User Manual - ATP Instrumentation
Contents
1. Hold HOLD Auto power off Automatic power off after approx 15 minutes of inactivity Power supply 1x 9V battery with type of OO6P NEDA1604 or IEC6F22 Battery life Roughly 30 hours Operating conditions 20 C 60 C 10 RH 90 RH Storage conditions 40 C 60 C 10 RH 75 RH Dimensions L x W x H 252 x 66 x 33mm Weight 568g 4 Meter Description Wind muffler microphone cover Microphone LCD display 2 Temp Humidity selection key Backlight ON OFF key HOLD key Units selection key Power ON OFF key Li MAXKLux dBA HOLD MIN KFc Function selection key DR MAX MIN C F Selection Key 12 13 14 15 Potentiometer calibration for sound level Anemometer vane and Lux probe input Temperature and Humidity sensor input External DC 9V power supply terminal positive inside and negative outside Pore size OD 3 5mm ID 1 35mm 16 17 18 Tripod bush Battery Compartment Battery Compartment screw DACO LCD Display Description Temperature Humidity reading display Battery indication Temperature unit icon Humidity unit icon Air velocity unit icon Sound level Air velocity or Light reading display Sound level unit icon D Light unit icon mo BORD m s km h ft min Knots Mph Data Hold Peter oom OOOO 000 0 DO2. MAXKLux dBA 660 6 Operating Instructions 1 Open battery cover and install a 9 volt battery in the battery compartment 2 Replace the battery cover and tighten the screw 3 Power the meter on 4 Press MODE key to select the desired function Notes When the low battery icon 1 appears replace the meters battery Hold the meter in hand or use the tripod to affix the meter in the desired location The best measuring distance is 1 to 1 5m away from the sound source to the microphone To use the AC adapter insert the plug of the adapter 3 54 into the DC 9V connector on the side panel 7 Operating Procedures 7 1 Temperature Humidity reading selection After powering the meter on press the key to select Temperature or Humidity reading 7 2 Backlight ON OFF After powering the meter on press the 2 key once and the backlight will turn on Press this key again to turn it off The backlight will automatically turn off after approximately 30 seconds of inactivity 7 3 Data Hold Press the e button once HOLD icon will appear on the LCD which indicates the data is frozen To exit from data hold mode press the button again 7 4 Units selection 7 4 1 Measuring Air Velocity 1 After entering Air Velocity mode press the ay button to select the desired units The device will cycle through m s km h ft min knots and MPH in turn 7 4 2 Measuring Light
3. O 2 After entering Light mode press the button to select Lux or Fc 7 5 Power ON OFF Turn the meter on by pressing the i button for 1 second and to turn the meter off press and hold the button for at least 3 seconds 7 6 MODE button After turning the meter on press the e button to select desired the function The device will cycle though Sound Level Air Velocity and Light in turn 7 7 MAX MIN record Whilst in measuring mode press the EG key to enter MAX MIN measurement MAX will appear on the LCD and the maximum recorded value will be displayed Press the key again MIN will appear on the LCD and the minimum recorded value will be displayed Press the key again to exit MAX MIN measurement mode 7 8 Temperature units selection When in measuring mode press the CI button to select between C or F 8 Calibration The recommended recalibration period is 1 year Calibration repairs or servicing should only be performed by ATP Instrumentation Ltd NOTE All products are calibrated before delivery 9 Notes 1 Do not store or operate the meter in high temperature or humidity 2 Remove the battery when the meter is to be stored for long periods of time to avoid battery leakage 3 Wind blowing across the microphone will affect the noise measurement Use the supplied wind muffler to cover the microphone during applications involving turbulent air 4 Keep microph
4. User Manual 5 In 1 Multi Function Environment Meter CO MAXKLux dBA HOLD MIN KFo Please read this user manual thoroughly before using this unit and keep it for your future reference Contents 1 Safety una 3 2 Introduction t E teas 4 3 Specifications aaa 5 4 Meter Description oooooomooox 7 5 LCD Display Description 9 6 Operating Instructions ooomo 10 7 Operating ProGSdures 5 c coe cete 11 S Gal BTA ON AN REAL NE 11 9 Notes ananas 14 10 Accessories ooooooocoooo Woo 14 1 ASsatety Read the following safety information carefully before attempting to operate or service the meter Use the meter only as specified in this manual otherwise the warranty may be invalidated Environment conditions Altitude less than 2000 meters RHs90 Non Condensation Operating Temperature 30 C 60 C Maintenance Repairs or servicing should only be performed by ATP Instrumentation Ltd Wipe the unit with a dry soft cloth Do not use abrasives or solvents on this instrument Safety Symbol Complies with EMC 2 Introduction The 5 In 1 Multi Function Environment Meter is designed to combine the functions of a Sound Level Meter Light Meter Anemometer Humidity Meter and Temperature Meter into one unit It is ideal for various practi
5. cal applications in professional and home use such as monitoring and collecting data of outdoor environments temperature humidity sunlight wind speed etc or testing noise and light levels for health and safety adherence in factories schools offices airports etc 3 Specifications Sound Applied standard IEC61672 1 CLASS2 Accuracy 2 0dB Display 4 digit 55mm LCD screen Resolution 0 1dB Frequency response 31 5Hz to 8 000Hz Measurement range Auto 35dB to 130dB Frequency weighting dBA Microphone 1 2 inch Electric condenser microphone Light Measuring range 0 Lux to 200 000 Lux 0 Fc to 20 000 Fc Spectral response CIE photopic CIE human eye response curve Spectral accuracy CIE VA function f1 S6 Cosine response f2 sar Accuracy 4 rdg 0 5 f s lt 10 000Lux 5 rdg 10 digits gt 10 000Lux Photo detector One silicon photo diode with filter Airflow Air velocity range 0 5m s to 30 0m s Air velocity accuracy 3 0 3d Measurement units m s km h ft min knots MPH Temperature Measurement range 40 to 70 C 40 to 158 F Accuracy 2 0 C 3 6 F Measurement units C F Resolution 0 1 Humidity Measurement range 10 to 95 RH Accuracy 5 RH Resolution 0 1 Data update 1 time per second Maximum value MAX Minimum value MIN Data
6. one dry and avoid severe vibration 10 Accessories User manual Temperature and Humidity probe Anemometer vane Lux probe Wind muffler 9V battery Adaptor Optional Tripod Optional 0004000 ATP ATP Instrumentation Ltd Tournament Way Ashby de la Zouch Leicestershire LE65 2UU Sales 01530 566800 sales atp instruments co uk Repair and Calibration 01530 566804 technical atp instruments co uk www atp instrumentation co uk
Download Pdf Manuals
Related Search