T3666-60A POOL ASSEMBLY AND INSTALLATION MANUAL
Contents
1. 10 24 X 5 8 ALUMINUM POOLS MACHINE SCREW WITH ALUMINUM COVERS COPING COVER BEND TABS TO SECURE TO COPING 10 24 X 5 8 FIGURE 12A A00028 A00027A A00027B 8 X 1 SELF TAPPING SCREWS ALUMINUM POOLS WITH RESIN COVERS Dau i MACHINE 222 SCREW FIGURE 12B A00029 8 X 1 SELF TAPPING SCREWS 10 X 2 SELF TAPPING SCREWS COPING UPRIGHT PLUG FITS THIS WAY ONLY Face Plate CHANNEL TOP CLIP USE OUTERMOST SET OF HOLES FIGURE 11 W00013D U L 6 FRAME STEEL POOLS WITH METAL COVERS COPING COVER ATTACHMENT FOR STEEL FIGURE 12C POOLS COPING COVER CN VY x PLUG J 10 X I SCREW 10 X 1 2 SCREW iN SNAP CAP WASHER COPING COVER J STEEL POOLS BEND TABS UP am WITH RESIN COVE 10 X 1 SCREW DO NOT USE POWER TOOLS UPRIGHT 10 ____ POOL WALL SKIMMER ASSEMBLY TEFLON PIPE ADAPTER sos p ADAPTER W00024 FIBER WASHER LINER SANDWICH GASKET e POOL WALL KS RUBBER GASKET TT A WALL FITTING A LO d DIRECTIONAL BALL bo POINT OPENING AWAY DIRECTION2. through 10 are for overlap liners only For beaded liners proceed to step 1 1 Step 7 Remove the liner from the carton and unfold into the pool Be careful not to drag abrade or snag the liner opread the liner out over the entire bottom of the pool Raise the liner sidewall Step 8 See Figure 8A and Detail 8A Place the liner over the edge of the wall Make sure the overlap is equal around the outside of the pool wall Cut the liner interlock into 2 pieces and center the pieces of the liner interlock over the wall at each upright Place the bead receiver or wall channel over the wall edge as shown to secure the liner in place Step 8A See Detail 8C for a J Bead Liner Place the J Hook bead of the liner on top of the wall and push down firmly Then place the bead receiver or wall channel over the J Bead liner and attach the top clips to the uprights Do NOT put the J Bead liner in the bead receiver WARNING Failure to use the sand or sand equivalent and shape it as specified will void all warranties on the pool and liner FIGURE 3 W00007A SEVERAL 1 4 20 S S 4 A LAYERS OF HEX NUT ZN 26 P P d 1 4 20 X 3 4 S S e PA MACHINE SCREWS ell ko JULII OF POOL WALL pep i 7 0 7 1 4 20 S S IH LI i OUTSIDE OF pr WOK ENCLOSURE MACHINE 0 u B ZE NOTE Start wall enclosure strip at the bo
3. TO LIABILITY ARISING FROM INJURY CLAIMS A NO DIVING COPING TWO SUPPLIED THESE ARE TO BE INSTALLED ACROSS THE POOL FROM THE POINT OF ENTRY AND HAVE ONE SECTION OF REGULAR COPING BETWEEN THEM COPING WITH INTERNATIONAL LOGO THIS ONE COPING IS TO BE INSTALLED AT THE POINT OF ENTRY EITHER ADJACENT TO THE LADDER UNDER THE IN POOL LADDER OR IN THE CENTER OF A DECK DANGER AREA SIGN WITH LOGO T1440 THIS SIGN MUST BE INSTALLED AT THE POINT OF ENTRY FACING ALL USERS AS THEY ENTER THE POOL IF YOUR POOL HAS A FENCE THE SIGN IS TO BE FASTENED TO THE FENCE ADJACENT TO THE LADDER OR ENTRANCE IF YOUR POOL DOES NOT HAVE A DECK OR FENCE ATTACH THE SIGN TO THE EDGE OF THE COPING ADJACENT TO THE LADDER THE SIGN MUST BE VISIBLE TO ALL USERS AS THEY ENTER THE POOL AREA CAUTION SAFETY RULES SIGN 1445 THIS SIGN MUST BE ATTACHED TO THE FENCE DIRECTLY BELOW THE DANGER SIGN OR IF YOU DO NOT HAVE POOL FENCING ON THE COPING NEXT TO THE DANGER SIGN If any signs are missing or damaged contact the customer service department for replacements CAUTION 1 DECK SURFACES MAY BECOME SLIPPERY WHEN WET DO NOT RUN OR DIVE INTO THE POOL FROM THE DECK NOTE SUNTAN LOTIONS AND OILS MAY CAUSE POOL COMPONENTS TO BECOME SLIPPERY 2 EACH MONTH CHECK THE POOL WALL FOR DETERIORATION OR LEAKAGE ESPECIALLY AT THE SKIMMER AND RETURN FITTINGS THE SKIMMER AND RETURN GASKETS SHOULD BE REPLACED EACH SPRING TO PREVENT LEAKAGE DETERIORATION CAN WEAKEN THE POOL WALL WH
4. TO REDUCE THE CHANCE OF A CHILD ACCESSING AN UNSUPERVISED POOL THE BARRIER MAY BE A FENCE WALL OR COMBINATION THEREOF WHICH COMPLETELY SURROUNDS THE POOL BARRIERS MUST COMPLY WITH THE LOCAL BUILDING CODE BOCA NATIONAL BUILDING CODE OR THE CONSUMER PRODUCT SAFETY COMMISSION BARRIER STATEMENT THE FOUR FOOT HIGH POOL WALLS USUALLY PROVIDE THIS BARRIER HOWEVER IF THE POOL IS LESS THAN 48 ABOVE GRADE OR HAS BUTTRESSES OVAL POOLS YOU MAY NEED ADDITIONAL FENCING TO PROVIDE THIS BARRIER CONSULT WITH YOUR BUILDING OFFICIAL FOR SPECIFIC REQUIREMENTS FENCING OPTIONS ARE AVAILABLE FOR YOUR POOL PLEASE CONTACT YOUR POOL DEALER YOU MUST MAINTAIN A 5 WIDE CLEAR ZONE AROUND THE POOL AND DECK OR FENCING DO NOT ALLOW TOYS CHAIRS TABLES OR SIMILAR CLIMBABLE OBJECTS IN THIS CLEAR ZONE ENABLING CHILDREN TO CLIMB AND GAIN ACCESS TO THE POOL THE FILTER EQUIPMENT MUST ALSO BE LOCATED OUTSIDE OF THE CLEAR ZONE 4 YOU MUST RAISE AND LATCH OR SECURE YOUR POOL LADDER OR POOL ENTRANCE WHEN THE POOL IS NOT IN USE Adherence to the above items will reduce the frequency of preventable child drownings in swimming pools WARNING YOUR POOL IS SUPPLIED WITH WARNING SIGNS WHICH MUST BE AFFIXED TO THE POOL AS SPECIFIED IF YOU BUILD A DECK THE TWO AREA SIGNS MUST BE AFFIXED TO THE DECK AT THE POINT OF ENTRY VISIBLE TO PEOPLE ENTERING THE POOL AREA FAILURE TO INSTALL OR IMPROPER LOCATION OF SAFETY INFORMATION WILL SUBJECT YOU AND OR THE INSTALLER
5. 13666 60A POOL ASSEMBLY AND INSTALLATION MANUAL Above Ground 52 Round Pools Note Deck and fence accessories shown are optional THIS MANUAL EXPLAINS THE CORRECT METHOD TO ASSEMBLE YOUR NEW SWIMMING POOL READ THESE INSTRUCTIONS AND STUDY THE ILLUSTRATIONS ALSO READ INSTRUCTIONS FOR ACCESSORIES SUCH AS FILTERS LADDERS ETC PAY PARTICULAR ATTENTION TO THE CAUTIONS ON THE FOLLOWING PAGES THE MANUFACTURER IS NOT AFFILIATED WITH ANY PROFESSIONAL POOL INSTALLER THEREFORE THE MANUFACTURER CANNOT ASSUME RESPONSIBILITY FOR ERRORS IN THE INSTALLATION OF YOUR POOL BY THE INSTALLER OR THE HOMEOWNER IF YOU HAVE THIS POOL INSTALLED BY OTHERS PLEASE SUPERVISE TO BE SURE YOUR POOL IS INSTALLED PROPERLY AND THAT ALL THE CAUTIONS LISTED THROUGHOUT THIS MANUAL HAVE BEEN FOLLOWED PAST EXPERIENCE OR SHORT CUTS MAY NOT BE COMPATIBLE WITH OUR POOLS FOLLOW THE INSTALLATION MANUAL THE MANUFACTURER RESERVES THE RIGHT TO CHANGE OR IMPROVE ANY ITEM WITHOUT INCURRING ANY OBLIGATION TO MAKE ANY CHANGES OR IMPROVEMENTS ON ITEMS PREVIOUSLY SOLD AND TO DISCONTINUE MODELS OR CHANGE SPECIFICATIONS AT ANY TIME WITHOUT NOTICE THIS PRODUCT IS SOLD WITH A LIMITED WARRANTY THE TERMS AND CONDITIONS ARE SET FORTH IN THE LIMITED WARRANTY CERTIFICATE PACKED WITH EACH POOL COPIES OF THE LIMITED WARRANTY ARE ALSO AVAILABLE UPON WRITTEN REQUEST YOUR LOCAL BUILDING CODE MAY REQUIRE OBTAINING A BUILDING PERMIT AND MAY HAVE REQUIREMENTS ON SETBACKS BARRIERS ETC A
6. AL RETURN ASSEMBLY FROM SKIMMER BALL FITTING POOL WITH FRAME LADDER AND FENCE FIGURE 14A SA00004 POOL WITH LADDER NOTE Refer to Page 2 Warning section for Label Letter Designation DANGER When a filter or any other electrical device is added to this pool it is the responsibility of the purchaser to take all necessary precautions as set forth in article 680 of the National Electrical Code and local electrical codes Failure to comply with this requirement may result in a dangerous or hazardous electrical condition which may cause bodily injury or death 11 installing a fence or deck refer to those manuals for proper placement of safety information Step 21 Fill the pool up to the center of the skimmer make sure that all fasteners are tightened properly and your pool is completely assembled Please read The Sensible Way to Enjoy Your Pool booklet and enjoy years of swimming and relaxation d Ncc B B Pi WATER SIDE DANGER SE C amp D 2 N A Bs y y E X C DANGER Y J f CAUTION JT MEE oe a D FIGURE 14B SA00003B ADD
7. ICH COULD RUPTURE RELEASING THE POOL WATER WHICH COULD CAUSE BODILY HARM AND PROPERTY DAMAGE 3 FOR NIGHTIME USE YOU MUST PROVIDE LIGHTING TO ILLUMINATE THE POOL SAFETY SIGNS AND DECK SURFACES LIGHTING MUST COMPLY WITH ARTICLE 680 OF THE NATIONAL ELECTRIC CODE IT IS IMPORTANT THAT USERS BE ABLE TO SEE THE SHALLOW DEPTH OF THE POOL AT ALL TIMES 4 THE FOLLOWING BASIC LIFESAVING EQUIPMENT MUST BE ON HAND AT ALL TIMES A ALIGHT BUT STRONG POLE SHEPHERD S CROOK NOT LESS THAN 12 LONG B A 1 4 THROWING ROPE AS LONG AS 1 1 2 TIMES THE MAXIMUM WIDTH OF THE POOL WHICH IS ATTACHED TO A COAST GUARD APPROVED FLOTATION DEVICE SUCH AS A RING BUOY C A TELEPHONE SHOULD BE NEARBY WITH A LIST OF EMERGENCY TELEPHONE NUMBERS SUCH AS POLICE amp AMBULANCE 2 5 ADDITIONAL POOL SAFETY RELATED PUBLICATIONS ARE AVAILABLE FROM THE FOLLOWING NATIONAL SPA AND POOL INSTITUTE CONSUMER PRODUCT SAFETY COMMISSION 2111 EISENHOWER AVE WASHINGTON DC 20207 ALEXANDRIA VA 22314 IMPORTANT INSTALLATION ITEMS 1 LEVELNESS POOL MUST BE LEVEL WITHIN 3 4 UNLEVEL POOLS PLACE EXTREME FORCES ON THE POOL WHICH MAY DEFORM 2 WALL CLOSURE THE POOL WALL MUST BE FASTENED TOGETHER PROPERLY WITH BOTH BARS AND FASTENERS IN ALL HOLES OMITTED BARS OR FASTENERS CAN CAUSE THE WALL TO RUPTURE DESTROYING THE POOL AND INJURING PEOPLE 3 SAND COVE THIS SUPPORTS THE LINER AND MUST BE PACKED SOLID IF IT COMPRESSES SHIFTS OR ERODES THE LINER MAY RUPTURE RELEASING A
8. ITIONAL DANGER SIGN SEE SIDE DECK MANUAL A POINT OF ENTRY lt 1 C amp D
9. L TAPPING i a SCREW FIGURE 9 FIGURE 9B 9B UPRIGHT m 7 A00005C Steps 11 through 13 are for beaded liners only For overlap liners proceed to step 14 BEADED LINERS Step 11 See Figure 8B Detail 8B and Figure 10 Place the bead receiver on the wall Tape the joints of the bead receiver using fabric tape to protect the liner Place the top clips on the uprights The support brackets if provided must be inserted into the round end uprights and rotated upward prior to installation of coping Attach using one screw for the bracket and top clip and two additional screws for the top clip Step 12 Remove the liner from the carton and unfold into the pool Be careful not to drag abrade or snag the liner Spread the liner out over the entire bottom of the pool Raise the liner side wall and place the bead into the bead receiver Bead must be fully seated in the receiver to prevent it coming out later when being filled Check it frequently while filling pool Step 13 Smooth all the wrinkles out on the bottom of the liner To remove wrinkles always pull the liner firmly but gently No sharp tugs Be certain liner is centered Time spent removing wrinkles and aligning the liner will give vou a neater looking and easily maintained pool DUCT TAPE LINER BEAD NOTE If the liner is exposed to the sun for a long time it BRR will stretch and cause wrinkles This can be avoided by BEAD waiting until dusk or by spraying co
10. LL THE WATER AND DESTROYING THE POOL AND INJURING PEOPLE THESE POOLS ARE NOT DESIGNED TO BE BURIED THE GROUND FORCES CAN COLLAPSE THE POOL INWARD DO NOT LOCATE YOUR POOL NEAR STRUCTURES SUCH AS A HOUSE GARAGE ETC AS PEOPLE COULD DIVE OR JUMP INTO THE POOL RESULTING IN DEATH OR PERMANENT INJURY 6 ALTHOUGH THERE ARE RELATIVELY FEW PARTS IN YOUR POOL NONE MAY BE OMITTED IN ASSEMBLY EACH PART SUPPLIED IS AN IMPORTANT PART AND IF OMITTED MAY CAUSE POOL FAILURE CHECK ALL PARTS AGAINST THE PARTS LIST WARNING Do not exceed the following torque values for the noted fasteners 1 4 20 S S Fasteners 75 in Ibs 3 8 16 S S Fasteners 236 in lbs 3 8 16 Aluminum Fasteners 143 in Ibs TOOLS AND MATERIALS PHILLIPS SCREWDRIVER 2 HAND TROWEL EXTENSION CORDHAMMER RAKE SLOTTED SCREWDRIVER 2 GARDEN HOSE amp NOZZLE STRING LINE PLIERS SOCKET WRENCH amp SOCKETS 50 TAPE MEASURE HAND TAMPER TORQUE WRENCH TRANSIT OR FARM LEVEL ELECTRIC DRILL amp BITS GARDEN SHOVEL WRENCHES 1 LONG STRAIGHT 2X4 14 LONG 1 ROLL DUCT OR FABRIC TAPE 25 WOOD STAKES CAN WHITE SPRAY PAINT SAND AND BLOCK CHART SAND 2 x 8 x 16 4 x 8 x 16 POOL SIZE TONS YARDS PATIO BLOCKS CAP BLOCKS 15 2 1 1 4 10 18 2 1 2 1 3 4 12 NOTE Sand must be 21 3 1 2 2 1 4 14 masons or bar sand and 24 4 1 2 3 16 be free of foreign objects 27 5 3 4 3 3 4 18 30 6 5 20 SELECTING THE POOL SITE 1 Check your local building codes and acquire proper bu
11. NOTE If the liner is exposed to the sun for RECEIVE a long time it will stretch and cause LINER wrinkles This can be avoided by waiting INTERLOCK until dusk or by spraying cold water on the liner during installation So ul RECEIVER LINER Step 9 Smooth all the wrinkles out on DARZ OVERLAP the bottom of the liner To remove LINER wrinkles always pull the liner firmly but J BEAD gently No sharp tugs Be certain liner is centered Time spent removing wrinkles ecd POOL and aligning the liner will give you a SNF WALL neater looking and easily maintained DETAIL 8A pool Step 10 See Figure 9A and 9B For aluminum pools only install captive nuts on top clips If you have a steel pool attach the top clips as shown Note the support bracket is only used on 6 steel frames Lift up one end of the bead receiver and slide the top clip onto it as shown in Figure 9B Slide the top clip completely onto DETAIL 8C POOL WALL DETAIL 8B the first bead receiver Then push it down onto the wall Next slide the top clip _ TOP CLIP over the adjacent bead receiver until the ends of the bead receiver is centered into _4 the top clip 10 X 2 KS CAPTIVE SELF BEAD 0 16 TAPPING RECEIVER NUT _ Ans SCREW 2 pm Tu Z 6 E JK ALUMINUM k 4 POOLS S SUPPORT Sa S NN FOR STEEL BRACKET v 10X POOLS 6 STEEL N SELF FRAMES ONLY LI
12. NY HOME BUILT OR PREFABRICATED DECKS SHOULD CONFORM TO THE LOCAL CODES AND BOCA NATIONAL BUILDING CODE THE ELECTRICAL CODE MAY REQUIRE A PERMIT AND INSPECTION AND USE OF GFCI DEVICES OR OTHER CONDITIONS THE ELECTRICAL INSTALLATION MUST ALSO CONFORM TO ARTICLE 680 OF THE NATIONAL ELECTRIC CODE INSTALL THE FILTER AND PUMP IN ACCORDANCE WITH THE MANUFACTURERS INSTRUCTIONS ARTICLE 680 STATES THAT YOU MUST BOND THE SWIMMING POOL PUMP TO THE SWIMMING POOL THIS CAN BE DONE BY ATTACHING A Z8 COPPER WIRE FROM THE BONDING LUG ON THE PUMP TO AN UNPAINTED METAL SURFACE ON THE POOL WALL OR BOTTOM CLIP THE INSTALLATION OF AN ABOVE GROUND SWIMMING POOL WILL USUALLY REQUIRE THREE PEOPLE TO HELP ASSEMBLE IT DANG EH THIS POOL EVEN IF SUPPLIED WITH A DEEP AREA CONFORMS TO THE NATIONAL SWIMMING POOL INSTITUTE STANDARDS FOR A TYPE O NON DIVING POOL DIVING SLIDING OR JUMPING INTO THE POOL MAY CAUSE PARALYSIS DEATH OR PERMANENT INJURY CUSTOMER SERVICE DEPARTMENT 8600 RIVER ROAD DELAIR NEW JERSEY 08110 3398 USA DANGER 1 DO NOT DIVE OR JUMP INTO YOUR POOL DO NOT USE A POOL SLIDE ON THIS POOL YOUR POOL CONTAINS SHALLOW WATER AND IS NOT DESIGNED FOR HEADFIRST ENTRY DIVING OR SLIDING OR JUMPING DIVING SLIDING OR JUMPING CANRESULT IN A BROKEN NECK IF YOU STRIKE THE POOL THIS CAN RESULT IN PARALYSIS DEATH OR PERMANENT INJURY INFORM ALL FAMILY AND GUESTS OF THESE RULES AND POINT OUT WARNING LABELS IT IS NECESSARY TO MAINTAIN A 4 HIGH BARRIER
13. TOM WALL position them the FIGURE 1 CHANNEL circle Place a patio L00033A X 8 X 16 block under each PATIO BLOCK bottom clip If the FOLLOWS bottom wall channel is LINE 2 on soft ground place 9 additional blocks in a FOR ALUMINUM POOLS pyramidal shape under SMALL BOTTOM the bottom clips for STAKE CLIP gt BOTTOM WALL e VA 0333 CHANNEL FOR STEEL POOLS Dig 2 down for each block The top of each 2 X 8 X 16 block must be at grade level When leveling FOLLOWS LINE 2 PATIO BLOCK the blocks never build up always dig down NY Place a stake at the center of each wall channel to keep the circle round during installation Step 3 See Figure 3 4 and 5 Place the required amount of sand inside the pool area Starting at the center of a bottom clip insert the pool wall into the wall channel around the entire pool area Make sure the skimmer and return cutout are at the top of the wall and not over a clip or upright Attach the pool wall ends together as shown using the two 2 wall enclosure bars and hardware The heads of the machine screws must be on the inside of the wall Do not omit any fasteners in the pool wall connection The wall will not stay together without all the fasteners Cover the bolt enclosure on the inside with several layers of duct tape to protect the liner If either wall enclosure strip is missing damaged or do not align properly with all holes in the wa
14. ilding permits For poor soil conditions consult a professional engineer 2 The pool site must be absolutely level and solid The area must be free from stones and roots 3 To protect the pool from chemicals and foreign matter in the soil you may use a ground cover under the sand base Do not install your pool on asphalt tar paper grass wood gravel clay or concrete or treated soils 4 Position your pool away from trees overhead wires structures such as a house or garage or septic field GROUND PREPARATION Your pool must be installed on a solid level surface Position stakes as shown on figure 1 and use a farm level or transit to level the area shown Remove all grass roots and stones Start at the lowest spot level outwards do not fill in low spots The area must be absolutely level The following table refers to Figures 1 and 3 on the next page ROUND POOLS LINE 1 LINE 2 15 0 8 6 7 6 18 20 10 0 9 0 217207 11 6 10 6 24 0 13 0 12 0 97 p 14 6 13 6 30 0 16 0 15 0 SECTION II POOL CONSTRUCTION Step 1 Parts A N SLOT SIDE UP Identification See GROUND figures in bill of material UA packet Check for ROOTS STONES AND DEBRIS installation addendums Step 2 See Figures 1 o SUAE and 2 and table on page TRANSIT STAKE 3 Scribe a circle defined by line 1 Slide the wall channels into the bottom clips and BOT
15. ld water on the liner RECEIVER during installation WALL M FIGURE 10 W00023 Step 14 Begin to fill the pool with water Use a slow stream of water and fill approximately 1 1 2 deep Make sure the fit of the liner is correct smooth out any wrinkles in the pool bottom If installing a deck do not fill more than 12 until the deck is installed Step 15 Fill the pool with 4 to 6 of water Measure the distance from the coping to the water surface at several points around the pool to be certain that the pool is still level WARNING The pool must not be more than 3 4 out of level If the pool is not level drain the water and level the structure Any non compliance with this requirement will void all warranties Step 16 See Figure 14 Locate the safety warning copings as described and as shown at the back of this manual Attach coping as shown To the outermost set of holes in the top clip Step 17 At each upright attach the coping and coping covers as shown in Figures 11 12A 12B and 12C Position the coping with warning labels as shown in Figure 14A and Figure 14B Step 18 Fill the pool until the water level is 3 inches below the return hole Step 19 Follow the instructions for the filtration system skimmer and return that are supplied with the filter Step 20 Attach the remaining safety warning signs as described and shown in Figure 14A and B If COPING COVER ATTACHMENT FOR ALUMINUM POOLS
16. ll do not use the wall and notify your dealer at once CAUTION Installation of the wall in any other manner than precisely described above will cause NOTE f the wall does not stay in the wall channel the ground is not level remove the wall and level the wall extensive damage to the pool and may result in channel injury or death to those people in or around your pool After the pool wall is assembled check the dimensions of the pool to insure that it has not shifted during assembly Step 4 See Figure 6 Attach the uprights to the bottom clips as shown If pool is provided with feature strips see addendum in Bill of Material packet Step 5 See Figure 6 and Detail 6a Install the skimmer throat gasket to each side of the pool wall and attach the skimmer to the wall as shown using hardware provided with the skimmer Mount the skimmer at the center with only two 2 pan head screws at this point Refer to skimmer instruction sheet If a pool fence or deck is to be installed read those manuals before proceeding Check care and maintenance manual for proper placement of safety information Step 6 See Figure 7 Spread the sand across the entire bottom of the pool Moisten and the sand to provide a solid base The sand base must be 2 deep after tamping The sand should be moistened and trowel to a smooth finish Create a 6 radius cove along the wall as shown This cove must also be tamped solid to prevent shifting
17. ttom hole on the wall If the enclosure strip does not cover the last hole at the FIGURE 5 top of the wall you should attach with a 20 x 34 machine L00036D SCREWS FOR ALUMINUM SKIMMER POOLS THROAT GASKET VINYL ES SKIMMER GASKET CORK ra UPRIGHT BOTTOM CLIP LOW PROFILE FRONT ACCESS SKIMMER 10 X SELF TAPPING SCREWS 4 PER UPRIGHT WO00025 NOTE THE SKIMMER THROAT GASKET MUST SANDWICH THE WALL LE ONE FLAP OF THE GASKET MUST BE ON THE INSIDE OF THE WALL AND THE OTHER ON THE OUTSIDE SKIMMER THROAT GASKET WALL PAN HEAD FOR STEEL SCREWS POOLS DETAILGA 6A SKIMMER THROAT W00030 GASKET Y s VINYL An d wo SKIMMER n AL I T IEEE q N GASKET N coo 2 ZR z X N CORK ZY NN ge Co 99 2 M UPRIGHT i ZN yr REESE creer S EXC m 7 BOTTOM CLIP am UJ LOW PROFILE FRONT ACCESS SKIMMER DIMENSIONS ARE TO TOP 10 X 4 SEL OF WALL TAPPING SCREWS 6 PER UPRIGHT WALL 2 FIGURE 7 WALL CHANNEL MOB 2 SAND BASE LINER WALL CHANNEL INTERI OCK BEAD N RECEIVER NOTE LINER BOTTOM LINER SHOULD BE CENTERED INTERLOCK ON THE POOL USING THE 24 SEAM AT THE PERIMETER t OF THE BOTTOM AS GUIDE A V SAND BASE 4 WALL FLOOR SEAM WALL FI GU RE 5 A W00023 CHANNEL W00001 AD
Download Pdf Manuals
Related Search