AMACS GSM installation and operating instructions
Contents
1. r 0 k Operation Message format e number TELA0123456789 out phone number TELB987654321 igh text description IPAHabcdefgh fh pees description IPALabcdefgh B Low to High text description ault message Event2 IPBHabcdeigh default message Event2 PBLabedefgh Turn relay 1 A ON RLA1 Turn relay 1 A OFF RLAO Turn relay 1 A ON for a 5 second pulse RLAP Turn relay 2 B ON RLB1 Turn relay 2 B OFF RLBO Turn relay 2 B ON for a 5 second pulse RLBP Request input output and credit status STAT AMACS GSM installation and operation Text message commands 1 to 6 above are typically used before panel commissioning to set up dial out phone numbers and dial out fault status messages Messages 7 to 13 are typically sent in normal operation to energise de energise or pulse relay outputs and request a panel status update Before any set up or control commands can be sent the AMACS panel must a be powered up The Power Watchdog LED illuminates constantly when DC power is applied and b have acceptable Network reception strength as indicated by the Network Signal indication LED on the circuit board Note It may take a short time for the system to find and detec the GSM network once the network LED illuminates the s is ready to operate The lighting or flashing of the LED determines the str network signal ON OFF ON Equal Length Flashes Good Signal Str2. AMACS GSM installation and operation yi6359 revision E 4 May 2007 p4 4
3. 1 LED indicator description General product specifications and overall mounting dimensions can be found on page 4 of this document AMACS GSM installation and operation Electrical connection General Electrical connection is via screw terminals on the lo the main circuit board with cable access by a remomwab in the panel base AMACS circuit board rela outp fuse i input i ead Screwdriver to loosen tighten each terminal mary power supply owered from a 12 volts DC supply 9 5v min to ax range Connect the negative or zero volt Ov supply terminal of the DC IN terminals connect the positive DC supply to the terminal of the DC IN terminal power supply fuse is fitted on the circuit board above the DC supply terminals see specification for fuse rating Note The DC voltage for either the power supply or the digital inputs must not exceed the maximum stated values typically 14 0 v DC otherwise damage may occur 4 to Aux input Secondary power supply The Aux input terminals allow the optional connection of a secondary 12VDC 9 5v min to 14v max power supply usually a rechargeable battery of lower capacity than the DC input primary supply The Aux input is typically used to power AMACS for short periods of time when the primary supply is either out of normal limits e g during engine cranking or unavailable e g following supply failure or eq
4. at below To set a primary A number of 01234 567890 send command TELA01234567890 The Send Receive LED should briefly flash to indicate reception of the command Important Note the phone number segment of the text command must be in one of the following formats 077961234567 UK dialling format 4477961234567 International Dialling Format When entering the international format do not place the in front of the phone number yi6359 revision E 4 May 2007 p2 4 Step 3 Set secondary phone number After an input activation deactivation or status message has been sent to the primary number the AMACS may be optionally set to send the same message to a secondary number The secondary number operates in a similar way to the primary number but is programmed into the AMACS using the following text commanad To set a secondary B number of 09876 543210 send command TELBO 9876543210 The Send Receive LED should briefly flash to indicate reception of the command Step 4 Set inputs 1 amp 2 description amp operation Each AMACS input 1 or 2 may be programmed with one or two text descriptions allowing a relevant message to be sent back to remote mobile phone s in the event of input activation and or de activation The text descriptions are programmed into AMACS by sending text commands in the following formats For AMACS to send a Pump running message when input 1 A goes high
5. ength OFF ON Permanently on OFF Full Signal Strength If the LED is then there is insufficient signal strength for th tion correctly To correct this problem move the to a location that has greater signal is iot possible fit an antenna extension cable signal reception ork signal strength is acceptable even at the short pulse nal indicated by the network signal LED Once acceptable ength has been obtained the AMACS GSM can be med and controlled to the user s requirements WARNING correct set up and operation is dependent on a minimum level of network signal strength Murphy cannot accept responsibility or liability for operating failures caused by poor network signal Set up procedure and commands Step 1 Identify AMACS phone number Read the AMACS GSM device mobile phone number which is located on the rating plate within the unit enclosure This number should be stored in the user s mobile phone with a name that is relevant to the location operation of the AMACS unit e g Pump 1 Diesel Tank Hopper No2 etc Step 2 Set primary phone number When an input activates e g during an alarm or if a status update command is received the AMACS panel can be set to dial out to a primary phone number The number must be that of amobile phone capable of receiving SMS text messages The primary dial out number is set in the AMACS unit by sending an SMS text message in the form
6. from Ov DC to 12v DC send program commana IPAHPump Running For AMACS to send a Pump stopped message when input 1 A goes low from 12v DC to Ov DC send program command IPALPump Stopped To inhibit any dial out or message when input 1 A goes high from Ov DC to 12v DC send the program commanda IPAH To inhibit any dial out or message when input 1 A goes low from 12v DC to Ov DC send the program command IPAL Note If no input 1 program commands are sent to the AMACS unit the default text of Event 1 is used is sent out as a notification message for both input activation and deactivation Text descriptions for Input 2 B activation and or deactivation may be programmed into AMACS using command format above but with prefixes IPBH or IPBL For each program command sent the AMACS Se LED should briefly flash to indicate reception of th message Control Commands user s mobile Si After set up is complete text commandsro phone can be used for two AMAC rol fe e Energising de energisin Ising either relay output e Requesting the AMA Operating the relay o Energisation de energis can be achieved i following forma sing of each AMACS relay text commands in the To energi ay 1 send the text message RLA1 To N relay 2 send the text message gise turn OFF relay 1 send the text message te 0 zero To de energise turn OFF relay 2 send
7. gh and or low a separate text message for each input transition The inputs are designed for use with remote contacts that close to battery positive input high or go open circuit input low Relay outputs AMACS has two relay outputs output 1 has SPDT changeover contacts output 2 has SPNO normally open contacts Both outputs have volt free dry contacts that will switch up to 3 Amps at 240 volts AC or 3 Amps at 24 volts DC The remote user can send mobile phone SMS text commands to energise de energise or pulse each relay output which in turn may be used to control the remote equipment e g a fault reset contact or a motor pump start signal Input output specifications DC power input 12 volts DC 9 5v 14 0v Aux input Ovolts DC Inputs Switched 12 volts DC 1 A and 2 B Ovolts DC NC Normally Closed contact Relay output 1 A NO Normally Open contact C Common NO Normally Open contact Relay output 2 B c Baer Table 2 Power amp Input requirements Set up and Operation General Set up and control of the AMACS panel is emtir text message commands sent from any m hone h AMACS panel has a unique mobile phone nu or more of which may be programmed into the ad e user s mobile phone each with an appropriat otely set up or control an AMACS system ects the name number of the intended system the number a text message command The followingsi list of commands
8. ry phone number als aSsuming the panel remains powered up prompt should be taken to top up the SIM card credit e If during normal use a status request is made and there is no reply it may be that the credit has expired and there is insufficient credit to permit sending a SMS text message to indicate the status The user can top up the credit on the SIM card without going to the unit or using that SIM card Credit can be applied to the SIM card from any landline phone or mobile phone Follow the instructions on the network Top up card available at supermarkets post offices etc Pay As You Talk SIM card replacement The AMACS GSM comes complete with a Pay As You Talk mini SIM card on the Vodafone network suitable for operation within the United Kingdom and Europe If the modem SIM card needs to be replaced the following procedure should be adhered to Important Turn the DC power to the AMACS unit OFF and then eject the SIM cardholder Push button to eject SIM holder SIM Card Slot Tray Locate the replacement SIM in the holder 1 and put the tray back into the modem 2 Turn on the DC power to the unit SIM Card SIM Card Holder yi6359 revision E 4 May 2007 p3 4 Specifications Electrical amp Network Characteristics DC supply voltage 9 5 to 14 V DC DC supply current 80mA quiescent lt 200mA during GSM receive and transmit Fusing Integral fuse on circuit board 1 Amp fast blow 20
9. the text message LBO note 0 zero To pulse turn ON relay 1 for 5 seconds only send message RLAP To pulse turn ON relay 2 for 5 seconds only send message RLBP Note Pulse commands RLAP and RLAB only operate as described above when the relay is already de energised If a command is sent to an already energised relay the relay will de energise 5 seconds after receiving the command without any subsequent pulse or re energisation AMACS GSM installation and operation Requesting AMACS status If the user wishes to know the status of a particular AMACS unit send the AMACS the text commanad STAT Once AMACS has received this command it will dial out to the primary number and secondary number if programmed and leave a text message in the following format IP Inputs A Active N Non active oo ene ee oe E Energised pone reaned 0123456789 9876543210 Event 1 High Secondarv nhone numbers pee a ow Digital Input text descri Event 2 High Event 2 Low Remaining Credit 1 25 Output trackin sedona The value of remaining credit in Pounds S Pay As You Talk SIM card If a contr se card is used dit left in the modem the unit will not retu Other features Low Credit alarm The AMACS GSM ca t w fauch credit remains on the SIM card and will w e us text message if the credit gets too low Nominated Primary and ch credit check the remaining credit is will dial out to the prima
10. uipment theft Typical connection is fuse_ secondary 12V battery supply OVE eeeeecs rimar DC battery ey supply OV The circuit board blocking diode D above ensures that the secondary battery powers AMACS and only AMACS when the primary supply is unavailable but allows the secondary battery to be charged from the primary supply during normal operation WARNING the secondary battery must be compatible with this method of recharging Consult Murphy or your battery supplier if in doubt yi6359 revision E 4 May 2007 p1 4 The current rating of quick blow fuse F1 must be chosen in relation to the maximum charge current of the secondary battery but should not be more than 1 Amp the maximum current rating of the internal blocking diode One AMACS input may be configured to send a text message warning when the primary supply fails e g due to a battery charging fault or equipment theft For example connect input 2 B across the primary supply shown by dashed lines in the connection diagram above then set AMACS to send a suitable text message when input 2 B goes low A typical set up command might be IPBLPRIMARY DC FAIL see Set up and Operation below for general set up information Digital switch inputs AMAGCS has two inputs which are typically used for monitoring equipment status or faults The system can be set to notify the user s mobile phone when either input goes hi
11. x 5 Inputs 2 digital switch inputs 12 volts DC Outputs 2 relay outputs 1 x normally open 1 x Change over rated 3A 240VAC or 3A 24VDC Network Suitability Suitable for all dual band GSM networks O2 Vodafone Orange and T Mobile SIM Card Mini SIM card for GSM network GSM Coverage Dual band coverage suitable for UK Europe Asia and Far East Excludes North and South American continents Mechanical Characteristics Dimensions max H x W x D 300mm 120mm for antenna x 200mm x 150mm details below Temperature range 10 C to 50 C Protection class IP54 with correct glanding at cable entry Mounting Wall mounted via internal fixings Weight 5 5Kg Dimensions A Pe A a N _ TC35T MODEM Z P N C O i a AMACS PCB oD fuse TT elecrical connections loo oo loo oo ooj 000 C a VA N 160 200 al Fixing dimensions External dimensions and internal layout ie FRANK W MURPHY LTD Church Road Laverstock Salisbury SP1 1QZ United Kingdom MURPHY 4 tel 44 0 1722 410055 fax 44 0 1722 410088 email sales fwmurphy co uk web www fwmurphy co uk USA IS09001 2000 FM 28221 UK SOS004 2000 FM 29422 In order to consistently bring you the highest quality full featured products we reserve the right to change our specifications and designs at any time
12. yi6359 revision E 4 May 2007 catalogue section 30 MURPHY gt Please read the following information before installing A visual inspection of this product for damage during shipping is recommended before installation It is your responsibility to ensure that qualified mechanical and electrical technicians install this product If in doubt please contact your local Murphy representative AMACS GSM Communication Panel Installation and Operating Instructions Description General The AMACS GSM Advanced Monitoring And Control Systems panel is an input output control device capable of 2 way communication with a user s mobile phone The system can be used for status monitoring fault notification and control of remote vital equipment Set up and control of the AMACS panel is entirely by mobile phone SMS text commands The AMACS system comprises a weatherproof panel insi which is a GSM data modem and input output circuit board Indications amp Connections RELAY 2 RELAY 1 ne rm mC NM SUPPLY WO C VP 2 VP 1 OP 2 D P 1 OC SUPPLY IC IMPUTS RELAY OUTPUTS INPUT ower Watchdog _ Illuminates when DC is applied to the unit Flashes when the AMACS develops a fault Network Signal Indicates GSM network signal strength see set up and operation for details Send Receive Illuminates when the AMACS is sending or receiving SMS text messages Flashes when there is no mobile phone number in the configuration Table
Download Pdf Manuals
Related Search