Binatone 2300 User's Manual
Contents
1. Binatone Innovation you can afford USER GUIDE Concept Combo 2300 CORDED AND DIGITAL CORDLESS TELEPHONE UK BTP Ver 3 Dec 07 Before operating this set please read these instructions carefully Note This guide is for the corded part only For instructions on how to use the cordless part see the Combo 2300 Cordless Handset user guide Important note emergency calls The CC2300 cordless handset is not designed for making emergency calls when the mains power fails But if there s a power failure you can use the base unit telephone to make an Emergency Call by lifting up the corded handset instead of using the speakerphone Note After lifting the handset you will need to wait for several seconds to get dial tone before keying in the telephone number to make the call Also you cannot dial numbers from memories when the mains power is off Before operating this set please read these instructions carefully If you need help Binatone Helpline for UK only Monday to Friday from 9 00am to 5 00pm Tel 0845 345 9677 Please note that all calls are charged at local rate Or visit our website http www binatoneonline com Unpacking your CC2300 system In the box you will find W the base unit telephone W a telephone line cable for the base unit W a mains power adapter for the base unit E the cordless handset up to five depending on which CC2300 system you ve bou2. can t transfer a e call Make sure the other handset is in range of the base unit Make sure you are dialling the correct number for the other handset If the fault persists Disconnect all other instruments connected to the same line as the CC2300 and try to make a call Disconnect the base unit from the telephone line and plug a different phone into the master telephone socket Try making a call If this works the line is OK If the call does not work and you are using a two way socket adapter remove it and plug a telephone directly into the socket If the call now works the adapter may be faulty If you cannot make a call the fault may be on the exchange line Contact the service provider the BT engineers on 151 for UK only or your cable company If you still cannot identify the cause of the problem contact the Binatone on 0845 345 9677 UK only Binatone Help Line 0845 345 9677 30 ES Cleaning and care Do notclean any part of your CC2300 with benzene thinners or other solvent chemicals this may cause permanent damage which is not covered by the Guarantee When necessary clean it with a damp cloth Keep your CC2300 away from hot humid conditions or strong sunlight and don t let it get wet Every effort has been made to ensure high standards of reliability for your CC2300 However if something does go wrong please do not try to repair it yourself consult your supplier or
3. Binatone Help Line 0845 345 9677 12 e e o create a contact in your phoneboo The Phonebook can store up to 150 names maximum 12 characters and numbers maximum 20 digits in the memory Also you can select a different ringer melody for each entry but this will only work if you subscribe to CID see page 17 Press the MENU OK button to see PHONE BOOK Press the MENU OK button to see LIST Press the DOWN button to see NEW ENTRY Press the MENU OK button and the display will show a flashing bar at the beginning of the name position Key in the name using the digit keys maximum 12 characters If you make any mistakes press DELETE button to delete When you have finished press the MENU OK button to confirm and the display will move the flashing bar to the beginning of the number position Key in the number using the digit keys maximum 20 digits If you make any mistakes use the DELETE button to delete Press the MENU OK button to confirm and the display will show MELODY 1 Use the UP or DOWN buttons to scroll through the melodies there are 10 melodies to choose from Press the MENU OK button to confirm your selection You will hear a confirmation tone and the display will return to NEW ENTRY If there is no more space in the phonebook MEMORY FULL will appear on the display o delete a contact in your phonebook eB
4. in use A M e This will display if it is A M in the 12 hour AM clock mode PM P M e This is display if it is P M in the 12 hour clock mode Binatone Help Line 0845 345 9677 2 Page Where to find it 1 What s on the display 2 e What the symbols mean 2 Read First before Use 5 e Choosing a site for base unit and charger pod 5 e Mains power connection 5 e If you have a broadband line 5 Installation and Set up 6 e Choose a suitable site for the base unit 6 e Connect the mains power lead and the telephone line cord into the base unit 6 e Plug the main adaptor into your wall socket 6 e Connect the base unit to the telephone line 6 Desk Wall mount installation 7 e Desk Mount 7 e Wall Mount 7 Basic settings 9 e To set Date and Time 9 Making and answering calls 10 e To make call 10 e To make a call from redial list 10 e To make a call from caller display CID list 10 e To answer a call 10 e To Mute or un mute the microphone 11 e To change the earpiece or speakerphone volume during a call 11 e Emergency call without mains power 11 Memory Phonebook management 12 e To create a contact in your phonebook13 Binatone Help Line 0845 345 9677 Page e To delete a contact in the phonebook 13 To delete all contacts in your phonebook 14 e To edit a contact in your phonebook 14 e To store a last number redial in your phonebook 15 Making calls from the phonebook 16 e Reviewing phonebook memory status 16 e Direct
5. not wobble Place the Handset on the cradle with the parking hook on the cradle arranged to fit in the parking recess under the earpiece on the Handset Binatone Help Line 0845 345 9677 8 e Basic settings To set Date and Time Note If you subscribe to Caller Display see page 17 your SC3410 time and date settings will be automatically updated by the network when you receive an incoming call The Caller Display service only sends the month and date not the year so you may still need to set the year as this is used to calculate the day for the answering machine time stamp If the time and date are set on the cordless handset it will automatically be set on the base unit and vice versa The format for the date is YYYY MM DD and the time is HH MM in 12 hour format Press the MENU OK button a orv Then press the UP or DOWN button until SETTINGS is displayed a8 Then press the MENU OK to confirm The display will show DELETE HS Press the UP or DOWN button until DATE amp TIME is displayed TO Then press the MENU OK to confirm The year will be flashing 4 or Y Press the UP or DOWN button to set the year TO Press the MENU OK to confirm _ The month will be flashing 4 or v Press the UP or DOWN button to set the month o8 Press the MENU OK to confirm The date will be flashing Press the UP or DOWN button to set the date Press the MENU OK to confirm k __ The h
6. v Press the DOWN button to see DELETE ox Press the MENU OK button twice you will hear the completion tone and the display will return to the Caller ID list To delete all Caller ID records Repeat the steps above to review the CID list o B Press the MENU OK button to see ADD to PB v Press the DOWN button twice to see DELETE ALL o B Press the MENU OK button twice you will hear the completion tone and the display will show EMPTY To store a Caller ID contact in the phoneboo Repeat the steps above to review the CID list and to locate the record you want to store in the phonebook Press the MENU OK button to see ADD TO PB ox Press the MENU OK button to confirm and the display will show a flashing bar at es the beginning of the name position Ora T B gt Enter name using keypad x8 Press the MENU OK button to confirm the name The display will move the flashing bar to the end of the number position If the number needs modifying use the keypad to enter digits or the DELETE button to delete Press the MENU OK button to confirm the number and the display will show MELODY 1 Use the UP or DOWN buttons to scroll through the melodies Press the MENU OK button to confirm your selection You will hear a confirmation tone and the display will return to the CID list Binatone Help Line 0845 345 9677 18 Ringer volume melody To change ringer volume You can adjust
7. B iv ox Press the MENU OK button to see PHONE BOOK Press the MENU OK button to see LIST Press the DOWN button repeatedly until you see DEL RECORD Press the MENU OK button The display will show the first name and number in your phonebook Binatone Help Line 0845 345 9677 13 Gory ZO ZO Use the UP or DOWN buttons to scroll through the list until you see the contact you want to delete Press the MENU OK button and the display will show CONFIRM Press the MENU OK button to confirm if you really want to delete this entry or press the PHONEBOOK CANCEL to save the contact In either case the display will return to the previous menu option To delete all contacts in your phoneboo B v o8 Press the MENU OK button to see PHONE BOOK Press the MENU OK button to see LIST Press the DOWN button repeatedly until you see DELETE ALL Press the MENU OK button and the display will show CONFIRM Press the MENU OK to confirm or press the PHONEBOOK CANCEL button to save the contacts In either case the display will return to the previous menu option To edit a contact in your phoneboo o B ox Press the MENU OK button to see PHONE BOOK Press the MENU OK Press the DOWN button repeatedly until you see EDIT RECORD Press the MENU OK button and the display will show the first name and num
8. Press the MENU OK button to see PIN Key in the 4 digit PIN code for the base the CC2300 default PIN code is 0000 IIT a TI o Press the MENU OK button to confirm and the display will flash SEARCHING 1 or 2 3 4 Atthe same time on the base press the MENU OK button to see PHONEBOOK Ig N Awa 8 Press the UP button tweice to see REGISTRATION TIO 9 Press the MENU OK button to see SEARCHING flash on base display After a short delay if the registration is successful there will be a confirmation beep and the Handset display will go back to idle mode with number shown e g HS1 HS2 The base display will also go back to idle mode To de register a handset You may need to do this if you need to replace a faulty handset Call the Binatone help line if you need more advice e To de register a handset using the CC2300 base menu With the base in idle mode 1 Press the MENU OK button to see PHONEBOOK v 2 Press the DOWN button twice to see SETTINGS 3 Press the MENU OK button to see DELETE HS 4 Press the MENU OK button to see HS 1 or 2 3 4 Aud Press UP or DOWN button to select the handset you want to de register 5 Press the MENU OK button to confirm and the selected handset will be de registered The display on the handset that has been deleted will show UNREGISTERED m Press the PHONEBOOK BACK button to return to the previous menu at any time Not
9. also display the caller s name if the network sends it but this is not normally available in the UK New CID log If you receive a new call the display will show the NEW icon with the name and number of the caller If there are no items on the CID list the display will show NO CALLS The display may also show the following UNAVAILABLE if the number of the caller is unavailable e g from an international call WITHHELD if the call is from someone who has withheld their number e g by dialling 141 To review the CID list o8 Press the MENU OK button to see PHONEBOOK w Press the DOWN button to see CALL LOG Press the MENU OK button to see RECEIVED ok o B Press the MENU OK button to see the most recent record in the CID list 4 or v Press the UP or DOWN buttons to scroll through the CID list The NEW icon will be displayed in the idle screen until all new calls have been viewed in the CID list Note To go directly to the first record of the CID list press the UP or DOWN 4 orw z s buttons in standby mode f you wish to call directly from the CID list press the SPEAKERPHONE button or lift up the handset to dial the number automatically Binatone Help Line 0845 345 9677 17 E To delete a Caller ID record Repeat the steps above to review the CID list and to locate the record you want to delete Press the MENU OK button to see ADD to PB a8
10. button to confirm the setting s Press the PHONEBOOK CANCEL button to return to the previous menu Binatone Help Line 0845 345 9677 20 e Using a multi handset system o Make Intercom calls N Press the INTERCOM button If you have only one cordless handset registered INT to the base the display will show CALLING HS1 and the base will beep If you have more than one handset registered to the base the display will show HS with the registered handset numbers above and the base will output a continuous beep until you press the number for the handset you want to intercom Then the display will change for example to CALLING HS2 if itis handset 2 that is being called If you enter a number that is not available the base will return to idle mode If you do not enter any number for 1 minute the handset will return to idle mode The handset being called will ring with its selected melody and display BASE CALLING To cancel the intercom call press the INTERCOM button again Receiving an intercom call from a cordless handset the call by pressing the SPEAKERPHONE button or picking up the handset If you want to end the intercom press the SPEAKERPHONE button or yy When the phone rings and the display shows HS 1 CALLING you can answer o replace the handset To Transfer intercom call During a call it is possible to transfer a call to another handset During an external call if you want to tr
11. confirmation beeps The display will return to DIAL MODE e Press the PHONE BOOK BACK until you return to idle mode o Set Base to default settings This allows you to restore base settings to their default settings Ext Ringer Volume 5 Ext Ringer Melody 1 Int Ringer Volume 5 Int Ringer Melody 2 Dial Mode TONE Flash Time 100ms Key Tone ON Language ENGLISH PIN CODE 0000 The Caller Display CID and Redial lists will be erased but the Phonebook memories and TAM settings will remain unchanged EO Press the MENU OK scroll DOWN until you see SETTINGS iv a B wv Press the MENU OK then scroll DOWN until you see BS DEFAULT NT iz oS Press the MENU OK and the display will show PIN Enter the PIN code using the keypad Default PIN is 0000 kyan o E m Swan kie 2 Press the MENU OK and you will hear the confirmation beeps and the display will return to idle mode Binatone Help Line 0845 345 9677 27 ES To Change the PIN code Some functions including handset registration require a PIN code The default PIN is 0000 but you are able to change to your personal 4 digit PIN Press the MENU OK button Then scroll DOWN until you see SETTINGS Then press the MENU OK button Then scroll DOWN until you see MODIFY PIN Press the MENU OK button and the display will show PIN aes Enter the PIN code using the keypad
12. the telephone line otherwise you may get interference between the telephone and the broadband which could cause problems TELEPHONE WALL SOCKET MICROFILTER In a home with broadband every telephone must have a micro filter connected not just the one at the telephone point that your modem is connected to If you need more broadband micro filters contact your broadband supplier Binatone Help Line 0845 345 9677 5 E Installation and Set up 1 Choose a suitable site for the base unit see page 5 l 2 Connect the mains power lead and the telephone line cord into the base unit Plug one end of the telephone line cord into the jack on the back of the base the other end will plug into the telephone wall socket later See the note on page 5 3 Plug the mains adaptor into your wall socket If you have one or more charger pods plug the mains adaptors accordingly Make sure that the 230VAC 50hz mains socket is switched OFF when you plug the mains adapter into the socket ASN N See the note on page 5 4 Connect the base unit to the telephone line Insert the telephone line plug into the socket then switch mains power back ON o o Make sure the mains socket is switched on D the phone won t work without electrical power Binatone Help Line 0845 345 9677 6 Desk Wall mount installation Desk Mount To place the CC2300 on a desk connect t
13. the volume level of the intercom ringer INT RING and the external call ringer EXT RING independently with settings from 1 quietest to 5 loudest or turned OFF Press the MENU OK button Scroll DOWN until you see SETTINGS Then press the MENU OK button Scroll DOWN until you see RING SETUP Press the MENU OK button Then it will display INT RING or scroll DOWN to select EXT RING Press the MENU OK button The display will show MELODY Scroll DOWN until you see VOLUME Then press the MENU OK button to select and the display will show VOLUME 2 Press the UP or DOWN button to scroll through the volume settings from OFF 1 to 5 Then press the MENU OK button to confirm the setting Press the PHONEBOOK BACK button to return to the previous menu To change ringer melod There are 10 base ringer melodies from 1 to 10 ox Press the MENU OK button w Scroll DOWN until you see SETTINGS Binatone Help Line 0845 345 9677 19 Ea Then press the MENU OK button Scroll DOWN until yiu see RING SETUP Press the MENU OK button Then it will display INT RING or scroll DOWN to select EXT RING Press the MENU OK button The display will show MELODY Then press the MENU OK button to select and the display will show MELODY 1 Press the UP or DOWN button to scroll through the Melody list from 1 to 10 B Then press the MENU OK
14. Memory Call 16 e To Store the telephone number 16 e To Speed Dial the telephone number 16 Caller Display CDS Caller ID CID 17 e NewCID log 17 e To review the CID list 17 e To delete a Caller ID record 18 e To delete all Caller ID records 18 e To Store a Caller ID contact in phonebook 18 Ringer volume and melody 19 e To change ringer volume 19 Using multi handset 1 21 e To make intercom calls 21 e To Transfer intercom call 21 e To set up a three way conference 22 SOS call function 25 e How SOS call functipn works 25 e How to terminate SOS call function 25 e To Set SOS number 25 3 e Advanced use of your Phone 26 e To Turn key tones on off 26 e To Set flash Recall time 26 e To Set Dialling Mode Tone Pulse 27 e To Set Base to default settings 27 e To Change the PIN code 28 Troubleshooting 29 Cleaning and Care 31 Declaration of Conformity 31 Guarantee and Service 32 Technical Details 33 Connection and conditions for use You can connect your Concept Combo 2300 to a direct exchange line DEL a line connected to a local exchange with its own phone number to an extension on an approved compatible PBX Do not connect the Concept Combo 2300 as an extension to a payphone The ringer equivalence numbers RENs of all instruments phones fax machines etc connected to an exchange line must not add up to more than 4 otherwise one or more of them may not ring and or answer calls c
15. ansfer the call to a cordless handset INT press the INTERCOM button The external call will be put on hold 1 2 If the base has only one cordless handset registered it will immediately start calling that handset but if more than one handset is registered enter the number for the handset you want to transfer the call to When the handset answers the intercom call simply hang up at the base to transfer the call Binatone Help Line 0845 345 9677 21 If the handset does not answer within 30 seconds the transfer will be cancelled and the external call reconnected to the base Alternatively once the intercom ringing starts and the display shows for example CALLING HS1 you can hang up the phone to transfer the call automatically The display will change to TRANSFER HS1 The called handset will ring for 1 minute but if it does not answer both the base and handset will ring for another minute If neither answers the ringing will stop and the external call will be released Receiving a transfer call from a cordless handset When you have an intercom call transfer your handset will ring and the display will show HS 1 CALLING To answer the call pick up the handset and you will be connected If you want to end the intercom transfer hang up the phone o Set up a three way conference During an external call it is possible to conference in another handset y 314 During a call press INTERCOM button an
16. ber in your phonebook Scroll UP or DOWN until you see the contact you want to edit Then press the MENU OK button and a flashing bar will appear at the end of the name Use the keypad to enter characters or DELETE button to delete Press the MENU OK button to confirm and the display will move the flashing bar to the end of the number position Use the keypad to enter digits or the DELETE button to delete Binatone Help Line 0845 345 9677 14 Mory ofS Once you have finished press MENU OK button to confirm and the display will show MELODY 1 Scroll UP or DOWN to select a melody Then press the MENU OK button to confirm and the display will go back to the previous menu To store a last number redial in your phonebook ce P 4 or v eB FO Press the REDIAL PAUSE button to review the last number redial list Scroll UP or DOWN to find the number you want to store Press the MENU OK button Then the display will show ADD TO PB Press the MENU OK button to confirm and the display will show a flashing bar at the beginning of the name position Key in the name for this redial number into the phonebook Press the MENU OK button to confirm the name The display will move the flashing bar to the end of the number position If the number needs modifying use the keypad to enter digits or the DELETE button to delete Press the MENU OK button to confirm the number and the d
17. d enter the number of the handset INT you want to connect to by using the keypad The display will show the handset name you have entered and the other handset will ring If the number you have entered is not available you will hear an ERROR tone and the call will be returned to the original handset If you do not enter any number within 30seconds the call will also be returned to the original handset Once the other handset answers the call press STAR button and the display will change from INTERCOM to CONFERENCE and both the base and the cordless handset will be connected to the external call When either the base or the handset hangs up the other will still be connected to the external call Receiving a conference call Dy When you receive intercom ringing from a handset answer the call and the display will show INTERCOM Then wait for the other handset to initiate the three way conference call Either handset can just hang up to end the call and the other handset will still be connected Binatone Help Line 0845 345 9677 22 a Page locate a handest pu Press the INTERCOM button If you have only one cordless handset registered INT to the base the display will show CALLING HS1 and the base will beep If you have more than one handset registered to the base the display will show HS with the registered handset numbers above and the base will output a continuous beep until you press
18. e Handsets can also be de registered using another cordless handset as described in the cordless handset user guide Binatone Help Line 0845 345 9677 24 e SOS call function The SOS call function is very useful for people at home to make an emergency call to ask for help from their relatives police doctor etc How SOS call function works e Press and hold SOS button Cr for more than 2 seconds e The line is automatically seized and dials to each of the pre stored SOS numbers starting with the first and it will wait for 1 minute and then drop the call e The line is automatically seized and dials to each of the pre stored SOS numbers will wait for 1 minute and then drop the call e Then it makes another call to the second SOS number if programmed and sends the lannouncement to ine for another 1 min e Finally it will make another call to the third SOS number if programmed and send the announcement to line for another 1 minute How to terminate SOS call function e When the SOS call function is active you can only terminate this function by lifting up the corded handset on the base It can not be terminated by using any buttons on the cordless handset o Set SOS numbers User is allowed to set up to 3 SOS numbers and 1 SOS voice recording XB am Press the MENU OK MUTE Scroll DOWN until you see SOS SETTINGS 4 o Press the MENU OK MUTE and you will
19. eed this function if your phone is connected machine recording to a PBX or if you use BT Calling Features Important When the instruction simply say press a button this means you should press it briefly then release it When the instruction say press and hold a button this means you should keep it pressed until the display changes or you hear a tone Binatone Help Line 0845 345 9677 1 Eg What s on the display The display of your telephone contains one line with the Time Date and Icons one line of numbers and one line of text Hm Number field shows the telephone numbers t B BEE BEE EEE DIN GI HEN teed Bi BEI H HE Character field shows the Menu ee lt 5i name and status of a call What do the symbols mean Pal Talk This will display when the user picks up the d handset Ring Off e This will display when the ringer is set to E OFF ta Phonebook e This will display when you are in the phonebook menu Voicemail e This will display when you have a new Voice M Mail message This is a caller id service and is not usually available from UK network providers RPT Repeat CID e This will display when the same caller has called more th n once NEW New CID This will display when there is a new CID entry or if one is being viewed Sequence e Indicates the sequence number of the CID record d Hands free speakerphone This will display when the speakerphone is
20. flash times 100ms 250ms and 600ms to meet your telephone line or PABX requirement Press the MENU OK Scroll DOWN until you see SETTINGS Press the MENU OK and then you will see DELETE HS Scroll DOWN until you see FLASH TIME Press the MENU OK and the display will show the current setting of the Flash time e g 100 ms Press the UP or DOWN button to show the flash time you want on the display Press the MENU OK button to confirm the option and you will hear the confirmation beeps The display will return to FLASH TIME Press the PHONE BOOK BACK until you return to idle mode Binatone Help Line 0845 345 9677 26 E o Set Dialling Mode Tone Pulse The default setting of this CC2300 telephone is TONE also called Touch Tone MF or DTMF and normally this will be correct for the UK so will not need to be changed However for some old telephone lines or PABX systems you may need to change the dialling mode from Tone to Pulse Press the MENU OK Scroll DOWN until you see SETTINGS Press the MENU OK and then you will see DELETE HS Scroll DOWN until you see DIAL MODE Press the MENU OK and the display will show the current setting of Dialling Mode e g TONE or PULSE Press the UP or DOWN button to show the dialling mode you want on the display Press the MENU OK button to confirm the option and you will hear the
21. ght W two 1 2V 550mA rechargeable batteries and a battery compartment cover for each handset W up to five charger pods each with a mains power supply for multi handset systems W two user guides one for the corded phone and one for the cordless handset Keep the packaging materials in a safe place in case you later need to transport the unit Keep your sales till receipt which is your guarantee Where to find it Delete DEL Press to delete messages memos stored numbers or Caller Display records P Up Down CDS Intercom INT Press to make an intercom call or to transfer a call Pross to access me aller display records LCD Display and scroll through them Binatone Press to change earpiece speakerphone volume Press to scroll through the lists and menu options Phonebook Back LL ic Press to access phonebook records Press to exit present menu One touch Memory Menu Ok M1 M2 M3 Press to access menu Press as OK key to confirm your operation Press to call numbers stored on One Touch memory o P Press to redial the last number Press while dialing a number to insert a pause amp MUTE Press to mute un mute microphone Press to call or answer a call by using the speakerphone sos Call F Press and hold for 2 seconds to activate the SOS call during a call R Recall For speakerphone and answering You may n
22. he stand to the bottom of the phone in the slots near the rear of the base as shown below cHlexible clips Insert the rigid clips of the stand into the slots on the bottom of the phone nearer the centre of the base Press down firmly until the flexible clips clicks into place To remove the stand 1 pinch the flexible clips 2 pull back the stand and then 3 slide up and forward as shown below Wall Mount To place the CC2300 on a wall connect the stand to the bottom of the phone in the slots near the front of the base as shown below Binatone Help Line 0845 345 9677 7 e Desk Wall mounting continued Insert the rigid clips of the stand into the slots on the bottom of the phone nearer the centre of the base Press down firmly until the flexible clips clicks into place To remove the stand 1 pinch the flexible clips 2 pull back the stand and then 3 slide up and forward as shown below Mark two points on the wall that are 77 mm apart to lay the fixing centers as shown below Rotate 9 9 BE CAREFUL to check that there are no electrical wires hidden in the wall Fix two screws at the marked locations leaving approximately 7mm between the wall and the the screw head Hang the telephone on the screws using the wall mount slots You may need to remove the telephone from the wall and tighten the screws so that the telephone is securely fixed and does
23. if you haven t changed it the T default PIN is 0000 Press the MENU OK button and the display will show xE NEW PIN Use the keypad to enter the new PIN 4 digits from 0 9 Press the MENU OK button to confirm and the display will show REPEAT Use the keypad to enter the new PIN again and press the MENU OK button to confirm You will hear the confirmation beeps and the display will return to MODIFY PIN Daag 4 5 6 T8 9 0 sm Press the PHONE BOOK BACK until you return to idle mode If you enter the wrong PIN at any time you will hear an error tone and the display will return to the previous menu Binatone Help Line 0845 345 9677 28 e Troubleshooting ALWAYS check first that e You have followed all the steps listed onpages 5 amp 6 to install and set up your CC2300 e All connectors are firmly inserted in their sockets e Mains power to the base unit is switched on at the socket e The handset s batteries are correctly and securely installed and are not run down Everyday use cannot make or answer calls e Check that the base unit s mains power adapter is plugged in and power is switched on The base unit needs mains power for normal operation of the phone only the basic handset calling works without mains power e Make sure you are using the telephone line cable supplied with your CC2300 Other telephone line cables might not work e Switch off power a
24. ing in the telephone number to make the call It is not possible to dial numbers from memories when the mains power is off When the mains power is off you can also answer an incoming call with the corded handset When the phone rings pick up the corded handset After lifting the handset you will need to wait for several seconds before you can hear the calling person s voice or before they can hear you Binatone Help Line 0845 345 9677 11 Memory Phonebook management How to enter characters To enter the characters press the button where you see the character e g if you want to 4 2 3 insert the letter A you press 2 2 if you want to insert the letter B you press twice and for C 4 5 6 three times etc If you want to insert AA then you will have to wait for the first A to stop T 8 9 flashing then insert the second A Press 0 z twice for space to delete single characters 3 0 and press and hold Dto delete the whole text Telephone Keypad characters 1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 12th 13th 14th 1 1 _ r 7 4 i d H 2 A B C 2 ala 3D D E F 3 4 G H l 4 i i T 5 J K L 5 6 M N O 6 N O0 6 6 6 6 7 P Q R S 7 8 T UJv 8 9 W X Y Z 9 O space 0 x E
25. isplay will show MELODY 1 Use the UP or DOWN buttons to scroll through the melodies Press the MENU OK button to confirm your selection You will hear a confirmation tone and the display will return to the last number redial list Binatone Help Line 0845 345 9677 15 WEL tare Rer ER i the phonebook Either press the PHONEBOOK CANCEL button once or the MENU OK ESC H button three times and you will see the 1st number and name in the phonebook ZO Scroll UP or DOWN to select the name and number of the person ajorv ww you want to call Note For a short cut to finding the name you can press the digit buttons to go directly to the first entry beginning with the corresponding letters of that key and then scroll from there wy Then pick up the handset or press the SPEAKERPHONE button to make the call Reviewing phonebook memory status This allows you to review how many records in the phonebook are occupied The phonebook allows up to 150 names and numbers Press the MENU OK button to see PHONE BOOK Press the MENU OK button and then press the UP or DOWN buttons until you see MEM STATUS Press the MENU OK Then the display will show the phonebook memory space available e g if you have saved 30 names and numbers in your phonebook it would display 30 150 s t Press the PHONE BOOK BACK until you return to idle mode Direct Memory Call There are three Direct Mem
26. lking 9 hours Battery charge time 24 hours Temperature range Operating 0 C to 40 C Storage 20 C to 60 C Electrical power HANDSET two pcs of AAA size 550mAH NiMH 1 2V rechargeable batteries Base UNIT input 230VAC 50Hz output 7 5VDC 500mA CHARGER POD input 230VAC 50Hz output 6VDC 200mA Port specification The Nyx port connect to the mains power supply is a SELV port with respect to EN41003 CRT The EDF port connected to the telephone line is a TNV port with respect to EN41003 PBX compatibility Timed break recall flash adjustable to 100ms default 250ms or 600ms Pause length 3 seconds Dialling type Tone DTMF dual tone multi frequency or Pulse loop disconnect Network connection This equipment is intended to be used in the UK only Operation on other countries PSTN termination points cannot be guaranteed Binatone Telecom plc operates a policy of continuous improvement and so reserves the right to make changes to the products and functions without notice Binatone Help Line 0845 345 9677 33
27. nt or repair other than through approved agents Please keep your sales till receipt this is your guarantee You should also keep the original packaging material In the unlikely event that you need to return your CC2300 to our Repair Centre while it is under guarantee there will be a 5 handling charge While the unit is under Guarantee 1 Disconnect the base unit from the telephone line and the mains electricity supply 2 Pack up all parts of your CC2300 using the original packaging Remember to include the mains adapter 3 Return the unit to the shop where you bought it making sure you take your sales receipt After the Guarantee has expired If the unit is no longer under Guarantee first follow steps 1 and 2 as for repair under Guarantee Then 3 Call Binatone Helpline on 0845 345 9677 for UK only and ask for a quotation of the repair charge and details of where to send your CC2300 for repair 4 Make sure you include with your CC2300 Your name and address Acheque or postal order for the value of the repair charge 5 Return your CC2300 to the address given by the Service Department This does not affect your statutory rights Binatone Help Line 0845 345 9677 32 p Technical details Standard Cordless Telecommunication Frequency range 1 88 to 1 9 GHz bandwidth 20 MHz Channel bandwidth 1 728 MHz Operating range Up to 300m outdoors up to 50m indoors Operating time Standby 150 hours Ta
28. orrectly The Concept Combo 2300 has a REN of 1 and most other telephones have a REN of 1 unless marked otherwise Binatone Help Line 0845 345 9677 4 e Read First Before Use Choosing a site for the base unit and charger pod The base unit and charger pod s should be placed on a level surface in a position where the mains adapter plug will reach an easily accessible 230 VAC switched mains supply socket never try to lengthen the mains power cable the base unit s telephone line cable will reach your telephone line socket or extension socket it is not close to a sink bath or shower or anywhere else where it might get wet itis not close to other electrical equipment fridges washing machines microwave ovens fluorescent lights televisions etc if the base comes into contact with liquids disconnect it promptly and use a soft cloth to dry it if you believe that the liquid has seeped into the unit do not reconnect the base station Contact the Binatone helpline it is away from hot humid conditions and strong sunlight Mains power connection IMPORTANT The CC2300 base unit must be used with the mains adapter supplied with the unit Using any other adapter will result in non compliance with EN60950 and will invalidate any approval given to this apparatus If you have a Broadband line If you connect your telephone to a line with a broadband connection you will need to insert a micro filter between the telephone and
29. ory buttons M1 and M2 and M3 on the corded base o Store the telephone numbe In idle mode enter the telephone number you want to store eR wea Jeaan bd Press and hold M1 key for more than 2 econds until you hear the confirmation tone to indicate the number has been stored To Speed Dial the telephone numbe m In idle mode briefly press M1 and the unit will automatically dial out the wu telephone number in speakerphone mode Binatone Help Line 0845 345 9677 16 E Caller Display CDS Caller ID CID To subscribe to this feature you need to contact your service provider and there may be a charge for this service Caller Display lets you see the phone numbers of your callers on the display before you answer The base and each handset will store its own CID list independently Both answered and unanswered calls are stored up to a maximum of 20 calls When the caller display list is full any new caller display entry will replace the oldest record The base and each handset will store its own CID list independently Both answered and unanswered calls are stored up to a maximum of 20 calls When the caller display list is full any new caller display entry will replace the oldest record The caller display information includes the caller s number up to 20 digits the date and time of the call the caller s name up to 12 characters if the incoming number matches an entry in the Phonebook Note it will
30. our will be flashing ajor Y Press the UP or DOWN button to set the hour including the AM PM setting 8 Press the MENU OK to confirm The minutes will be flashing Press the UP or DOWN button to setthe minutes Press the MENU OK to confirm Press the PHONEBOOK button to return to the previous menu o B You will hear a beep and the display will show DATE amp TIME edt Press the PHONEBOOK button to return to the previous menu Binatone Help Line 0845 345 9677 9 e Making and answering calls o make a call Pick up the handset and the TALK icon will appear or press SPEAKERPHONE button and the SPEAKERPHONE icon 1 will appear Also the display will show LINE IN USE Use the keypad to enter the number you wish to dial E coun o00 When you have finished the call place the handset back on the base You can also make a call by using the Pre Dialling function Dial the required telephone number first and if you make a mistake you can correct it by using the DEL button to delete digits and then add the right ones Pick up the handset or press the Speakerphone button The number will be dialled out automatically using the handset or speakerphone mode selected To insert a pause in the dialling sequence press the RD P button which will then show a P in the number To make a call from the redial lis The phone remembers the last 10 dialled numbers The list is in order with the most recen
31. see SOS NUMBER Press the MENU OK MUTE and you will see SOS NUMBER 1 2 mn 4 or v Scroll UP or DOWN to select SOS NUMBER 1 to 3 Then press the MENU OK MUTE to select the one you want to program o A o eser m Enter the phone number 42 ens Then press the MENU OK MUTE You will hear a beep and the number is saved D J If you want to save more SOS numbers press the DOWN to select the next location you want to program and repeat above steps Press the PHONE BOOK BACK until you return to idle mode C B ESC Binatone Help Line 0845 345 9677 25 a Advanced use of your phone o Turn on off key tone Press the MENU OK Scroll DOWN until you see SETTINGS Press the MENU OK and then you will see DELETE HS Then scroll DOWN until you see KEY TONE Press the MENU OK and the display will show ON Press the UP or DOWN button to select ON or OFF on the display Press the MENU OK button to confirm the option and you will hear the confirmation beeps The display will return to KEY TONE Press the PHONE BOOK BACK until you return to idle mode o Set Flash Recall time The Recall also called Flash may be needed if you use BT calling functions or are connected to a PABX The default setting of this CC2300 telephone is 100ms and normally this will be correct for the UK However if necessary you can select from 3
32. t message at the top C Press the REDIAL PAUSE button to view the redial list QM a or w Press the UP or DOWN button until you see the number of the person you want to call St Press the SPEAKERPHONE button or pick up the handset to make the call o make a call from Caller Display CID list Press the UP or DOWN button to show the first entry in the CID list If your list is empty the display will show EMPTY a or w Press the UP or DOWN button until you see the number of the person you want to call S 7 Press the SPEAKERPHONE button or pick up the handset to make the call o answer a Call When the phone rings Sa Pick up the handset or press the SPEAKERPHONE button to answer the call Binatone Help Line 0845 345 9677 10 To Mute or Un mute the microphone During a call press the MENU OK button and the display will show ZO CALL MUTED To un mute press the MENU OK button and the display will show a LINE IN USE To change the earpiece or speakerphone volume during a call Aor During a call press the UP button to increase or DOWN button to decrease the 7 Volume EMERGENCY CALL WITHOUT MAINS POWER The CC2300 corded base unit can make an emergency call with the corded handset when the mains AC power is disconnected e Pick up the corded handset After lifting the handset you will need to wait for several seconds to get dial tone before key
33. t the mains socket wait for a few seconds and then switch back on This may solve the problem cannot make a call e Only one handset or the base unit can be connected to the outside line at once If a cordless handset is already using the line you need to wait until it s finished its call The phone does e Check that the base unit s mains power adapter is plugged not ring in and power is switched on The base unit needs mains power for normal operation of the phone only the basic handset calling works without mains power e Make sure you are using the telephone line cable that was supplied with your CC2300 Other telephone line cables might not work Binatone Help Line 0845 345 9677 29 e e The Caller Display e feature isn t You need to subscribe to the Caller Display feature from your network service provider You should find contact working details on your phone bill e The caller may have withheld their number by dialling 141 Or they may be calling from a network that does not transmit the caller s number e g it may be an international call When I try to e If you re using a CC2300 multi handset system check make a call hear whether other handsets are already on a call Busy tone The volume inthe e earpiece is low when I m on a call Make sure you re holding the earpiece correctly over your ear Adjust the volume using the UP DOWN button Intercom and transfer
34. the Binatone Helpline Declaration of conformity The cordless phone identified as CC2300 complies with the essential protective requirements and objectives of EC R amp TTE Directive 1999 5 EC EC Low Voltage Directive 2006 95 EC EC EMC Directive 89 336 EEC And conforms to the following relevant harmonized standards Radio EN 301406 TBR 6 EMC EN 301489 Safety EN 60950 The conformity to the requirements is validated by rC symbol NOTE In compliance with Directive 2002 96 EC when you purchase a product that comes with the symbol shown on the right you are required to dispose the electrical and electronic equipment by separate oct waste collection and you cannot dispose of the product as normal waste This equipment and all its components subsystems and consumable materials form an integral part of this product and when you decide to dispose them you have to bring them to the local recycling centres for appropriate waste disposal in compliance with the current regulations Details about the location of these centres can be obtained from your local authority Binatone Help Line 0845 345 9677 31 The CC2300 is guaranteed for 12 months from the date of purchase shown on your sales receipt This guarantee does not cover any faults or defects caused by accidents misuse fair wear and tear neglect faults on the telephone line lightning tampering with the equipment or any attempt at adjustme
35. the number for the handset you want to page Then the display will change for example to CALLING HS2 if itis handset 2 that is being paged If you enter a number that is not available the base will return to idle mode If you do not enter any number for 1 minute the handset will return to idle mode Handset registration To register new handsets to the base The handset s supplied with your CC2310 system are already registered the first one as handset number 1 the second as number 2 etc You don t need to re register them unless you have a problem To check whether a handset is registered make sure mains power to the base unit is switched on and the handset is within range The handset s display should show its number and the signal level symbol on the display should show three bars If the display shows UNREGISTERED you need to re register the handset using the following process You need to operate the base and handset together 1 On the handset press the MENU OK button to see PHONEBOOK Avi 2 Press the UP button twice to see REGISTRATION 3 Press the MENU OK button to see BASE 1 If the handset already has a registration to a base there is a on the right side of the display and you should choose another base number if you don t want to lose that one Binatone Help Line 0845 345 9677 23 e Press the DOWN button to select a base number BASE 1 2 3 or 4
Download Pdf Manuals
Related Search