Home

Zulu User Guide - Riverland Sport Aviation

1. Warranty Period This 5 year Limited Warranty Limited Warranty is provided solely for the benefit of the initial purchaser of the New Headset Purchaser and it excludes all 3rd parties including distributors dealers retailers subsequent owners and other users of the New Headset This Limited Warranty is not assignable and remains in full force and effect during the Warranty Period but only if the New Headset a has been properly maintained b has not been Warranty Information abused or misused and c has not been repaired altered or modified without LSA s approval This Limited Warranty specifically excludes all taxes shipping costs and problems relating to any 1 repair alteration or modification not approved by LSA 2 abuse or failure to properly maintain the New Headset 3 faulty workmanship by any person except LSA or its approved agent 4 operation of the New Headset except as specified in its operating manual 5 ordinary wear and tear or 6 finish and appearance item For each claim made under this Limited Warranty Claim Purchaser must within 10 days of discovering a New Headset problem indicating a breach of this Limited Warranty deliver to LSA a written notice that explains in detail the New Headset s specific defect that shows proof of Purchaser s purchase of the New Headset before the end of the Warranty Period and that shows proof that this Limited Warranty applies to t
2. ALL TERMS IN THIS LIMITED WARRANTY EACH SUCH MODIFICATION IS DEEMED EFFECTIVE UPON PUBLICATION ON LSA S WEBSITE OR OTHERWISE TO HE EXTENT ALLOWED BY LAW LSA DISCLAIMS AND PROVIDES THIS LIM EXP OF MERCHANTABIL LSA INDI CLA LSA S TOTAL LIABILI NEG RELATING TO THIS LI THE THE TED WARRAN IRECT SPECIAL LOST MED UNDER ANY STATUTE O LIMITATION OF CONSEQUEN Y FOR ALL CON LIGENCE STATUTORY OR OTHER CLAIMS ARISING FROM OR IMITED WARRANTY OR ANY HEADSET OR PART REOF IS LIMITED TO 1 000 SOME STATES DO NOT ALLOW TY IN LIEU OF ALL OTHER RESS OR IMPLIED WARRANTIES INCLUDING ANY WARRANTY ITY OR FITNESS FOR A PARTICULAR PURPOSE S NOT LIABLE FOR CONSEQUENTIAL INCIDENTAL PUNITIVE PROFITS OR SIMILAR DAMAGES R LEGAL OR EQUITABLE THEORY RACT TORT INCLUDING IAL DAMAGES SO THE ABOVE LIMITATIONS MIGHT NOT APPLY TO PURCHASER THIS LIMITED WARRANTY GIVES PURCHASER SPEC PURCHASER MIGHT HAVE TOS FOR PURCHASERS IN CAL OTHER TATE FIC LEGAL RIGHTS AND RIGHTS THAT VARY FROM STATE FORNIA PURCHASER HAS THE RIGHT TO HAVE THE NEW HEADSET SERVICED AND REPAIRED DURING THE Warranty In WARRANTY PERIOD THE WARRANTY PERI FOR THE NUMBER OF WHOLE DAYS THAT HAS BEEN OUT OF PURCHASER S HANDS REPAIRS IF A DEFECT EXISTS DURING THE HAS BEEN FIXED IF ANY WARRANTY REPA PURCHASER NOTIFIES AFTER THE REPAIR THE WARRANTY PERI FOR A PERIOD EQUAL AFTER A REASO
3. CZ LIGHTSPEED Zulu User Guide Welcome Congratulations on purchasing a Lightspeed Aviation Zulu headset Your headset is a premium product that will provide many years of comfortable high performance for your flying endeavors If this is your first Lightspeed Aviation headset welcome to the Lightspeed family We look forward to building a lasting community with our customers founded on products and service that are best in class To support your passion for flying we invite you to visit LightspeedAviation com where you will find useful insights about our other products and aviation Thank you for choosing a Lightspeed Aviation headset D Introduction 2 Getting Started Fitting YOUrHeGadSetsssasssssscsastaccssssssisssssessscsnssstenesdsss 4 Battery instalation isanne 5 Battery TYPOS sasiessievsscstiescsssseatasssassstacasicstaisniatansensncoed 6 Battery Dife pns 6 Cntr l h sscssiscasiecessscatecsessccsscsssaasbccesesesasostennccneasstuaninsted 6 Using Your Zulu Headset Turning ON ANA OFF asien 8 Matching Stereo Mono Setting to an Audio Panel 8 Front Row Center Auto MusicMute eg Contents Wired Auxiliary Devices u 9 Setting DIP Switches 10 Bluetooth Devices Connecting Cell Phones for the First Time 13 Bluetooth Features isisisi 14 Bluetooth Mode ON and OFF nen 14 FAS essen as Poren 16 Peak Performance Tips 18 Specihie ti ns iassissdensssesudineniostenerismermsense
4. IL SPEC microphone plug Zulu P Audio Panel Straight LEMO Zulu C Two AA batteries Coiled U 174 Zulu CP Audio Panel Coiled LEMO Zulu CD Two AA batteries Coiled Dual general aviation connectors with 250 inch commercial stereo headphone plug and 206 inch MIL SPEC microphone plug 19 20 Specifications General Battery power supply 3V two AA batteries Weight 13 9 oz Headphone Transducer 40mm moving coil Frequency response 20 Hz 20 kHz Nominal impedance 1 kHz Off Mono 180 ohms On Mono 270 ohms Off Stereo 300 ohms On Stereo 550 ohms Microphone Transducer principle Noise canceling electret Frequency response 200 Hz 6000 Hz Maximum SPL 114 dB Terminating impedance 220 2200 ohms Operating voltage 8V 16V DC ANR Maximum SPL Greater than 125 dB at 100 Hz We encourage you to register your headset at our website LightspeedAviation com That way if your headset ever needs servicing registration helps assure quick and efficient processing 5 Year Limited Warranty for New Aviation Headsets Sold by Lightspeed Aviation Inc Lightspeed Aviation Inc LSA warrants that the new aviation headset sold by LSA New Headset is free from all material defects in workmanship and materials For the New Headset all warranties provided by LSA and all implied warranties imposed by law are limited to a 5 year period beginning on the purchase date shown on the New Headset s sales receipt
5. NABLE Ol FOR REPLACEMENT OR REFUND SUBJECT EXTENSION OF THE WARRANTY PERIOD D APPLICABLE LAW THIS LIMITED WARRANTY WILL NOT EXPIRE UN formation OD WILL BE EXTENDED HE NEW HEADSET FOR WARRANTY WARRANTY PERIOD IL THE DEFECT R HAS BEEN DELAYED BECAUSE OF CIRCUMSTANCES BEYOND PURCHASER S CONTROL OR IF ANY WARRANTY REPAIR DID NOT REMEDY A DEFECT AND LSA OF SUCH FAILURE WITHIN 10 DAYS D WILL BE EXTENDED TO THE DURATION OF THE DELAY IF NUMBER OF ATTEMPTS THE DEFECT REMAINS UNFIXED PURCHASER MAY RETURN THE NEW HEADSET TO A REASONABLE DEDUCTION FOR PURCHASER S USE OF THE NEW HEADSET ANY OES NOT AFFECT ANY PROTECTION OR REMEDY AVAILABLE TO PURCHASER UNDER 23 24 Contact Lightspeed Aviation Visit our website Call us Fax Email Mail to Product registration LightspeedAviation com 800 332 2421 503 968 7664 sales lightspeedaviation com or service lightspeedaviation com Lightspeed Aviation 6135 Jean Road Lake Oswego OR 97035 USA Please register at LightspeedAviation com to optimize your customer experience 5 A A 5 S ISO 9001 Cert 0046503 Lightspeed Aviation Inc s Management System is Registered to ISO 9001 2008 amp Bluetooth D Copyright Lightspeed Aviation Inc 2010 All rights reserved Lightspeed Aviation is a trademark and Zulu is a registered trademark of Lightspeed Aviation Inc Bluetooth is a registe
6. Open the controller battery DIP switch door by either pressing down on the circle icon or by pulling open the door along the notched edges Insert two AA batteries with the correct polarity positioning B Getting Started The LED flashes GREEN when charged batteries are in use and the power is on When batteries begin to run low the power LED flashes RED If the LED flashes RED during flight the headset will continue to operate Install new batteries as soon as possible at any indication of low batteries Battery DIP switch door Getting Started Battery Types Use two AA alkaline or lithium batteries Lithium batteries may provide improved battery life in colder temperatures We do not recommend using re chargeable batteries or mixing battery types and brands Battery Life A set of batteries can provide up to 40 hours of power However heavy Bluetooth usage can significantly reduce battery life Under quiet conditions Zulu will auto shut off approximately two minutes after the headset is removed from your head Controller A Power indicator LED Flashes GREEN when power is supplied to Zulu and batteries are strong Flashes RED when batteries are low Power button Powers on headset turning on Active Noise Reduction ANR Press button once to turn Zulu on press and hold to turn Zulu off To toggle the LED brightness from bright to dim quickly press the power button twice Volume
7. about three seconds until a high tone is emitted and the Bluetooth indicator LED flashes three RED pulses Note The Bluetooth feature must be turned ON for Bluetooth connected devices to correctly function Bluetooth Devices 15 16 FAQ s Why do I hear radio communications in only one ear Zulu s Stereo Mono DIP switch is probably set to Stereo while your audio panel is transmitting a mono signal To fix this change Zulu s Stereo Mono DIP switch to Mono This setting does not affect music or audio from auxiliary devices you can hear stereo sound on auxiliary devices even when the Stereo Mono DIP switch is set to Mono When pairing Zulu with my Bluetooth phone why does my phone indicate it cannot connect The headset may not be in pairing mode To enter pairing mode you must start with Bluetooth mode turned fully OFF see Connecting Bluetooth Cell Phones on page 13 Why doesn t my Bluetooth phone accept Zulu s 0000 passcode Your headset may not be in pairing mode Some phones prompt for a pass code without checking for pairing mode When the phone cannot pair with the headset it rejects the passcode To enter pairing mode you must start with Bluetooth mode turned fully OFF see Connecting Bluetooth Cell Phones on page 13 How can I reduce static noise during cell phone calls To reduce RF interference during phone calls keep cell phones at least 12 inches from the Zulu controller and he
8. adset when making calls When flying what causes a warbling noise in the ear cup If your ear is not entirely inside the cup with a tight seal air can seep in and cause the ANR to compensate for uneven internal cup pressure FAQ s 17 18 Peak Performance Tips Start with an excellent fit see Fitting your headset on page 4 Set Zulu s Stereo Mono DIP switch to match the signal from your audio panel see Matching Stereo Mono Setting to an Audio Panel on page 8 Keep cell phones at least 12 inches from the Zulu controller and headset when making call to reduce static noise during phone calls To conserve battery life turn OFF Bluetooth mode when not in use You can use auxiliary devices such as a music player by connecting to Zulu s auxiliary input jack and a cell phone by connecting via Bluetooth or through the standard 2 5mm cell phone cable provided Lightspeed recommends replacement of the soft goods on your headset ear seals head pads and mic muffs every 18 months to ensure peak ANR performance and comfort These are wear items that are not covered by the Lightspeed warranty and are available for purchase on our website at LightspeedAviation com content cfm Store Zulu Configurations Specifications Model Power Source Cord Connector Zulu Two AA batteries Straight Dual general aviation connectors with 250 inch commercial stereo headphone plug and 206 inch M
9. control Controls audio panel volume with individual sliders for each ear Does not affect the volume of auxiliary devices Bluetooth indicator LED Flashes BLUE when Bluetooth mode is on and RED when Bluetooth is being turned off In pairing mode flashes alternating RED and BLUE Bluetooth power button Turns on and off the Bluetooth signal and controls Bluetooth connected devices Auxiliary input jack Provides a wired input for audio and cell phone devices Bluetooth volume buttons Controls the volume of Bluetooth devices Auto MusicMute button When enabled automatically quiets music and audio from auxiliary devices during radio communications Does not affect cell phone calls Getting Started The Zulu controller Using Your Zulu Headset Turning ON and OFF ON Press the power button once to turn on the headset The GREEN power LED flashes when power is supplied Active Noise Reduction ANR is engaged when you turn on the headset OFF Press and hold the power button until the GREEN power LED turns off Zulu will auto shut off approximately two minutes after removing the headset and under quiet conditions The power LED flashes RED when batteries are low see Battery Installation on page 5 Matching Stereo Mono Setting to an Audio Panel The Stereo Mono DIP switch setting should match the signal from your audio panel For a stereo panel best performance is gained by setting the hea
10. d LSA may in its sole discretion i establish separate additional non warranty repair and replacement programs for any new or used headset Non Warranty Service Programs ii the Non Warranty Service Programs may cover any time period before or after any Warranty Period has expired and iii charge any amount and impose any term with respect to any Non Warranty Service Program For Non Warranty Service Programs LSA warrants that all new used reconditioned or refurbished parts and headsets used to repair or replace any headset will be free from all material defects in workmanship and materials but only for a limited period of 90 days thereafter Purchaser acknowledges that used or reconditioned parts may be used to repair any new or used headset and that a refurbished used headset may be provided as a replacement for any new or used headset LSA may hire a 3rd party to repair or replace any new or used headset Including means including but not imited to THE TERMS IN THIS DOCUMENT ARE THE ONLY TERMS THAT GOVERN LSA S WARRANTY OBLIGATIONS FOR ANY NEW OR USED HEADSET OR PART THEREOF NO ORAL OR OTHER WRITTEN TERM APPLIES THIS DOCUMENT PROVIDES THE EXCLUSIVE REMEDY FOR ALL CLAIMS AGAINST LSA WITH RESPECT TO ANY NEW OR USED HEADSET OR PART THEREOF NOTWITHSTANDING ANY PROVISION TO THE CONTRARY IN THIS LIMITED WARRANTY LSA RESERVES THE RIGHT TO MODIFY AT ANY TIME AND FROM TIME TO TIME IN ITS SOLE DISCRETION ANY AND
11. dset for stereo The same is also relevant to a mono panel Incorrect settings result in communications being heard in only one ear The Stereo Mono DIP switch does not affect auxiliary devices so you can enjoy auxiliary audio in stereo regardless of how the Stereo Mono DIP switch is set Front Row Center Front Row Center is a built in feature that gives you a theater like experience enhancing stereo sound reproduction so that audio seems to come from all around you not just from your right and left Auto MusicMute Auto MusicMute is turned on or off by the bottom most controller button With Auto MusicMute on and when radio communications are detected the volume of auxiliary devices will be reduced by 80 percent To enable Auto MusicMute turn on the feature plug into your intercom and talk into the headset microphone while playing music over a wired device see Wired Auxiliary Devices on page 9 If enabled your auxiliary music will decrease when you start to talk Note Auto MusicMute does not affect cell phone calls Using Your Zulu Headset Wired Auxiliary Devices Zulu s wired auxiliary input allows you to connect to cell phones and to most audio devices To connect a music player to Zulu s auxiliary input jack use the cord provided To adjust the volume on a device connected to Zulu s auxiliary input jack use the controls on the device itself Using Your Zulu Headset Setting DIP Switches DIP switch
12. es are factory set to match most aircraft audio panels To change a DIP switch setting open the controller battery DIP switch door Use a small pointed object like a wood toothpick to slide the DIP switch to ON or OFF depending on your preference Changes to other DIP switches should only be adjusted as directed by Lightspeed Aviation technicians 10 Zulu DIP Switch and Their Recommended Use Using Your Zulu Headset DIP switch OFF position ON position Recommendations Stereo Mono Stereo Mono Factory setting Affects audio from the panel only and should be set to Mono in most cases Set to Stereo only if you are using a stereo panel If your audio panel produces a mono signal but the switch is set to Stereo you will hear audio communications in only one ear Leave off Leave set to OFF Test mode for factory use only Continued on next page 11 12 Using Your Zulu Headset Zulu DIP Switch and Their Recommended Use Cont DIP switch OFF position ON position Recommendations Cell mic Cell mic bias Cell mic bias Lets you make phone calls with the headset bias two off Factory on Factory when it is not plugged into a cockpit audio switches that setting for setting for panel Available for battery powered headsets must both be helicopter and battery only Note to helicopte
13. he New Headset LSA or its agent may investigate any Claim For each Claim LSA may in its sole discretion choose any of the following exclusive remedies I repair or replace the New Headset or any part thereof without charge to Purchaser but first Purchaser must return the New Headset to LSA s authorized repair facility pre paying all shipping charges and Purchaser must accept 21 22 Warranty Information the same as repaired or replaced at the facility s location i e FOB the facility within 10 days of the date of LSA s completion notice sent to Purchaser or else LSA will deem the New Headset abandoned in which case LSA may keep sell or otherwise discard it or II refund the New Headset s purchase price to Purchaser Without paying any amount to Purchaser LSA may keep sell or otherwise discard all replaced New Headsets and parts thereof and all New Headsets where LSA has refunded the purchase price to Purchaser In repairing or replacing any New Headset LSA may in its sole discretion use new used or reconditioned parts or provide a refurbished used headset as a replacement In connection therewith LSA warrants that all new used or reconditioned parts or refurbished used headsets will be free from all material defects in workmanship and materials during the Warranty Period and for a period of up to 90 days thereafter but only to the extent that such event occurs during the final 90 days of the Warranty Perio
14. r pilots The ON setting in the same panel powered powered for these switches is incompatible with some position headsets airplane headset helicopter audio panels If you plan to use this feature and keep the switches set to ON test the headset in the cockpit before takeoff Noise gating Leave set to ON Leave the switch in the ON position which disables this feature If interested in using this feature call Lightspeed for information Leave off Leave set to OFF Test mode for factory use only Zulu s Bluetooth interface allows cell phone and stereo music streaming capability A2DP Connecting Bluetooth Cell Phones for the First Time Before using a Bluetooth cell phone for the first time with Zulu it must be paired or electronically connected To pair a Bluetooth cell phone with Zulu 1 Turn on the headset and verify the GREEN LED is flashing Make sure Zulu s Bluetooth mode is turned OFF BLUE or RED flashes from the Bluetooth LED should not be present see Bluetooth Mode ON and OFF page 14 2 Press and hold the Zulu Bluetooth button Bluetooth Devices for about five to ten seconds or until the Bluetooth LED continually flashes RED and BLUE This indicates the Zulu pairing mode setting and lasts about two minutes If this step takes longer and the Bluetooth LED is no longer alternating RED and BLUE start over from step one With Zulu in pairing mode follow the menu prompts on your Blue
15. red trademark of the Bluetooth SIG iPhone is a trademark of Apple Inc Part Number 000000807 Rev B3 G LIGHTSPEED Lightspeed Aviation 6135 Jean Road Lake Oswego Oregon 97035 sales lightspeedaviation com service lightspeedaviation com 800 332 2421 toll free 503 968 3113 tel 503 968 7664 fax LightspeedAviation com Change Your Mind
16. rene 19 Warranty Information ueeeee 21 Contact Lightspeed Aviation 24 Introduction Your Zulu headset package includes clockwise from top left on the following page Carrying case User and Quick Start Guide with warranty information Zulu ANR headset with Zulu controller Two AA batteries not included with panel powered headsets Cord clip Cell phone cable with standard 2 5mm connector Audio device iPhone cable with standard 3 5mm connector Introduction LIGHTSPEED Zulu User Guide fore Getting Started Fitting Your Headset Fitting your headset properly is the key to comfortable use and superior Active Noise Reduction ANR capabilities To gain peak performance from the ANR feature it s necessary to have a solid seal around your entire ear combined with a symmetrical fit on your head The following tips will assist in achieving the proper fit A Fit your ears entirely within the ear cups providing a solid seal B Rest the headband lightly on top of your head with the right and left sliders extended to equal lengths C Position the microphone 1 8 inch from your mouth Speak into the microphone side labeled talk which is marked at the microphone base Battery Installation The standard Zulu Zulu CD and Zulu C battery powered headsets require two AA batteries included Use alkaline batteries for best performance A
17. tooth phone directing it to look for Bluetooth devices Select Lightspeed V numbers may vary on your Bluetooth phone from the list of found devices If asked to enter a password or PIN enter 0000 13 14 Bluetooth Devices Your cell phone should now be paired and ready for continued use with Zulu When you turn on the Zulu Bluetooth mode it will connect to the most recently paired device Most Bluetooth cell phones connect to Zulu automatically If that doesn t happen it may be necessary to use the cell phone menu of found devices to signify Lightspeed V numbers may vary Bluetooth Features Depending on the Bluetooth profile of the phone you can use Zulu s Bluetooth buttons to perform several functions Some typical functions are Press the Bluetooth button once for voice dialing if supported by your phone Press the Bluetooth button once to answer the phone when it rings Press the Bluetooth button once to disconnect from a call Press and hold the Bluetooth button for two seconds to redial the last number called Use the Bluetooth volume buttons Zulu s and buttons to adjust the volume Bluetooth Mode ON and OFF ON With Zulu turned ON press and hold the Bluetooth button see page 7 until you hear a high tone and the Bluetooth indicator LED flashes three BLUE pulses For first time pairing see instructions on page 13 OFF Press and hold Zulu s Bluetooth button for

Zulu User Guide - Riverland Sport Aviation

Contents

Download Pdf Manuals

Related Search

Related Contents