Home

Biostar M7VIZ Owner's Manual

1. M7VIZ BIOS Setup Integrated Peripherals This submenu allows you to configure certain IDE hard drive options and Programmed Input Output features Power Management Setup This submenu allows you to configure the power management features PnP PCI Configurations This submenu allows you to configure certain Plug and Play and PCI options PC Health Status This submenu allows you to monitor the hardware of your system Frequency Voltage Control This submenu allows you to change CPU Vcore Voltage and CPU PCI clock However this function is strongly recommended not to use Not properly change the voltage and clock may cause the CPU or M B damage Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence These configurations are factory settings optimized for this system A confirmation message will be displayed before defaults are set Load Optimized Defaults V N N Set Supervisor Password Setting the supervisor password will prohibit everyone except the supervisor from making changes using the CMOS Setup Utility You will be prompted with to enter a password Enter Password M7VIZ BIOS Setup Set User Password If the Supervisor Password is not set then the User Password will function in the same way as the Supervisor Password If the Supervisor Password is set and the User Password is set t
2. If you highlight the literal Press Enter next to the Super IO Device label and then press the enter key it will take you a submenu with the following options Onboard FDC Controller Select Enabled if your system has a floppy disk controller FDC installed on the system board and you wish to use it If install and FDC or the system has no floppy drive select Disabled in this field The Choices Enabled default Disabled Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports The Choices Disabled 3F8 IRQ4 default 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Auto Onboard Serial Port 2 Select an address and corresponding interrupt for the first and second serial ports The Choices Disabled 2F8 IRQ3 default 3F8 IRQ4 3E8 IRQ4 2E8 IRQ3 Auto UART Mode Select This item allows you to determine which Infra Red IR function of onboard I O chip The Choices Normal default AS KIR IrDA RxD TxD Active This item allows you to determine which Infrared IR function of onboard I O chip The Choices Hi Lo default Hi Hi Lo Hi Lo Lo IR Transmission Delay This item allows you to enable disable IR transmission delay The Choices Enabled default Disabled 18 M7VIZ BIOS Setup UR2 Duplex Mode Select the value required by the IR device connected to the IR port Full duplex mode permits simultaneous two direction transmission Half duplex mod
3. ACPI Support Award ACPI BIOS support Version 1 0 of Advanced Configuration and Power interface specification ACPI It provides ASL code for power management and device configuration capabilities as defined in the ACPI specification developed by Microsoft Intel and Toshiba M7VIZ BIOS Setup PCI Bus Support This AWARD BIOS also supports Version 2 1 of the Intel PCI Peripheral Component Interconnect local bus specification DRAM Support DDR SDRAM Double Data Rate Synchronous DRAM are supported Supported CPUs This AWARD BIOS supports the AMD CPU Using Setup In general you use the arrow keys to highlight items press lt Enter gt to select use the lt PgUp gt and lt PgDn gt keys to change entries press lt F1 gt for help and press lt Esc gt to quit The following table provides more detail about how to navigate in the Setup program by using the keyboard Keystroke Function Up arrow Move to previous item Down arrow Move to next item Left arrow Move to the item on the left menu bar Right arrow Move to the item on the right menu bar Move Enter Move to the item you desired PgUp key Increase the numeric value or make changes PgDnkey Decrease the numeric value or make changes Key Increase the numeric value or make changes Key Decrease the numeric value or make changes Esc key Main Menu Quit and not save changes into CMOS Status Page Setup Menu
4. I Pin 1 2 Close Clear CMOS Data Pin 2 3 Close Clear CMOS Procedures 1 Remov e AC power line 2 Setthe jumper to Pin 2 3 Close 3 Wat for fiv e seconds 4 Setthe jumper to Pin 1 2 Close 5 Power on the AC 6 Reset y our desired password or clear the CMOS data Case Open Connector JCI1 Tel eet ba Case Open Signal 2 om Serial ATA Connector JS ATA1 JS ATA2 Only support with South Bridge VT8237 wsaravusate 7 Gouna CD ROM Audio In Header JCDIN1 Pin Assignment 1 Left Channel Input 2 Ground Perd o3 Ground 4 Right Channel Input 12 M7VIZ Front Panel Audio Header JF AUDIO1 21200 26014 Je26O6996 13 JF AUDIO Mic In Center Assignment Ground Right Line Out Speaker Out Ri i Right Ke y Left Line Out Speaker Out Left Line Out Speaker Out Left Left Right Line In Rear Speaker ES E Line In Rear Speaker Right Right Left Line In Rear Speer Leff 14 Left Line In Rear Speaker Left Digital Audio C nector JS PDIF1 Optiond for version 8 0 Pin Assignment EA ew l 2 SPDFOUT 3 Ground Wake On LAN Header JWO L1 Nosupport for version 8 0 Pin Assignment ES 3 ee 2 Gan Wort ts wem Front USB Header JUSB2 JUS B1 gt only support with South Bridge VT8237 Note Version 8 0 supports both JUSB 1 amp JUSB2 Pin Assignment Pin Assignment ERU testes rr mun
5. 23 M7VIZ BIOS Setup PowerOn by PCI Card When you select Enabled a PME signal from PCI card returns the system to Full ON state The Choices Disabled default Enabled Wake Up On LAN Ring To use this function you need a LAN add on card which support power on function It should also support the wake up on LAN jump Disabled default Wake up on LAN Ring not supported Enabled Wake up on LAN Ring supported RTC Alarm Resume When Enabled you can set the date and time at which the RTC real time clock alarm awakens the system from Suspend mode The Choices Enabled Disabled default IRQs Activity Monitoring Press Enter to access another sub menu used to configure the different wake up events i e wake on LPT amp COMM activity Primary INTR On IRQ3 COM2 Enabled IRQ4 COM1 Enabled IRQS LPT2 Enabled IRQ6 Floppy Disk Enabled IRQ7 LPT 1 Enabled IRQ8 RTC Alarm Disabled IRQ9 IRQ2 Redir Disabled IRQ10 Reserved Disabled IRQII Reserved Disabled IRQ12 PS 2 Mouse Enabled IRQ13 Coprocessor Enabled IRQ14 Hard Disk Enabled IRQI5 Reserved Disabled 24 M7VIZ BIOS Setup 7 PnP PCI Configurations This section describes configuring the PCI bus system PCI or Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components This section covers some very technic
6. Disabled default Enabled 14 M7VIZ BIOS Setup CPU amp PCI Bus Control If you highlight the literal Press Enter next to the CPU amp PCI Bus Control label and then press the enter key it will take you a submenu with the following options PCI Master 0 WS Write When enabled writes to the PCI bus are executed with zero wait states The Choices Enabled default Disabled PCD Master 0 WS Write When enabled writes to the AGP bus are executed with zero wait states The Choices Enabled default Disabled PCII Post Write When Enabled CPU writes are allowed to post on the PCI bus The Choices Enabled default Disabled PCD Post Write When Enabled CPU writes are allowed to post on the AGP bus The Choices Enabled default Disabled VLink 8X Support This item allows you to enable or disable VLink 8X support The Choices Enabled default Disabled PCI Delay Transaction The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification The Choices Enabled default Disabled Memory Hole When enabled you can reserve an area of system memory for ISA adapter ROM When this area is reserved it cannot be cached Refer to the user documentation of the peripheral you are installing for more information The Choices Disabled default 15M 16M System BIOS Cacheable Selecting the Enabled opti
7. eoo Effectuez une sauvegarde des fichiers deg Un message s affiche indquant que lal V rifiez l quipement du syst me Eoniguaton n est pas valide ou oul y a une Assurez vous que les informations de lq YA Impossble de r initidiser le syst me apr s R glez les cavalers maitre esclava l installaion d un deuxi me disque dur correctement Ex cutez le progamme SETUP e s lectionnez les types de lecteur Contacteq les fabrican5 pour toute question de 19 M7VIZ WarpSpeeder Introduction WarpSpeeder a new power ul control utility features three userfriendly functions including Ov erclock Manager Ov ervoltage Manager and Hardware Monitor With the Ov erclok Manager users can easily adjust the frequency they prefer orthey can get the best CPU perf ormance with just one click The Ov ervoltage Manager on the other hand helps to power up CPU core voltage and Memory voltage The cool Hardware Monitor smartly indicates the temperatures voltage and CPU fan speed as well as the chipset irf ormation Also in the About panel you can get detail descriptions about BIOS model and chipsets In addition the frequency status of CPU memory AGP and PCI along with the CPU speed are synchronically shown on our main panel Moreov er to protect users computer systems if the setting is nd appropriate when testing and results in system fail or hang WarpSpeeder technology assures the syste
8. 1010009001 a us amp a Us Pin Pin EH EN 3 Mic Power Bass 4 Audio Power ES KEY 5 USB USB Ee 13 M7VIZ Front 1394 Header J1394B1 Pin Assignment Pin sl a 3 Gun a com 5 8 6 P 8 av DRE KEY 14 M7VIZ Back Panel Connectors For version 1 3 ISL AN IBI TENTI pas DH LAN Whiua kam Prad Bee Le COMI COM Fake Kor KE ia LITE For version 8 0 Isi IST IU SHE ATI Peg Main Falli y Ss e Bm Sn GUMMI COME Ks kazi Koi Mat IR 15 M7VIZ Trouble Shooting No power to the system at al Power light don t Make sure power cable issecurely pugged in illuminate fan inside power supply does not turn on Indicator light on keyboard does notturn on Ge calle Contact techrica support PROBABLE SOLUTION System inoperative Keyboard lights are on Using even pressure on both ends of thd power indicator Ights are lit hard drive is DIMM press down firmly until the module spinning snaps into place PROBABLE SOLUTION System does not boot from hard disk drive can Check cable unning from disk to diskcontrolle be booted from CD ROM drive board Make sure both ends are securel plugged in check the drive type in the standard CMOS setup Backing up the hard drive is extremel important Al hard d amp ks are capable o System only boots from CD ROM Hard disk can Backup dataand application
9. 33 AM 22 M7VIZ This utiliy is responsible for conveniently invoking WarpSpeeder Utility Youcan use the mouse by clicking the left buttonin orderto inv oke WarpSpeeder M directly from the little tray icon oryou can right click the little tray icon to pop up apopup menu as following figure The Laurch Utility item in the popup menu has the same function as mouse left click on tray icon and Exit item will close Tray Icon utility if selected Lanuch Utility Exit iR NAT SCH tee eee a 2 Main Panel If you click the tray icon WarpSpeeder utility will be inv oked Please ref er do the following figure the utility s first windowy ou wil see is Main Panel Main Panel contains features as follows a Display the CPU Speed CPU external clock Memory clock AGP clock and PCI clock inf ormation b Contains About Voltage Overclock and Hardware Monitor Buttons for invoking respective panels c With a userfriendy Status Animation it can represert 3 overclock percentage stages Man walking gt overclock percentagefrom 100 110 Panther running gt overclock percentage from 110 120 Car racing gt overclock percentagef rom 120 above 23 Herdesre Motor Butiy E Volks Butinr 3 Voltage Panel Click the Voltage button in Main Panel the button wil be highlighted and the Voltage Panel wil slide ou to up asthefollowing figure In this panel you can decide to increas
10. Day automatically changes when you set the date Time hh mm ss Set the system internal clock IDE Primary Master Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Primary Slave Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Secondary Master Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Secondary Slave Options are in its sub Press lt Enter gt to enter the menu sub menu of detailed options Drive A 360K 5 25 in Select the type of floppy Drive B 1 2M 5 25 in disk drive installed in your system 720K 3 5 in 1 44M 3 5 in 2 88M 3 5 in None Video EGA VGA Select the default video CGA 40 device CGA 80 MONO M7VIZ BIOS Setup Item Options Description Halt On All Errors Select the situation in which No Errors you want the BIOS to stop Base Memory All but Keyboard All but Diskette All but Disk Key N A the POST process and notify you Displays the amount of conventional memory detected during boot up Extended Memory N A Displays the amount of extended memory detected during boot up Total Memory N A Displays the total memory available in the system M7VIZ BIOS Setup 3 Advanced BIOS Features W Figure 3 Advanced BIOS Setup Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Fe
11. FDD Cable X 1 User s Manual X 1 Fully Setup Driver CD X 1 USB 2 0 Cable X 1 optional S PDIF ou Cable X1 optional Rear I O Panelf or Mcro ATXCase X1 optional IEEE 1394 Cable X1 optional nonefor Version 8 0 M7VIZ How to set up Jumper The illustration shows to how set up jumper When the Jumper capis placed on pins the jumper is close If no jumper cap is placed on the pins the jumper is open The illustration shows a 3 pin jumper whose piniand 2 are lose when jumper cap is placed on these2 pins Jumper open Jumper close Pin1 2 close CPU Installation Step1 Pull the lever sideway s away from thesocket and then raise the lev er upto a 90 degree angle Step2 Lookf orthe white dd cut edge The white dot cut edge should point wards the lev er piv ot The CPU willfit only inthe correct orientaion Step3 Hold the CPU downfimly and then close the lever to complete the installdion Step4 Put the CPU Fan onthe CPU and buckle it Connect the CPU fan power cable to the JCFAN1 This completes the installation M7VIZ CPU Fan Header JCFAN1 Pm Assignment Ground 12V JCFAN1 3 FAN RPM rate Sense System Fan Header JSFAN1 ees T meer ES Gon ab oa tev 12V ES FAN RPM rate Sense DDR DIMM Modules DDR1 DDR2 DRAM Access Time 2 5V Unbuffered Registered DDR 200 MHz PC1600 DDR 266 MHz PC2100 DDR 333 MHz PC2700 Ty perequired DRAM Ty pe 64MB 128MB 256
12. Help Optimized Defaults CPU Clock This item allows you to select CPU Clock and CPU over clocking If unfortunately the system s frequency that you are selected is AN not functioning there are two methods of booting up the system Method 1 Clear the COMS data by setting the JCOMS1 2 3 closed as ON status All the CMOS data will be loaded as defaults setting Press the lt Insert gt key and Power button simultaneously after that keep on pressi the lt Insert gt key until the power on screen showed This action will boot up the system according to FSB of the processor X It s strongly recommended to set CPU Vcore and clock in default setting If the CPU Vcore and clock are not in default setting it may cause CPU or M B damage Method 2 30
13. 12 12V PIN ETS 2 3 Ground 13 Ground 4 owy 14 So 5 Ground 15 Ground 6 ES L 10 20 XX NX ROI 1 Misesessese JATXPWR1 5V 16 Ground Ground 17 Ground PW_OK 18 5V Standby Voltage 19 5V 5V 12V 20 5V 10 M7VIZ Power Source Selection for Keyboard Mouse JKBV1 No support for version 8 0 JKBV1 Assignment Description 310 1 Pin 1 2 close 5V f or key board and mouse PS 2 Mouse andPS 2 Key board are 5V Standby powered with 45V standby voltage Voltage Note In orderto support the function power on the system via keyboard and mouse function JKBV1 jumper cap should be placed on pin 2 3 Power S ource Selection for US B JUS BV1 JUSBV2 JUS BV3 No support for version 8 0 JUSBV1 JUSBV2 Description JUSBV3 e oio JUSBV3 5V for USB at the 1394 USB port connector Pin 1 2 close JUSBV2 5V for USB at the JUSB2 port connector JUSBV1 5V for USB at the JUSBLAN1 port connector 1 eio C 5V Standby JUSBV3 J1394 USB1 port is powered with standby voltage d 5V Pin 2 3 close HSE JUSB2 port is powered with standby voltage of JUSBV1 JUSBLAN 1 port is powered Note In orderto support the function power on the system via USB devices function JUSBV1 JUSBV2 JUSBV3 jumper cap shauld be placed on pin 2 3 respectively 11 M7VIZ Clear CMOS Jumper JCMOS1 JCMOS1 Assigoment 310 Normal Operation defauit
14. 133 Bus Master Mode LAN PHY E Chip VIA VT6103 E Supports 10 Mb s and 100 Mb s auto negotiation E Hat Full duplex capability IEEE 1394 Chip Optional for Version 1 3 None for Version 8 0 E Chip VIA VT6307 E Supports 2IEEE 1394 ports E Detects connected dev ice ty pes and automatically configure dataspeed to 100 200 or 400 Mbps On Board AC 97 Sound Codec Chip CMI9761A E Compliant with AC 97 specification E Supports 6channes M7VIZ On Board Peripherals a Rearside E 1 serial pot E 1 VGA port E 4 parallel port SPPEPP ECP mode E Audio ports in vertical position E 1 RJ 45 LAN jack E PS 2 mouse and PS 2 keyboard E 2 USB2 0 ports 4USB2 0 ports only support with South Bridge VT8237 E 1 1394A Firewire ports Optional for Version 1 3 none for Version 8 0 b FrontSide E 1 floppy port suppots 2 FDDs with 360K 720K 1 2M 1 44M and 2 88Mbytes E 4 USB2 0 ports E 1 front audio header E 1 S PDIF out header E 1 1394A Firewire ports Optional for Version 1 3 none for version 8 0 Dimensions E ATX Form Factor 22 1 X 24 5cm W XL forversion 1 3 19 4 X 24 4cm W XL forversion 8 0 B BIOS amp Software BIOS Award legal BIOS Supports APM1 2 Supports ACPI Supports USB Fundion Software Supports Warpspeeder 9th Touch FLASHER Qf ers thehighest performarce for Windows 98 SE Windows 2000 Windows Me Windows XP SCOUNIX etc Package contents HDD Cable X 1
15. Gate A20 Typematic Rate Settin When a key is held down the keystroke will repeat at a rate determined by the keyboard controller When enabled the typematic rate and typematic delay can be configured Disabled default Enabled Type matic Rate Chars Sec Sets the rate at which a keystroke is repeated when you hold the key down The Choices 6 default 8 10 12 15 20 24 30 Typematic Delay Msec Sets the delay time after the key is held down before it begins to repeat the keystroke The Choices 250 default 500 750 1000 Security Option This option will enable only individuals with passwords to bring the system online and or to use the CMOS Setup Utility System A password is required for the system to boot and is also required to access the Setup Utility Setup default A password is required to access the Setup Utility only This will only apply if passwords are set from the Setup main menu MPS Version Control For OS The BIOS supports version 1 1 and 1 4 of the Intel multiprocessor specification Select version supported by the operation system running on this computer The Choices 1 4 default 1 1 OS Select For DRAM gt 64MB A choice other than Non OS2 is only used for OS2 systems with memory exceeding 64MB The Choices Non OS2 default OS2 Summary Screen Show This item allows you to enable disable display the Summary Screen Show The Choices Disabled default Enabled 11 M7
16. ITE CHE PCI 1 FOO Trei Fan pins X CHR EE RARELY NOTE represents thefirst pin M7VIZ Component Index Version 8 0 c rommoom Back Panel Conrectors CPU Fan Connector JCFAN 1 ATX Power Conrector JATXP WER1 North Bridge FanConnecta JNFAN1 CD ROM Audio h Header JCDIN1 Front Audio Header JF AUDIO 1 Accelerated Graphics Port Slot AGP1 Digital Audio Comector JSPDIF 1 PCI BUS Slots PCI 1 3 Communic ation Networ k Riser Slot CNR1 optional Um D oue rx FloppyDisk Comector FDD1 Case Open Conrector JCI1 Front Panel Connector JPANEL1 SystemFAN Header JSFAN1 Front USB Headers JUSB1 amp JUS B2 IDE Connectors IDE1 2 Frequency Selection JCLK1 DDR Modules DDR1 2 Clear CMOS Furction JCMOS 1 M7VIZ English M7VIZ Features A Hardware CPU E Provides Socket A I Supports single AMD Athlon Duron Family processor E Front Side Bus at 200 266333 MHz CH orth Bridge VIA KM400 E South Bridge VIA VT8235C E VT8237 optional ain Memory Supports up to 2 DDR device E Supports SPD DDR 200 266 333 400 MHz without ECC DDR devices E Maximum memory size is 2GB Super I O E Chip Winbond W83697HF Version 1 3 ITE8705F Version 8 0 Slots E Three 32 bit PCI bus masterslots E One CNR slot only Ty pe B E One AGP 8X slot On Board IDE E Supports four IDE disk drives E Supports RO Mode 4 Master Mode and Ultra DMA 33 66 100
17. M7VIZ FCC Information and Copyright This equipment has beentested and found to comply with the limits ofa Class B digital device pursuant to Part 15 ofthe FCC Rules T hese limits are designed to provide reasonable protection against harmful interference ina residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications There is no guarantee that interference will not occur in a particular installation The vendor makes no representations or warranties with respect to the contents here of and specially disclaims any implied warranties of merchantability or fitness for any purpose Further the vendor reserves the right to revise this publication and to make changes to the contents here of without obligation to notify any party beforehand Duplication of this publication in part or in whole is not allowed without first obtaining the vendors approval in writing The content ofthis user s manualis subject to be changed without notice and we wll not be responsible for any mistakes found in this user s manual All the brand and product names are trademarks of their respective companies Conient Layout of M7 VIZ Version 1 3 ccccsccccsssssscccsscccccscsssecsssssecsssssoses 1 Component Index Version 1 3 eee e eese ee eene ee eee eee to enun 2 Lay
18. MB 512MB 1GB DIMM Module 184 pin DIMM Socket DDR Module Total Memory Location Size MB DDR 1 64MB 128MB 256MB 512MB 1GB 1 Max is DDR 2 64MB 128MB 256MB 512MB 1GB 2GB A Only for reference Installing DDR Module e vm 1 Unlocka DIMM slot by pressing the retaining clips Deg og outward Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot gor 2 Insert the DIMMverticaly and fimly into the slot nl until the retaining chip snap back in place and the DIMM is propery seated M7VIZ Jumpers Headers Connectors amp Slots Floppy Disk Comector FDD1 The motherboard provides a standardfloppy disk connector tha suppots 360K 720K 1 2M 1 44M and 2 88M floppy disk types This connedor supports the prov idedfloppy drive ribbon cables Hard Disk Connectors IDE1 IDE2 The motherboard has a 32 bit Enhanced PCI IDE Controller that provides PIO Mode 0 5 Bus Master and Ultra DMA 33 66 100 133 functionality It has two HDD connectors IDE1 primary and IDE2 secondary The IDE connectors can connect a master and a slave drive soyou can connect up to four hard disk drives The first hard drive should always be connected to IDE1 Peripheral Component Interconnect Slots PCI 1 3 This motherboard is equipped with 3 standard PCI slots PCI stands for Peripheral Component Interconnect and it is a bus standard for expansion cards This PCI slot is designated as 32 bit
19. T CHAJ i d AAEL 7 NOTE represents thefirstpin M7VIZ Component Index Version 1 3 cA os A ATX Power Conrector JATXP WR1 O FloppyDiskComector FDD1 B Power Source Sdection for Keyboard and P Front Panel Connector JPANEL1 Mouse JKBV1 C Power Source Sdection for USB JUSBV3 Q SystemFAN Header JSFAN1 D Back Panel Conrector R Audio DJ JDJ1 E Case Open Conrector JCI1 S Serial ATA C onrector JSATA1 2 F Front 1394 Header J1394B1 T Front USB Header JUSB1 G Accelerated Graphics Port Slot AGP1 U Front USB Heacer JUSB2 H PCI BUS Slots PC 1 3 V Power Source Sdection for USB JUSBV 2 L Front Audio Header JF AUDIO 1 W Clear CMOS Furction JCMOS 1 J Digital Audio Comector JSPDIF 1 X IDE Connectors IDE1 2 K CD ROM Audio h Header JCDIN1 Y DDR Modules DDR1 2 L Communication NetworkRiser Slot CNR1 Z CPU Fan Connector JCFAN1 M CNR Codec Onboard Selection Al Frequency Selection JCLK1 JCODECSEL1 N Wake On LAN Header JWOL1 B1 Power Source Sdection for USB JUSBV 1 optional only support with South Bridge VT8237 M7VIZ Layout of M7VIZ Version 8 0 CuO qa TR FAN CMOS 1a Socket A CPU pem BATI JUS Cptions JD JPRNTI JATXEWER SOLA ar 2E 1 a JNFANT p ptiseua LAN PH EDINI vT8103 314 SH hys 1 AGP JF AUDO IDE IDEI jussi P SCH m Codec ME Ju582 JSFOIF jpesanal ter nm Pc 1 S
20. VIZ BIOS Setup 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset mstalled on your system This chipset manage bus speeds and access to system memory resources such as DRAM It also coordinates communications with the PCI bus The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly W Figure 4 Advanced Chipset Setup gt DRAM Clock Drive Control Press Enter Item Help AGP amp P2P Bridge Control Press Enter gt CPU 8 PCI Bus Control Press Enter Menu Level Memory Hole Disabled System BIOS Cacheable Disabled Video RAM Cacheable Disabled DRAM Clock Drive Control To control the Clock Drive If you highlight the literal Press Enter next to the DRAM Clock Drive Control label and then press the enter key it will take you a submenu with the following options DRAM Clock This item determines DRAM clock following 100MHz 133MHz 166MHz or By SPD The Choices 100MHZ 133MHz By SPD default 166MHz 12 M7VIZ BIOS Setup DRAM Timing This item determines DRAM clock timing follow SPD or not The Choices Auto By SPD default Manual Turbo Ultra DRAM CAS Latency When DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing The Choices 2 5 default 2 Bank Inte
21. al items and it is strongly recommended that only experienced users should make any changes to the default settings W Figure 7 PnP PCI Configurations 0 0 PNP OS Installed No Reset Configuration Data Disabled Resources Controlled By fiuto ESCD 1 jou are Play PCI VGA Palette Snoop Disabled Assign IRQ For VGA Enabled Assign IRQ For USB Enabled PNP OS Installed When set to YES BIOS will only initialize the PnP cards used for the boot sequence VGA IDE SCSI The rest of the cards will be initialized by the PnP operating system like Window 95 When set to NO BIOS will initialize all the PnP cards For non PnP operating systems DOS Netware this option must set to NO The Choices No default Yes Reset Configuration Data The system BIOS supports the PnP feature which requires the system to record which resources are assigned and protects resources from conflict Every peripheral device has a node which is called ESCD This node records which resources are assigned to it The system needs to record and update ESCD to the memory locations These locations 4K are reserved in the system BIOS If the Disabled default option is chosen the system s ESCD will update only when the new configuration varies from the last one If the Enabled 25 M7VIZ BIOS Setup option is chosen the system is forced to update ESCDs and then is automatically set to the Disabled mode T
22. am built into the ROM BIOS The Setup program allows users to modify the basic system configuration This special information is then stored in battery backed RAM so that it retains the Setup information when the power is tumed off The Award BIOS installed in your computer system s ROM Read Only Memory is a custom version of an industry standard BIOS This means that it supports Intel Pentium 4 processor input output system The BIOS provides critical low level support for standard devices such as disk drives and serial and parallel ports Adding important has customized the Award BIOS but nonstandard features such as virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system The rest of this manual is intended to guide you through the process of configuring your system using Setup Plug and Play Support These AWARD BIOS supports the Plug and Play Version 1 0A specification ESCD Extended System Configuration Data write is supported EPA Green PC Support This AWARD BIOS supports Version 1 03 of the EPA Green PC specification APM Support These AWARD BIOS supports Version 1 1 amp 1 2 of the Advanced Power Management APM specification Power management features are implemented via the System Management Interrupt SMI Sleep and Suspend power management modes are supported Power to the hard disk drives and video monitors can be managed by this AWARD BIOS
23. and Option Page Setup Menu Exit Current page and return to Main Menu F1 key General help on Setup navigation keys F5 key Load previous values from CMOS F7 key Load the optimized defaults F10 key Save all the CMOS changes and exit M7VIZ BIOS Setup 1 Main Menu Once you enter Award BIOS CMOS Setup Utility the Main Menu will appear on the screen The Main Menu allows you to select from several setup functions Use the arrow keys to select among the items and press lt Enter gt to accept and enter the sub menu JI WARNING The information about BIOS defaults on manual Figure 1 2 3 4 5 6 7 8 9 is just for reference please refer to the BIOS installed on board for update information Figure 1 Main Menu Standard CHOS Features Frequency Voltage Control Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save amp Exit Setup PnP PCI Configurations Exit Without Saving PC Health Status Upgrade BIOS Esc Quit F9 Menu in BIOS E Select Item F10 Save 8 Exit Setup Time Date Hard Disk Type Standard CMOS Features This submenu contains industry standard configurable options Advanced BIOS Features This submenu allows you to configure enhanced features of the BIOS Advanced Chipset Features This submenu allows you to configure special chipset features
24. annels Select Enabled to activate the first and or second IDE interface Select Disabled to deactivate an interface if you are going to install a primary and or secondary add in IDE interface The Choices Enabled default Disabled IDE Prefetch Mode The onboard IDE drive interfaces supports IDE prefetching for faster drive access If the interface does not support prefetching If you install a primary and or secondary add in IDE interface set this option to Disabled The Choices Enabled default Disabled 16 M7VIZ BIOS Setup IDE Primary Secondary Master Slave PIO The IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the IDE devices that the onboard IDE interface supports Modes 0 through 4 provides successively increased performance In Auto mode the system automatically determines the best mode for each device The Choices Auto default Mode Model Mode2 Mode3 Mode4 IDE Primary Secondary Master Slave UDMA Ultra DMA 100 functionality can be implemented if it is supported by the IDE hard drives in your system As well your operating environment requires a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If your hard drive and your system software both support Ultra DMA 100 select Auto to enable BIOS support The Choices Auto default Disabled IDE HDD Block Mode If your IDE hard drive supports block mode select E
25. atures gt Boot Seq 8 Floppy Setup Press Enter gt Cache 8 Shadow Setup Press Enter Virus Warning Disabled Menu Level Quick Power On Self Test Enabled Boot Up NumLock Status On Gate A20 Option Fast Typematic Rate Setting Disabled Security Option Setup MPS Version Control For 0SI 1 41 OS Select For DRAM gt 64MB Non 0S21 Summary Screen Show Disabled Tle Move Enter Select PU PD Value US Save ESC Exit F1 General Help F5 Previous Values optimized Defaults Boot Seq amp Floppy Setup This item allows you to setup boot seq amp Floppy First Second Third Boot Other Device These BIOS attempt to load the operating system from the devices in the sequence selected in these items The Choices Floppy LS120 HDD 0 SCSI CDROM HDD 1 HDD 2 HDD 3 ZIP 100 LAN Disabled Swap Floppy Drive For systems with two floppy drives this option allows you to swap logical drive assignments The Choices Disabled default Enabled Boot Up Floppy Seek Enabling this option will test the floppy drives to determine if they have 40 or 80 tracks Disabling this option reduces the time it takes to boot up The Choices Enabled default Disabled M7VIZ BIOS Setup Cache amp Shadow Setu This item allows you to setup cache amp shadow setup CPU Internal Cache Depending on the CPU chipset in use you may be able to mcrease memory access time with this option Enabled defaul
26. e permits transmission in one direction only at a time The Choices Half default Full Use IR Pins Consult your IR peripheral documentation to select the correct setting of the TxD and RxD signals The Choices IR Rx2Tx2 default RxD2 TxD2 Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I O Address The Choices 378 IRQ7 default 278 IRQ5 3BC IRQ7 Disabled Parallel Port Mode The default value is SPP The Choices SPP default Using Parallel port as Standard Printer Port EPP Using Parallel Port as Enhanced Parallel Port ECP Using Parallel port as Extended Capabilities Port ECP EPP Using Parallel port as ECP amp EPP mode EPP Mode Select Select EPP port type 1 7 or 1 9 The Choices EPP 1 7 default EPP 1 9 ECP Mode Use DMA Select a DMA Channel for the port The Choices 3 default 1 Game Port Address Game Port I O Address The Choices 201 default 209 Disabled Midi Port Address Midi Port Base I O Address The Choices 330 default 300 290 Disabled Midi Port IRQ This determines the IRQ in which the Midi Port can use The Choices 5 10 default 19 M7VIZ BIOS Setup Init Display First With systems that have multiple video cards this option determines whether the primary display uses a PCI Slot or an AGP Slot The Choices PCI Slot default AGP 20 M7VIZ BIOS Setup 6 Power Management Se
27. e CPU core voltage and Memory voltage or not The default setting is No If y ou want to get the best performance of overclocking we recommendy ou click the option Y es 24 M7VIZ 4 Overclock Panel Click the Ov ercloc button in Main Panel the button will be highlighted and the Overclock Panel wil slide ou to left as the following figure 25 kaaa T TT UT EL e ww Siren 3 d pS KRIER deg Wee W _ Recent Putter a coe FE Lan 1 px EEE ES vm AA hi H Eaton THE Bee att brio inst ave mm Overclock Panel contains the these features a 3MHz button 1MHz button 1MHz button and 3MHz button provide user the ability to doreal time overclock adjustment Warning Manually overclock is potentially dangerous especially when the overcbcking percentage is over 110 We strongly recommend you verify every speed you overclock by click the Verify button Or you can just click Auto overdock button and let WarpSpeeder automaticallygets the best result for you b Recovery Dialog button Pop up the following dialog Let user select a restoring way if system need to do afail safe reboot 26 M7VIZ Recovery Options Please select a recovery option that will decide what kind of restoring you want to do after system fail safe reboot Options Group C Restore to Hardware Default CPU Clock Value d Auto overcloc
28. e X1 Manuel de l utilisateur X1 CD compl d instalation des pilotes X 1 C ble USB2 0 X1 option C ble S PDIF X 1 option Panneau dE S arri re pour chassis ATX X 1 option Cable IEEE 1394 X1 option Version8 0 nonprise encharge 18 M7VIZ D pannage Pas dalimenta on au syst me Les voyants Assurez vous que le cable d alimenta on es lumineux ne s alument pas le ventilateur bien branch PROBLEME SOLUTION Le syst me ne foncionne pas Les voyants du En exer ant une pression uniforme sur leg clavier sont dlum s les voyants de deux extr mit s du DIMM poussezle module l alimertation aussi le disque dur tourne vers le bas jusqu ce quil s enclenche PROBL ME SOLUTION Le syst me ne ser initalise pas du disque dur V rifez le cable du dsque la carte d r initidisation possible depuis le lecteur contr leur de disque Assurez vous que leg CD ROM deux extr mit s sont bia branch s v rifie le type de lecteur dans la configuratio standard de CMOS ll est tr s important d effectuer deg sauvegardes du disque dur Les disques durg peuvent tomber en panne a n importe que Le syst me ne se r initidise que depuis le CD ROM Le disque dur peut tre lu et les donn es et d applica on Reformatez lq applications sont utilisable mais il est dsque dur R installez les applications et leg impossible d effectuer de r initalisa on depuisle donn es sauvegard es sur les dsques d
29. each mode individually When not disabled each of the ranges are from 1 mm to hr except for HDD Power Down which ranges from 1 min to 15 mi and disable HDD Power Down When enabled the hard disk drive will power down and after a set time of system inactivity All other devices remain active The Choices Disabled default 1 Min 2 Min 3 Min 4 Min 5 Min 6 Min 7 Min 8 Min 9 Min 10 Min 11 Min 12 Min 13 Min 14 Min 15Min Suspend Mode The item allows you to select the suspend type under ACPI operating system The Choices Disabled default Min 2 Min 4 Min 6 Min 8 Min 10 Min 20 Min 30 Min 40 Min 1 Hour Video Off Option This field determines when to activate the video off feature for monitor power management The Choices Suspend Off default Always on Video Off Method This option determines the manner in which the monitor is goes blank V H SYNC Blank default This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer Blank Screen This option only writes blanks to the video buffer 22 M7VIZ BIOS Setup DPMS Initial display power management signaling The Choices Stop Grant PwrOn Suspend Modem Use IRO This determines the IRQ which can be applied in MODEM use The Choices 3 default 4 5 7 9 10 11 NA Run VGABIOS if S3 Resume Choosing Enabled will make BIOS run VGA BIOS to in
30. ex complet Puce IEEE 1394 Option Version 8 0 non prise en charge E Puce VIAVT6307 E Prend en charge 2 ports IEEE 1394 E D tecte les p riph riques connect s et configure automatique la vitesse de transfert des donn es 100 200 ou 400 Mb s Codec son AC 97 int gr Puce CMI9761A Conf orme la sp ci ication AC 97 E Prend en charge 6 canaux 17 M7VIZ P riph riques int gr s a Fa arri re E 1 port s rie E 4 port VGA 1 port parall le mode SPP EPP EC P Ports audio en position verticale E 1 prise r seau RJ 45 E Souris et clavier PS2 E 2 ports USB2 0 4 ports USB2 0 uniquement avec le pont sud VT8237 E 1 port 1394A Firewire option Version 8 0 non prise encharge b Faceavant E 1 port pour lecteur de disquettes prenden charge deux lecteurs de disquettes avec 360K 720K 1 2M 1 44M et 2 88 Mo E 4 ports USB2 0 E 1 connecteur audio a ant E 1 connecteur S PDIF E 1 port 1394A Firewire option Version 8 0 non prise encharge Dimensions E Facteur deforme ATX 22 1 X24 5cm I X L 19 4 X24 4cm I XL Version 8 0 B BIOS et logiciel BIOS BIOS Award Prend en charge APM1 2 Prend en charge ACPI Prend en charge lafonction USB Logiciel Prend en charge Warpspeeder 9th Touch FLASHER fre la meilleure performance sous Windows 98 SE Windows 2000 Windows Me Windows XP SCO UNIXetc Contenu du carton Cable pour disque dur X1 Cable pour lecteur de disquett
31. he AGP amp P2P Bridge Control label and then press the enter key it will take you a submenu with the following options AGP Aperture Size Select the size of the Accelerated Graphics Port AGP aperture The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any translation The Choices 64M 256M 128M default 32M 16M 8M 4M AGP Mode This item allows you to select the AGP Mode The Choices 4X default 2X 1X AGP Driving Control By choosing Auto the system BIOS will the AGP output Buffer Drive strength P Ctrl by AGP Card By choosing Manual it allows user to set AGP output Buffer Drive strength P Ctrl by manual The Choices Auto default Manual AGP Driving Value While AGP driving control item set to Manual it allows user to set AGP driving The Choices DA default AGP Fast Write The Choices Enabled Disabled default AGP Master 1 WS Write When Enabled writes to the AGP Accelerated Graphics Port are executed with one wait states The Choices Disabled default Enabled AGP Master 1 WS Write When Enabled write to the AGP Accelerated Graphics Port are executed with one wait states The Choices Disabled default Enabled AGP Master 1 WS Read When Enabled read to the AGP Accelerated Graphics Port are executed with one wait states The Choices
32. he User will only be able to view configurations but will not be able to change them Enter Password Save amp Exit Setup Save all configuration changes to CMOS memory and exit setup Confirmation message will be displayed before proceeding SAVE to CHOS and EXIT Y N V Exit Without Saving Abandon all changes made during the current session and exit setup confirmation message will be displayed before proceeding Quit Without Saving Y N N Upgrade BIOS This submenu allows you to upgrade bios BIOS UPDATE UTILITY Y N N M7VIZ BIOS Setup 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories Each category includes no one or more than one setup items Use the arrow keys to highlight the item and then use the lt PgUp gt or lt PgDn gt keys to select the value you want in each item W Figure 2 Standard CMOS Setup Date mm dd yy Jun 10 2003 Time hh mm ss ile Sas Sy Menu Level gt IDE Primary Master IDE Primary Slave Change the day month IDE Secondary Master year and century IDE Secondary Slave Drive A 1 44M 3 5 in 1 Drive B None Video EGA VGA Halt On All But Keyboard M7VIZ BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu Item Options Description Date mm dd yy Set the system date Note that the
33. he above settings will be shown on the screen only if Manual is chosen for the resources controlled by function Legacy is the term which signifies that a resource is assigned to the ISA Bus and provides non PnP ISA add on cards PCI ISA PnP signifies that a resource is assigned to the PCI Bus or provides for ISA PnP add on cards and peripherals The Choices Disabled default Enabled Resources Controlled By By Choosing Auto ESCD default the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral By Choosing Manual the user will need to assign IRQ amp DMA for add on cards Be sure that there are no IRQ DMA and I O port conflicts IR Resources This submenu will allow you to assign each system interrupt a type depending on the type of device using the interrupt When you press the Press Enter tag you will be directed to a submenu that will allow you to configure the system interrupts This is only configurable when Resources Controlled By is set to Manual IRQ 3 assigned to PCI Device IRQ 4 assigned to PCI Device IRQ 5 assigned to PCI Device IRQ 7 assigned to PCI Device IRQ 9 assigned to PCI Device IRQ 10 assigned to PCI Device IRQ 11 assigned to PCI Device IRQ 12 assigned to PCI Device IRQ 14 assigned to PCI Device IRQ 15 assigned to PCI Device PCI VGA Palette Snoop Choose Disabled or Enabled Some graphic contr
34. itialize the VGA card when system wakes up from S3 state The system time is shortened if you disable the function but system will need AGP driver to initialize the card So if the AGP driver of the VGA card does not support the initialization feature the display may work abnormally or not function after S3 The Choices Auto Yes default No Soft Off by PW R BTTN Pressing the power button for more than 4 seconds forces the system to enter the Soft Off state when the system has hung The Choices Delay 4 Sec Instant Off default IRQ Event Activity Detect If you highlight the literal Press Enter next to the IRQ Event Activity Detect label and then press the enter key it will take you a submenu with the following options VGA When set to On any event occurring at a VGA Port will awaken a system which has been powered down The Choices Off default On LPT amp COM When this option is set to On any event occurring at a COM serial LPT printer port will awaken a system which has been powered down The Choices LPT COM default COM LPT NONE HDD amp FDD When this option is set to On any event occurring on a hard drive or a floppy drive will awaken a system which has been powered down The Choices On default Off PCI Master When set to On you need a LAN add on card which supports the power function It should also support the wake up on LAN jump The Choices Off default On
35. k button User can click this button and WarpSpeeder M will set the best and stable performance andfrequency automatically WarpSpeeder utility will execute a series of testing until systemfail Then system will dofail safe reboot by using Watchdog function After reboot the WarpSpeeder uility will restore to the hardware ddaul setting or load the verified best and stable frequency accordingto the Recovery Dialogs setting e Verify button User can click this button and WarpSpeeder will proceed a testingf or current frequency If the testing is ok then the currentfrequencg will be sa ed into system registry If the testing f ail system wil do a fail safe rebooting After rebod the WarpSpeeder utility will restore to the hardware default setting or load the verified best and stable frequency according to the Recovery Dialog s setting Note Because the testing programs invoked in Auto overclock and Verify include DirectDraw Drect3D and DirectShow tests the DirectX 8 1 or newer intime library is required And please make sure your display card s color depth is High color 16 bit or True color 24 32 bit that is required for Direct3D rendering 27 M7VIZ 5 Hardware Monitor Panel Click the Hardware Monitor button in Main Panel the button will be highlighted and the Hardware Monitor panel will slide ou to left as thef ollowing figure In this panel y oucan get the realtime status inf
36. lth Status W Figure 8 PC Health Status Menu Level Enabl HardWare Show HAN Monitor in POST Enabled Chassis Open Warning Disabled Previo e 0 ed De Current CPUI Temperature This field displays the current temperature ofthe CPU Current CPU FAN Speed This field displays the current speed of CPU fan Current SYS FAN Speed This field displays the current speed SYSTEM fan Shutdown Temperature This item allows you to set up the CPU shutdown Temperature This item only effective under Windows 98 ACPI mode The Choices Disabled default 60 C 140F 65 C 149F 70 C 158F 75 C 167F CPU Vcore 3 3V 5V 12 V 12V 5V 5VSB VBAT V Detect the system s voltage status automatically 28 M7VIZ BIOS Setup Show H W Monitor in POST If your computer contains a monitoring system it will show PC health status during POST stage The item offers several delay time for you to choose The Choices Enabled default Disabled Chassis Open Warning This item allows you to enable or disable Chassis Open Warning beep The Choices Disabled Default Enabled 29 M7VIZ BIOS Setup 9 Frequency Voltage Control m Figure 9 Frequency Voltage Control Phoenix AwardBIOS CHOS Setup Utility Frequency Voltage Control CPU Clock Item Help Menu Level gt Tle Move Enter Select PU PD Value F1 Save ESC Exit F5 Previous Values EE imi F1 General
37. m stability by automatically rebooting the computer and then restart to a speed that is either the original system speed or a suitable one System Requirement OS Support Windows 98 SE Windows Me Windows 2000 Windows XP DirectX DirectX 8 1 or above The Windows XP operating system includes DirectX 8 1 If you useWindows XP y oudo not need to insall DirectX 8 1 20 M7VIZ Installation 1 Execute the setup execution file and then the following didog will pop up Please click Next button andfollow the ddault procedure toinstall Wetton lo the Hristall feel Wlizaid loi a asp pees The instal bed waad voll mebl rp peser om put computer Tp ponina click Het 2 When you see the following dialog in setup procedure it means setup is completed If the Launch the WarpSpeeder Tray Utility checkbox is checked the Tray Icon utility and WarpSpeeder M utility will be automatically and immediately launched aftery ou click Finish button 21 M7VIZ tale wizasd Complete Setup bas fiihs miang el apo pesdet on your campie F Launch the Wain perder Tias Liu Usage The folowing figures are just only for reference the screen printed in this user manual will changeaccordingto your motherboard on hand WarpSpeeder includes 1 tray icon and 5 panels 1 Tray Icon Whenever the Tray Icon utility is launched it wil display alittle tray icon on the right side of Windows Taskbar iO V 11
38. nabled for automatic detection of the optimal number of block read writes per sector the drive can support The Choices Enabled default Disabled VIA OnChip PCI Device If you highlight the literal Press Enter next to the OnChip PCI Device label and then press the enter key it will take you a submenu with the following options USB2 0 Support This item allows you to enable or disable USB2 0 The Choices Enabled default Disabled VIA 3058 AC97 Audio This option allows you to control the onboard AC97 audio The Choices Auto default Disabled VIA 3068 MC97 Modem This option allows you to control the onboard MC97 modem The Choices Auto default Disabled VIA 3043 OnChip LAN This option allows you to control the onboard LAN The Choices Enabled default Disabled Onboard LAN Boot ROM This item allows you to enable or disable Onboard LAN Boot ROM The Choices Disabled default Enabled Onchip USB Controller Select Enabled if your system contains a Universal Serial Bus USB controller 17 M7VIZ BIOS Setup and you have USB peripherals The Choices All Enabled default All Disabled USB Keyboard Mouse Support This item allows you to enable or disable the USB Keyboard Mouse Legacy Support The Choices Disabled default Enabled 1394 Fire Wire This item allows you to enable or disable 1394 Fire Wire The Choices Enabled default Disabled Super IO Device
39. ollers which are not VGA compatible take the output from a VGA controller and map it to their display as a way to provide boot information and VGA compatibility However the color information coming from the VGA controller is drawn from the palette table inside the VGA controller to generate the proper colors and the graphic controller needs to know what is in the palette of the VGA controller To do this the non VGA graphic controller watches for the Write access to the VGA palette and registers the snoop data In PCI based systems where the VGA controller is on the PCI bus and a non VGA graphic controller is on an ISA bus the Write Access to the palette will not show up on the ISA bus if the PCI VGA controller responds to the Write 26 M7VIZ BIOS Setup In this case the PCI VGA controller should not respond to the Write it should only snoop the data and permit the access to be forwarded to the ISA bus The non VGA IS A graphic controller can then snoop the data on the ISA bus Unless you have the above situation you should disable this option Disabled default Disables the function Enabled Enables the function Assign IRQ For VGA This item allows the users to choose which IRQ to assign for the VGA The Choices Enabled default Disabled Assign IR For USB This item allows the users to choose which IRQ to assign for the USB The Choices Enabled default Disabled 27 M7VIZ BIOS Setup 8 PC Hea
40. on allows caching of the system BIOS ROM at F0000h FFFFFh which can improve system performance However any programs writing to this area of memory will cause conflicts and result in system errors The Choices Enabled Disabled default Video RAM Cacheable Enabling this option allows caching of the video RAM resultng in better system performance However if any program writes to this memory area a system error may result The Choices Enabled Disabled default 15 M7VIZ BIOS Setup 5 Integrated Peripherals W Figure 5 Integrated Peripherals VIA OnChip IDE Device VIA OnChip PCI Device SuperI0 Device Init Display First OnChip USB Controller USB Keyboard Support USB Mouse Support IDE HDD Block Mode Press Enter Press Enter Press Enter PCI Slot All Enabled Disabled Disabled Enabled Item Help Menu Level VIA OnChip IDE Device The chipset contains a PCI IDE interface with support for two IDE channels Select Enabled to activate the first and or second IDE interface If you install a primary and or secondary add in IDE interface select Disabled to deactivate an interface If you highlight the literal Press Enter next to the Onchip IDE Control label and then press the enter key it will take you a submenu with the following options OnChip IDE Channel 0 1 The motherboard chipset contains a PCI IDE interface with support for two IDE ch
41. ormation of y our system The information will be rd reshed w ery 1 second 6 Abou Panel Click the About button in Main Panel the buton will be highlighted and the About Panel will slide out to up as the following f gure In this panel youcan get model name and detail inf ormation in hints of all the chipset that are related to overclocking You can also get the mainboards BIOS model and the Version number d WarpSpeederTM utility 28 M7VIZ ai mo ttn Version 09 54 EG 12215 LI D h sall 5 za nail S Note Because the overclock oveivol age and hardware monitor features are controled by several separate chipset WarpSpeeder divide these features to separate panels F one chipset is not on board he correlative button in Main panel will be disabled but will not interfere other panels functions This property can make WarpSpeeder utility more robus 29 M7VIZ 05 28 2004 30 M7VIZ BIOS Setup DIU NET M Mam Menus i dotes etr RU ee desque is 3 2 Standard C MO S Features ste een einer me it te ger 6 Advanced BIOS Features i oiu c Bre S e d een tee 9 4 Advanced Chipset Features 12 5 Integrated Peripherals zh interne enter 16 6 Power Management Setup us 21 T PnP PCT Configurations to reper ERR ture 25 RE EE 28 9 Frequency Voltage Control us 30 M7VIZ BIOS Setup BIOS Setup Introduction This manual discussed Award Setup progr
42. out of M7 VIZ Version 8 0 msseeesmeneremeeeerenmeeense 3 M7VIZ Component Index Version 8 0 ccce eeeeeee 4 oC E EE 5 MIVIZ Peatuf eS acts nti edP bab ere ti 5 Paka SERA ARR ANT 6 How to set up JUIWpet iuc oe etn p nt nb set 7 CRU is aa EA Ta ce nu n e 7 DDR DIMM Modules DDR1 DDR2 8 Installing DDR M oduleas cepto nte nerd unies tueuse 8 Jumpers Headers Connectors amp Mots 9 Trouble S bouge eeh 16 IN me 17 Caract ristiques de la M7 VIZ esses 17 Contenu db dms RSS ne ne atom rte ox ces ees 18 RI E cer 19 Marpspeelle Essaie eto dina uode aso Pekan aha Case nea da ado Lar dea D EE Ea D 20 To trade Oft eee eee eer terne o aao trien no ao ere ee T ENEE ore a eere arae ee 20 System IRequiremmelib cocer di erro Ew A desee Elbe hedge t ru Teen 20 Installation EAE AMKA WIMA BA iet teles tse tta o en ast 21 UE EE 22 M7VIZ Layout of M7VIZ Version 1 3 omy He DEI PE amp e W al rr Serre Arsen CLAN jeux sourd oon LELEL Ce mt amj KAY 28i LISE YA et LGS a CPU be B PRT Tw Ki a ae TW un nt gt Winhoed Dad D LO YOAJ E 2 must RB e TAAL ANI E E BIOS Met IpE Hx i A J ALITIBCH KT Chip Mam BATI fist 1 oum IL ant LAN cg pu Dm db A JC Mod iy E E NT Ll p nri 1 pci o T pmi ous i Hlp E We me LENS bag as Ca FON Kell 7 LI n cJ de
43. rleave This item allows you to enable or disable the bank interleave feature The Choices Disabled default 2 bank 4 bank Precharge to Active Trp This items allows you to specify the delay from precharge command to activate command The Choices 2T 3T 4T 5T default Tras Non DDR 400 DDR 400 This item allows you to choose Non DDR 400 DDR 400 The Choices 6T 8T 7T 10T default 5T 6T 8T 12T Active to Precharge Tras This items allows you to specify the minimum bank active time The Choices 7T 6T default Active to CMD Tred Use this item to specify the delay from the activation of a bank to the time that a read or write command is accepted The Choices 2T 3T 4T 5T default DRAM Burst Length The Choices 4 default 8 DRAM Queue Depth This item permits to place the depths of the memory The deeper the depth is the better is this function The Choices 4 level default 2 level 3 level DRAM Command Rate This item controls clock cycle that must occur between the last valid write operation and the next command The Choices 1T Command 2T Command default Write Recovery Time This item allows you to select the recovery time The Choices 2T 3T default 13 M7VIZ BIOS Setup tWTR for DDR400 only This item allows you to choose tWTR for DDR 400 only The Choices 1T 2T 3T default AGP amp P2P Bridge Control If you highlight the literal Press Enter next to t
44. s Accelerated Graphics Port Slot AGPI Your monitor will attach directly to that video card This motherboard supports video cards for PCIslots but it is also equipped with an Accelerated Graphics Port AGP An AGP card will take advantage of AGP technology for improved v ideo efficiency and perfomance especially with 3D graphics Communication Network Riser Slot CNR1 The CNR specification is an open Industry Standard Architecture and it defines a hardware scalable riser card interf ace which supports modem only Serial ATA Connector JS ATA1 JS ATA2 only support with South Bridge VT8237 The motherboard has a PCI to SATA Controller with 2 channels SATA inter ace it satisfies the SATA 1 0 spec and can transfer data with 1 5 Gb s speed Note 1 When plugging SATA HDD on JSATAT connector SATA BIOS wil automatically detect as channel 1 2 When plugging SATA HDD on JSATA2 connector SATA BIOS wil automatically detect as channel 0 M7VIZ Front Panel Connector JPANELI Function EAE TM Function 5 Speaker Sleep Control Sleep Connector 4 Grand 6 NA NA Speaker A A V Speaker 8 Power LED POWER HDD LED HardDrve 10 Power LED LED HDD LED LED 12 Power LED Ground Reset Power Button Power on Reset Control Button Ground Button mm LI Jea w IDA IrDA 24 N N N N Power Connectors JATXP WRI Assignment PIN Assignment 3 3V 11 43 3V 3 3V
45. s files Reforma be read and applications can be used but the hard drive Re install applicatonsand data booting from hard disk is impossible using backup disks PROBABLE SOLUTION Screen message says Invalid Configuration on Review system s equipment Make sure CMOS Failure correct informa onis in setup PROBABLE SOLUTION Cannot boot system after installing secord hard drive Set master slave jumperscorrectly Run SETUP program and select correct drive manufacturers fo 16 M7VIZ Fran ais Caract ristiques de la M7 VIZ A Mat riel Processeur E Fournit unsupport Socket A E Prend en charge un unique processeur AMD de laf amille Athlon Duron D Bus f ace avant 200 266 333 MHz hipset Pont nord VIA KM400 E Pont sud VIA VT8235CE VT8237 option y moire principale Prend en charge 2 barrettes DDR E Prise en charge des p riph riques SPD DDR 200 266 333 400 MHz sans ECC E Taille maximale de m moire 2 Go Super E S E Puce Winbond W83697HF Version 1 3 ITE8705F Version 8 0 Expansion E Trois emplacements PCI 32 bits bus ma tre E Un emplacement CNR Ty pe B uniquement E Un emplacement AGP 8X IDEint gr Prend en charge quatre lecteurs de disques IDE E Prend en charge les modes HO 4 Maitre et bus maitre Ultra DMA 33 66 100 133 R seau E Puce VIAVT6103 E Prend en charge la n gociation automatique 10 Mb s et 100 Mb s E Capacit semi duple dupl
46. t Enable cache Disabled Disable cache External Cache This option enables or disables Level 2 secondary cache on the CPU which may improve performance Enabled default Enable cache Disabled Disable cache CPU L2 Cache ECC Checking This item allows you to enable disable CPU L2 Cache ECC Checking The Choices Enabled default Disabled Video BIOS Shadow Determines whether video BIOS will be copied to RAM for faster execution Enabled default Optional ROM is enabled Disabled Optional ROM is disabled Virus Warning This option allows you to choose the Virus Warning feature that is used to protect the IDE Hard Disk boot sector If this function is enabled and an attempt is made to write to the boot sector BIOS will display a warning message on the screen and sound an alarm beep Disabled default Virus protection is disabled Enabled Virus protection is activated Quick Power On Self Test Enabling this option will cause an abridged version of the Power On Self Test POST to execute after you power up the computer Enabled default Enable quick POST Disabled Normal POST Boot Up NumLock Status Selects the NumLock State after power on On default Numpad is number keys Off Numpad is arrow keys Gate A20 Option Select if chipset or keyboard controller should control Gate A20 Normal A pin in the keyboard controller 10 M7VIZ BIOS Setup controls Gate A20 Fast default Lets chipset control
47. tup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up power down features W Figure 6 Power Management Setup RCPI function Enabled ACPI Suspend Type S1 P0S 1 Power Management Option User Definel Menu Level HDD Power Down Disablel Suspend Mode Disablel Video Off Option Suspend gt Off Video Off Method H SYNC Blank MODEM Use IRQ 3 Run VGRBIOS if S3 Resume Yes Soft Off by PHRBTN Instant 0ff gt IRQ Event Activity Detect Press Enter Previo e 0 ed De ACPI function This item displays the status of the Advanced Configuration and Power Management ACPI The Choices Enabled default Disabled ACPI Suspend Type The item allows you to select the suspend type under the ACPI operating system The Choices S1 POS default Power on Suspend S3 STR Suspend to RAM S1483 POS STR Power Management This category allows you to select the type or degree of power saving and is directly related to the following modes 1 HDD Power Down 2 Suspend Mode There are four options of Power Management three of which have fixed mode settings 21 M7VIZ BIOS Setup Min Power Saving Minimum power management Suspend Mode 1 hr HDD Power Down 15 min Max Power Saving Maximum power management only available for sl CP Us Suspend Mode 1 min HDD Power Down 1 min User Define default Allows you to set

Biostar M7VIZ Owner's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents