Breeze™ SleepGear™ User's Guide
Contents
1. Breeze SleepGear 9 Cleaning EA 9 Caution Do not immerse components with foam pads attached Do not sterilize Do not use bleach chlorine or aromatic based solutions scented oils or moisturizing antibacterial deodorizing or fragranced soaps to clean the nasal pillows mask headgear padding or air tubing Use of such substances may cause hardening of your Breeze SleepGear thereby reducing the life of the product Q Caution Do not expose the mask or tubing to direct sunlight Exposure to direct sunlight may cause deterioration of the product 5 Wash the nasal airway assembly parts in warm soapy water as necessary to remove dirt body oils cosmetics etc Rinse them thoroughly in clean running water and air dry on a clean absorbent surface Foam pads may be wiped with a mild soap applied to a moist cloth 6 To install the vent hole insert align the indicator dot on the insert with the dot on the shell Press the vent hole insert into the Opening in the shell Make sure the inner lip on the vent hole insert is fully inserted into the shell 7 Ifyou are using the halo straps release the ends and pull the straps through the outrigger and cradle slots The cradle may be separated from the spine adapter for cleaning 8 Extend the cradle item 1 to its maximum adjustment and then pull on the cradle more forcefully to separate it from the spine adapter item 2 10 Breeze SleepGear PURITAN BENNETT2. Puritan Bennett Corporation 4280 Hacienda Drive Pleasanton CA 94588 U S A Telephone Toll Free 1 800 255 6774 Authorized Representative Tyco Healthcare UK LTD 154 Fareham Road Gosport PO13 OAS U K 2007 Nellcor Puritan Bennett Inc All rights reserved Rx ONLY 66 0123 Assembled in Mexico 10017598A 0207 tyco Healthcare
3. comfortably at the base of your head 2 Place your hand on the spine and hold it firmly to the back of your head Adjust the length of the Breeze SleepGear with your free hand by moving the nasal airway assembly toward your face Refer to the following figure ll JM TNN ln MMT Mi en Maar gt 3 Adjust the height and angle of the shell so that the Nasal Pillows or DreamSeal device is comfortable and there are no audible leaks 4 Optional Use the halo straps if needed to add stability and enhance the fit of the Breeze SleepGear 6 Breeze SleepGear Use e Adjust the tension of the halo straps for a comfortable fit Do not overtighten the straps e If using the optional clip accessory adjust by first lifting the clip then slide the clip to one of the three available positions along the hose guide that provides the most comfortable fit Using Halo Straps With Clip Closeup of Clip Adjustment 5 Pressurize the interface with your positive airway pressure device and readjust as required to eliminate leaks Notes e The amount of force on your nose should be just enough to prevent air leaks e You may need to readjust the fit of Breeze SleepGear when you lie down e The use of humidification may improve comfort during use Breeze SleepGear 7 Cleaning Cleaning once per week Caution Hand clean only To avoid damage to the Breeze SleepGear never use a dishwasher or other mechanical
4. device to clean the Breeze SleepGear or any of its components Note To prolong the life of the product it is recommended that the Breeze SleepGear be cleaned thoroughly at least 1 Disconnect the back half of the nasal airway assembly item 1 where the hose guide attaches to the spine adapter item 2 2 Remove the Nasal Pillows or the DreamSeal from the shell To remove the Nasal Pillows pinch the Nasal Pillows between your thumb and forefinger then pull the Nasal Pillows out of the shell holes with a gentle rotating motion To remove the DreamSeal from the shell do the following and refer to the next figure Place your thumb and forefinger on the two raised circles on the DreamSeal 8 Breeze SleepGear Cleaning e Squeeze gently to disengage the two side latches Rotate the DreamSeal away from the shell e Disengage the lip on the bottom of the DreamSeal from the notch on the bottom of the shell Caution To avoid damaging the hoses when connecting or disconnecting them use the methods described in the following instructions Never pull on or twist the ribbed portions of hoses Refer to the figure below 9 3 Disconnect the hose at the swivel adapter e Grasp each hose at its rubber cuff Gently pull hoses apart Ey 4 Remove the vent hole insert from the DreamSeal shell Slide your fingernail under the end of the insert with the raised indicator dot s and pull the insert up and out
5. P machine turn oxygen flow off whenever the CPAP machine is off Cautions 9 Cautions are identified by the CAUTION symbol shown above and alert the user to exercise care necessary for the safe and effective use of the Breeze SleepGear lt gt Caution By US Federal law this device may be sold or used only as ordered by a licensed physician Notes Notes are identified by the NOTE symbol shown above and provide additional helpful information 1 Breeze SleepGear Overview The Puritan Bennett Breeze SleepGear Single Patient Use is offered in two airway assembly configurations Nasal Pillows DreamSeal User information for both configurations is presented in this guide Components The primary components that comprise the Breeze SleepGear are Nasal Pillows or DreamSeal e Shell e Vent Hole Insert DreamSeal only e Vent Hole s e Wing Knob Pivot DreamSeal only e Hose Hose Guide e Clip Nasal Pillows only e Outrigger e Spine Adapter Swivel Adapter e Cradle Halo Straps Refer to the figures on the following page Breeze SleepGear 1 Overview Nasal Pillows 1 Nasal Pillows 2 Vent holes 3 Shell 4 Wing knob 5 Clip 6 Hose 7 Hose guide 8 Outrigger 9 Swivel adapter 10 Spine adapter 11 Cradle 12 Halo straps DreamSeal 1 DreamSeal 2 Shell 3 Vent hole insert 4 Pivot 5 Hose 6 Hose guide 7 Outrigger 8 Swivel adapter 9 Spine 10 Cr
6. PURITAN BENNETT Breeze SleepGear User s Guide Contents a E COMPONEM S using inne Nasal PillowWS siiaraini e d DreamS eal ww Indications for Use Ne Technical Data nennen ende oe O SE A SG OO AUS IM esse This manual is available online at http www puritanbennett com Nellcor Puritan Bennett Inc is an affiliate of Tyco Healthcare Breeze SleepGear and DreamSeal are trademarks of Nellcor Puritan Bennett Inc O 2007 Nellcor Puritan Bennett Corporation All rights reserved Breeze SleepGear Contents Warnings Warnings are identified by the WARNING symbol shown above and alert the user to potential serious outcomes death injury or adverse events to the patient or user A WARNINGS Do not block or modify the vent hole s To ensure sufficient air for respiration do not wear the Breeze SleepGear until it is connected to a properly operating CPAP machine At low CPAP pressures flow through the vent hole s may be inadequate to clear all exhaled gas from the Breeze SleepGear Some rebreathing and inhalation of carbon dioxide may occur If you experience skin irritation soreness or discoloration eye discomfort gastric problems such as distention or bloating nasal irritation or dryness excessive hair loss or any discomfort from using the Breeze SleepGear discontinue use and consult your physician If oxygen is used with the Breeze SleepGear or CPA
7. adle 11 Halo straps gm te G CO 7 gt 8 C OLA 6 lt 7 SS Breeze SleepGear Overview Indications for Use This product is intended for use with devices that deliver continuous positive airway pressure CPAP and bi level positive airway pressure in patients weighing at least 30 kg Refer to the warnings on page ii Technical Data The following table provides the technical data for both the Nasal Pillows and DreamSeal configurations Vent Flow Pressure Range and Materials CPAP Pressure Flow Rate cmH2O L min with DreamSeal with Nasal Pillows Parameter Vent Flow Temp Range 40 F to 158 F 41 F to 104 F Storage and 40 C to 70 C 5 C to 70 C Operating Conditions Relative Humidity Up to 95 Up to 95 noncondensing e Nasal Pillows medical grade silicone Materials e DreamSeal Perimeter Seal medical grade silicone Halo Straps Velstretch Breeze SleepGear 3 Assembly Assembly Before using the Breeze SleepGear for the first time assemble it as follows 1 Insert the nasal airway assembly item 1 into the SleepGear assembly spine adapter item 2 The hose guide slides back and forth in the spine adapter with a ratcheting sound 2 Nasal Pillows airway configuration While pinching the Nasal Pillows between the thumb and forefinger insert the Nasal Pillows into the shell holes with a gentle rotating motion 3 DreamSeal airway co
8. nfiguration Perform the following steps and refer to the figure on the next page Attach the DreamSeal to the shell by inserting the lip on the bottom of the DreamSeal into the notch on the bottom of the shell e Place your thumb and forefinger on the two raised circles on the DreamSeal Rotate the DreamSeal toward the shell and squeeze gently to engage the two side latches 4 Breeze SleepGear Use 4 Optional Thread the halo straps through the slots in the cradle see figure below item 1 Then thread the halo straps through the outrigger item 2 or through the optional clip accessory item 3 Nasal Pillows only Engage the Velcro fasteners on the straps Nasal Pillows Side View Note You may wish to try fitting the Breeze SleepGear without the halo straps first then add the straps if a better fit is required Refer to the Adjustment section on the following page Use Inspection Inspect the Breeze SleepGear and its components before each use to ensure all parts are firmly connected and no visible leaks exist Fitting 1 Insert the Nasal Pillows into your nostrils or place the DreamSeal over your nose Breeze SleepGear 5 Use EA 9 Caution Avoid excessive bending of the nasal airway assembly when putting on the Breeze SleepGear 2 Place the cradle back pad below the curve at the back of your head Adjustment 1 Adjust the position of the cradle on the spine so that the cradle sits
Download Pdf Manuals
Related Search