FAVORIT 78400 VI0P EN User manual
Contents
1. e If the water inlet hose is damaged im mediately disconnect the mains plug from the mains socket Contact the Service to replace the water inlet hose 1 3 Use e This appliance is intended to be used in household and similar applications such as Staff kitchen areas in shops offices and other working environments Farm houses By clients in hotels motels and oth er residential type environments Bed and breakfast type environ ments WARNING Risk of injury burns electrical shock or fire e Do not change the specification of this appliance e Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal posi tion e Do not keep the appliance door open without supervision to prevent to fall on it e Do not sit or stand on the open door e Dishwasher detergents are dangerous Obey the safety instructions on the detergent packaging e Do not drink and play with the water in the appliance e Do not remove the dishes from the appliance until the programme is completed There can be detergent on the dishes The appliance can release hot steam if you open the door while a programme operates e Do not put flammable products or items that are wet with flammable products in near or on the appliance e Do not use water spray and steam to clean the appliance 1 4 Disposal WARNING Risk of injury or suffocation e Disconnect the appliance from2. 50 Dry 4 Fresh soil Wash 60 C Quick Crockery and Rinse S N 4 cutlery 5 Normal soil Prewash OKO PLUS ECO Crockery and Wash 50 C 50 5 cutlery Rinses Dry 6 Light soil Wash 55 C Quick Crockery and Rinses ann cutlery 7 Normal or light Wash 45 C OKO PLUS Y 45 soil Rinses Delicate crock Dry ery and glass ware 8 All Prewash SUI DS 1 The appliance senses the degree of soil and the quantity of items in the baskets It automatically adjusts the temperature and quantity of the water the energy consumption and the programme duration ENGLISH 7 2 This programme has a high temperature rinsing phase for better hygiene results During the rinsing phase the temperature stays at 70 C for at least 10 minutes 3 This is the most silent washing programme The pump works at a very low speed to decrease the level of noise Because of the low speed the programme duration is long 4 With this programme you can wash a load with fresh soil It gives good washing results in a short time 5 With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil This is the standard programme for test institutes 6 Use this programme to quickly rinse the dishes This prevents the remaining food to bond on the dishes and bad odours to come out from the appliance Do not use detergent with this programme Consumption values Programme 1 Duration min
3. refer to the information that follows for a solu tion to the problem With some problems the display shows an alarm code e The appliance does not fill with water Problem 9 4 Internal cleaning If you regularly use short duration pro grammes these can leave deposits of grease and limescale inside the appli ance To prevent this we recommend to run long duration programmes at least 2 times per month Z0 The appliance does not drain the water e 3 The anti flood device is on WARNING Deactivate the appliance before you do the checks Possible solution You cannot activate the appli ance Make sure that the mains plug is connected to the mains socket Make sure that there is not a damaged fuse in the fuse box The programme does not start Make sure that the appliance door is closed If the delay start is set cancel the setting or wait for the end of the countdown The appliance does not fill with water Make sure that the water tap is open Problem ENGLISH 15 Possible solution Make sure that the pressure of the water supply is not too low For this information contact your local water authority Make sure that the water tap is not clogged The appliance does not drain the water Make sure that the filter in the inlet hose is not clogged Make sure that the inlet hose has no kinks or bends Make sure that the sink spigot is not clog
4. Energy kWh Water I 1 40 150 05 12 6 11 AUTO 45 70 2 130 150 Il 12 10 11 PRO 7 08 3 180 200 1 1 1 2 8 7 Extra SILENT 50 4 30 0 8 2 Quick 30MIN 60 5 195 0 79 8 9 ECO 50 6 50 60 09 10 7 8 Quick 50MIN 55 7 70 80 0 6 0 9 10 11 Y 45 8 14 0 1 3 ani N CA s YA 1 The water pressure and temperature the variations of the mains supply the options and the quantity of dishes can change the values Information for test institutes For all the necessary information for test performance send an email to info test dishwasher production com Write down the product number PNC that is on the rating plate 8 www aeg com 5 OPTIONS 5 1 Multitab option Activate this option only when you use the combi detergent tablets This option deactivates the flow of rinse aid and salt The related indicators are off The programme duration can increase Activating the multitab option i Activate or deactivate the multi tab option before the start of a programme You cannot activate or deactivate this option while a programme operates 1 Press the multitab button the multi tab indicator comes on If you stop to use the combi detergent tablets before you start to use separately detergent rinse aid and dishwasher salt do these steps 1 Set the water softener to the highest level 2 Make sure that the salt container and the rinse aid dispenser are full 3 Start the shortest
5. m 9 FAVORIT 78400 VIOP EN User manual WAEG perfekt in form und funktion 2 www aeg com CONTENTS 2900ng uswnn m m FOR PERFECT RESULTS Thank you for choosing this AEG product We have created it to give you impeccable performance for many years with innovative technologies that help make life simpler SAFETY INSTRUCTIONS ea a eu een E PRODUCT DESCRIPTION a sea ae ee EE CONTROL FANE Cae aain en ea nen DE acne a PROGRAMMES 2 54 22 4 0 22 ccd can aa da ded Re nn ee en a doce OPTIONS 2 2 42 Ben een du Pee ee BEFORE FIRST USE dc a ee nd ang re een DAILY USB aaike ee ee rc zei HINTS AND TIPS taco barda eG oo bode ahem a a a Heer gt CARE AND CLEANING tai ane 2222 Piles 9 her nee ee en er TROUBLESHOOTING as dde a de od TECHNICAL INFORMATION oo 20 00 sense rrr features you might not find on ordinary appliances Please spend a few minutes reading to get the very best from it Visit our website for Get usage advice brochures trouble shooter service information www aeg com Register your product for better service www aeg com productregistration Buy Accessories Consumables and Original spare parts for your appliance www aeg com shop ad amp CUSTOMER CARE AND SERVICE We recommend the use of original spare parts When contacting Service ensure that you have the following data available The information can be found on the rating plate Model PNC Se
6. programme with a rinsing phase without detergent and without dishes 4 Adjust the water softener to the wa ter hardness in your area 5 Adjust the released quantity of rinse aid 5 2 OKO PLUS This option decreases the temperature in the last rinse phase The use of this option decreases the en ergy consumption up to 25 and the programme duration The dishes can be wet at the end of the programme 6 BEFORE FIRST USE 1 Make sure that the set level of the water softener agrees with the water hardness in your area If not adjust the water softener Contact your local 5 3 Acoustic signals The acoustic signals operate in these conditions e When the programme is completed e When he level of the water softener is adjusted e When the appliance has a malfunc tion i Factory setting On It is possible to deactivate the acoustic signals Deactivating the acoustic signals 1 Press the on off button to activate the appliance Make sure that the ap pliance is in setting mode refer to Setting and starting a programme 2 Press and hold at the same time but tons Y and until the indicators Py of buttons O NV and A start to flash 3 Press button The indicators of buttons amp and V go off The indicator of button N contin ues to flash e The display shows the current set ting lb On Ob Off 4 Press button to change the set ting 5 Deacti
7. results The water softener neutralises these miner als The dishwasher salt keeps the water softener clean and in good conditions It is important to set the right level of the water softener This makes sure that the water softener uses the correct quantity of dishwasher salt and water 8 2 Using salt rinse aid and detergent e Only use salt rinse aid and detergent for dishwasher Other products can cause damage to the appliance e The rinse aid helps during the last rinsing phase to dry the dishes with out streaks and stains e Combi detergent tablets contain de tergent rinse aid and other added agents Be sure that these tablets are applicable to the water hardness in your area Refer to the instructions on the packaging of the products e Detergent tablets do not fully dissolve with short programmes To prevent 2 Q 2 Close the water tap If you do not press the on off button the AUTO OFF device automatically deactivates the ap pliance after some minutes This helps to decrease the energy consumption Important e Let the dishes become cold before you remove them from the appliance Hot dishes can be easily damaged e First remove the items from the lower basket then from the upper basket e There can be water on the sides and on the door of the appliance Stainless steel becomes cool more quickly than the dishes detergent residues on the tableware we recommend that you use the tab
8. the mains supply e Cut off the mains cable and discard it e Remove the door catch to prevent children and pets to get closed in the appliance ENGLISH 5 2 PRODUCT DESCRIPTION Upper spray arm Upper basket Lower spray arm Filters 2 1 Light beam Rating plate e When a programme operates a red Salt container light beam shows on the floor below Ai the appliance door When the pro BI Aver gramme is completed the red light Rinse aid dispenser changes to a green light E Detergent dispenser e When the appliance has a malfunc E Cutlery basket tion the red light beam flashes Lower basket 3 CONTROL PANEL o o o o o 5 O or V E se Lo ee 35 i On off button a KO PLUS button Display Multitab button Delay button E RESET button Programme button down El Indicators Programme button up 6 www aeg com Indicators Description g Salt indicator This indicator is off while the programme oper ates HE Rinse aid indicator This indicator is off while the programme operates gt End indicator 4 PROGRAMMES Programme Degree of soil Programme phases Options Type of load 1 All Prewash KO PLUS AUTO 1 Crockery cut Wash 45 C or 70 C 45 70 lery pots and Rinses pans Dry 2 Heavy soil Prewash KO PLUS PRO Crockery cut Wash 70 C 70 2 lery pots and Rinses pans Dry 3 Normal soil Prewash Extra Crockery and Wash 50 C SILENT 3 cutlery Rinses
9. the combi detergent 9 AA i tablets activate the multitab op e If the salt indicator is on fill the salt tion container 5 Set and start the correct programme for the type of load and the degree of soil 7 1 Using the detergent ENGLISH 11 Press the release button B to open the lid C Put the detergent in the compart ment A If the programme has a prewash phase put a small quantity of deter gent on the inner part of the appli ance door If you use detergent tablets put the tablet in the compartment A Close the lid Make sure that the re lease button locks into position 7 2 Setting and starting a programme Setting mode The appliance must be in setting mode to accept some operations The appliance is in setting mode when after the activation the display shows 2 horizontal status bars If the control panel shows other condi tions press RESET until the appliance is in setting mode Starting a programme without delay start 1 Open the water tap 2 Press the on off button to activate the appliance Make sure that the ap pliance is in setting mode 3 Set the programme e The related programme number flashes in the display 4 If you want you can set the options 5 Close the appliance door The pro gramme starts e f you open the door the display shows the programme duration that decreases with steps of 1 mi nute Starting a programme
10. ting of the water softener e g 6 L level 5 LY Press button amp again and again to change the setting Deactivate the appliance to confirm the setting 10 www aeg com 6 2 Filling the salt container 1 Turn the cap counterclockwise and open the salt container 2 Put 1 litre of water in the salt con tainer only for the first time 3 Fill the salt container with dishwash er salt 4 Remove the salt around the opening of the salt container 5 Turn the cap clockwise to close the salt container IN CAUTION Water and salt can come out from the salt container when you fill it Risk of corrosion To pre vent it after you fill the salt con tainer start a programme Press the release button D to open the lid C Fill the rinse aid dispenser A no more than the mark max Remove the spilled rinse aid with an absorbent cloth to prevent too much foam Close the lid Make sure that the re lease button locks into position You can turn the selector of the released quantity B between position 1 lowest quantity and position 4 highest quantity 7 DAILY USE 1 Open the water tap e If the rinse aid indicator is on fill 2 Press the on off button to activate the rinse aid dispenser the appliance Make sure that the ap 3 Load the baskets pliance is in setting mode refer 4 Add the detergent and starting a pro e If you use
11. e and electrical shock e The appliance must be earthed ENGLISH 3 e Make sure that the electrical informa tion on the rating plate agrees with the power supply If not contact an electrician e Always use a correctly installed shock proof socket e Do not use multi plug adapters and extension cables e Make sure not to cause damage to the mains plug and to the mains cable Should the appliance power supply cable need to be replaced this must be carried out by our Service Centre e Connect the mains plug to the mains socket only at the end of the installa tion Make sure that there is access to the mains plug after the installation e Do not pull the mains cable to discon nect the appliance Always pull the mains plug e Do not touch the mains cable or the mains plug with wet hands e Only for UK and Ireland The appli ance has a 13 amp mains plug If it is necessary to change the fuse in the mains plug use a 13 amp ASTA BS 1362 fuse e This appliance complies with the E E C Directives Water connection e Make sure not to cause damage to the water hoses e Before you connect the appliance to new pipes or pipes not used for a long time let the water flow until it is clean e The first time you use the appliance make sure that there is no leakage e The water inlet hose has a safety valve and a sheath with an inner mains ca ble 4 www aeg com A WARNING Dangerous voltage
12. ehold waste Return the product to your local recycling facility or contact your municipal office ENGLISH 17 18 www aeg com ENGLISH 19 www aeg com shop P Ce es I 117929051 A 212013 C m HAEG perfekt in form und funktion
13. ged The anti flood device is on Make sure that the drain hose has no kinks or bends Close the water tap and contact the Service After the checks are completed activate penser and use rinse aid together with the appliance The programme contin ues from the point of interruption If the problem occurs again contact the Service If the display shows other alarm codes contact the Service 10 1 If the washing and drying results are not satisfactory Whitish streaks or bluish layers on glasses and dishes The released quantity of rinse aid is too much Adjust the rinse aid selector to a lower position The quantity of detergent is too much Stains and dry water drops on glasses and dishes The released quantity of rinse aid is not sufficient Adjust the rinse aid se lector to a higher position The quality of the detergent can be the cause Dishes are wet The programme is without a drying phase or with a low temperature dry ing phase The rinse aid dispenser is empty The quality of the rinse aid can be the cause The quality of the combi detergent tablets can be the cause Try a differ ent brand or activate the rinse aid dis the combi detergent tablets i Refer to HINTS AND TIPS for other possible causes 10 2 How to activate the rinse aid dispenser 1 3 Press button V py The indicators of buttons amp and N go off The indicator of button V contin ues t
14. lets with long programmes Do not use more than the correct quantity of detergent Refer to the instructions on the detergent packaging 8 3 Loading the baskets i e Only use the appliance to wash items that are dishwasher safe e Do not put in the appliance items made of wood horn aluminium pew ter and copper e Do not put in the appliance items that can absorb water sponges household cloths e Remove remaining food from the items e To remove easily remaining burned food soak pots and pans in water be fore you put them in the appliance e Put hollow items cups glasses and pans with the opening down Refer to the supplied leaflet with examples of the load of the bas kets e Make sure that cutlery and dishes do not bond together Mix spoons with other cutlery e Make sure that glasses do not touch other glasses e Put the small items in the cutlery bas ket e Put the light items in the upper bas ket Make sure that they do not move e Make sure that the spray arms can move freely before you start a pro gramme 8 4 Before starting a programme Make sure that 9 CARE AND CLEANING IN WARNING Before maintenance deactivate the appliance and disconnect the mains plug from the mains sock et 9 1 Cleaning the filters ENGLISH 13 The filters are clean and correctly in stalled The spray arms are not clogged The position of the items in the bas kets is correct The pr
15. o flash e The display shows the current set ting Gd Off Ta 4 Press button V to change the set ting 5 Deactivate the appliance to confirm the setting 6 Adjust the released quantity of rinse Press the on off button to activate the appliance Make sure that the ap pliance is in setting mode refer to Setting and starting a programme Press and hold buttons V and Al at the same time until the indicators of buttons amp V and A start to flash aid 16 www aeg com 7 Fill the rinse aid dispenser 11 TECHNICAL INFORMATION Dimensions Width Height Depth 446 818 898 550 mm Electrical connection Refer to the rating plate Voltage 220 240 V Frequency 50 Hz Water supply pressure Min max bar MPa 0 5 0 05 8 0 8 Water supply 1 Cold water or hot water max 60 C Capacity Place settings 9 Power consumption Left on mode 0 10 W Off mode 0 10 W 1 Connect the water inlet hose to a water tap with a 3 4 thread 2 If the hot water comes from alternative sources of energy e g solar panels aeolian energy use the hot water supply to decrease energy consumption 12 ENVIRONMENT CONCERNS Recycle the materials with the symbol amp Put the packaging in applicable containers to recycle it Help protect the environment and human health and to recycle waste of electrical and electronic appliances Do not dispose appliances marked with the symbol 2 with the hous
16. ogramme is applicable for the type of load and for the degree of soil The correct quantity of detergent is used There is dishwasher salt and rinse aid unless you use combi detergent tab lets The cap of the salt container is tight i Dirty filters and clogged spray arms decrease the washing re sults Make a check regularly and if necessary clean them 2 Turn the filter A counterclockwise and remove it To disassemble the filter A pull apart A1 and A2 Remove the filter B Wash the filters with water Before you put the filter B back make sure that there are no residues of food or soil in or around the edge of the sump 14 www aeg com Make sure that the filter B is cor rectly positioned under the 2 guides C Assemble the filter A and put it back in filter B Turn it clockwise until it locks An incorrect position of the filters can cause bad washing results and damage to the appliance 9 2 Cleaning the spray arms Do not remove the spray arms If the holes in the spray arms are clog ged remove remaining parts of soil with a thin pointed object 9 3 External cleaning Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads or solvents 10 TROUBLESHOOTING The appliance does not start or it stops during operation Before you contact the Service
17. rial Number A Warning Caution Safety information i General information and tips ws Environmental information Subject to change without notice 1 A SAFETY INSTRUCTIONS Before the installation and use of the ap pliance carefully read the supplied in structions The manufacturer is not re sponsible if an incorrect installation and use causes injuries and damages Always keep the instructions with the appliance for future reference 1 1 Children and vulnerable people safety WARNING Risk of suffocation injury or per manent disability e Do not let persons children included with reduced physical sensory re duced mental functions or lack of ex perience and knowledge use the ap pliance They must have supervision or instruction for the operation of the ap pliance by a person who is responsible for their safety e Do not let children play with the appli ance e Keep all packaging away from chil dren e Keep all detergents away from chil dren e Keep children and pets away from the appliance door when it is open 1 2 Installation e Remove all the packaging e Do not install or use a damaged appli ance e Do not install or use the appliance where the temperature is less than 0 Es e Obey the installation instruction sup plied with the appliance e Make sure that the appliance is instal led below and adjacent to safe struc tures Electrical connection WARNING Risk of fir
18. vate the appliance to confirm the setting water authority to know the water hardness in your area 2 Fill the salt container 3 Fill the rinse aid dispenser 4 Open the water tap 5 Processing residues can stay in the 6 1 Adjusting the water softener appliance Start a programme to re Water hardness ENGLISH 9 move them Do not use detergent and do not load the baskets Water softener 1 Factory position 2 Do not use salt at this level Electronic adjustment 1 Press the on off button to activate the appliance Make sure that the ap pliance is in setting mode refer to Setting and starting a programme Press and hold at the same time but tons Y and until the indicators of buttons amp V and A start to flash 3 py Press button amp The indicators of buttons V and IN go off adjustment German French mmol l Clarke Electronic degrees degrees degrees dH fH 47 50 84 90 8 4 9 0 58 63 10 43 46 76 83 7 6 8 3 53 57 37 42 65 75 6 5 7 5 46 52 8 29 36 51 64 5 1 6 4 36 45 23 28 40 50 4 0 5 0 28 35 6 19 22 33 39 3 3 3 9 23 27 51 15 18 26 32 2 6 3 2 18 22 11 14 19 25 19 25 13 17 4 10 7 18 0 7 1 8 a 12 lt 4 lt i lt 0 7 z5 12 Py The indicator of button con tinues to flash e The acoustic signals operate e g five intermittent acoustic signals level 5 e The display shows the current set
19. with delay start 1 Set the programme 2 Press the delay button again and again until the display shows the de lay time you want to set from 1 to 24 hours e The delay time flashes in the dis play e The delay indicator is on 3 Close the appliance door The count down starts e If you open the door the display shows the countdown of the delay start that decreases with steps of 1 hour When the countdown is completed the programme starts Opening the door while the appliance operates If you open the door the appliance stops When you close the door the ap pliance continues from the point of inter ruption Cancelling the delay start while the countdown operates When you cancel a delay start the appli ance goes back to setting mode You have to set the programme again 12 www aeg com 1 Press RESET until the display shows 2 horizontal status bars Cancelling the programme 1 Press RESET until the display shows 2 horizontal status bars Make sure that there is detergent in the detergent dispenser be fore you start a new programme At the end of the programme When the programme is completed an intermittent acoustic signal operates The display shows 0 and the end indica tor comes on 1 Press the on off button to deactivate the appliance 8 HINTS AND TIPS 8 1 The water softener Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing
Download Pdf Manuals
Related Search