Manual
Contents
1. features a2 2 ia imal l a GSM GATE Press button to trigger gates TRIGGER ORNE speed dials your intercom Hold open gates HOL RUN HOI sends latch SMS command GATES GATES ENTER GATE PHONE NUMBER ENTER TEXT COMMAND TO UNLATCH GATES AES BRAND DEFAULT COMMAND 35 5678 Release u n hold ates sends unlatch SMS command ENTER TEXT COMMAND TO LATCH GATES AES BRAND DEFAULT COMMAND 34 5678 Press for additional features 1 Check gate open or closed 2 Check reception level 3 Check stored numbers sending SMS Commands All of the features shown on the Android app are also available for non Android users or non smart phone users You can simply send the same SMS commands manually to the intercom as detailed below 33 5678 Momentary trigger output relay default user pass code 5678 34 5678 Latch output relay default user pass code 5678 35 5678 Un latch output relay default user pass code 5678 20 Check reception level of intercom 21 Check stored numbers Unit will reply with list of stored numbers dial in number O dial out number 22 Check gate door status Unit will reply Relay1 On Off Relay2 On Off Detect On Off SIM cards amp Credit Please note that if you are using a Pay amp Go or Pre pay SIM card which requires topped up occasionally most network providers provide a feature called Auto Top Up This allows you to register the SIM card on their web site and creat2. heard on the remote telephone is poor or humming buzzing A A small amount of GSM buzz can be considered normal on GSM intercoms but not so much that causes inability to hear the person speaking This can be caused by the GSM antenna being mounted too close to the speech panel or not mounted high enough Try earthling the speech panel chassis to OV of the power supply This is also a symptom of poor reception Try above steps on checking and improving reception Q The or key does not work when the intercom calls a phone A Check if you can hear the relay clicking at the gate when the or key is pressed during a call If it can be heard then the system is working check wiring between the relay and the lock or gate panel If the relays do not make a clicking sound then check this feature on a different mobile cell phone or landline If it works on a different phone check the settings on the phone in question under DTMF tones Failure of DTMF tones to operate correctly is also a symptom of low reception Check steps above on improving reception Try pressing the buttons longer when attempting to activate the gates or door Q The intercom makes an audio call but not a video call A Check site 3G coverage check SIM card capability check that the person receiving the call has a phone that already can receive video calls
3. the cable from power supply to intercom is less than 3 meters Q The unit calls the first number but there is not enough time to answer before it diverts to the next number A Increase the no answer time as per programming instructions Q The unit calls the first number but voicemail comes on before it can ring the second number A Decrease the no answer time as per programming instructions Q The caller ID part does not work A Be sure to program the caller ID part under 72 feature If your number is a private or number withheld then it will not work Even if you have already programmed a number to receive a call from the intercom if you also want that number to have caller ID access it must be programmed under the 72 feature also Ensure the number is entered as you would normally dial it from another phone Do not put the country code in front of the number Enter the country code in which the unit is operating in separate under the 71 feature International callers ringing the intercom may not work Q There is no audio from the gate but the person at the gate can hear ok A This can be due to low reception Check reception level by 20 Change SIM card if necessary to another network which may have better coverage Purchase a high gain antenna This may also be caused by either a defective microphone If reception is optimum and the problem persists contact your supplier or dealer Q The audio quality that can be
4. the first number is receiving a video call second number receiving audio call third number receiving video call The unit should reply to each programming text sent with Ok or error message 3 It is recommended to change the no answer time if there is more than 1 number stored When the unit is calling the first number and this no answer time expires then the unit will end the call and begin calling the second number This can be used to prevent voicemail or answering machines picking up the call on the first number 12 1234 52 7 Where can be 2 digits from 10 99 seconds default is 20 Note that video calls take around 5 8 seconds to connect The unit can allow up to 100 telephone numbers to be stored for users to be able to ring the system for automatic entry This uses caller ID like a phone to determine the identity of the caller First the unit must know what country it is operating in 4 Program the country code as follows 4 ox 99 Where can be 1 3 digits For uk insert 44 for Ireland 353 for 1212344 712 2 USA insert 1 Do not use any leading zeros 5 Enter the telephone numbers required to have access control Do not enter country code just the complete number as you would dial it 12 1234 7210987654321 Note As shown you can pick which relay you wish to Data activate when dialling in 3 Pass code Function code telephone number numbers can be entered in 72 Add number the sam
5. to turn on lights CCTV camera or buzzer to notify a guard The rating of this output is lc max 100mA sink Vc max 24VDC DU OUT DURESS OUTPUT An NPN transistor open collector output It switches to ground after the Duress Code is entered Use it to trigger an alarm zone or turn on a buzzer to notify a guard Ic max 100mA sink Vc max 24VDC DOOR SENSE N C connected to GND to be connected to a normally closed door contact It can be used to generate a door open alarm or door forced open alarm O P 1 Inhibit Normally open When closed this disables all codes for relay group 1 except super user and duress codes Interlock Output NPN transistor output open collector max power 24v dc 100mA sink Used to operate a door in conjunction with another keypad or prevent two doors being opened at the same time Tamper N C Normally closed tamper switch This can be used in conjunction with a tamper switch on a box or enclosure to prevent tampering This can be connected to an alarm system User Manual Predator 3G Video Intercom This GSM intercom system will call up to 3 telephone numbers in sequence when the call button is pressed There are several modes of operation depending on how the unit has been programmed by your installer The following instructions will assume default programming Output 1 Press to trigger relay Press to hold relay Press 1 to release relay Intercom calling your phone My Gate CALLIN
6. 200m 5 Install the antenna as high as possible on the top of the pillar to ensure line of sight in all directions for best possible reception mn Keep antenna high as possible and above electronics amp audio equipment Install 4 5 to eliminate interference feet from Entrance i ground Pillar Ensure the speech panel is located at T an appropriate height in order to have oe a good view of a visitor when standing in front of it 6 Remove the top two security screws as shown Do NOT remove the bottom screws The front door will hinge downwards to allow access for mounting holes and connection terminals Remove only top screws Night illuminator pee N Camera __ gt O Night illuminator j gt ____ Note The protective film on the front of the intercom should not be removed until fully installed Speaker _ gt Push Button O 7 Use appropriate wall fixings 8 10mm anchors 75mm deep with M5 screw are recommended as a minimum Hinge front door Side View Output 2 directional antennas it will indicate Connecting DC magnetic Wiring 8 Carefully follow the wiring instructions fj CPU LED Busy Standby Antenna connector Finger tighten only B GSMLED lt Busy Network found SIM card i Power LED holder SIM card 9 Register your SIM card with the network and check it works in a mobile phone firs
7. G Output y Press 7 to trigger relay Press 8 to hold relay Press 9 to release relay ANSWER DECLINE C ST D Answer call Only some gate systems allow hold open poses control depending on manufacturer Access Control Options Output 1 Option 2 If your number QQ i Option 1 If your number is Enora edirii Podi Momentary trigger saved inside the intercom Dialling intercom memory it will 34 5678 Hold relay memory just dial it and it will MY GATE answer the call Enter the activate the door or gate 4 code on your telephone Output 2 s NID 35 5678 Release relay without answering your call keypad to activate the The intercom will end the call door or gate default code 36 5678 Momentary trigger for you 5678 shown 37 5678 Hold relay 38 5678 Release relay Using the Android App If you are using Android you can purchase the Android app at the google play store GSM GATE The app allows easy advanced control of the intercom and gates or door by the simple press of the buttons shown The app will need configured with the SIM card phone number of your intercom before it can be used Once the app is installed pressing the MENU button on your phone will display the setting screen below where you can enter the SIM card phone number If your gate system is set for timed operation where it automatically closes after a preset delay you may be able to take advantage of the latching
8. coon Installation Manual Important Notes 1 Before you install this equipment please read this full manual 2 Before fully installing the system on site it is recommended that the system be set up on a workshop bench with SIM card installed and function tested with the customers phone to check everything works ok BEFORE going to site to install it 3 Please NOTE iPhones DO NOT SUPPORT 3G VIDEO CALLING Almost all other leading brands of smart phone do support 3G video calls Please CHECK your phone can make and receive a video call before installing this system 4 Ensure that there is excellent 3G coverage in your area before you install this system If in doubt install an app on your smart phone We recommend an app called Opensignal It is recommended to have a minimum of 5Mbps download speed and 1 5Mbs upload speed This app also shows the direction of the cell tower that the phone is connected to This should help in deciding antenna location and for 3 networks nearby the direction it should be pointed in Alternatively you can use your standard smart phone display to check the area for good signal strength A minimum of 3 out of 5 bars is recommended with 3G symbol showing on your notification bar Installation Now that you have established both good 3G coverage on site and that the intercom makes a video call to the customer s phone you are now ready to install the system wee GD 4
9. e SMS 1 Relay 1 2 Relay 2 12 1234 722tel number1 721tel number2 722tel number3 Note In this example the first number will trigger relay 2 the second number will trigger relay 1 and the third number will trigger relay 2 USA customers For some networks you may need to enter the numbers with the long distance 1 before area code then the number E g 1 702 555 1234 Try it with and without to see method works Additional Programming Parameters Code Description Default 012 2 Change programming password 1234 02 Change access control password allows users not in caller ID list 5678 oi to call intercom and use pass code to activate relay 03727 Change monitoring mode password dial to listen in mode 1212 Sint Delete a button calling number where n number 1 2 or 3 N A Speaker volume Where level 0 4 3 Microphone volume Where level 0 4 3 50 Relay 1 time Where 1 9999 seconds 51 Relay 2 time Where 1 9999 seconds 5327 Max call time Where 005 999 seconds 3 digit code Max monitoring time for listen in mode when calling the intercom 00 60 mins 00 no limit Unit can call or SMS service number by set duration to prevent SIM card deactivation if seldom used 00 60 days 00 no inform 55 57 Choose between scheduled call to service number or send SMS to service number 1 for SMS 2 for call 58 Store service number to receive sched
10. e a payment method When the credit runs low the network will automatically top up your SIM card so that you don t have to worry about running out Contact your network provider in your country for more information or register with them online Fault finding amp FAQs Q The unit will not power up No LEDs on A Check power supply voltage at intercom is within 11 5V 12 5V DC Cable length from PSU to intercom should be less than 3 meters Q The unit powers up but there is a bleeping from the door station A This means the unit is not able to detect the network for some reason Check the SIM card is activated and has calling credit Power off the unit remove the SIM and check it in a mobile phone to verify it can make a call Check the SIM does not ask for a PIN code when put in a phone If it does then disable the PIN code request Check the SIM is a standard GSM SIM not 3G or 4G only SIM If you are unsure contact your SIM card provider to verify Frequency of operation should be any one of the international quad band standards 850 900 1800 1900 MHz Check the reception is good Poor reception is not sufficient Check the antenna has been mounted as high as possible not near large metal objects or wet green shrubs etc Check the antenna connection Visually inspect that the centre pin inside the antenna is intact and has not been pushed back inside the fitting Check voltage at the intercom is minimum 11 5V and that
11. l keypad L_ keypad L_ keypad output Separate output Separate output PSU PSU Programming Programming is carried out by sending SMS texts to the unit 1 First check reception Send the following SMS to the unit 20 The unit should reply SIGNAL LEVEL Where will be between 1 and 31 Below 14 can cause problems like intermittent relay operation no voice from the gate to the house or no video calling The reply message should show WCDMA If it only shows GSM then you do not have 3G coverage 21 31 Good This scale shows the reception grade from poor to good It is preferable to be in the top end of medium or higher 1 12 13 20 Poor Medium 2 Program the numbers you wish the unit to dial when the call button is pressed up to a maximum of 3 numbers Each SMS must start with the pass code default 1234 in the following format 12 1234 followed immediately by a command E g to program the telephone number 0987654321 enter the following SMS 12 1234 1 110987654321 Note For dialling land lines or non video calling phones the unit can be programmed Data to make standard audio calls telephone number to certain numbers Pass code Function code 11 Telephone number 1 12 Telephone number 2 13 Telephone number 3 2 Video call 1 Audio call Up to 3 numbers can be sent together in a single SMS as follows 12 1234 1 1 2tel number1 121tel number2 132tel number3 Note In this example
12. nds momentary operation 53 relay3 Validate Programming SUPER user code Super user code is an optional feature which allows the same code to operate outputs 1 2 or 3 e e Location 4 8 digit code Validate Using super user code Using standard user code To use standard code simply enter the 4 digit code Note Remember to exit programming mode with before testing user codes Restoring defaults While in programming mode enter the following to delete all codes and settings apart from the Master code this can take up to 2 5 minutes e Le e Le When the master code is forgotten 1 Wire a push button or replicate with wire link across the EG IN terminal and GND 2 Switch off power for 1 minute 3 Switch ON power 4 during the first 60 seconds press the EG button once to enable the function 5 Enter the following code Lelle i CC The keypad should now be in programming mode ready to accept new data Additional keypad information Note These features are not commonly used EG IN EGRESS INPUT Connect a push button between this terminal and GND When Egress button is pressed output 1 will be activated for the programmed delay Egress button is usually located inside a building and used as a push to exit K or A KEYPAD ACTIVE OUTPUT An NPN transistor open collector output It switches to ground for 10 seconds on each key touching This can be used
13. t If you are using a Pre pay or Pay amp Go SIM it will need topped up first Your SIM should be 3G compatible Reset button T NT ocND 10 Ensure the power is OFF P opt before inserting the SIM card Optional limit switch irom gate 11 Carefully slide the SIM holder in the OPEN direction insert the SIM and slide in the CLOSED direction to lock it in place Do NOT Force or use a screwdriver Exit button Tamper 12 Check wiring again and switch on power Advanced Bias 13 Allow 20 30 seconds for unctions f the unit to boot up and detect the network The unit should stop bleeping after 10 15 seconds and the GSM led should begin flashing Keypad Connections only keypad models If there is a fault or problem the unit will continue to sound error bleeps every 30 seconds Check 1 That you have good 3G reception in the area 1 That the SIM card has been activated and has credit 2 That the SIM card does not require a PIN code disable this in a phone 3 That the SIM card can make and received a call on a phone 4 If the SIM card was purchased with a phone that it is not locked to that phone Call the network operator to check 5 Switch off power remove and reseat the SIM card and try again Wiring Tips Connecting AC DC strike Connecting automatic gates lock lock GSM Lock GSM Lack a Gate controller output oc output C_J Lo H i i Optional Optional Optiona
14. t codes entered and outputs are locked out GREEN when output 1 activated RED when output 2 activated JU LU UL Fast FLASHING wrong code entered error LN LTL SLOW FLASHING in normal standby mode L ON in programming mode L ON when relay 3 activated Note Programming can only begin 60 seconds after power on Enter Programming mode The unit is now in programming mode Amber LED x will remain ON 0000 is default programmers code Note Pressing again will exit programming mode Enter new programmers code a Location 4 8 digit code Validate Record or Delete user codes Lo o Lo Lo a 10 relay 1 codes 2 add code Memory locations 1000 available 5 delete code 000 999 for relay 1 20 relay 2 codes 001 100 for relay 2 100 available 001 100 for relay 3 30 relay 3 codes 100 available Pin code 4 8 digits Validate Example Add user 31 to have access code 5555 operating relay 2 2 9 a eleik Ls ists isl ca Group 2 Add code Location 31 Pin code 5555 Validate 5 10 relay1 mat Spat Be 20 relay2 Delete code ID location to be deleted Validate 30 relay3 1 Delete a code i Delete all codes in a grou e se 9 e 10 relay1 group 20 relay2 group 30 relay3 group Super delete code Validate Programming Relay output times amp modes fo 1 9 s 9 9 9 51 relay1 0 start stop toggle mode latching 52 relay2 1 99999 seco
15. uled SMS or call from intercom 77number 77 Delete service number Dial in mode for withheld numbers or non stored numbers 1 answer the call amp wait for pass code 2 answer the call automatic iva way speec o relays Delete phone number for caller ID access will be the telephone number to be deleted 65 73 73 Delete all phone numbers for caller ID access Add engineer phone number Unit will only accept programming from this number 74 74 Delete administrator phone number 1 Delete a dialling out number where number location 1 2 or 3 N A 61 Change relay 1 trigger code 637 Change relay 1 hold code 64 7 Change relay 1 un hold release code 67 Change relay 2 trigger code 687 Change relay 2 hold code 69 Change relay 2 un hold release code 9990 Restore defaults N A gt Q je O 40 N je ey Qo fed Q O oO n n gt D Remember to begin each new SMS with pass code 12 1234 Service Commands list These commands do not require a pass code string Simply send the sms as you see it below Check reception Reply will indicate signal level 0 31 N A Check stored numbers Note no pass code needed for this command O dial out number Dial in number Check gate status Reply will indicate status of limit switch input L2 and both relays Keypad Programming only ABK models LED indicators ON when incorrec
Download Pdf Manuals
Related Search