Visio-D2521-01-02 CN4986 SEM1600VI User Guide.vsd
Contents
1. 0 000 To 60 000 High N MECHANICAL INSTALLATION MOUNTING 70 C Screw driver 3 mm E 30 C gt IP65 VA a EN50022 DIN RAIL 17 5 mm 56 4 mm RSA Style DIN 43880 1 module width Are To fit or release module Material Polyamide 6 6 self extinguishing Insert screw driver into slot and lever latch away from body Terminals Screw terminal Cable 2 5 mm Max Colour Grey A ELECTRICAL INSTALLATION 1 0 TURN OFF SUPPLY BEFORE WORKING ON ANY ELECTRICAL CONNECTION 2 0 SUPPLY IS OVER VOLTAGE PROTECTED AND FUSED WITH INTERNAL RESSETTBLE FUSE Screened Cable OUTPUT SUPPLY OTe rh Voltage CONNECTION For cable length lt 3 Metres no screen or twist pair required Use recommended types for cable length 3 to 30 metres 4 to 20 mA Screw Driver A Transmitter 3 mm 0 4 to 20 mA Loop D2521 01 02 CN4986 SEM1600VI User Guide2. SEM1600VI SMART POWERED PROCESS SIGNAL ISOLATOR CONDITIONER A IMPORTANT CE amp SAFETY REQUIREMENTS Important Potentially Hazardous situations Persons responsible for the installation and operation of this equipment must be fully aware of all aspects of this guide Failure to follow the instructions can cause severe injuries and damage This product is suitable for environment Installation category II pollution degree The product is classed as PERMANENTLY CONNECTED EQUIPMENT and must be DIN rail mounted inside a suitable enclosure providing environmental protection to IP65 or greater Dc supply must be derived from a local supply and not a distribution system To maintain CE EMC requirements input and supply wires must be less than 30 metres The product contains no serviceable parts or internal adjustments No attempt must be made to repair this product Faulty units must be returned to supplier for repair This product must be installed by a qualified person All electrical wiring must be carried out in accordance with the appropriate regulations for the place of installation Before attempting any electrical connection work please ensure all supplies are switched off ABSOLUTE MAXIMUM CONDITIONS To exceed may cause damage to the unit 50 V dc Protected for over voltage and reverse connection Supply Voltage Current with over voltage Input Voltage Input Current Ambient 200 mA 75 VDC 50 V rms between any term
3. inals 75 mA between terminals Temperature 30 to 75 C Humidity 10 to 95 RH Non condensing PLEASE REFER TO THE PRODUCT LABEL FOR MANUFACTURERS CONTACT DETAILS without notice RECEIVE AND UNPACKING ce X iO Every effort has been taken to ensure the accuracy of this document however we do not accept responsibility for damage injury loss or expense resulting from errors and omissions and we reserve the right of amendment Please inspect the packaging and instrument thoroughly for any signs of transit damage If the instrument has been damaged please notify your supplier immediately OPERATION please refer to data sheet for full technical specification 1 P SIGNAL User settings Volts Signal Range Between 50 to 50 V mA Signal Range Between 50 to 50 mA A CONFIGURATION This product is configured using the USB port of a PC running USB_Speed_Link software available from your suppliers web site During configuration the product is powered direct from the usb port removing the need for additional power If the user wishes to monitor live process data during configuration then powered must be applied Note the input and USB port of the device share the same ground therefore care must be taken to ensure isolation between PC and input circuit This is best achieved by using a portable laptop or notebook PC USB_Speed_Link software is provided with detailed help menu to guide the user through the simp
4. le configuration procedure Unless specified at the time of order this product is DAMPING User settings Independent Rise Fall Settings 0 to 3600 Seconds Range LED Green OK Red ERROR supplied with the default configuration listed below D2521 01 02 CN4986 SEM1600VI User Guide CONTROLLER Additional Data Tag number Process Units Process Data MATHS FUNCTION User Settings Linear 1 2 1 3 3 2 5 3 2 3 Factory default Input range Process Range Units Process Output Output range Damping rise amp fall Maths Tag LINEARISATION O P PROCESS User Setting User settings Scale Range Or Active Scale Select 2 to22 Signal to process segment Process DOWNLOAD UPLOAD INPUT mA Cy Current 4 000 to 20 000 Damping Rise 200 44 Damping Fall 244 Maths Linear 4 to 20 mA 0 to 100 V UserLin PV Segment 0 to 100 proceed 4 to 20 mA 0 Units Linear 4 O P SIGNAL User settings Type Range Between mA 0 to 20 Volts 0 to10 Volts 10 to 10 V POWER SUPPLY Input 10 to 48 Vdc or 10 to 32 Vac Process Input Current Volt FILE SAYE FILELOAD MEMORY RECALL MEMORY Active Range Low OUTPUT SIGNAL CImA CV amp EV 5 000 to 5 000 TAG NUMBER VESSEL 1 15 x HELP SCANDATA READ DATA
Download Pdf Manuals
Related Search