDS AWAY FROM THE SPA WATER IS A CONDUCTOR OF ELECTRICITY SAFETY INSTRUCTIONS DANGER RISK OF ACCIDENTAL DROWNING EXTREME CAUTION MUST BE EXERCISED TO PREVENT UNAUTHORIZED ACCESS BY CHILDREN TO AVOID ACCIDENTS ENSURE THAT CHILDREN CANNOT USE A SPA UNLESS THEY ARE SUPERVISED AT ALL TIMES DANGER TO REDUCE THE RISK OF DROWNING 1 NEVER USE THE SPA ALONE 2 CHILDREN SHOULD NOT USE THE SPA UNLESS THEY ARE SUPERVISED BY AN ADULT 3 KEEP PETS AWAY FROM THE SPA AT ALL T
29. HE G F C I BREAKER AT THE PANEL BOX OR ON THE POWER CORD THE SPA SHOULD SHUT DOWN IMMEDIATELY NOW RESET THE G F C I THE SPA SHOULD RETURN TO NORMAL OPERATION IF THE G F C I FAILS TO OPERATE IN THIS MAN NER THERE EXISTS A POSSIBILITY OF ELECTRICAL SHOCK DISCONTINUE SPA OPERATION BY DISCONNECTING THE POWER SOURCE AND NOTIFY A QUALIFIED ELEC TRICIAN FOR IDENTIFICATION AND CORRECTION OF THE PROBLEM THE SPA SURFACE TO PRESERVE THE SHEEN OF YOUR SPA S SURFACE CLEAN AND SANITIZE THE ACRYLIC SURFACE WITH RUBBING ALCOHOL AVOID USING ABRASIVE CLEANSERS IF YOU ARE NOT CERTAIN AS TO THE SUITABILITY OF A PARTICULAR CLEANSER CONSULT YOUR DEALER DO NOT USE SOAP AS IT CAN CAUSE SUDSING CEDAR CABINET WOOD CEDAR CABINET WITH TIME AND EXPOSURE TO THE ELEMENTS THE WOOD ON YOUR SPA WILL TEND TO LOSE ITS NEW APPEARANCE PROTECTING OR REVIVING THE WOOD SURFACES IS A FAIRLY SIMPLE PROCESS LIGHT SANDING WITH FINE GRIT SANDPAPER WILL HELP SMOOTH ANY ROUGHNESS AND REGULAR APPLICATIONS OF A PENETRATING WOOD PRESERVATIVE WILL ENHANCE AND PROTECT THE RICHNESS OF WOOD PERMA WOOD CABINET YOUR SPA MAY BE CONSTRUCTED FROM A WOOD ALTERNATIVE MATERIAL DESIGNED TO BE DURABLE TOUGH AND VIRTUALLY MAINTENANCE FREE IT MAY REQUIRE PERIODIC CLEANING WITH A NON ABRASIVE CLEANER THE COVER USING THE OPTIONAL INSULATING SPA COVER ANYTIME THE SPA IS NOT IN USE WILL SIGNIFICANTLY REDUCE YOUR OPERATING COSTS HEAT UP TIME AND MAINTENANCE REQUIREMENTS TO PROLONG
30. Hz Pump 1 peak Continuous HP 1 2 0 1 0 HP 2 0 1 0 HP Pump 2 peak Continuous HP 2 4 0 2 0 HP 4 0 2 0 HP Pump 3 peak Continuous HP 3 4 0 2 0 HP 4 0 2 0 HP Air Bubbler 4 1 5 HP 1 5 HP Electronics Electrical Can 6 Gecko XM Series Gecko M Series Voltage 240 240 Amperage 50 1 x 16 1 x 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Main Spa Side Control 7 600 Series Gecko Gecko GE Deluxe Secondary Spa Side Control 8 Optional 100 Series Gecko Optional Not every jet is referenced Each type of jet is noted for ease of identification Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice 20 p DOMESTIC LX SERIES SPECIFICATIONS CABO SPA MODEL GENERAL rev 3 07 Seating Capacity 3 4 Shell Material Acrylic Dimensions Export Dimensions Domestic 60 57 x 84 T x 32 2 8 152 cm x 213 cm x 82 cm Water Capacity 220 Gallons 832 liters Dry Weight 625 108 283 kg Skirt Material Permawood or Cedar Water Flow 187 Gallons per Minute WATER SYSTEM photo ref Water Treatment System OZ Ozonator Filter 25 sq ft Slide Valves 2 Mega Swirl Jet
31. IMES 4 ALWAYS REPLACE AND LOCK THE SPA COVER WHEN THE SPA IS NOT IN USE DANGER TO REDUCE THE RISK OF DROWNING e PROLONGED IMMERSION IN THE SPA MAY CAUSE HYPERTHERMIA THE CAUSES SYMPTOMS AND EFFECTS OF HYPERTHERMIA MAY BE DESCRIBED AS FOLLOWS HYPERTHERMIA OCCURS WHEN THE INTERNAL TEMPERATURE OF THE BODY REACHES A LEVEL SEVERAL DEGREES ABOVE THE NORMAL BODY TEMPERATURE OF 98 6 F 37 C THE SYMPTOMS OF HYPERTHERMIA INCLUDE AN INCREASE IN THE INTERNAL TEMPERATURE OF THE BODY DIZZINESS LETHARGY DROWSINESS AND FAINTING THE EFFECTS OF HYPERTHERMIA INCLUDE 1 FAILURE TO PERCEIVE HEAT 2 FAILURE TO RECOGNIZE THE NEED TO EXIT THE SPA 3 UNAWARENESS OF IMPENDING HAZARD 4 FETAL DAMAGE IN PREGNANT WOMEN 5 PHYSICAL INABILITY TO EXIT THE SPA 6 UNCONSCIOUSNESS RESULTING IN THE DANGER OF DROWNING DANGER RISK OF INJURY DO NOT REMOVE THE SUCTION FITTINGS THE SUCTION FITTING IN THIS SPA IS SIZED TO MATCH THE SPECIFIC WATER FLOW CREATED BY THE PUMP SHOULD THE NEED ARISE TO REPLACE THE SUCTION FITTING OR THE PUMP BE SURE THAT THE FLOW RATES ARE COMPATIBLE NEVER OPERATE THE SPA IF THE SUCTION FITTING IS BROKEN OR MISSING NEVER REPLACE A SUCTION FITTING WITH ONE RATED LESS THAN THE FLOW RATE MARKED ON THE ORIGINAL SUCTION FITTING DANGER RISK OF ACCIDENTAL DROWNING KEEP HAIR AND BODY PARTS AWAY FROM THE SUCTION GUARD DO NOT ALLOW LONG HAIR TO FLOAT FREELY IN THE WATER LONG HAIR SHOULD BE RESTRAINED WITH A BATHING CAP TO RED
32. IT FROM SNOW ICE AND WIND 41 TROUBLESHOOTING A GOOD GENERAL RULE IS TO VISUALLY INSPECT YOUR SPA AND EQUIPMENT AREA FREQUENTLY IF ANYTHING LOOKS BROKEN WORN OR INCORRECT CONTACT YOUR ELECTRICIAN OR SPA RETAILER A SIMPLE REPAIR MAY PREVENT AN INJURY OR MORE SERIOUS PROBLEMS REQUIRING EXPENSIVE REPAIRS IF YOUR SPA IS NOT OPERATING CHECK THE FOLLOWING 1 ALL EQUIPMENT IS IN OPERATIVE e CHECK POWER SOURCE G F C I BREAKER CHECK TO ASSURE SPA HAS DEDICATED CIRCUIT e CHECK THE TEST AND RESET BUTTONS 9 CHECK INTERNAL FUSES 2 PUMP DOES NOT WORK CHECK ALL ITEMS ABOVE CHECK FILTER CLEAN OR REPLACE CARTRIDGE CHECK FOR BLOCKAGES RESTRICTIONS AT SUCTIONS SKIMMER AND PUMP PUSH PUMP BUTTON S TO CHECK IF HIGH SPEED IS FUNCTIONING ON A DUAL SPEED PUMP 3 INADEQUATE JET ACTION e MAKE SURE JETS ARE TURNED ON e MAKE SURE AIR CONTROLS ARE OPEN CHECK FOR RESTRICTIONS BLOCKAGES IN JETS AND OR MAIN SKIMMER AND PUMP CHECK WATER LEVEL PUSH PUMP BUTTON S TO CHECK IF HIGH SPEED IS FUNCTIONING ON A DUAL SPEED PUMP CHECK TO BE SURE THE ULTRA MASSAGE SELECTOR DIVERTER VALVE IS IN CENTER POSITION NOT AVAILABLE ON THE SE SERIES STANDARD ON THE LX SERIES SPAS 4 NO HEAT CHECK ALL STEPS UNDER PART 1 CHECK TEMPERATURE SETTINGS CHECK FOR CLOGGED FILTER ELEMENT AND OTHER RESTRICTIONS CHECK WATER LEVEL CHECK IF PUMP IS RUNNING 5 NO BUBBLER e CHECK ALL S
33. MASSAGE SELECTOR SUCTIONS ape LIGHT HOUSING e MAIN CONTROL CENTER ACRYLIC SPA SHELL TOP LOAD FILTER ADVANTAGEPACK OPTIONAL SUPPORT EQUIPMENT IDENTIFICATION SPA PART TERMINOLOGY AND DESCRIPTION THE SPA SUPPORT PACK CONTAINS UP TO FIVE MAJOR COMPONENTS EITHER SINGLE OR DUAL SPEED PUMPS THAT CIRCULATE THE WATER THROUGH THE HYDRO JETS AND BACK THROUGH THE SUCTIONS A CAR TRIDGE FILTER THAT PHYSICALLY REMOVES DEBRIS FROM THE WATER AND A BUBBLER AIR BLOWER THAT PUSHES AIR THROUGH THE AIR CHANNEL OF THE SPA FOR INCREASED THERAPY YOUR UNIT WILL ALSO BE EQUIPPED WITH AN ELECTRIC HEATER ALL COMPONENTS ARE OPERATED BY SWITCHING AT SPA SIDE WATER IS ROUTED THROUGH THE PUMP FILTER LOCATED ON THE PRESSURE SIDE OF THE PUMP FOR OPTIMUM FILTRATION HEATER AND JETS THE BUBBLER ACTS AS A SEPARATE COMPONENT AND IS USED FOR A SOFT ALL OVER BODY MASSAGE IN THE LX SERIES SPAS PUMP YOUR NEW SPA HAS BEEN EQUIPPED WITH A PUMP FOR HYDROTHERAPY JET ACTION AND WATER FILTRATION THE SPA SUPPORT PACK FEATURES A DUAL SPEED PUMP AND ON SOME MODELS ONE OR TWO ADDITIONAL SINGLE SPEED PUMPS THE DELUXE GE CONTROL CENTER OPERATES THE HIGH SPEED OF A DUAL SPEED PUMP IS ACTIVATED BY THE PUMPI CONTROL AT SPA SIDE THE LOWER SPEED FILTRATION SPEED IS CONTROLLED BY THIS PROGRAMMABLE ELECTRONIC CONTROL THE FILTRATION TIME REQUIRED TO MAINTAIN WARM CLEAN WATER MAY VARY FROM SPA TO SPA GENERALLY NO LESS THAN SIX HOURS A DAY IS RECOMMENDED THE P
34. NES ASSURES YEARS OF FUN AND RELAXATION GAINED FROM ADDING A PDC SPA TO YOUR LIFESTYLE WARNING THIS UNIT IS A PROFESSIONAL GRADE PRODUCT A KNOWLEDGE OF CONSTRUCTION TECHNIQUES PLUMBING AND ELECTRICAL INSTALLATION ACCORDING TO CODES ARE REQUIRED FOR PROPER INSTALLATION AND USER SATISFACTION IT 15 RECOMMENDED THAT A LICENSED CONTRACTOR PERFORM THE INSTALLATION WARRANTY IS VOIDED FOR IMPROPER INSTALLATION RELATED ISSUES SAVE THESE INSTRUCTIONS INCLUDED WITH THIS MANUAL IS A SAFETY SIGN THAT IS TO BE POSTED NEAR THE SPA WHERE ALL OCCUPANTS CAN EASILY READ THIS SIGN IS INTENDED FOR YOU AND YOUR GUEST S PROTECTION SAFETY AND TO ASSURE THEIR SPA ENJOYMENT TAKE THE TIME TO POINT OUT THE LOCATION OF THE SIGN AND INDICATE THE IMPORTANCE OF THE PRECAUTIONS ADHERE THE SIGN WITH SCREWS OR ANOTHER MANNER OF PERMANENT ADHESION SHOULD YOU REQUIRE ADDITIONAL COPIES OR REPLACEMENTS SIMPLY CONTACT THE FACTORY DIRECTLY OR YOUR NEAREST RETAILER SAFETY INSTRUCTIONS as pas READ AND FOLLOW ALL IMPORTANT SAFETY INSTRUCTIONS WHEN INSTALLING AND USING THIS EQUIPMENT BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE TAKEN TO REDUCE THE RISK OF ELECTRICAL SHOCK TO ENSURE SAFE USAGE AND TO SAFEGUARD THE USER S HEALTH READ AND FOLLOW ALL INSTRUCTIONS THIS UNIT IS A PROFESSIONAL GRADE PRODUCT A KNOWLEDGE OF CONSTRUCTION TECHNIQUES PLUMBING AND ELECTRICAL INSTALLATION ACCORDING TO CODES ARE REQUIRED FOR PROPER INSTALLATION AND USER SATISFACTI
35. ON IT IS RECOMMENDED THAT A LICENSED CONTRACTOR PERFORM THE INSTALLATION WARRANTY IS VOIDED FOR IMPROPER INSTALLATION RELATED ISSUES IT IS THE RESPONSIBILITY OF THE HOME OWNER TO ENSURE THAT ALL USERS OF THE SPA ARE ADEQUATELY INFORMED OF ALL PRECAUTIONS USE THE SPA ONLY AS DESCRIBED IN THIS MANUAL THE SPA IS INTENDED FOR HOME USE ONLY DO NOT USE THE SPA IN A COMMERCIAL OR RENTAL SETTING ALL WARRANTIES WILL BE VOIDED GROUND ALL METAL ELECTRICAL EQUIPMENT A GREEN COLORED TERMINAL OR A TERMINAL MARKED G GR GROUND OR GROUNDING IS LOCATED INSIDE THE SUPPLY TERMINAL BOX OR COMPARTMENT THIS TERMINAL MUST BE CONNECTED TO THE GROUNDING MEANS PROVIDED IN THE ELECTRIC SUPPLY SERVICE PANEL USING A CONTINUOUS COPPER WIRE EQUIVALENT IN SIZE TO THE CIRCUIT CONDUCTORS SUPPLYING THIS EQUIPMENT ACCORDING TO BUT NOT LIMITED TO NEC NFPA 70 SECTION 680 40 UL 1563 AT LEAST TWO LUGS MARKED BONDING LUGS ARE PROVIDED THE EXTERNAL SURFACE OR ON THE INSIDE OF THE SUPPLY TERMINAL BOX OR COMPARTMENT CONNECT THE LOCAL COMMON BONDING GRID HOUSEHOLD GROUND IN THE AREA OF THE SPA TO THESE TERMINALS USING AN INSULATED OR BARE COPPER CONDUCTOR NOT SMALLER THAN NO 6 AWG ALL FIELD INSTALLED METAL COMPONENTS SUCH AS RAILS LADDERS DRAINS OR SIMILAR HARD WARE LOCATED WITHIN 5 FEET OF THE SPA OR HOT TUB MUST BE BONDED TO THE EQUIPMENT GROUNDING BUS WITH COPPER CONDUCTORS NOT SMALLER THAN NO 6 AWG ALL METAL SURFACES WITHIN 5 FE
36. OTECTIVE SHIELDS OR BARRIERS ARE SHOWING SIGNS OF DETERIORATION OR IF THERE ARE SIGNS OF OTHER POTENTIAL DAMAGE TO THE UNIT TURN OFF THE UNIT AND REFER SERVICING TO QUALIFIED SERVICE PERSONNEL 8 THIS UNIT SHOULD BE SUBJECTED TO PERIODIC ROUTINE MAINTENANCE FOR EXAMPLE ONCE EVERY 3 MONTHS TO MAKE SURE THAT THE UNIT IS OPERATING PROPERLY SAFETY INSTRUCTIONS ADDITIONAL SAFETY CONSIDERATIONS INSTALL THE SPA TO PROVIDE DRAINAGE FOR COMPARTMENTS OF ELECTRICAL COMPONENTS FOR FLOOR RECESSED SPAS INSTALL TO PERMIT ACCESS FOR SERVICING FROM ABOVE OR BELOW THE FLOOR SPA EQUIPMENT MUST BE INSTALLED BELOW WATER LEVEL WHEN PLANNING YOUR SPA INSTALLATION SITE PREPARE FOR THE UNLIKELY EVENT OF RAPID SPA DRAINAGE DO NOT PLACE SPA IN DIRECT SUNLIGHT WHILE UNIT IS EMPTY OR WHEN SEALED IN SHIPPING MATERIALS EXCESSIVE HEAT BUILD MAY CAUSE DAMAGE TO SPA AND VOID WARRANTY INSTALL SPA SO THAT WATER CAN EASILY BE DRAINED OUT LOCATING THE SIDE DRAIN VALVE ON THE SPA SPECIFICATION LISTING WHEN INSTALLING SPA ALLOW AMPLE SPACE FOR FUTURE SERVICING NOTING LOCATION OF ALL SUPPORT EQUIPMENT PER THE MODEL SPECIFICATIONS SAVE THESE INSTRUCTIONS PD spa O 75 PALMER INDUSTRIAL ROAD WILLIAMSPORT PA 17701 USA 570 323 3060 TEL 570 323 8485 FAX WWW PDCSPAS COM SPA USE LABELS CABINET PANEL WARNING SIGN FOR YOUR REFERRAL AND CONVENIENCE A WEATHER RESISTANT WARNING SIGN HAS BEEN MOUNTED ON TH
37. OWNER S INSTALLATION MANUAL 2007 SE LX SERIES SPAS www pdcspas com IMMEDIATELY UPON DELIVERY REGISTER YOUR HOT TUB ON THE PDC SPAS WEB SITE WWW PDCSPAS COM THIS INFORMATION IS VERX IMPORTANT TO ENSURE WARRANTY COVERAGE AND OBTAIN OWNERSHIP CONTACT INFORMATION FOR POSSIBLE PRODUCT UPDATES PDC SPAS OWNER S MANUAL CONGRATULATIONS ON CHOOSING A QUALITY PDC SPA FOR YOUR BACKYARD RELAXATION PLEASE READ THE OWNER S MANUAL COMPLETELY BEFORE INSTALLING AND USING YOUR NEW SPA THE PURPOSE OF THIS MANUAL IS TO PROVIDE YOU WITH SAFETY OPERATIONAL AND INSTALLATION INFORMATION WHICH WILL ALLOW YOU THE FULLEST ENJOYMENT OF THIS FINE PRODUCT AT THE TIME OF PRINTING THIS MANUAL WAS DEEMED AS ACCURATE AS POSSIBLE PDC SPAS RESERVES THE RIGHT TO CHANGE PRODUCT IN AN EFFORT TO ENHANCE AND IMPROVE WITHOUT PRIOR NOTICE TO BE AWARE OF ANY OF THESE POSSIBLE CHANGES LOG ON TO WWW PDCSPAS COM REFERRING TO THE CUSTOMER CARE SECTION OR CONTACT YOUR RETAILER DIRECTLY OWNERSHIP INFORMATION NAME ADDRESS CITY STATE ZIP INSTALLATION DATE MODEL NAME SERIAL RETAILER NAME RETAILER PHONE NUMBER SERVICE TECHNICIAN CONTACT INFO SERIAL LOCATION THE SERIAL NUMBER CAN BE FOUND ON THE INSIDE OF THE FILTER HOUSING ON THE SPA LIP SIMPLY REMOVE THE PLASTIC FILTER COVER TO REVEAL THE SS E SILVER SERIAL NUMBER PLATE SAVE THIS MANUAL FOR EASY FUTURE REFERENCE RDC PDC SPAS PLASTIC DEV
38. PA AND WITHIN THE OF SIGHT FROM THE HOT TUB CONSIDER WHERE THIS CAN BE LOCATED WHEN SELECT ING AND PREPARING THE SPA SITE ALL WIRING MUST COMPLY WITH THE NATIONAL ELECTRIC CODE A CABINET SIDE DRAIN HAS BEEN INSTALLED ON THE BOTTOM PORTION OF A CABINET SIDEWALL FOR EASY DRAINING LOCATE THIS DRAIN AND LEAVE AMPLE ACCESS YOUR SPA MAY HAVE BEEN CHOSEN WITH THE ADVANTAGEPACK DESIGN WITH THIS FEATURE ALL THE EQUIPMENT IS LOCATED BENEATH AN END CABINET ALLOW EASY ACCESS TO ALL COMPONENTS THIS DESIGN ALSO FEATURES A SIDE DRAIN FOR EMPTYING 26 SPA INSTALLATION EQUIPMENT LOCATION FOR SLIMLINE DESIGN SPAS AFTER THE HOT TUB HAS BEEN PLACED IN THE DESIRED LOCATION REMOVE A CABINET ACCESS PANEL USING A SQUARE HEAD SCREWDRIVER SEE ILLUSTRATION Hot Tub Shell gt LLL NEXT LIFT THE RTB INSULATION BLANKET AND LOCATE THE ELECTRICAL BOX PUMP OR PUMPS AIR BLOWER NOTE THE HEATER ATTACHED BEHIND THE ELECTRICAL BOX BE SURE YOU HAVE ALLOWED AMPLE SPACE AROUND THE NECESSARY CABINET SIDES TO ACCESS EQUIPMENT FOR SLIMLINE AND ADVANTAGEPACK DESIGN SPAS NOTE THE LOCATION OF THE ELECTRICAL BOX THIS WILL NEED TO BE ACCESSED TO COMPLETE THE WIRING CONNECTION TO THE HOME POWER SOURCE SEE PHOTO FOR ADVANTAGEPACK DESIGN UNITS THIS IS LOCATED BENEATH THE END CABINET WITH OTHER SUPPORT COMPONENTS Locking Clip FOR SLIMLINE AND ADVANTAGEPACK DESIGN SPAS CHECK THAT ALL VALVES TWO PER PUMP ARE OPEN AND THE LOCKING
39. RIZING YOUR HOT TUB IF YOUR SPA IS TO BE USED DURING THE WINTER MONTHS IN COLD CLIMATE WHERE THE DANGER OF FREEZING EXISTS CERTAIN PRECAUTIONS SHOULD BE TAKEN TO AVOID DAMAGE AN INCREASED CIRCULATION CYCLE AND USE OF A RIGID FOAM COVER ARE SUGGESTED CONTACT YOUR DEALER FOR ADVICE MANY SPA OWNERS FIND THAT OUTDOOR WINTERTIME SOAKING IS QUITE ENJOYABLE AND PDC CERTAINLY SUGGESTS THE USE OF A SPA YEAR ROUND ALTHOUGH CERTAIN SITUATIONS DO REQUIRE CLOSING THE UNIT FOR THE WINTER MONTHS I E VACATION HOMES IF THE SPA WILL NOT BE USED FOR A PERIOD OF TIME PERFORM THE FOLLOWING WINTERIZING PROCEDURES 1 TURN HEAT ALL THE WAY DOWN AND TURN OFF AT THE BREAKER 2 DRAIN SPA OF ALL WATER 3 REMOVE ANY REMAINING WATER WITH SPONGE 4 REMOVE WATER FROM THE AIR CHANNEL THE LX SERIES SPAS EQUIPPED WITH THE AIR ASSAGE DESIGN TURN POWER BACK ON TURN BUBBLER ON FOR SEVERAL MINUTES TO SPRAY OUT WATER WIPE OUT SPA AND REPEAT AS NECESSARY SHUT OFF ALL ELECTRICAL POWER TO UNIT 5 FILTER SHOULD BE DRAINED REMOVED AND CLEANED STORE IN A DRY PLACE 6 PUMP MOTOR AND ALL CONNECTING LINES SHOULD BE DRAINED FULLY TO PROTECT FROM FREEZING BLOW AIR THROUGH ALL CONNECTION LINES TO REMOVE WATER YOU MAY WISH TO USE A NON TOXIC RV TYPE ANTIFREEZE TO GUARANTEE FREEZE PREVENTION BE SURE TO READ THE MANUFACTURER S INSTRUCTIONS AND REMOVE ALL ANTI FREEZE BEFORE THE NEXT SPA USE 7 COVER THE SPA WITH A WATERPROOF RIGID COVER TO PROTECT
40. ROVIDED ATTACH THE OTHER THREE LOCKS TO THE CABINET IN THE SAME MANNER TO SECURE THE HOT TUB COVER SNAP THE LATCHES ON THE SPA COVER INTO THE LOCKS ON THE CABINET SIDE PANEL TO LOCK THE COVER IN PLACE INSERT THE KEY AND TURN IT CLOCKWISE 1 4 TURN TO UNLOCK THE LATCHES INSERT THE KEY AND TURN IT COUNTER CLOCKWISE 1 4 TURN ALWAYS KEEP THE COVER LOCKED WHEN THE SPA IS NOT IN USE KEEP THE KEYS IN A SAFE PLACE OUT OF THE REACH OF CHILDREN 28 WIRING INSTALLATION c 2 o Spas ees SUPPORT SYSTEM SPECIFICATIONS GECKO SE SERIES SPAS MODEL EQUIPMENT PUMPS SPA CONTROL HEATER TOTAL AMPS DENALI SK 40055 1 5 HP 2 SPEED IN K 400 4KW 39 AMPS BOULDER 3 0 HP 1 SPEED EVEREST VANCOUVER SK 40036 2 HP 2 SPEED IN K 400 28 AMPS ANTERO COLUMBIA LX SERIES SPAS MODEL EQUIPMENT PUMPS amp BLOWER SPA CONTROL HEATER TOTAL AMPS CABO SK60036 2 HP 2 SPEED IN K 600 4KW 28 AMPS REMAINING 6 SK 60085 1 5 HP 2 SPEED and IN K 600 4 KW 40 AMPS LX SPAS 3 5 HP 1 SPEED and 3 5 HP 1 SPEED and 1 5 HP BLOWER ALL EQUIPMENT MODELS ARE 120 240 E ALL SPAS MUST BE PERMANENTLY CONNECTED ALL SPA SUPPORT SYSTEMS ARE MULTIPLE SUPPLY CIRCUITS ALL SPA SYSTEMS REQUIRE THE INSTALLATION OF A GROUND FAULT CIRCUIT INTERRUPTER PROTECTION GFCI AT THE POWER SOURCE NOT SUPPLIED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL CODES AND REGULATIONS e PRIOR TO EACH USE TESTING OF THE GFCI IS REQUIRED REFER TO THE MAINTENANCE
41. S ENCLOSURES CONTAINING OTHER CONDUCTORS UNLESS THE ADDITIONAL CONDUCTORS ARE ALSO PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER THE ELECTRICAL SUPPLY FOR THIS PRODUCT MUST INCLUDE A SUITABLY RATED SWITCH OR CIRCUIT BREAKER TO OPEN ALL UNDERGROUND SUPPLY CONDUCTORS TO COMPLYWITH SECTION 422 20 OF THE NATIONAL ELECTRIC CODE THE DISCONNECTING MEANS MUST BE READILY ACCESSIBLE TO THE TUB OCCUPANT BUT INSTALLED AT LEAST 5 FT 1 5 M FROM THE SPA WATER WARNING FOR SPAS WITH AUDIO VIDEO COMPONENTS 1 CAUTION RISK OF ELECTRIC SHOCK DO NOT LEAVE COMPARTMENT DOOR OPEN 2 CAUTION RISK OF ELECTRIC SHOCK REPLACE COMPONENTS ONLY WITH IDENTICAL COMPONENTS AND 3 DO NOT OPERATE THE AUDIO VIDEO CONTROLS WHILE INSIDE THE SPA 4 WARNING PREVENT ELECTROCUTION DO NOT CONNECT ANY AUXILIARY COMPONENTS FOR EXAMPLE CABLE ADDITIONAL SPEAKERS HEADPHONES ADDITIONAL AUDIO VIDEO COMPONENTS ETC TO THE SYSTEM 5 THESE UNITS ARE NOT PROVIDED WITH AN OUTDOOR ANTENNAE WHEN PROVIDED IT SHOULD BE INSTALLED IN ACCORDANCE WITH ARTICLE 810 OF THE NATIONAL ELECTRICAL CODE ANSI NFPA 70 6 DO NOT SERVICE THIS PRODUCT YOURSELF AS OPENING OR REMOVING COVERS MAY EXPOSE YOU TO DANGEROUS VOLTAGE OR OTHER RISK OF INJURY REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL 7 WHEN THE POWER SUPPLY CONNECTION OR POWER SUPPLY CORD S ARE DAMAGED IF WATER IS ENTERING THE AUDIO VIDEO COMPARTMENT OR ANY ELECTRICAL EQUIPMENT COMPARTMENT AREA IF THE PR
42. T MUST COMPLY WITH THE NATIONAL ELECTRIC CODE 13 LOCATIONS AT LEAST 5 FT 1 52 M FROM ALL METAL SURFACES A SPA MAY BE INSTALLED WITHIN 5 FEET OF METALS SURFACES PROVIDING EACH METAL SURFACE IS PERMANENTLY CONNECTED BY A No 8AWG 8 4 MM2 COPPER CONDUCTOR ATTACHED TO THE WIRE CONNECTOR ON THE TERMINAL BOX PROVIDED FOR THIS PURPOSE ALL INSTALLATIONS MUST COMPLY WITH ARTICLE 680 OF THE NATIONAL ELECTRIC CODE AND ANSI NFPA 70 1984 14 PLACE THE SPA ON A FIRM LEVEL SURFACE THAT WILL NOT SHIFT 24 SPA INSTALLATION INSTALLATION GUIDELINES INDOOR INSTALLATION CONSIDERATIONS 1 LOCAL ELECTRICAL AND PLUMBING CODES 2 VENTILATION FANS AND OR DEHUMIDIFIERS SHOULD BE PROVIDED TO HANDLE THE HIGH HUMIDITY DEVELOPED BY YOUR SPA WALLS CEILING AND WOOD TRIM SHOULD BE RESISTANT ALSO 3 CHEMICALS WILL VAPORIZE FROM THE WATER AND MAY CAUSE AN ODOR AND POSSIBLY CORROSION TO CERTAIN HOME HARD WARE NEVER STORE CHEMICALS INSIDE THE SPA CABINET 4 DURING THE NORMAL USE OF THE SPA WATER WILL ESCAPE THE SPA VESSEL NEVER PLACE THE SPA ON OR OVER ANY MATERIAL WHICH MAY BE DAMAGED BY THIS WATER OR THE CHEMICALS WITHIN THE WATER KEEP DAMAGEABLE MATERIALS FAR ENOUGH AWAY FROM THE SPA TO AVOID WATER DAMAGE EVEN IF THE SPA SHOULD LOSE ALL ITS WATER 5 CONSIDER AND PREPARE FOR THE UNLIKELY EVENT OF RAPID SPA DRAINAGE IF PLACEMENT OF THE SPA IS PERMANENT YOU MAY WISH TO PROVIDE FLOOR DRAINS TO ACCOMMODATE DRAINING ETC ALWAYS LEAVE ROOM ALL ARO
43. TEPS UNDER PART 1 9 BLOWERS GENERALLY NEED NO MAINTENANCE REPLACEMENT IS NORMALLY THE SOLUTION 6 NO LIGHT e CHECK LIGHT BUTTON e CHECK G F C I TEST AND RESET BUTTONS 7 WATER IS CLOUDY 9 INCREASE CIRCULATION CYCLE TEST WATER CHEMISTRY CLEAN REPLACE FILTER CARTRIDGE 8 PUMPS HAVE STARTED FOR MINUTE SEVERAL TIMES AND FILTER INDICATOR IS FLASHING THIS IS A FEATURE OF THE SMART WINTER MODE PROTECTING YOUR SPA FROM THE COLD BY TURNING PUMPS ON FOR MINUTE SEVERAL TIMES A DAY TO PREVENT FREEZING IN PIPES IF ABOVE CHECKS DO NOT SOLVE THE PROBLEM CONTACT A QUALIFIED SERVICE TECHNICIAN 42 ETC RECORDS AND CONTACT INFORMATION ELECTRICIAN COMPANY NAME CONTACT NAME ADDRESS PHONE E MAIL ADDRESS BUILDER MASON COMPANY NAME CONTACT NAME ADDRESS PHONE E MAIL ADDRESS SERVICE TECHNICIAN COMPANY NAME CONTACT NAME ADDRESS PHONE E MAIL ADDRESS GENERAL NOTES SAVE THIS MANUAL FOR FUTURE REFERENCE PDC SPAS 75 PALMER INDUSTRIAL ROAD WILLIAMSPORT PA 17701 USA 570 323 3060 TEL 570 323 8485 FAX WWW PDCSPAS COM
44. TOR PERFORM THE INSTALLA TION OUR WARRANTY DOES NOT COVER IMPROPER INSTALLATION RELATED PROBLEMS 25 SPA INSTALLATION GENERAL LOCATION CONSIDERATIONS REVIEW OUTDOOR INSTALLATIONS AND INDOOR INSTALLATIONS PRIOR TO CHOOSING YOUR SPA LOCATION YOUR SPA SHOULD BE PLACED ON A LEVEL CONCRETE PAD OR ON A DECK DESIGNED TO SUPPORT 6000 LBS 2722 KG OR ON PATIO BLOCKS ON THE GROUND DO NOT PLACE THE SPA ON A DIRT SURFACE OR DIRECTLY ON THE GROUND ONCE YOU HAVE A LOCATION SELECTED THERE ARE SEVERAL ISSUES YOU SHOULD CONSIDER IN PREPARING THE SITE FOR THE HOT TUB INSTALLATION A FLAT LEVEL SURFACE THAT IS STRONG ENOUGH TO SUPPORT YOUR SPA IS REQUIRED ONCE YOUR SPA IS FILLED IT HAS CONSIDERABLE WEIGHT MAKE CERTAIN THE LOCATION YOU CHOOSE CAN SUPPORT A MINIMUM OF 100 LBS 45 4 KG PER SQUARE FOOT LOAD PER RECOMMENDED GUIDELINES STRUCTURAL DAMAGE TO THE SPA RESULTING FROM THE INCORRECT INSTALLATION OF PLACEMENT ON INADEQUATE FOUNDATION IS NOT COV ERED IN THE SPA S LIMITED WARRANTY MOST UNITS ARE INSTALLED OUTSIDE ON GROUND LEVEL ON EITHER A CONCRETE PAD OR A WOODEN DECK IF THE SPA IS NOT ON GROUND LEVEL HAVE A BUILDER DETERMINE IF THE SUPPORT IS ADEQUATE IF THE UNIT IS PLACED DIRECTLY ON THE GROUND YOU WILL WANT TO REMOVE THE GRASSY LEVEL AND PLACE A LAYER OF GRAVEL ON THE SOIL THE BEST WAY TO LEVEL THE GRAVEL MAY BE WITH THE STRAIGHT EDGE OF A PIECE OF SOLID LUMBER TO ACHIEVE A LEVEL SURFACE PAVERS PLACED IN A SAND BASE IS ALSO A RATH
45. UCE THE RISK OF DROWNING FROM HAIR OR BODY ENTRAPMENT INSTALL A SUCTION FITTING S WITH A MARKED FLOW RATE IN GALLONS PER MINUTE THAT EQUALS OR EXCEEDS THE FLOW RATE MARKED ON THE EQUIPMENT ASSEMBLY IF REPLACEMENT OF SUCTION FITTINGS BECOMES NECESSARY WARNING GROUND FAULT CIRCUIT INTERRUPTER PROTECTION GFCI FOR THE SPA SHOULD BE TESTED PRIOR TO EACH USE BY THE HOMEOWNER WITH THE SPA IN OPERATION PUSH THE TEST BUTTON ON THE GFCI CIRCUIT BREAKER AT THE PANEL BOX THE SPA SHOULD SHUT DOWN IMMEDIATELY NOW RESET THE GFCI THE SPA SHOULD RETURN TO NORMAL OPERATION IF THE GFCI FAILS TO OPERATE IN THIS MANNER THERE EXISTS A POSSIBILITY OF ELECTRICAL SHOCK DISCONTINUE SPA OPERATION BY DISCONNECTING THE POWER SOURCE AND NOTIFY A QUALIFIED ELECTRICIAN FOR IDENTIFICATION AND CORRECTION OF THE PROBLEM SAFETY INSTRUCTIONS WARNING TO REDUCE THE RISK OF INJURY DO NOT PERMIT CHILDREN TO USE THIS PRODUCT UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES WARNING TO REDUCE THE RISK OF INJURY THE WATER IN A SPA SHOULD NEVER EXCEED 104 F 40 C WATER TEMPERATURES BETWEEN 100 F 38 C AND 104 F 40 C ARE CONSIDERED SAFE FOR A HEALTHY ADULT LOWER WATER TEMPERATURES ARE RECOMMENDED FOR EXTENDED USE EXCEEDING 10 TO 15 MINUTES AND FOR YOUNG CHILDREN EXCESSIVE WATER TEMPERATURES HAVE A HIGH POTENTIAL FOR CAUSING FETAL DAMAGE DURING THE EARLY MONTHS OF PREGNANCY PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD LIMIT SPA
46. ULD READ PPM IN A RESIDENTIAL SPA DEPENDING UPON BATHER LOAD AMOUNT OF USAGE TYPE OF WATER ULTRAVIOLET EXPOSURE ETC THE AMOUNT OF CHEMICALS NEEDED WILL VARY ON A WEEKLY BASIS A SHOCK TREATMENT SHOULD BE USED TO DESTROY ORGANIC CONTAMINATION NOT READILY DESTROYED BY NORMAL ADDITIONS OF THE SANITIZING AGENT THIS IS ACCOMPLISHED BY USING A POWERFUL LONG LASTING OXIDIZING AGENT CAPABLE OF DESTROY ING THE ORGANIC CONTAMINANTS SO THE SANITIZER CAN BE EFFECTIVE IN KILLING BACTERIA CONTACT YOUR CHEMICAL SUPPLIER FOR THE BEST SHOCKING AGENT IN CONJUNCTION WITH THE LINE OF CHEMICALS BEING USED FOR SPAS INSTALLED OUTSIDE AND DIRECTLY IN SUNLIGHT ALGAE GROWTH MAY BE A PROBLEM IF THIS OCCURS CONTACT YOUR RETAILER OR CHEMICAL MANUFACTURER FOR ADVICE ON THE BEST AGENT AVAILABLE TO HANDLE THIS PROBLEM ABOVE ALL REMEMBER 1 BEFORE USING CHEMICALS READ THE LABELS AND FOLLOW DIRECTIONS CAREFULLY 2 ALWAYS ADD THE CHEMICALS DIRECTLY TO THE SPA WATER EITHER IN A SUITABLE FEEDER DISTRIBUTED OVER THE SURFACE OF THE WATER OR POURED INTO THE WATER PREFERABLY WITH THE PUMP AND BUBBLER ON 3 NEVER ADD CHEMICALS TO THE SPA WHILE PEOPLE ARE USING IT 4 MAINTAINING TEMPERATURE BETWEEN 95 104 F 35 40 IS ESSENTIAL AS A HEALTH FACTOR FOR BATHERS AND IS HELPFUL IN CONTROLLING WATER PROBLEMS 5 THE BOTTOM LINE TO PROPER WATER MAINTENANCE IS TO ADHERE TO A REGULAR SCHEDULE OF TESTING CHEMICAL LEVELS AND MAINTAINING THEM 37 WATER
47. UMPI BUTTON CAN ACTIVATE THE PUMP AT FULL SPEED AT ANY TIME FOR HYDROTHERAPY EVEN THOUGH TURNING OFF THE PUMP AT THE PUMPI BUTTON DOES NOT OVERRIDE THE FILTRATION CYCLE LOW SPEED FOR EXAMPLE IF THE SPA HAS BEEN PROGRAMMED TO CIRCULATE THE SYSTEM AT A TIME WHEN BATHERS ARE EXITING THE SPA THE PUMP WILL CONTINUE TO OPERATE AT LOW SPEED EVEN THOUGH THE JET BUTTON IS PUSHED THE CONTROL UNIT WILL SHUT THE PUMP OFF WHEN PROGRAMMED TO DO SO THE SINGLE SPEED PUMP S IF PRESENT ARE ACTIVATED BY THE PUMP2 OR PUMP3 CONTROL TOP LOAD PRESSURIZED FILTER YOUR PDC SPA IS EQUIPPED WITH A TOP LOAD PRESSURIZED FILTER THIS ASSURES OPTIMUM WATER FILTERING AND EASE OF CLEANING AT SPA SIDE REVIEW THE MAINTENANCE SECTION OF THIS MANUAL FOR FILTER CARTRIDGE CLEANING AND REPLACEMENT AIR ASSAGE AIR BUBBLER THIS EQUIPMENT ACTS INDEPENDENT FROM ALL OTHER SUPPORT EQUIPMENT PACK COMPONENTS IT PUSHES OUTSIDE AIR THROUGH THE AIR CHANNEL FOR GENERALIZED MASSAGE IT IS ACTIVATED BY DEPRESSING THE BUBBLER CONTROL AT SPA SIDE THE BLOWER IS LOCATED BEHIND A CABINET PANEL MAKE NOTE OF THIS LOCATION ALONG WITH ALL OTHERS PRIOR TO INSTALLING HEATER YOUR SPA IS EQUIPPED WITH THERMOSTAT CONTROL AT SPA SIDE ONCE YOU FIND THE TEMPERATURE YOU ENJOY MOST LEAVE THE THERMOSTAT AT THAT SETTING AND THE SPA WILL AUTOMATICALLY MAINTAIN THE CORRECT TEMPERATURE READY FOR YOUR ENJOYMENT ANY TIME OF THE DAY AVOID CONSTANT RESETTING OF THE THERMOSTAT IT IS MORE ECONOMI
48. UND THE SPA FOR EASY ACCESS IN CASE REPAIRS ARE NECESSARY CONSIDER AND PREPARE FOR THE UNLIKELY EVENT OF SPA REMOVAL READ 7 14 IN THE OUTDOOR INSTALLATIONS INFORMATION DO NOT SET SPA ON FINISHED FLOOR WITHOUT A WATERPROOF BARRIER PROTECTION UNDERNEATH vo I THE SPA SHOULD HAVE ACCESS A POWER SOURCE CAPABLE OF SUPPLYING 240 VOLTS AC POWER IT MUST BE WIRED DIRECTLY INTO A GROUNDED CIRCUIT WITH A GROUND FAULT CIRCUIT INTERRUPTER G F C I NO OTHER APPLIANCES SHOULD BE ON THE SAME CIRCUIT 10 THE SPA SHOULD BE CLOSE TO A SOURCE OF WATER 11 BE SURE THAT THE LOCATION YOU CHOOSE IS STABLE IT MUST BE ABLE TO SUPPORT THE WEIGHT OF THE SPA WHEN IT IS FILLED WITH WATER PLUS THE WEIGHT OF THE OCCUPANTS THE SPA MAY WEIGH UP TO 6000 LBS 2722 KG WHEN IT IS FILLED WITH WATER 12 DO NOT USE THE SPA ABOVE A FINISHED LIVING AREA DUE TO THE RISK OF WATER DAMAGE 13 THE SPA IS NOT DESIGNED FOR IN FLOOR INSTALLATION HOWEVER IT IS COMPATIBLE WITH A DECK SYSTEM THAT IS BUILT FLUSH WITH THE TOP OF THE SPA PROVIDED YOU LEAVE ACCESS FOR SERVICE 14 BE SURE TO NOTE ANY OTHER CONSIDERATIONS SUCH AS AESTHETICS OR PRIVACY CONCERNS THAT MAY AFFECT THE SAFETY OR ENJOYMENT OF USING THE SPA WARNING THIS IS A PROFESSIONAL GRADE PRODUCT A KNOWLEDGE OF CONSTRUCTION TECHNIQUES PLUMBING AND ELECTRICAL INSTALLATION ACCORDING TO CODES ARE REQUIRED FOR PROPER INSTALLATION AND USER SATISFACTION WE RECOMMEND THAT A LICENSED CONTRAC
49. X RED TO SPA LOAD NEUTRAL BAR LOAD NEUTRAL gt WHITE TO SPA LINE NEUTRAL WHITE HOUSE INPUT To SPA OUTPUT FROM HOUSE INPUT TO BE NOTED Installation of this GFCI Circuit TO BE NOTED The white Neutral Breaker including ampere sizing and choice of wire from the hack of the GFCI conductor size and type must be completed by a Circuit Breaker MUST he connected qualified electrician in accordance with the to an incoming Line Neuiral The National Electrical Code and all applicab le federal internal mechanism of the GFCI state and local codes and regulations in effect at the requires this Neutral connection for time of installation proper GFCI function IMPORTANT 6 GAUGE COPPER WIRE MUST BE USED TEST GFCI MONTHLY amp PRIOR TO EACH USE 30 INITIAL START UP GENERAL GUIDELINES 1 BE SURE THAT THE POWER IS TURNED OFF AT THE MAIN CIRCUIT BREAKER CAUTION ELECTRIC HEATER ELEMENT MUST BE FULLY SUBMERGED IN WATER BEFORE BEING ENERGIZED FILL SPA TO THE RECOMMENDED LEVEL ASSURING ALL SUCTION OUTLETS ARE COVERED WITH WATER KR Q N MAKE SURE VALVES ON THE SUCTION AND RETURN SIDES OF THE SPA PUMP ARE OPEN TO ALLOW WATER TO FLOW TO AND FROM THE SPA AND SPA SUPPORT SYSTEM 5 CAREFULLY OPEN THE AIR BLEEDER VALVE FOUND ON THE TOP OF THE FILTER UNTIL WATER FLOWS OUT OF THE TOP OF THE VALVE CLOSE VALVE IF THE PUMP IS AIR LOCKED LOCATE PUMP 1 LOOSEN RETURN FITTING FROM THE TOP OF THE PUMP A FEW TURNS AFTER ABOUT
50. ack Algae Unpleasant Odor Burning Eyes Colored Water Hard Water installation positioning BASIC WATER CHEMISTRY CHART DESCRIPTION Green Water Green spots on surface Slippery surface Black spots on spa surface Chlorine like odor Burning sensation in eyes Water in newly filled spa turns black blue or brown when treated with ozone Cloudy water Scaling CAUSE Low ozone bromine or chlorine levels Low algaecide levels Low oxidizer levels Low algaecide levels Combined chlorine and or pH out of balance Copper iron or in water being oxidized by chlorine or ozone Excessive hardness of makeup water or building up of dissolved minerals in the water caused by continued use of spa chemicals REMEDY Superchlorinate Brush spa removing algae Vacuum spa removing algae Increase oxidizer residual Superchlorinate Brush spa removing algae Vacuum spa removing algae Increase oxidizer residual Superchlorinate Balance pH to 7 2 7 6 Adjust pH to 7 2 7 6 Run filter continuously Vacuum settled material Use sequestering agent for prevention Clean filter Filter continuous Adjust pH to 7 2 7 6 Use scale inhibitor Dilute with makeup water 38 MAINTENANCE RECOMMENDATIONS TESTING THE G F C I GROUND FAULT CIRCUIT INTERRUPTER G F C I PROTECTION FOR THE SPA SHOULD BE TESTED PRIOR TO EACH USE BY THE HOMEOWNER WITH THE SPA IN OPERATION PUSH THE TEST BUTTON ON T
51. e Heater icon lights up when the light is on the time remaining up when the heater is on before an equipment Itflashes when is tumed off or 1 there is a call for heat before the end of the and heater has not standby mode started yet 2 heater has just tumed off and element is cooling down or 3 not enough current available to start heater The Filter Cycle icon lights up when filter cycle is Smart Winter Mode icon The SWM icon automa tically tums on when freeze protection is active It flashes while system purges the spa plumbing Set Point icon The Set Point icon automatically tums on when set point setting menu is activated SP message on display Pump 1 key Press Pump 1 key to turn Pump 1 on at low speed Press a second time to turn pump to high speed A third time turns pump off A built in timer automatically turns pump off after 20 minutes unless pump has been manually deactivated first Up Down keys Use Up or Down key to set desired water temperature The temperature setting will be displayed for 5 seconds to confirm your new selection The Set Point icon indicates that the display shows the desired temperature NOT the current water temperature Pump 2 key Press Pump 2 key to turn Pump 2 on Press a second time to turn pump off A built in timer automatically turns pump off after 20 minutes unless pump has been manually deactivated first Programming Mode U
52. ecko 400 Series Gecko GE Deluxe Secondary Spa Side Control 8 N A N A Not every jet is referenced Each type of jet is noted for ease of identification Note location of audio components prior to install Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice DOMESTIC SE SERIES SPECIFICATIONS EVEREST SPA MODEL 14 GENERAL rev 3 07 Seating Capacity 7 Shell Material Acrylic Dimensions Domestic 93 779 sq x 40 3747 Dimensions Export 236 cm sq x 102 cm Water Capacity 520 Gallons 1 968 liters Dry Weight 910 Ibs 413 kg Skirt Material Permawood or Cedar Water Flow 428 Gallons per Minute WATER SYSTEM photo ref Water Treatment System Ozone ready Filter 25 sq ft Slide Valves 4 Mega Swirl Jet A l Large Euro Jet w Eyeball E 1 Mega ssage Jet G 10 Multi ssage Jet 0 Ozone Jet O 2 Diverter Valves 0 Safety Suction U 3 Mini Skimmer Air Control I 4 Spa Light L 1 Drain Valve S d SPECIAL FEATURES Spa Pillows 2 Motion Glow Light Optional Stainless Steel Jetting Optional Waterfall Jet WF Optional Waterfall Control Valve Optional SoundWave Audio Optional
53. erial Permawood or Cedar Water Flow 187 Gallons per Minute WATER SYSTEM photo ref Water Treatment System Ozone ready Filter 25 sq ft Slide Valves 2 Mega Swirl Jet 2 N 4 Large Euro Jet w Eyeball Mega ssage Jet Multi ssage Jet Ozone Jet Diverter Valves Safety Suction Mini Skimmer mm lt o 65 Air Control Spa Light Drain Valve SPECIAL FEATURES Spa Pillows 3 Motion Glow Light Optional Stainless Steel Jetting Optional Waterfall Jet WF Optional Waterfall Control Valve Optional SoundWave Audio N A Ozone Water Purification oz Optional ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 4 0 2 0 HP 4 0 2 0 HP Electronics Electrical Can 6 Gecko XM Series Gecko M Series Voltage 240 240 Amperage 40 I 16 1 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Spa Side Control 7 Gecko 400 Series Gecko GE Deluxe Secondary Spa Side Control 8 N A N A Not every jet is referenced Each type of jet is noted for ease of identification Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice 13 FF spas
54. hen 1 there is a call for heat and heater has not started yet 2 heater has just turned off and element is cooling down or 3 if system is performing a check flow Service icon A problem has been detected Do not enter the water Spa service is required 34 OPERATION SYSTEMS IN K 400 SERIES CONTROL CENTER SE SERIES SPAS Pumps icon The Pump indicator numbers light up and their icons become fast animated when pump or blower are in high speed slower animated icon when pump or blower are in low speed Service icon A problem has been detected Do not enter the water Spa service is C Ce Poeeellooe Standbv Mode kev Standbv message Use Standby key to pause all pumps In order to warn the user the Stby message is displayed during Standby mode Pump will stay turned on if there is a request for more heat Pump 3 key Light key Press Pump 3 key to turn Pump 3 on Press Light key to turn light on Press a Press a second time to turn pump off A second time to turn the light off A built built in timer automatically turns pump in timer automatically turns light off after off after 20 minutes unless pump has 2 hours unless it has been manually been manually deactivated first deactivated first Time temperature amp message digits AM PM F C Filter Cycle icon required Light icon Progress bar Heater icon The Light icon lights Avisual indication of Th
55. is referenced Each type of jet is noted for ease of identification Note location of audio components prior to install Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice DOMESTIC LX SERIES SPECIFICATIONS RENO SPA MODEL GENERAL rev 3 07 Seating Capacity 5 Shell Material Acrylic Dimensions Domestic 86 7727 sq 35 27117 Dimensions Export 218 cm sq x 89 cm Water Capacity 425 Gallons 1 609 liters Dry Weight 645 Ibs 293 kg Skirt Material Permawood or Cedar Water Flow 510 Gallons per Minute WATER SYSTEM photo ref Water Treatment System OZ Ozonator Filter 25 sq ft Slide Valves Mega Swirl Jet Large Euro Jet w Eyeball Mega ssage Jet Ozone Jet Multi ssage Jet Aromatherapy Foot Jet Diverter Valves Safety Suction Mini Skimmer Air Control Spa Light Drain Valve m lt 23 s o o m gt Q N e ID SPECIAL FEATURES 22 Spa Pillows 4 Motion Glow Light Standard Stainless Steel Jetting Optional Waterfall Jet and Control Valve WF 1 Illusion Lighting Optional SoundWave Audio
56. lons 1 987 liters Dry Weight 865 165 392 kg Skirt Material Permawood or Cedar Water Flow 510 Gallons per Minute WATER SYSTEM photo ref Water Treatment System OZ JOzonator Filter 25 sq ft Slide Valves 6 Mega Swirl Jet 6 Large Euro Jet w Eyeball Mega ssage Jet Ozone Jet Multi ssage Jet N Aromatherapy Foot Jet Diverter Valves Safety Suction Mini Skimmer Air Control Spa Light Z 2 oom Q 2 Drain Valve SPECIAL FEATURES Spa Pillows 4 Motion Glow Light Standard Stainless Steel Jetting Optional Waterfall Jet and Control Valve WF 1 Illusion Lighting Optional SoundWave Audio Optional ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 2 0 1 0 HP 2 0 1 0 HP Pump 2 peak Continuous HP 2 4 0 2 0 HP 4 0 2 0 HP Pump 3 peak Continuous HP 3 4 0 2 0 HP 4 0 2 0 HP Air Bubbler 4 1 5 HP 1 5 HP Electronics Electrical Can 6 Gecko XM Series Gecko M Series Voltage 240 240 Amperage 50 1 x 16 1 x 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Spa Side Control 7 600 Series Gecko Gecko GE Deluxe Secondary Spa Side Control 8 Optional 100 Series Gecko Optional Not every jet
57. n Note location of audio components prior to install Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice 19 DOMESTIC LX SERIES SPECIFICATIONS BERMUDA SPA MODEL pas GENERAL rev 3 07 Seating Capacity 6 Shell Material Acrylic Dimensions Domestic 90 776 x 79 6777 x 36 37 Dimensions Export 229 cm x 201 cm x 92 cm Water Capacity 325 Gallons 1 230 liters Dry Weight 650 Ibs 295 kg Skirt Material Permawood or Cedar Water Flow 510 Gallons per Minute 3 WATER SYSTEM photo ref Water Treatment System OZ Ozonator Filter 25 sq ft WF Slide Valves 6 Mega Swirl Jet A 9 Large Euro Jet w Eyeball E 24 Mega ssage Jet G 6 Ozone Jet 2 Multi ssage Jet P 3 Aromatherapy ATI Foot Jet 3 Diverter Valves V 2 Safetv Suction U 5 Mini Skimmer Ki Air Control I 6 Spa Light L 1 Drain Valve 5 1 SPECIAL FEATURES Spa Pillows 3 Motion Glow Light Standard Stainless Steel Jetting Optional Waterfall Jet and Control Valve WF 1 Illusion Lighting Optional SoundWave Audio Optional less subwoofer ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50
58. onal SoundWave Audio Optional ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 2 0 1 0 HP 2 0 1 0 HP Pump 2 peak Continuous HP 2 4 0 2 0 HP 4 0 2 0 HP Pump 3 peak Continuous HP 3 4 0 2 0 HP 4 0 2 0 HP Air Bubbler 4 1 5 HP 1 5 HP Electronics Electrical Can 6 Gecko XM Series Gecko M Series Voltage 240 240 Amperage 50 1 x 16 1 x 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Main Spa Side Control 7 600 Series Gecko Gecko GE Deluxe Secondary Spa Side Control 8 Optional 100 Series Gecko Optional Not every jet is referenced Each type of jet is noted for ease of identification Note location of audio components prior to install Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice DOMESTIC LX SERIES SPECIFICATIONS BALI SPA MODEL GENERAL rev 3 07 Seating Capacity 7 Shell Material Acrylic Dimensions Domestic 93 779 sq x 39 33 Dimensions Export 236 cm sq x 100 cm Water Capacity 650 Gallons 2 460 liters Dry Weight 908 Ibs 412 kg Skirt Material Permawood or Cedar Water Flow 510 Gallons per Minute WATER SYSTEM photo ref Water Treatment System OZ Ozona
59. ower kev to turn blower on Press a second time to turn blower off A built in timer automaticallv turns blower off after 20 minutes unless blower has been manually deactivated first 32 OPERATION SYSTEMS IN K 600 SERIES CONTROL CENTER LX SERIES SPAS Light key 5 Press Light key to turn light on Press a second time to turn light off A built in timer automatically turns light off after 2 hours unless it has been manu ally deactivated first Setting the time Enter Programming mode by holding Prog key pressed down for 3 sec The display will show the current time setting Setting the hour Use or key to change hour setting AM PM Setting the minutes Press Ok key Use or key to change minutes set ting T keys Use or key to set desired water tem perature The temperature setting will be displayed for 5 seconds to con firm your new selection The Set Point icon indicates that the dis play shows the desired temperature NOT the current water temperature Setting filter cycle start time To program the filter cycle you must enter these parameters the start time duration and frequency During a filter cycle pumps run for one minute to purge the plumbing then Pump 1 low speed runs for the programmed number of hours Press Ok key a second time The display will show FSxx with xx representing the starting hour Use or
60. rl Jet 2 Large Euro Jet w Eyeball um Mega ssage Jet Multi ssage Jet Ozone Jet Diverter Valves Safety Suction Mini Skimmer Air Control Spa Light Drain Valve lt o s Q m gt m N Go SPECIAL FEATURES Spa Pillows 0 Motion Glow Light Optional Stainless Steel Jetting Optional Waterfall Jet WE Optional Waterfall Control Valve Optional SoundWave Audio N A Ozone Water Purification oz Optional ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 4 0 2 0 HP 4 0 0 HP Electronics Electrical Can 6 Gecko XM Series Gecko M Series Voltage 240 240 Amperage 40 I 16 1 x 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Spa Side Control 7 Gecko 400 Series Gecko GE Deluxe Secondary Spa Side Control 8 N A N A Not every jet is referenced Each type of jet is noted for ease of identification Equipment location relates to slimline design AdvantagePack option has major components located beneath end cabinet All specifications are accurate at time of print Manufacturer reserves the option to change product without prior notice PDC DOMESTIC LX SERIES SPECIFICATIONS ANTIGUA SPA MODEL spas GENERAL rev 3 07 Seating Capacity 8 Shell Material Acrylic Dimensions Domestic 8
61. run for one minute to purge the plumbing then Pump 1 runs for the programmed number of hours Press Light key a third time The display will show FSxx with xx represent ing the starting hour Use Up or Down key to change setting Setting Filter Cycle Duration Press Light key a fourth time The display will show Fdxx with xx representing the duration in hours Use Up or Down key to change setting Water Temperature Regulation In a regulation cycle the system first generates water flow through the heater housing and the plumbing in order to ensure accurate water temperature read ings as well as avoiding heater activation in dry conditions After verifying pump activation and taking a water temperature reading if required the system automatically turns the heater on to reach and maintain water temperature at Set Point Smart Winter Mode Our Smart Winter Mode protects your system from the cold by turning pumps on several times a day to prevent water from freezing in pipes 36 WATER CHEMISTRY GUIDELINES WATER CHEMISTRY MAINTENANCE PH CONTROL CHEMICALLY BALANCED WATER DEPENDS PRIMARILY ON 1 THE AMOUNT OF ACID OR BASE IN THE WATER PH 2 THOSE CHEMICALS THAT HELP MAINTAIN OR STABILIZE PH TOTAL ALKALINITY AND 3 THOSE CHEMICALS THAT CAUSE SCALING CALCIUM HARDNESS DESCRIBED AS A MEASURE OF RELATIVE ACIDITY OR ALKALINITY OF WATER PH IS MEASURED ON A NUMBER SCALE FROM 0
62. se Light key to enter Programming menu by pressing and holding key In Programming mode the following pa rameters can be set time filter cycle start time filter cycle duration filter cycle frequency and temperature unit 35 OPERATION SYSTEMS SERIES CONTROL CENTER SE SERIES SPAS 400 Setting the Time Enter Programming mode by holding Light key pressed down for 3 sec The display will show the current time setting Setting the hour Use Up or Down ar rows to change hour setting AM PM Setting the minutes Press Light key a second time Use Up or Down key to change minutes setting Filter Cycle Frequency Press Light key a fifth time The display will show FFxx with xx representing the number of filter cycles per day up to 4 Use Up or Down key to change setting Cooldown Setting Temperature Unit Water temperature can be displayed in either Fahrenheit F or Celsius Press Light key a sixth time The dis play will show either F or C Use Up or Down key to change setting While performing these tasks the heater is not allowed to turn on and its icon flashes The heater is not allowed also to come on throughout the cool down period of the heater element Setting the Filter Cycle Start Time To program the filter cycle you must enter these parameters the start time duration and frequency During a filter cycle pumps
63. tor Filter 25 sq ft Slide Valves 6 Mega Swirl Jet 6 Large Euro Jet w Eyeball 20 Mega ssage Jet Ozone Jet Multi ssage Jet Aromatherapv Foot Jet Diverter Valves Safetv Suction Mini Skimmer Air Control Spa Light Drain Valve c7 lt s s o o m gt GA SPECIAL FEATURES Spa Pillows 4 Motion Glow Light Standard Stainless Steel Jetting Optional Waterfall Jet and Control Valve WE Illusion Lighting Optional SoundWave Audio Optional 18 PDC ELECTRICAL SYSTEM Pump Information Reference Number Domestic 60Hz Export 50Hz Pump 1 peak Continuous HP 1 2 0 1 0 HP 2 0 1 0 HP Pump 2 peak Continuous HP 4 0 2 0 HP 4 0 2 0 HP Pump 3 peak Continuous HP 4 0 2 0 HP 4 0 2 0 HP Air Bubbler 2 3 4 1 5 HP 1 5 HP Electronics Electrical Can Gecko XM Series Gecko M Series Voltage 240 240 Amperage 50 I 16 1 x 32 3x 16 Heater 6H 4 0 KW 3 0 KW Operation System Main Spa Side Control 600 Series Gecko Gecko GE Deluxe Secondary Spa Side Control Optional 100 Series Gecko Optional Not every jet is referenced Each type of jet is noted for ease of identificatio

Domestic owners manual 2007

Contents

Download Pdf Manuals

Related Search

Related Contents