INSTALLATION MANUAL
Contents
1. EAA Step 3 Push the U Shape glass seal onto the fixed glass panel prior to insertion into the frames Cut of any excess trim if required 10 www insigniarange com Step 4 Take the first piece of fixed glass with the edge with the seal on and offer it up to the frame You can start with either side of the frame first by simply pushing the glass firmly in to the channel provided Once the glass has been firmly inserted in to the frame secure it in place by using PRC20 both top and bottom and secure in place with ST13 Screws Repeat this for the other fixed glass panel Step 5 ST20 screws Last Modified 28 07 2015 Now meet the front of the shower with the back panels and screw together using the 11 www insigniarange com Last Modified 28 07 2015 Door Wheels Fit the adjustable wheels to the top and bottom of the glass doors by removing the screw and fitting the wheel over the glass as shown in the image Ensure the wheels are facing towards the rail then hang the top wheels on to the top inner curved rail To attach the bottom wheels push the button to lower the wheel and push the wheel into the bottom curve rail Once you are happy that the wheel is in the track depress the button and allow the wheel to enter therefore ensuring a secure a tight fit Next adjust the top wheels by turning the screw clockwise in which in turn will pull the wheels towards the track ensuring a secure a tight fit Now grease2. OUR BADGE RATING IN TERMS OF DIFFICULTY OF ASSEMBLY IS BASED ON CLIENT FEEDBACK 1 Badge Very easy 2 Badges Easy 3 Badges Moderate 4 Badges Harder than average 5 Badges Professional skills required This shower is rated 2 Badges 03 www insigniarange com Last Modified 28 07 2015 ASSEMBLY AND SIMPLE PLUMBING THIS PRODUCT BUILD IS RATED SUITABLE FOR DIY PURPOSES PROVIDING THE CUSTOMER IS OF ABOVE AVERAGE SKILLS AND FEELS CONFIDENT IN THEIR ABILITY ONLY YOU THE CUSTOMER WILL KNOW THIS SO BEFORE ANY ATTEMPT IS MADE TO ASSEMBLY READ THROUGH THE FOLLOWING PAG ES IN DETAIL THEN DECIDE IF YOU HAVE ANY DOUBT USE THE SERVICES OF A PROFESSIONAL IN PICKING SUCH ALLOW THEM TO DECIDE IF THEY ARE CAPABLE OF BUILD BY FIRST SHOWING THESE INSTRUCTIONS TO THEM ALWAYS GET THREE QUOTES REMEMBER THE BEST IS NOT ALWAYS THE CHEAPEST REMEMBER PLUMBERS PLUMB 90 OF THIS JOB IS NOT PLUMBING DUE TO THE NATURE OF THIS PRODUCT WE HIGHLY ADVISE THE PURCHASE AND FITTING OF A WATER SOFTENER ELECTRICAL CONNECTION TO HOUSE MAINS WHEN YOUR ITEM IS ASSEMBLED ALWAYS USE THE SERVICES OF A FULLY QUALIFIED ELECTRICAL COMPANY TO COMPLETE CONNECTION FROM SHOWER TO HOUSE SUPPLY LAWS DEMAND IN MANY CASES YOU DO THIS AND YOUR WARRANTY IS VOID REGARDS ELECTRICAL ITEMS IF THIS IS NOT UNDERTAKEN YOURS AND OTHERS SAFETY IS PARAMOUNT NEVER ATTEMPT THIS YOURSELF REMEMBER These showers are designed to be free standing and movable from their location
3. www insigniarange co uk help aspx ohiana INSIGNIA PRODUCTS HELP HAVE PROBLEMS AND NEED ANSWERS NOW PLEASE KEEP IN SAFE PLACE www insigniarange co uk 18 www insigniarange com Last Modified 28 07 2015 All images are registered with Image raker Insignia is a registered trademark of Maclean International Ltd All images are subject to copyright Images may not be used in any way shape or form with out written permission from Maclean International Ltd Images are NOT permitted to be saved printed or uploaded Violation of copyright laws are punishable by law 19
4. combi boiler will supply this but please check if you have a gravity feed system Important Note Do not exceed 3 4 BAR pressure under any circumstances Warranty is void if so as damage will occur If you have a combi supply please use a pressure reducing valve if required to lower the BAR pressure to the shower Please Remember that this product is free standing and is designed to be pulled away from the wall The water supply and waste require flexible pipes If you purchased the fitting kit with this shower you will have the required fittings The water supply pipes need to be at least 1 metre in length and must be that of a flexi braided type Please note if a shower pump is used via gravity system we recommend a separate cold feed bypassing pump direct to generator to avoid damage to the generator Further to this as you would with a washing machine or dishwasher it is highly recommended that accessible water valve taps are installed to turn off the shower when not In use This will avoid any possible flooding due to a burst pipe or connection failure in the future 08 www insigniarange com Last Modified 28 07 2015 TO START Make sure you have a clear space remember when finished and in place you need access to check your build and able to pull the shower out for servicing or should you have the need to replace anything Take the shower tray and remove all the protective wrapping and fit the waste If you purchased the fitting kit it i
5. the chrome riser bar to the glass wall ensuring the water inlet is inserted through the lower large hole and hand tightened from the rear side Now tighten the chrome shower holder ensuring that this will take the hand shower itself without falling please note over tightening will prevent the holder from sliding up and down 14 www insigniarange com Last Modified 28 07 2015 Accessory Installation Please Note Attach the chrome rain shower bar to the 2 holes located to the top of the centre column Ensure the lower fixing water inlet is securely fastened to ensure a stable connection once the water pipe is attached Note the Large Hex nut goes to the bottom fixing and the smaller one to the top Chrome bar Small washer maine Chrome Sleeve Chrome Ball Connector o Cc Large washer T T 0 Monsoon Shower Head Ensure the washer is placed inside the shower head with the flat edge to the bottom The angled side is for the ball joint to sit in to 15 www insigniarange com Last Modified 28 07 2015 Door Seals Magnetic Seal Push the magnetic door seal on the handle side of the glass door ensuring this is tightly fitted Rear Door Seal Place the rear door seal on the opposite side to the magnetic strip ensuring the Monsoon Shower H L Hand Shower mo Jeo Body Jets Shower Valve Connect the hoses at the rear of the valve to the corresponding fittings No
6. the track to ensure a smooth and long lasting operation not supplied 12 www insigniarange com Last Modified 28 07 2015 Securing the shower to the tray With the main body of the shower cubicle built and connected you now need to connect the shower to the base using the ST20 screws provided Please note this is done now and not sooner so you can manoeuvre the frame and back panels around into position so everything fits together as intended 13 www insigniarange com Last Modified 28 07 2015 Accessory Installation Please Note We recommend using a screwdriver to push through the holes on the back panels to attach the fittings Lightly push the screwdriver from the inside of the cabin to mark the hole and then from the back actually pushing it through This way you ensure a smooth finish to the rear of the panel Shelf Fix the chrome floating shelf brackets to your glass back panel by using the provided screws Now attach the chrome tubed bars to your glass shelf as illustrated in the below image Next slide the shelf into your shelf brackets and secure by tightening the grub screw situated on the bottom of the bracket mh Door Handles SC y i 5 gt Unscrew the handles and with the thread attached a ao to one side of the handle pass it through the pre N S Ue LJ drilled holes on the doors Next attach the other side and screw up tightly Do this for both doors Hand Shower Attach
7. ater setting as hot will make cabin misty and condensate thus the inspection becomes very difficult Now on the OUTSIDE of the shower inspect each joint factory seal hose clip and jet by walking from one side and going around to the back and then to the other side finishing at the front If you have a small leak normally caused through insufficient sealer or air bubble on assembly dry the area thoroughly and reseal on the OUTSIDE Please remember where you see the water this may not be exactly where the leak is as it could have run around to a low point Never seal your inner fittings accessories inside unless you feel it necessary and make sure it is thin and neat remember you will see this for the life of the shower Again leave to cure and check If all good now check shower functions i e jets for back massage foot massage if you have one and finally hand shower check your joints to these functions at the rear again Never use the shower until all checks have been made and the installer is 100 happy in the knowledge no leaks are present All good Now push your shower FROM THE BASE NEVER GLASS OR FRAME into its final resting position Now you can shower in the knowledge that you have no leaks a job done well and long product life Happy showering 17 www insigniarange com Last Modified 28 07 2015 Need Help If so then simply download Insignia s free comprehensive help and troubleshooting brochure now Simply visit
8. s possible this may have already been fitted in the tray hole yet please note this is only for transportation reasons therefore you will still need to ensure the correct sealing and alignment is carried out In the side of the waste supplied in the optional fitting kit you will notice a spigot not seen on an ordinary waste In most cases this is blanked yet should you have a steam version you need to gently drill this out as this item is for the steam generator drainage and will be connected in the instructions later Now please level the tray by firstly placing the tray in its final location and then using a spirit level adjust the tray feet accordingly Once you are happy with the levelling of the tray you can pull it out to begin the main construction Step 1 Align the back panel labelled left and the central column Once you are happy with the alignment using nuts and bolts provided screw the back panel to the column Please repeat this process for the right back panel Notice you have a rubber seal go down the edge of the side panel This is designed to be sandwiched between the backwall and the column You MUST ensure the rubber flap is flat all the way down otherwise leaks may well occur 09 www insigniarange com Last Modified 28 07 2015 Step 2 4 The next step is to attach the uprights to the curved rails using the ST35 screws wider rail with Insignia logo at the top b e Pa
9. should you have need to replace anything ALWAYS USE Flexible braided water inlet pipes at least a metre long not central heating plastic type from house supply to the shower and again flexible waste pipe to join to your house waste NEVER fix with rigid pipes never fix the unit to the wall DURING BUILD LIKE ALL SHOWERS CORRECT SEALING IS IMPERATIVE ALWAYS FIT EASY TO GET TO TAP VALVES ON BOTH HOT AND COLD WATER THE SAME AS A DISHWASHER OR WASHING MACHINE THIS PRODUCT SHOULD BE ISOLATED WHEN NOT IN USE 04 TWO PEOPLE Scissors www insigniarange com Requirements ie Last Modified 28 07 2015 Stanley Blade Silicone Gun Spirit Level Tape Measure Philips Screwdriver Electric Drill 05 www insigniarange com Last Modified 28 07 2015 Whilst the next steps show you how to assemble your shower we want to make sure you have a correct build to ensure you get a trouble free shower Therefore our advice is to follow the instructions and perform a dry run to ensure you are confident with the build and you understand fully how the unit is assembled When we use the word DRY RUN this means you do not silicone anything just simply construct the shower align drill and screw everything together Once you are happy with the build take the unit apart and carry out the final fix What s In The Boxes Tray Box 1x Tray 1x Roof 2x Curved Rails Glass Room 2x Door seals 2x Glass doors 2x fixed glass Col
10. te we recommend that you use PTFE thread tape around each of the fittings to ensure a water tight fitting Device output may differ from the image Please refer to your outer chrome faceplate inside your Insignia shower as a reference point IF YOUR DIAL DOES NOT CORRESPOND TO THE APPROPRIATE DEVICE Turn on your water to the shower and note which output the water exits from then turn off the water and swap over the relevant hose Alternatively remove the outer chrome knob by removing the chrome cap and loosening the grub screw please ensure not to unscrew fully as this will drop within the chrome knob this is found on the opposite side to the chrome pillar Once you have succeeded in loosening this you can now slide your faceplate to correspond to the device Cold Water Inlet Hot Water Inlet 16 www insigniarange com Last Modified 28 07 2015 Silicone Seal where shown in red on the inside of the shower TESTING FOR WATER LEAKS LEAVING SHOWER 24 HOURS AFTER BUILD ALLOWING SEALENT TO CURE With all connections tight the waste and hoses checked jets fully sealed your shower still around 18 inches from its designated final resting point and the silicone fully cured hence leaving for 24 hours minimum Switch on the overhead shower NOT the massage jets remember these will fire water out at you and are not suitable for checking leaks as they would normally only operate when a person is in front of them Just use COLD w
11. umn 1x Complete Column Backwalls 1x Left Panel Backwall 1x Right Panel Backwall In addition to above you will have all the required internal accessories to complete the shower 06 www insigniarange com Last Modified 28 07 2015 Insignia Screw Pack SP011 Note In some cases you may have more screws than needed this is done so you have spares Double Door Wheels m N J J 0 VERY IMPORTANT Have you got everything If not please contact the Insignia Support Line on 01908 226545 Remember NEVER book your tradesman until everything has arrived been checked and is present No replacement missing parts can be obtained free of charge during or after the build Any claims can only be within the timescale permitted 48 hours after delivery and always BEFORE build 07 www insigniarange com Last Modified 28 07 2015 Pressure Requirements from your house supply We recommend a bar pressure between 2 and 3 4 BAR If you have a combi boiler system no problem should be experienced If you have a gravity feed older type installation hot water tank type usually less than 1 bar you will almost certainly need a pump We cannot advise on which type of pump is used location or design because all house plumbing layouts vary This is a job for your installer plumber The end delivery however must fall within the scope above Debit Requirements You will need the debit capabilities of at least 10 litres per minute Again an average
12. www insigniarange com Last Modified 28 07 2015 INSTALLATION MANUAL www insigniarange co uk 30 Day Technical Support 01908 226545 NOTE This service is only available to customers from the day of delivery please have your supplier s details and your postcode to hand before calling Replacements Parts inside of your warranty contact www insigniarange co uk customerService aspx Spares Replacements Parts outside of your warranty contact 0844 800 3069 ATTENTION INSTALLERS Available on the E App Store These instructions must be left with the customer WARRANTY REG NO to claim your full 5 year warranty register your shower within 90 days at www insigniarange co uk warrantyreg aspx www insigniarange com Contents Introduction Requirements What s In The Boxes screw Pack Contents Plumbing Requirements Starting The Installation Accessory Installation Sealing and Water Testing Help Book Information 15 17 18 Last Modified 28 07 2015 02 www insigniarange com Last Modified 28 07 2015 ll Thank you for your recent purchase of an Insignia shower Please read this booklet with great care to ensure you get the best out of your build and have a shower that will last for many years to come Like everything in order to obtain a first class product that will serve you well for many years the effort and correctness put into the assembly will reflect in the quality of your finish
Download Pdf Manuals
Related Search