features precautions names and functions of parts troubleshooting
Contents
1. Blue dial EJ Turn clockwise to augment screen blue ATW Compensation is performed automatically MANU At R WB B ATW Sync setting O EJ Vertical sync disturbance may occur when a selector is used to switch between multiple cameras connected to one monitor To prevent vertical sync disturbance set to LL LL external sync Adjust PHASE dial E to eliminate sync disturbance INT internal sync Internal Sync e LL Line Lock Synchronizes the unit with power frequency LL Bt INT PHASE AD caution If the image disturbance doesn t disappear after adjusting the PHASE dial El on the second and subsequent cameras adjust the PHASE dial EI on the first camera If the problem persists check that all the devices have been connected with the correct power cable polarity Iris dial lens iris M If the entire image is too dark or too bright adjust the LEVEL dial W L Low Closes the lens iris making the entire image darker H High Opens the lens iris making the entire image brighter2. a TV radio transmitter magnet electric motor transformer audio speakers the magnetic field they generate will distort the image E Protect from humidity and dust To prevent damages to the camera do not install it where there is greasy smoke or steam where the dampness may get too high or where there is a lot of dust TROUBLESHOOTING Before sending the camera out for repair check the items below If the problem persists after checking these items contact your place of purchase or a Sanyo Authorized Service Center E If no image appears els the coaxial cable attached securely e Are the power and voltage normal e Has the iris of the lens inside the camera been adjusted correctly with the iris dial els there adequate illumination E If the image is unclear els the lens in focus els the lens dirty Dirt or fingerprints on the lens can adversely affect the image Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid commercially available els the monitor adjusted correctly SERVICE The camera is a precision instrument Handle it carefully and always follow the safety precautions If the camera requires service never try to repair it yourself or open the casing For servicing maintenance or repairs contact your place of purchase or a Sanyo Authorized Service Center E Protect from high temperatures Do not install close to stoves or other heat gener
3. e When using an RG 59U 3C 2V cable do not use it on piping or air wiring e Select the cable to use according to the distance between the devices to connect e f you use a cable other than the types above the image or sync signal will be attenuated and will not be transmitted correctly 24 V AC connection E Camera installation Camera screws Shorter Bracket screws Longer GND AC24V 12 V DC connection GND AC24V 3 sicicie DC12V 2 Figure 2 Making connections 1 Connect the camera and peripheral equipment with cables 2 Connect the power cable lt When using a 24 V AC adapter gt Connect 3 wire grounded cable use 18AWG to the ground GND terminal as shown in Figure 1 lt When using a 12 V DC adapter gt Connect the cable as shown in Figure 2 FD caution e When connecting the power cable to the camera check that the polarity is correct e To prevent fire hazard any UL listed wire rated VW 1 should be used for the 24 V AC cable input terminal 3 Insert the power adapter plug into the wall outlet The power indicator POWER lights Camera installation Camera attachment bracket As shown in Figure E above you can remove the camera attachment bracket and reattach it to the camera bottom if you want to attach the camera to the top of an object If you remove the camera attachment bracket be sure to use the re
4. Francais Deutsch PENS a SANYO INSTRUCTION MANUAL VCC 8115P COLOR CCD camera About this manual Before installing and using the camera please read this manual carefully Be sure to keep it handy for later reference Depending on the conditions of use installation and environment please be sure to make the appropriate settings and adjustments If you need help with installation and or settings please consult your dealer FEATURES E Backlight compensation Multi spot metering and center weighted metering functions E 1 4 inch CCD solid state image device about 320 000 pixels E Vari focal lens with automatic iris E Horizontal resolution of 350 TV lines S N ratio of 48 dB min E Minimum required illumination of 1 2 Ix F1 4 lens E High sensitivity minimum required illumination of 0 4 Ix High Gain F1 4 lens EPower supply 24 V AC and 12 V DC operation External dimensions 134 5 9 ke lt 1 4 20UNC 4 NAMES AND FUNCTIONS OF PARTS POWER power indicator Lights when the camera power is ON VIDEO OUT video output terminal BNC connector Connects to the VIDEO IN video input terminal on the VCR or monitor GND AC24V DC12V ground terminal 24 V AC or 12 V DC input terminal Camera adjustment setting panel Contains camera adjustment dials and sett
5. asizes object outlines SHRP NORM Normal setting Lit NORM Gain control AGC A For adjusting the sensitivity of the camera Use this setting for shooting in dark environments HI HI Increased sensitivity allows shots to be taken in dark environments 4 NORM Normal setting NORM caution The HI setting causes noise generation and a grainy image Backlight compensationE 4 You can set the metering area i to have the lens iris adjust automatically to make the image easy to see when the object is backlit FN Zoom and focus adjustment lt When there is backlight in the entire screen Multi spot metering gt The screen is divided into 48 areas and each area is metered and backlight compensated BLC CENT MULTI TA E OFF LD caution If the background of the object is extremely dark the center of the object may be too bright In this case set center weighted metering mode as shown below lt When there is backlight only in the background Center weighted metering gt Only the center of the image is metered and backlight compensated BLC CENT MULTI o OFF P CAUTION Do not set switches EJ and EJ both to ON Compensation will not be performed correctly with this setting White balance color compensation E KA EJ MANU Lets you fine tune the white balance manually e R Red dial FA Turn clockwise to augment screen red WB e B
6. ating devices such as spotlights etc or where it could be subject to direct sunlight as that could cause deformation discoloration or other damages Be careful when installing close to the ceiling in a kitchen or boiler room as the temperature may raise to high levels Install where the temperature range will stay between 10 C 14 F and 50 C 122 F no condensation E Cleaning e Dirt can be removed from the cabinet by wiping it with a soft cloth To remove stains wipe with a soft cloth moistened with a soft detergent solution and wrung dry then wipe dry with dry soft cloth e Do not use benzine thinner or other chemical product on the cabinet as that may cause deformation and paint peeling Before using a chemical cloth make sure to read all accompanying instructions Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time as that may cause damage or paint peeling Printed on recycled paper SANYO 1AC6P1P2635 L5AJ2 XE 0103TR SY01 SANYO Electric Co Ltd Printed in Japan SPECIFICATIONS PAL standard 625 scanning lines 25 frames second Interlace PLL 2 1 interlace Image device 1 4 inch solid state CCD Number of pixels 537 H x 597 V Number of pixels in image area 500 H x 582 V Sync system Internal sync line lock manually switched Resolution Horizontal 350 TV lines Vertical 400 TV lines Camera output terminal 1 0 V p p 75 Q
7. composite Image S N ratio 48 dB min Vari focal lens F 1 4 1 8 f 2 8 5 8mm Horizontal 35 65 Vertical 27 51 Angle 43 77 Minimum required illumination 1 2 Ix approx with F1 4 lens Backlight compensation function Set to MULTI or OFF Set to Center or OFF White balance Set to Auto or Manual Attachment screw hole diameter 1 4 20UNC top or bottom surface Operating environment Ambient temperature 10 to 50 C 14 to Scanning system 122 F Humidity 90 RH max Power 24 V AC 50 Hz 12 to 15 V DC Power consumption 2 5 W approx Weight 283 g approx Appearance and specifications are subject to change without prior notice CONNECTIONS INSTALLATION EN Connections Monitor lt 1 A I A I 1 i I I T I I I I I t I I lt a i lt i a Digital video recorder or time lapse VCR 3 EF C b gt gt VIDEO IN D gt VIDEO OUT Figure 1 FN Connections What you will need e Peripheral equipment such as monitor digital video recorder or time lapse VCR e Cables for connecting peripheral equipment and camera coaxial cables connecting plugs e Power adapter 24 V AC or 12 V DC Coaxial cables supported You can use any of the following coaxial cables eRG 59U 3C 2V Length About 250 m max eRG 6U 5C 2V Length About 500 m max eRG 11U 7C 2V Length About 600 m max P CAUTION
8. ing switches Lens cover Protects the lens from damage Camera attachment bracket Used to attach the camera located on underside at time of factory shipment Attachment screw hole 1 4 20UNC Focus ring Used to focus the lens Focus ring knob Used to fix the focus ring in position Zoom ring knob Used to fix the zoom ring in position Zoom ring Used to zoom in out PRECAUTIONS E In case of problem Do not use the camera if smoke or a strange odor comes from the unit or if it seems not to function correctly Disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Center E Do not open or modify Do not open the cabinet as it may be dangerous and cause damage to the unit For internal settings and repairs consult your dealer or a Sanyo Authorized Service Center E Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the camera If used with a foreign object inside it could cause a fire short circuits or damages If water or a liquid gets inside the camera disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Center Be careful to protect the camera from rain sea water etc E Be careful when handling the unit To prevent damages do not drop the camera or subject it to strong shock or vibration E Install away from electric or magnetic fields If installed close to
9. moved screws when reattaching it other screws may not fit caution When using the camera attachment stand sold separately select a location that will be able to withstand the weight of the camera and stand for many years and fix them securely in place ADJUSTMENT SETTINGS Zoom in TELE Zoom out WIDE e The settings shown for switches Jj to are the settings at time of factory shipment e Use a Phillips head screwdriver to adjust dials FA to W EN Zoom and focus adjustment 1 Remove the lens cover 2 Loosen the zoom ring knob and turn the zoom ring to zoom in or out increase or decrease the size of the object in the frame 3 Loosen the focus ring knob and turn the focus ring to focus the object e When you have finished adjusting the zoom and focus tighten the zoom and focus ring knobs securely and attach the lens cover caution Take care not to touch or scratch the lens surface front lens when making adjustments Camera adjustment settings The camera comes pre adjusted and ready to install at time of factory shipment but you may want to make adjustments or settings to adapt to the operating conditions or installation environment if necessary If you have trouble adjusting the camera contact your place of purchase or a Sanyo Authorized Service Center Aperture outline compensation El If object outlines appear too strongly set to NORM SHRP Emph
Download Pdf Manuals
Related Search