Installation Manual - Cellular Call Box Gate Intercoms
Contents
1. Enter the following code el lelle i LIL The keypad should now be in programming mode ready to accept new data Additional keypad information Note These features are not commonly used EG IN EGRESS INPUT Connect a push button between this terminal and GND When Egress button is pressed output 1 will be activated for the programmed delay Egress button is usually located inside a building and used as a push to exit K or A KEYPAD ACTIVE OUTPUT An NPN transistor open collector output It switches to ground for 10 seconds on each key touching This can be used to turn on lights CCTV camera or buzzer to notify a guard The rating of this output is lc max 100mA sink Vc max 24VDC DU OUT DURESS OUTPUT An NPN transistor open collector output It switches to ground after the Duress Code is entered Use it to trigger an alarm zone or turn on a buzzer to notify a guard Ilc max 100mA sink Vc max 24VDC DOOR SENSE N C connected to GND to be connected to a normally closed door contact It can be used to generate a door open alarm or door forced open alarm O P 1 Inhibit Normally open When closed this disables all codes for relay group 1 except super user and duress codes Interlock Output NPN transistor output open collector max power 24v dc 100mA sink Used to operate a door in conjunction with another keypad or prevent two doors being opened at the same time Tamper N C Normally closed t2. amp T or T Mobile Exit button switch from gate INTLock 8 Ensure the power is OFF O P1 inhib before inserting the SIM card 12 15v de GND 9 Carefully slide the SIM DU out holder in the OPEN direction Orn insert the SIM and slide in the CLOSED direction to lock it in place Do NOT Force or use a screwdriver GNDo 10 After a final check of wiring switch on the power OUT1 OUT2 11 Allow 20 30 seconds for the unit to boot up and detect the network Once successful connection has been made the unit will sound a confirmation tone and the GSM LED will begin flashing If there is a fault or problem the unit will emit a series of bleeps or warning tones If this occurs check 1 That the SIM card has been activated and has credit 2 That the SIM card does not require a PIN code disable this in a phone 3 That the SIM card can make and received a call on a phone 4 If the SIM card was purchased with a phone that it is not locked to that phone Call the network operator to check 5 Switch off power remove and reseat the SIM card and try again Programming Programming is best done by SMS text It can also be done by DTMF from a normal telephone 1 First check reception Send the following SMS to the unit 20 The unit should reply SIGNAL LEVEL Where will be between 1 and 31 A Below 14 can cause problems with relay T Aa operation or no voice from the gate to the 1 12 13 20 21 31 house Take act
3. GSM3G iB amp iBK OTR tans neat Installation Manual Installation 1 Before you install this equipment please read this full manual 2 Ensure that there is good network reception at the location where it will be installed sae anienna 3 Use the supplied keys to Push button Keypad l open the panel The front door Speaker Key lock ry Migophone will hinge downwards to allow access for mounting holes and connection terminals 4 Note The protective film on the front of the intercom should not be removed until fully installed a Hinge ront door Hinge front door Wall mount Gooseneck mount 5 For external antenna versions install the antenna as high as possible on the top of the pillar to ensure line of sight in all directions for best possible Speech Unit x reception 4 5 feet i minimum Entrance Keep antenna high as possible and Piar above electronics audio equipment Side View to eliminate interference Wi ri ng Antenna connector K Finger tighten only Power LED Hf 6 Carefully follow the GSM LED wiring instructions NNNM Searching SIM card Mmm Network found CPU LED SIM 7 Register your SIM card ean card With the network and check Busy it works in a mobile phone first If you are using a Pre pay or Pay amp Go SIM it will need topped up first Your Hee SIM should be GSM j X compatible USA customers Optional i input limit use At
4. MHZ Check the reception is good Poor reception is not sufficient Check the antenna has been mounted as high as possible not near large metal objects or wet green shrubs etc Check the antenna connection Visually inspect that the centre pin inside the antenna is intact and has not been pushed back inside the fitting Check voltage at the intercom is minimum 11 5V and that the cable from power supply to intercom is less than 3 meters Q The unit calls the first number but there is not enough time to answer before it diverts to the next number A Increase the no answer time as per programming instructions Q The unit calls the first number but voicemail comes on before it can ring the second number A Decrease the no answer time as per programming instructions Q The caller ID part does not work A Be sure to program the caller ID part under 72 feature If your number is a private or number withheld then it will not work Even if you have already programmed a number to receive a call from the intercom if you also want that number to have caller ID access it must be programmed under the 72 feature also Ensure the number is entered as you would normally dial it from another phone Do not put the country code in front of the number Enter the country code in which the unit is operating in separate under the 71 feature International callers ringing the intercom may not work Q There is no audio from the gate but the person a
5. able Pin code 4 8 digits Validate Example Add user 31 to have access code 5555 operating relay 2 aa a LIe Blelblb W Group 2 Add code Location 31 Pin code 5555 Validate 5 10 relay1 a oe m 20 relay2 Delete code ID location to be deleted Validate 30 relay3 fE E Delete a code r Delete all codes in a grou e e 9 le 10 relay1 group 20 relay2 group 30 relay3 group Super delete code Validate Programming Relay output times amp modes e 4 e s 9 L9 9 51 relay1 0 start stop toggle mode latching 52 relay2 1 99999 seconds momentary operation 53 relay3 Validate Programming SUPER user code Super user code is an optional feature which allows the same code to operate outputs 1 2 or 3 e e Location 4 8 digit code Validate Using super user code Using standard user code To use standard code simply enter the 4 digit code Note Remember to exit programming mode with before testing user codes Restoring defaults While in programming mode enter the following to delete all codes and settings apart from the Master code this can take up to 2 5 minutes e Le e Le When the master code is forgotten 1 Wire a push button or replicate with wire link across the Egress terminal and GND 2 Switch off power for 1 minute 3 Switch ON power 4 during the first 60 seconds press the EG button once to enable the function 5
6. amper switch This can be used in conjunction with a tamper switch on a box or enclosure to prevent tampering This can be connected to an alarm system User Manual For SAT3G amp SAT3GK Wireless Intercom This GSM intercom system will call up to 3 telephone numbers in sequence when the call button is pressed There are several modes of operation depending on how the unit has been programmed by your installer The following instructions will assume default programming Intercom calling your phone Press to open OR Press to hold open and ANSWER Press 1 to release again DECLINE as My Gate CALLING Only some gate systems allow lt A hold open control depending on f manufacturer C Call button D Answer call pressed Access Control Options Option 2 If your number 33 5678 is not saved in the intercom memory it will answer the call Enter the code on your telephone keypad to activate the door or gate default code 5678 shown Option 1 If your number is saved inside the intercom biai l i ialling memory just dial it and it will MY GATE activate the door or gate 4 without answering your call a The intercom will end the call for you END Using the Android App If you are using Android you can purchase the Android app at the google play store GSM GATE The app allows easy advanced control of the intercom and gates or door by the simple press of the buttons shown The
7. app will need configured with the SIM card phone number of your intercom before it can be used Once the app is installed pressing the MENU button on your phone will display the setting screen below where you can enter the SIM card phone number If your gate system is set for timed operation where it automatically closes after a preset delay you may be able to take advantage of the latching features a tie na A RODD GSM GATE gt gt gt mal imal GsM GATE Press button to trigger gates speed dials your intercom ENTER GATE PHONE NUMBER Hold open gates Wy oo OLD sends latch SMS command ENTER TEXT COMMAND TO UNLATCH GATES AES BRAND DEFAULT COMMAND 35 5678 Release un hold ates sends unlatch SMS commana ENTER TEXT COMMAND TO LATCH GATES AES BRAND DEFAULT COMMAND 34 5678 Press for additional features 1 Check gate open or closed 2 Check reception level 3 Check stored numbers sending SMS Commands All of the features shown on the Android app are also available for non Android users or non smart phone users You can simply send the same SMS commands manually to the intercom as detailed below 33 5678 Momentary trigger output relay default user pass code 5678 34 5678 Latch output relay default user pass code 5678 35 5678 Un latch output relay default user pass code 5678 20 Check reception level of intercom 21 Check stored numbers Unit will reply with list of stored number
8. e sent together in the same SMS Just 12 1234 720987654321 add 72 then the number then each time The pass code only needs to be put at the beginning of each new messge USA customers For some cell networks you must enter the numbers with the long distance 1 before area code then the number E g 1 702 555 1234 Additional Programming Parameters Code Description Default 0177 Change programming password 1234 0272722 Change access control password allows users not in caller ID list 5678 to call intercom and use pass code to activate relay 03727 Change monitoring mode password dial to listen in mode 1212 Delete a button calling number where n number 1 2 or 3 Speaker volume Where level 0 3 Microphone volume Where level 0 3 51 Relay time Where 1 9999 seconds 53 2 Max call time Where 005 999 seconds 3 digit code 552 2 Max monitoring time for listen in mode when calling the intercom ie 00 60 mins 00 no limit 572 2H Unit can call or SMS service number by set duration to prevent ie SIM card deactivation if seldom used 00 60 days 00 no inform 582 Choose between scheduled call to service number or send SMS to 1 z service number 1 for SMS 2 for call 77number Store service number to receive scheduled SMS or call from N A intercom Dial in mode for withheld numbers or non stored numbers 1 65 answer the call amp wait for pass code 2 answer the call amp 1 automatically act
9. he buttons longer when attempting to activate the gates or door Q The keypad confirm bleeps when I enter my code but the gates or door lock does not open A Check wiring The keypad relay should be connected to the lock or gate system as well as the relay inside the GSM part of the intercom A Check for voltage drop If the voltage is a little low the keypad may operate but fail to fire the relay
10. ion to improve reception Poor Medium Good 2 Program the numbers you wish the unit to dial when the call button is pressed up to a maximum of 3 numbers Each SMS must start with the pass code default 1234 in the following format 12 1234 followed immediately by a command E g to program the telephone number 0987654321 enter the following SMS Up to 3 numbers can be sent together in a single SMS as 12 1234 110987654321 lows 12 1234 1 1tel number1 1 2tel number2 1 3tel number3 11 Telephone number 1 12 Telephone number 2 13 Telephone number 3 Pass code Data Function code 3 It is recommended to change the no answer time if there is more than 1 number stored This stops the unit ringing a number after a set time and can be used to prevent voicemail answering the call Send the following SMS 12 1234 52 Where can be 2 digits from 10 99 seconds default is 20 The unit can allow up to 100 telephone numbers to be stored for users to be able to ring the system for automatic entry This uses caller ID like a phone to determine the identity of the caller First the unit must know what country it is operating in 4 Program the country code as follows 4 0 99 Where can be 1 3 digits For uk insert 44 for Ireland 353 for TAN 2348712 2 USA insert 1 Do not use any leading zeros 5 Enter the telephone numbers required to have access control Do not enter country code hee Up to 3 numbers can b
11. ivate 2 way speech 73 2 Delete phone number for caller ID access N Delete all phone numbers for caller ID access N 999 Restore defaults N O1H Check stored numbers Note no pass code needed for this N A command O dial out number Dial in number Remember to begin each new SMS with pass code 12 1234 Note DTMF Programming is done by calling the unit amp entering the pass code first then after a long single confirm tone commands can be entered A fault is indicated by 3 short bleeps A A A Keypad Programming only ABK models LED indicators ON when incorrect codes entered and outputs are locked out GREEN when output 1 activated RED when output 2 activated SU LU UL Fast FLASHING wrong code entered error JLL SLOW FLASHING in normal standby mode Lo COON in programming mode I LL ON when relay 3 activated alaja Note Programming can only begin 60 seconds after power on Enter Programming mode The unit is now in programming mode Amber LED z will remain ON 0000 is default programmers code Note Pressing again will exit programming mode Enter new programmers code Lo Location 4 8 digit code Validate Record or Delete user codes Lo o Lo o a 10 relay 1 codes 2 add code Memory locations 1000 available 5 delete code 000 999 for relay 1 20 relay 2 codes 001 100 for relay 2 100 available 001 100 for relay 3 30 relay 3 codes 100 avail
12. s dial in number O dial out number 22 Check gate door status Unit will reply Relay On Off Detect On Off SIM cards amp Credit Please note that if you are using a Pay amp Go or Pre pay SIM card which requires topped up occasionally most network providers provide a feature called Auto Top Up This allows you to register the SIM card on their web site and create a payment method When the credit runs low the network will automatically top up your SIM card so that you don t have to worry about running out Contact your network provider in your country for more information or register with them online Fault finding amp FAQs Q The unit will not power up No LEDs on A Check power supply voltage at intercom is within 11 5V 12 5V DC Cable length from PSU to intercom should be less than 3 meters Q The unit powers up but there is a bleeping from the door station A This means the unit is not able to detect the network for some reason Check the SIM card is activated and has calling credit Power off the unit remove the SIM and check it in a mobile phone to verify it can make a call Check the SIM does not ask for a PIN code when put in a phone If it does then disable the PIN code request Check the SIM is a standard GSM SIM not 3G or 4G only SIM If you are unsure contact your SIM card provider to verify Frequency of operation should be any one of the international quad band standards 850 900 1800 1900
13. t the gate can hear ok A This can be due to low reception Check reception level by 20 Change SIM card if necessary to another network which may have better coverage Purchase a high gain antenna This may also be caused by either a defective microphone If reception is optimum and the problem persists contact your supplier or dealer Q The audio quality that can be heard on the remote telephone is poor or humming buzzing A A small amount of GSM buzz can be considered normal on GSM intercoms but not so much that causes inability to hear the person speaking This can be caused by the GSM antenna being mounted too close to the speech panel or not mounted high enough Try earthling the speech panel chassis to OV of the power supply This is also a symptom of poor reception Try above steps on checking and improving reception Q The or key does not work when the intercom calls a phone A Check if you can hear the relay clicking at the gate when the or key is pressed during a call If it can be heard then the system is working check wiring between the relay and the lock or gate panel If the relays do not make a clicking sound then check this feature on a different mobile cell phone or landline If it works on a different phone check the settings on the phone in question under DTMF tones Failure of DTMF tones to operate correctly is also a symptom of low reception Check steps above on improving reception Try pressing t
Download Pdf Manuals
Related Search