Offices and Service Centres This Manual
Contents
1. 150 Opening BINARY mode data connection for tmp sn110 chk 226 Transfer complete 1800488 bytes sent in 3 99 seconds lt 451 70 Kbytes sec gt ftp gt quit 221 Goodbye C tmp gt us 9 Telnet onto SN110 10 Type usr bin flashsw sh then press Enter ge Telnet 192 168 11 123 Connect Edit Terminal Help Using anonymous ftp enter the default user name and password ftp Type put c tmp sn110 chk tmp sn110 chk the press Enter uClinux command shell version 2 0 gt usribin mkspace sh Stopping Node Now use ftp binary mode to copy install file to tmp sn110 chk After file has been copied run usr bin flashsw sh gt lusr bin flashsw sh Verifying checksum of install file 11 The software license will be displayed and the new software is then loaded to flash memory on the SN110 Node 12 On completion of the software installation the SN110 node will automatically reboot 13 End Telnet session Page 10 gk Telnet 192 168 11 123 Connect Edit Terminal Help 8 COPYRIGHT Copyright and all other rights in the Software and associated data and printed material supplied by Strand shall at all times remain in the ownership of Strand The Licensee may not copy the printed materials accompanying the software 9 APPLICABLE LAW This licence shall be interpreted in accordance with the laws of England Operating Software installation in progress Please wait Verifying 1966080 bytes Wrote 1802. OFF Specifies that this port is not being used REPORTER specifies that the incoming signals from the dimmer rack s are directed to the Console Reporter for fault reporting When REPORTER is selected the START and END slots are automatically set to 1 and 512 respectively Note When used with an SLD Dimmer the SN110 Port 1 is used as the Reporter Port and Port 2 as the DMX Out Port into the DMX Rack Label This field contains a character string of up to eight characters used to identify the function of the DMX Port Monitor This field determines which of the 512 outputs from the DMX port are displayed on the status bars below the DMX ports at the bottom of the LCD on the SN110 Node Any output between 1 and 512 can be entered Start End and NetSlot Fields These fields allow you to enter a range of outputs to be included within a netslot for each DMX Port Initially the window permits two ranges of net slots to be entered However when the second range is entered and the Submit button pressed another blank row is added permitting another range of outputs to be entered for another NetSlot This will continue until all ranges of outputs have been entered Priority Each NetSlot can be set as one of three priority levels or none by selecting from the drop down menu 1v 2 3 Page 6 Fitting and Wiring the Nodes RJ45 Connector 24V DC Connector RJ45 Connector 24V DC Connector SN110 Nodes Installation Man
3. e P Address A unique identifier on a network using the TCP IP protocol to route data to a particular node within the network The format of an IP Address is a 32 bit numeric address comprising four numbers separated by periods Each number can be 0 to 255 The first three sets of numbers on a Class C network identify the network and the last set of numbers identifies the node Note All Network Nodes must have a unique IP Address and Node Name e IP Netmask This is used only in large networks comprising sub networks Refer to your network administrator e IP Gateway This is only used in large networks that require routing between sub networks Refer to your network administrator e Ethernet MAC A number which is factory set within each node and used to identify a particular item on the Ethernet Network This number is fixed for each hardware item on the network Page 5 LCD DMX Configuration Page LCD Contrast 0 63 Backlight Port 1 Type Label Monitor 0 Off 1 512 Dux our Poti 512 Start End NetSlot Priority HTP JL 3L 9L MS JL L9 19 Port 1 Port 2 Type Label Monitor 0 Off 1 512 DMX OUT Port 1 Start End NetSlot Priority HTP DOCCE 19 J 1 LE 1m Submit Update configuration Reset Cancel changes LCD DMX configuration Network configuration Operating Software v2 5n Press here to view network status For more informa
4. Power Over Ethernet Ethernet Hub Power Over Ethernet 48V DC Mid Span Insertion Unit Strand 65110 PoE SN110 Nodes SN110 Nodes Installation Manual 7 Fitthe node assembly into the back box taking care not to foul any components on the top or bottom lip of the back box 8 Screw the front plate to the back box or to the facia plate if the back box is flush mounted using the four M3 x 8 screws removed prior to installation of the back box 9 Fitthe plastic front panel and secure using the two M3 x 8 screws removed prior to installation of the back box 10 Switch on the mains supply 75785 6 Node The 75785 6 Node is designed to be fitted into a Strand Lighting SLD Dimmer Rack processor housing in the blank space above the power supply module To fit the pre configured node the the SLD Rack proceed as follows 1 Switch off all power the the SLD Dimmer Rack 2 Remove the four screws securing the blanking plate above the power supply unit and remove the blanking plate 3 Before installing the node ensure that the power cables in the power supply module are clear of the SN110 Node tray 4 Connect the power cable supplied between the lower RJ45 socket on the node main board and the SWC connector on the SLD Dimmer Rack backplane board 5 Connect the RJ45 RJ45 cable supplied between the upper RJ45 socket on the node main board and the DMX A Reporter RJ45 socket on the SLD Dimmer Rack backplane board 6 Fitthe 75785 6 No
5. a Windows PC 4 Pre Configuring the Network Nodes ees 5 Fitting and Wiring the NOdES meme 7 Power Over Ethernet sssssss 8 Operation icta e qr nanan 9 Changing the LCD DMX Configuration On Line 9 Viewing the NetworkStatus 9 Installing New Software eneee 10 SN110 Nodes Installation Manual Page 1 General SN110 Variants SN110 Node Model 65110 amp 65111 SN110 Nodes Installation Manual The SN110 Dual Port Ethernet DMX Nodes provide compact and cost effective networking solutions for lighting facilities of any size Based on a 32 bit ARM processor all SN110 nodes utilise the Linux operating system for stable 10 100BT operation Nodes may be configured with Strand s popular ShowNet Pro software or with any browser connected to the Ethernet Network including the new Strand Lighting Wireless Focus Remote The SN110 Network Node is available in five different configurations as follows e Catalogue No 65110 SN110 Node Powered over Ethernet or Local 24V DC Supply e Catalogue No 65111 SN110 Node with Internal Power Supply 120 230V e Catalogue No 65112 Main Board and LCD Board for mounting in OEM Equipment e Catalogue No 75785 SN110 Node for mounting in SLD Series Dimmer Rack Strand Part No 75600A and 75600A CE Catalogue No 75786 SN110 Node for m
6. components within the box when the node is fitted Fit the facia plate to the back box using the two countersunk screws supplied Insert the back box in the wall and secure the conduit to back box Fix the facia plate to the wall using suitable countersunk screws and wall fixings Leave the cables in the back box ready for connection Note The mains supply to a 65111 node should be connected via a switched fused supply for safety and maintenance Page 4 Setting up Networking on a Windows PC Pre Configuring the Network Nodes Network Configuration Page suo Node Name 192 168 071 IP Address 255 255 255 0 IP Netmask oo o0 IP Gateway Ethernet MAC 00 E0 01 00 1F 9E Submit Update configuration Reset Cancel changes LCD DMX configuration Network configuration Operating Software v2 5n Press here to view network status For more information see our web site or email technical support SN110 Nodes Installation Manual In order to set up networking on your PC you must have TCP IP Protocol installed and a Network Interface Card For example in a Windows 95 98 environment From the Start menu select Settings Select Control Panel Select the Protocol tab Select TCP IP and Properties If an IP Address and Netmask is already configured note the settings If no IP Address and Netmask is specified select Specify an IP Address and
7. 0488 bytes Verifying 1800488 bytes Operating Software installation complete Shutdown and reboot of node in progress Power cycle if not rebooted after 30 seconds Please now close this telnet window Shutting down then rebooting SN110 Nodes Installation Manual Page 11
8. 110 Node can be powered by an IEEE 802 3af non compliant PSE however the above features may not apply If using a non compliant PSE it is therefore important to ensure that power is not supplied over the ethernet to nodes fitted with an integral power supply or supplied with 24V DC from an external source Page 8 Operation SN110 LCD SN110 1 192 168 0 11 LABEL 1 DMX OUT LABEL 2 DMX OUT Changing the LCD DMX Configuration on Line Viewing the Network Status During normal operation the SN110 Nodes will display The Node Name Node Address and the DMX label and DMX Type of both DMX Ports on the node A status bar for each port will also continuously monitor the DMX activity for the monitor channel set in the DMX configuration page When there is no Ethernet activity on the DMX port for the selected function type e g DMX IN DMX OUT or REPORTER the DMX function is shown with a strike through e g DMXJN The status and brightness of the LCD backilght and the configuration of the DMX ports on each SN110 node on an Ethernet Network can be changed using a PC connected to the network or a with a 66130 Wireless Focus Remote Unit fitted with an WiFi PC Card Strand Software and a Wireless Access Point Select the internet browser on the PC or Wireless Remote and enter the IP Address of the node to be reconfigured The LCD DMX window will be displayed LCD Settin The intensity of the LCD backlight can be set to suit the lig
9. This Manual Offices and Service Centres SN110 Nodes Installation Manual The material in this manual is for information purposes only and is subject to change without notice Strand Lighting assumes no responsibility for any errors or omissions which may appear in this manual For comments and suggestions regarding corrections and or updates to this manual please contact your nearest Strand Lighting office EI contenido de este manual es solamente para informaci n y est sujeto a cambios sin previo aviso Strand Lighting no asume responsabilidad por errores o omisiones que puedan aparecer Cualquier comentario sugerencia o correcci n con respecto a este manual favor de dirijirlo a la oficina de Strand Lighting m s cercana Der Inhalt dieses Handbuches ist nur f r Informationszwecke gedacht Aenderungen sind vorbehalten Strand Lighting uebernimmt keine Verantwortung f r Fehler oder Irrtuemer die in diesem Handbuch auftreten F r Bemerkungen und Verbesserungsvorschlaege oder Vorschlaege in Bezug auf Korrekturen und oder Aktualisierungen in diesem Handbuch moechten wir Sie bitten Kontakt mit der naechsten Strand Lighting Niederlassung aufzunehmen Le mat riel d crit dans ce manuel est pour information seulement et est sujet changements sans pr avis La compagnie Strand Lighting n assume aucune responsibilit sur toute erreur ou ommission inscrite dans ce manuel Pour tous commentaires ou suggestions concernant des correcti
10. ay New York NY 10010 Tel 001 212 328 3215 Installation Manual SN110 Nodes Document No 40B 1022 Date November 2002 SN110 Nodes Installation Manua Prefix SN110 Nodes Installation Manual Thank you for choosing the Strand Lighting SN110 Node We trust that the equipment will meet all your requirements and will provide you with reliable service for many years to come Strand Lighting can assure you that every effort has been taken to ensure that the equipment has been designed to meet the highest professional standards and that the assembly and testing of the node has been inspected and tested in accordance with our strict quality assurance program The SN110 Nodes also comply with the requirements of UL cUL and CE Should you encounter any problems or difficulties associated with your SN110 Node please contact your nearest Strand Service representitive A complete list of Strand offices and service centres throughout the world is provided at the front of this manual or is available from our website at http www strandlighting com This manual describes the installation and operation of the SN110 range of Ethernet DMX Nodes Contents General ori loi 2 SN110 Variants 5 3 ia e e e tede Me ata tel 2 Safety Warnings A ded e ave un aA ies 3 Electrical SUpplies aa ese det adie tea atone 3 installation ssc e o eee es oe ica 4 Fitting the 65110 65111 Back Boxes sse 4 Setting up Networking on
11. crews safe for later use Remove the four M3 x 8 screws securing the node electronics assembly to the back box and separate the electronics assembly from the back box taking care not to foul any of the components on the top or bottom lip of the back box Keep the screws safe for later use Determine the most suitable position for cable entry and drill a hole in the back box for cable entry Ensure that the hole allows cables to enter the box without fouling any components within the box when the node is fitted Ensure that the back box is level by placing a spirit level on top of the box and mark the four fixing holes Drill four 5mm fixing holes in the wall and secure the back box to the wall using M6 screws and suitable wall fixings Secure the conduit to the back box and leave the cables in the back box ready for connection Remove four M3 x 8 Screws Fit Back Box to Wall Remove Node Assembly Flush Mounting 1 6 7 8 The Model 65110 and 65111 Nodes are suitable for flush wall mounting In this case a facia plate Strand Part No 65113 should have been ordered with each node Prepare the wall by cutting a square hole 114 x 114mm 4 5 in x 4 5 in by 110mm 4 34 in deep Remove the node electronics assembly from the back box as described above Determine the most suitable position for cable entry and drill a hole in the back box for cable entry Ensure that the hole allows cables to enter the box without fouling any
12. de into the slot in the dimmer rack and secure using the screws removed from the blanking plate 65112 OEM Boards A version of the SN110 Node comprising the main PCB and the display unit is available for users of non standard products It is the responsibility of the user to determine how best to install these items in their equipment As part of this responsibility they will be required to ensure that the method used to install the units complies with the applicable National Safety and EMC requirements Power to the 65110 Node can be supplied over the Ethernet Network at the standard Power Over Ethernet PoE voltage of 48V DC PoE technology enables Ethernet nodes to be fitted without the time and cost required to install separate power cabling Using PoE the SN110 nodes can reliably receive data and power over a single standard Category 5 cable Power is injected into the Ethernet cable between the hub and the outgoing network cables to the SN110 Nodes using a PoE Mid Span Insertion Unit as shown The 65110 Node is IEEE 802 3af compliant and will provide the following features when connected to IEEE 802 3af compliant Ethernet Power Sourcing Equipment PSE e The PSE will only switch on power to a IEEE 802 3af compliant node The PSE will not switch on power to the node if it is already powered by other means e The PSE will detect faults on the ethernet cable and will switch off the power in the event of a short circuit The 65
13. enter the IP Address 192 168 0 150 and Subnet Mask 255 255 255 0 7 Click OK to finish and restart your PC OORUN New network nodes are configured at the factory with common default values It is therefore necessary to change the network configuration for each node before it is installed on the network It is logical that the configuration of the DMX ports and the LCD setting should be done at the same time and each SN110 Node labelled with its IP Address ready for installation in the appropriate back box or SLD Dimmer Rack The default Network Configuration of all SN110 Nodes is as follows e Node Name SN110_71 e IP Address 192 168 0 71 e P Netmask 255 255 255 0 e P Gateway 0 0 0 0 Select the Network configuration page as follows 1 Using a standard 24V DC power supply connect the supply via a Molex Type KK socket to the 24V DC input plug on the node main board 2 With the SN110 Node connected to the PC Ethernet port via a standard Ethernet Crossover Cable open the browser window and enter the default IP Address of the SN110 Node http 192 168 0 71 to display the LCD DMX Configuration Window 3 Scroll down the page and select the Network configuration Link to display the Network Configuration Page shown below Configuring the Network The Network can be configured as follows e Node Name A unique identifier character string of up to eight characters This can be any name used to identify the node on the network
14. hting level at the point of installation The LCD backlight brightness can be set between 0 and 63 brightest 63 darkest The LCD can also be set to Off On or Flash by selected from the drop down menu default On Reconfiguring the DMX Ports The DMX Ports can be reconfigured on line by following the procedure previously described for Configuring the DMX Ports The SN110 software provides the facility to view the status of all Strand Nodes connected to the Ethernet Network by selecting Press here to view the network status from the LCD DMX page Node Name IP Type Mac Version Status On time Send Cb Evnt Err Ack Receive Cb Evnt Err Ack SN110 1 192 168 0 123 SN110 00 E0 01 00 1F 9E v2 5n On line 09 29 04 00000 00000 00000 00000 00000 00000 00000 00000 SN110 2 192 168 0 124 SN110 00 20 AF 5C DI AE v2 5n On line 09 29 04 00000 00000 00000 00000 00000 00000 00000 00000 SN110 3 192 168 0 125 SN110 00 E0 01 FF FF FC v2 5n On line 09 29 04 00000 00000 00000 00000 100000 00000 00000 00000 A MAIN 192 168 0 68 300 00 E0 01 23 45 56 v2 6 On line 09 29 04 00000 00000 00000 00000 100000 00000 00000 00000 AP BACKUP 192 168 0 69 300 00 E0 01 11 22 33 v2 6 On line 09 29 04 00000 00000 00000 00000 00000 00000 00000 00000 SN110 Nodes Installation Manual Sample Network Status Windo
15. nded for use as part of a lighting control system It must not be used for any other purpose where there is a risk of safety to persons The equipment contains power voltages There are no serviceable parts within the SN110 Node housing e Installation of the SN110 Node should be undertaken by a suitably qualified person 65110 Input Voltage Input Voltage Input Current Inrush Current 65111 Input Voltage Input Current Input Frequency Inrush Current 75785 6 Input Voltage Input Current Inrush Current 48V DC supplied as Power Over Ethernet Alternative nominal 24V 12 48V DC local supply 0 1 Amps max 48V DC 1 2 Amps max 110 240V AC 0 5 Amps 47 63Hz 20A 110V AC Max 40A 230V AC Max 24V DC 0 2 Amps 1 2 Amps Max Page 3 Installation Fitting the 65110 65111 Back Boxes Remove two M3 x 8 Screws Fix Facia to Back Box 2 Screws Fix Facia to Wall 4 Screws SN110 Nodes Installation Manual The 65110 and 65111 nodes are housed within a metal back box suitable for surface or flush wall mounting These models are intended for permanent wall mounted installation using earthed conduit to carry the power and network cables The unit should not be operated without the earthed metal conduit as it may fail EMC compliance Surface Mountin 1 Remove the two M3 x8 screws from the underside of the plastic front panel and lift the front plate upwards and away from the back box Keep the s
16. ons et ou les mises jour de ce manuel veuillez s ll vous plait contacter le bureau de Strand Lighting le plus proche Manual Copyright 2002 Strand Lighting Limited All rights reserved Asia Strand Lighting Asia Ltd 20F Delta House 3 on Yin Street Shatin N T Hong Kong ROC Tel 008 522 757 3033 Fax 008 522 757 1767 Asia Strand Lighting Asia Ltd Room 2519 25 F Zao Fong World Trade Building 369 Jiang Su Road Shanghai 200050 P R C Tel 0086 21 524 01118 Ext 2519 Fax 0086 21 524 00060 England Strand Lighting Ltd Unit 3 Hammersmith Studios Yeldham Road Hammersmith London W6 8JF Tel 0208 735 9790 Fax 0208 735 9790 Scotland Strand Lighting Ltd Mitchelston Industrial Estate Kirkcaldy Fife KY1 3LY Tel 01592 652333 Fax 01592 653528 Canada Strand Lighting Ltd 2430 Lucknow Drive 15 Mississauga Ontario L5S 1V3 Tel 001 905 677 7130 Fax 001 905 677 6859 Germany Strand Ligthting GMBH Ullsteinstrasse 114 142 12109 Berlin Tel 00 49 30 707 9510 Fax 00 49 30 707 95199 Italy Strand Lighting Italia S r l Via delle Gardenie 33 00040 Pomezia Roma Tel 00 39 06 919 631 Fax 00 39 06 914 7138 Russia Strand Lighting Ltd Novinsky Boulevard 20A Buildings 3 6 12069 Moscow Tel 007 095 234 4220 or 007 501 234 4220 Fax 007 095 234 4221 or 007 501 234 4221 USA Strand Lighting Inc 6603 Darin Way CYPRESS CA 90630 Tel 001 714 230 8200 Fax 001 714 899 0042 USA Strand Lighting Inc 928 Broadw
17. ounting in SLD Dimmer Rack Strand Part No 75600 The 65110 Node can be powered by 48V supplied as Power Over Ethernet PoE when Power Sourcing Equipment PSE is incorporated within the Ethernet Network When using PoE the node can be installed at any indoor position to suit the lighting requirements without the need for a power supply to be available at the node Alternatively when PoE is not incorporated in the Ethernet Network a local 24V DC supply can be provided adjacent to the node location The 65111 Node is provided with an integral 120 240V AC power supply used to provide the DC supply to the node The 65112 comprises the Node network board and the LCD board for mounting within OEM equipment Power to the boards can be provided by PoE The 75785 6 Node comprises the same main network board and LCD board as the 65110 Node however the boards are mounted in an open drawer chassis designed to slide into the SLD Dimmer Rack Processor Housing Power to the node is provided by the SLD integral power supply SN110 Node Model 75785 6 Page 2 Safety Warnings Electrical Supplies SN110 Nodes Installation Manual Avoid spillage from liquids If this occurs switch off immediately Protect from excessive dust or other contaminants For indoor use only This symbol means hazardous voltages are present The equipment is designed and manufactured to comply with international safety standards IEC950 UL1950 and CS 950 and is inte
18. ox taking care not to foul any components on the top or bottom lip of the back box 4 Screw the front plate to the back box or to the facia plate if the back box is flush mounted using the four M3 x 8 screws removed prior to installation of the back box 5 Fitthe plastic front panel and secure using the two M3 x 8 screws removed prior to installation of the back box 6 Switch on the 24V DC Supply 65111 Node The 65111 node is provided with an integral power supply which is connected locally to the 110 or 230V AC mains supply Fit the pre configured node to the back box as follows 1 Remove the green power PCB socket from the 110 240V universal power supply board and connect the live and neutral power cables to the connector Line Neutral imi PCB 2 Connect the mains earth to the earth stud on the back of the back box NOTE An earth continuity test is recommended 3 Plug the power socket into the power plug on the power supply board 4 A P Clip cable restraint is supplied alongside the power connector This cable restraint must be fitted to allow sufficient slack in the cable to allow the plug socket arrangement to connect without strain while preventing any pull on the power cable from dislodging the connector 5 Ensure the LCD cable is routed below the power supply board 6 Plug the ethernet cable into the RJ45 Ethernet Socket SK1 on the node main board Page 7 RJ45 Dual Connector RJ45 Connector Power Cable
19. tion see our web site or email technical support SN110 Nodes Installation Manual Press Submit to update the configuration then select LCD DMX configuration to display the LCD DMX Configuration page as shown below LCD DMX Configuration LCD Setting The intensity of the LCD backlight can be set to suit the lighting level at the point of installation Since this may not be known until after the node is installed the level can be left at the default level of 15 and adjusted after the node is installed The LCD can be set to Off On or Flash by selected from the drop down menu default On Configuring the DMX Ports The two DMX ports of the SN110 node can be configured as follows DMX Type The two DMX ports on the SN110 Node can be configured as DMX Out DMX In or Reporter by selecting the function from the drop down menu REPORTER DMX IN specifies that DMX data coming in on the specified Port should be placed on the network at the specified global network slot The first and last dimmers sent out from the incoming DMX frame are specified by the START and END numbers The START and END numbers must be between 1 and 512 DMX OUT specifies that DMX data coming in on the network at the specified global network channel offset will be sent out of the DMX Port The first and last dimmers sent out for the outgoing DMX frame are specified by the START and END numbers
20. ual e HTP Each NetSlot can be set to take preference when highest by selecting HTP from the drop down menu F HTP Having set up the LCD DMX Configuration press Submit to update the configuration 65110 Node PoE Power Supply When the 65110 Node is powered over the ethernet 48V DC is supplied to the node via the CAT5 network cable Fit the pre configured node to the back box as follows 1 Plug the ethernet cable into the RJ45 Ethernet Socket SK1 on the node main board 2 Fitthe node assembly into the back box taking care not to foul any components on the top or bottom lip of the back box 3 Screw the front plate to the back box or to the facia plate if the back box is flush mounted using the four M3 x 8 screws removed prior to installation of the back box 4 Fitthe plastic front panel and secure using the two M3 x 8 screws removed prior to installation of the back box 65110 Node Local 24V DC Supply The 65110 node can be powered from a local 24V DC supply instead of using power over the ethernet network Fit the pre configured node to the back box as follows 1 Plug the ethernet cable into the RJ45 Ethernet Socket SK1 on the node main board 2 Connect a Molex Type K 2 pin socket to the the end of the 24V DC cable and plug it into the 24V DC supply plug on the main board of the node noting that the ground pin is that which is closet to the reader in the adjacent picture 3 Fitthe node assembly into the back b
21. w Page 9 Installing New Software SN110 Nodes Installation Manual When updated SN110 software is available it can be downloaded from the Strand Lighting web site at www strandlighting com to a PC To install a new software version to an SN110 Node proceed as follows Place the SN110 Install File sn110 chk on the hard drive e g C tmp 1 2 Telnet onto SN110 3 Type usr bin mkspace sh then press Enter This command deletes files from the flash memory to make space for the new software The original factory default software is retained and is re installed automatically in the event of a failure to load the new software cl Telnet 192 168 11 123 Connect Edit Terminal Help uClinux command shell version 2 0 gt Jusr bin mkspace sh Stopping Node Now use ftp binary mode to copy install file to tmp sn110 chk After file has been copied run usr bin flashsw sh d ftp SN110 from file location e g C tmp Type binary to set up binary transfer ONO Type quit then press Enter Command Prompt Microsoft lt R gt Windows NT lt TM gt lt C gt Copyright 1985 1996 Microsoft Corp C tmp gt ftp 192 168 11 123 Connected to 192 168 11 123 220 SN110 ANONYMOUS ONLY FTP lt Version 6 mjr gt ready User lt 192 168 11 123 lt none gt gt ftp 331 Guest login ok access restrictions apply ftp gt binary 200 Type set to ftp gt put sn110 chk tmp sn110 chk 200 PORT command successful
Download Pdf Manuals
Related Search