Installation and operating Instructions for
Contents
1. Condensation io Condensation Trap F OU inside Diagram 1b Diagram 1c For installations extracting through cool air spaces i e a loft a condensation trap must be formed by bending the ducting see diagram 1b and 1c Remove the small plug from the bottom edge of the front cover and undo the small screw retaining the front cover Unclip the front cover and remove Hold the body of the fan to the wall or ceiling and mark and drill the fixing holes and appropriate cable entry point Connect the flexible ducting to the fan and secure the end with a cable tie Place the other end of the ducting into the hole in the wall and feed it in as the fan is offered up to the wall Use wall plugs and screws to fix the body of the fan to the wall From the outside pull the ducting through the hole and out the other side by about 75mm 3 Connect the ducting to the wall grille securing it with a cable tie Feed the ducting back into the hole as the grille is offered up to the wall Use wall plugs and screws to fix the wall grille to the wall Prior to connecting the extractor fan to the mains supply check that the body of the fan has not become distorted and that the fan blade can rotate freely within its housing Connect the cable to the fan and the electrical supply as shown in diagram 2a or 2b 13 amp Double Ceiling or Pole Switched FCU with 3A fuse fitted W2. a A A Installation and operating Instructions for 100mm 4 inch Slimline Extractor Fan Models GFANC4SL GFANC4SLT GFANC4SLC amp GFANC4SLTC IMPORTANT SAFETY INFORMATION Please read before starting installation This unit should be installed and maintained by a competent person i e a qualified electrician in accordance with these instructions and in accordance with the current edition of the IEE Wiring Regulations BS7671 and appropriate statutory regulations It is essential that the power source is disconnected and isolated prior to installation and maintenance The fan must be connected to a double pole fused switched connection unit FCU having a contact separation of at least 3mm in all poles and fitted with a 3amp fuse This must be sited outside a room containing a fixed bath or shower Some types of fluorescent low energy lighting systems can interfere with the timer operation To ensure reliable operation only connect fans to tungsten filament lighting circuits These fans are double insulated and do not require an earth connection The location of the fan is important both for its safe operation and for the efficient extraction and replacement of air within a room For best results the fan should be mounted as high and as far away as possible from the main source of air replacement in a room i e opposite the internal door way If the fan is sited in a room containing a fuel b
3. all Switch woe Timer Adjustment For models fitted with a timer adjust to the required overrun period by turning the control with a small screwdriver A hole in the PCB cover is provided to guide the screwdriver Turn the control clockwise to increase the time and anti clockwise to decrease it The approximate time variation is 3 to 25 minutes NOTE The timer control is a precision component DO NOT Dia 2b Fan with Timer apply excessive force when making adjustments Terminal 1 Switched Live Supply Refit the front cover and retain by tighten the small screw DO NOT OVER TIGHTEN Replace the small plug to cover the screw Terminal 3 Permanently Live Supply Terminal 2 Neutral Supply m 13 amp Double IMPORTANT NOTICE TIMER VARIANTS Ceiling or Pole Switched FCU l Wall Switch j j F e r z Wit aA fusefitted Please note the following points when installing and operating oS ae OTOL timer controlled fan variants O ON It is quite normal for the front cover of the timer controlled fans to feel slightly warm to the touch This is the result of the correct operation of the electronic circuit and is not a cause for concern Fan 230V 50Hz N L Dia 2a Fan without Timer Terminal 1 Spare Terminal 2 Neutral Supply Terminal 3 Live Supply J CLEANING AND MAINTENANCE IMPORTANT NOTICE Wiring Colour Changes Regular cleaning of the fan is recommended Before cleaning A
4. s from 1st April 2004 new installations in the UK could be isolate the fan completely from the mains supply wired using the new EU Harmonised colours for the supply If required the front cover can be removed and using a soft conductors OF Mla nel iearinicablg dry brush remove excess dust and wipe the plastic parts with New colours Old colours adamp cloth BROWN Live RED Live Do not immerse the fan in water or other liquid BLUE Neutral BLACK Neutral Never use strong solvents to clean the fan p z 9 The old colours will cease to be used from 1st April 2006 For fans with decorative plated front covers use only a clean dry soft cloth and polish the cover gently Flexible cable colours remain unchanged Do not use strong solvents or other cleaning agents as this BROWN LIVE could damage the plated surface BLUE NEUTRAL Specification All Models Supply Voltage 230V 50Hz Power 20W maximum Extract Capacity 93m per hour IP Rating IPX4 Max Ambient Temperature 40 C Double insulated Complies with BSEN 60335 2 80 2003 GET plc Key Point 3 17 High Street Potters Bar Hertfordshire EN6 5AJ England Helpline Telephone 0121 565 7770 www getplic com C E a AR1535 Ed A
5. urning appliance the installer must ensure that the air replacement is adequate for both the fan and the fuel burning appliance These fans are not suitable for installation within a shower cubicle or directly above a fixed bath The IEE wiring regulations require that mains voltage fans in a room containing a bath or shower must be positioned out of the reach of a person using the bath or shower and that the fans are located well away from all sources of water spray This fan is not intended for use by children or other persons without supervision if their physical sensory or mental capabilities prevent them from using it safely Children should be supervised to ensure that they do not play with the fan GENERAL INSTALLATION INSTRUCTIONS Select a suitable location and make a hole in the wall or ceiling approximately 100mm 4 in diameter allowing sufficient clearance for the ducting Ensure that there is no obstruction on the outside wall or above the ceiling Note For wall installations a fall is recommended i e a slight slope running from the fan to the outside wall see diagram 1a Flexible Ducting Fan inside Fall Wall grille outside Diagram 1a Weathering Weathering dh Slate Slate Rigid PVC N Rigid PVC Ducting Ducting co D Flexible Ducting Fan inside ra N Flexible Ducting A
Download Pdf Manuals
Related Search