Nemesis-TCS 'Traction Control System Installation manual
Contents
1. module and the dashboard ECU Wiring Front link Connector P should be routed along the RIGHT side of the bike all the way to connect up with 2A from the front loom Copyright Competition Systems Ltd 2012 Competition Systems Ltd UK Tel 0044 0 8707 444666 Fax 0044 0 8707 444888 E mail mail competitionsystems co uk www competitionsystems co uk Installation TCS4C_ ZX10 2010 AB revision 01 21 01 12 Author Mick Boasman Wiring Battery connections This vital connection M must be connected directly to the battery negative connector not to the engine block or any other ground source IMPORTANT Failure to fit the ground securely can lead to misfire engine not starting TCS module damage This is the main power ground for the coil system Wiring Quick shifter input Connector Q is available for use with most type of OFF ON switch type quick shifter Pin 1 Vbat power Pin 2 Ground Pin 3 Signal For more information on quick shifter connections please refer to the System manual Wiring Coil correction device The module shown in this picture must be plugged in at all times via the 6 way connector R Without this the bike will stop within 2 seconds and identify an ignition coil error The module requires no special mounting or orientation and may be tucked into any suitable space on the rear of the bike Wiring TCS module and ground Connect the main wiring loom to the2. wire This wiring is designed to be routed along the RIGHT side of the bike after the removal of the air box Do not cable tie the wiring in place until all wiring is laid within the bike and connected Wiring Front Throttle The throttle input is the wire 2B of this loom needs to be attached to the yellow white signal_wire of the brown 16 way multi block connector located at the rear of the throttle body using the red quick link provided in the kit Attach the quick link as shown in the steps on the next page Note that the signal wire is supplied long and may be shortened as necessary Copyright Competition Systems Ltd 2012 Competition Systems Ltd UK Tel 0044 0 8707 444666 Fax 0044 0 8707 444888 E mail mail competitionsystems co uk www competitionsystems co uk Installation TCS4C_ ZX10 2010 AB revision 01 21 01 12 Author Mick Boasman Throttle connection continued The quick link is made up of three parts as seen here on the right Using the green section with the slot push it over the throttle signal wire of the bike loom until the wire rests at the bottom of the slot The large red centre section must be fitted the correct way around or the link will not work Locate the end with the sharp pointed tip protruding from the end of the outer body and screw this end onto the green section until it rests firmly against the wire The sharp tip will pierce the outer sleeve but not sever t
3. Competition Systems Ltd UK Tel 0044 0 8707 444666 Fax 0044 0 8707 444888 E mail mail competitionsystems co uk www competitionsystems co uk Installation TCS4C_ ZX10 2010 AB revision 01 21 01 12 WEMESS KS Nemesis TCS Traction Control System Installation manual Kawasaki ZX10 2008 gt 2010 with race seat and performance exhaust without motor valve This application is designed for use with the Kawasaki ZX10 2008 2010 model fitted with race seat fairing and the exhaust valve motor removed Speed pick up components Part No Checked Qty Front wheel speed sensor mounting bracket CSD1375 Spacer OD 12 8 ID 8 2 L 7 5 CSD1430 M8 x 50 Cap head screw zinc CSF1054 Speed sensor 23813030401 M6 x 16 Zinc Hex head cap screw Speed sensor CSP1019 Traction module components Part No Checked Qty Traction Control Module 4c CSP1048 Coil simulator module CSP1050 Kawasaki ZX10 2010 TCS mount CSD1428 TCS 4C Standard back panel CSD1337 Bobbin dia 10 x 17 M4 female CSP1046 M4 x 8 button head allen screw s s CSF1045 M4 Spring washer s s CSF1050 Double sided glue pad apply to sides of bracket CSD1428 CSP1020 NM Oo AR A aA aA oa Wiring Part No Checked Qty Main Wiring Kawasaki ZX10 2010 CSW 1429 Front Wiring CSW 1371 Throttle speed signal quick link red CSP1015 Display module components Part No Checked Qty Display module TC Pod Spacer 11mm Dia x 6 5 CS1258 M6 x 35 s s cap head screw black CSP1016 Push butt
4. TCS module It is vitally important that the small ground wire with the 4mm eye N be connected securely to the M4 stud using the M4 Nyloc nut Without this the module or coils could be damaged as well as TCS not functioning correctly The TCS module mounting bracket and TCS module are held together using the 4 rubber mounts screws washers and brackets shown here and in the images on the next page Note that the mounting location circled here for the exhaust valve motor must be shortened by 5mm to provide clearance for the TCS module The mounting plate should be secured to the sub frame using the double sided adhesive on the panel and cable ties at the locations shown IMPORTANT Failure to fit the module in the orientation shown and mounted on a horizontal axis will significantly affect the functionality of the TCS system if any adjustment is necessary use M4 plain washers under the rubber mounts Copyright Competition Systems Ltd 2012 Competition Systems Ltd UK Tel 0044 0 8707 444666 Fax 0044 0 8707 444888 E mail mail competitionsystems co uk www competitionsystems co uk Installation TCS4C_ ZX10 2010 AB revision 01 21 01 12 Author Mick Boasman View from left side of the bike Front is to the left View from top Front is to the left Module MUST be horizontal after installation View from underneath Front is to the left Angle view from rear right underside Components are show
5. are M6x16 dome cap screw a i shown in different e Check the gap between the sensor face and the surface colours for clarity of one of the new disc bolts set to 1mm to 2 5mm and now tighten the two M8 bolts to the manufacturers recommended torque e The sensor maximum range is approx 4mm for smaller targets and 6mm for larger targets therefore no other ferrous objects should be installed anywhere near this sensor e These are safety critical components and could result in wheel locking brake failure or TCS damage if fasteners come loose IMPORTANT Care should be taken when using paddock stands not to damage the wiring or sensor mounting Copyright Competition Systems Ltd 2012 Competition Systems Ltd UK Tel 0044 0 8707 444666 Fax 0044 0 8707 444888 E mail mail competitionsystems co uk www competitionsystems co uk Installation TCS4C_ ZX10 2010 AB revision 01 21 01 12 Author Mick Boasman Wiring The wiring provided in this kit comes in 2 parts to simplify the installation and enable crash damaged parts to be replaced without a major strip down It is recommended that the front wiring loom be installed first Wiring Front section The front section wiring part No CSW1371 has connections for all of these elements e 2C Front speed sensor 2F TC Pod display 2G Pit lane speed limiter switch 2E PC communication point 4 way AMP 2A Chassis link 2B Throttle signal single
6. e away the responsibility of the rider to operate the bike correctly within their own abilities the track conditions and the laws of physics The system is designed to achieve greater on track performance by the use of power modulation during wheel slip events but in no way should it be considered possible for the system to recover from every conceivable loss of grip The onus for safety always rests with the rider to stay within his or her own abilities and to ensure that the on bike equipment is programmed setup correctly and an appropriate TC level selected for the skill of the rider the bike and the track conditions This equipment is intended for racing or track day performance use only and where exhaust emission controls are not applicable By installing and using the Nemesis TCS you automatically indemnify Competition Systems Ltd our suppliers and our authorised dealers from all first party or third party loss or damages Normal components warranty is not affected Preparation Remove these parts from the bike e All fairing panels e Fuel tank e Air box and intake e Seat fairing TC Display pod Fitting e Mount the display pod to the bracket using the M3x8mm screws e This bracket for mounting the display is supplied straight For optimum installation on the Kawasaki you should bend this until the display is aligned correctly as seen here e Fit the angled bracket to the upper triple clamp bolt using the 9 5mm spacer and l
7. he inner core of the wire Strip back the sleeve of the throttle input wire on the TCS loom so that 8mm of inner metal core is exposed Push this into the red cap as seen here on the right with inner core showing Screw this cap and wire into the main body ensuring that metal inner core and wire cores are sandwiched and held securely Shrink sleeving can be put over this quick link if required Wiring Front TC Pod display Connect the front wiring loom to the TC Pod display via the 8 way connector 2F Wiring Front front wheel speed Route the front speed wiring 2C across the front of the bike and following the same route as the brake line to the left calliper connect it to the front soeed sensor The wiring for sensor must be routed taking all of the following into consideration e Movement of forks e Rotation of the steering e Positioning of paddock stands Wiring Front PC connector The 4 way PC connector should remain accessible but securely cable tied to the existing harness Avoid water ingress at this connector Wiring Front Pit limiter switch The 2 way pit limiter switch connector can be cable tied out of the way if not needed or plugged into the dedicated red switch assembly CSP1041 shown in this picture not supplied as part of the kit Copyright Competition Systems Ltd 2012 Competition Systems Ltd UK Tel 0044 0 8707 444666 Fax 0044 0 8707 444888 E mail mail competitionsystems co uk w
8. n in different colours for clarity only Spring washer to be used on all M4x8 screws A yos This washer is a not shown in these graphics Connector to the right side Cable ties here of the bike PC Setup Your TCS module should be loaded with the following bike BIKE KAWA ZX10_10 BIKE TYRE To suit your installation CONFIG TCS _4C Base _ 35 02 CONFIG Standard rear sprockets for maps are 17 41 Gear box output shaft teeth count 30 Status Position offset value Stronger 0 21 to 0 32 Refer to WinTC View Data Normal 0 32 to 0 37 Refer to WinTC View Data Weaker 0 37 to 0 47 Refer to WinTC View Data Note The WinTC installation guide can be found in the manual Win TC 4C manual_v2 05_a pdf Copyright Competition Systems Ltd 2012
9. on assembly blue green TC Pod CS972 TC Pod mount bkt tripple clamp CSD1399 spacer D12 8 ID8 2 L9 5 CSD1384 M8 x 40 Cap head screw zinc CSF1065 M3 x 8 Hex button head CSP1018 No _ _ Miscelaneous components Part No Checked Qty Cable ties 200mm x 4mm CSP1021 Printed TCS system manual Printed Kawasaki ZX10_2010 AB manual Nemesis TCS stickers CSP1022 Copyright Competition Systems Ltd 2012 Competition Systems Ltd UK Tel 0044 0 8707 444666 Fax 0044 0 8707 444888 E mail mail competitionsystems co uk www competitionsystems co uk Installation TCS4C_ ZX10 2010 AB revision 01 21 01 12 Author Mick Boasman IMPORTANT To be read by ALL installers and owners Notes e This kit is designed for use on bikes fitted with a race type seat fairing and standard rear speed pick fitted into the gearbox with 23 30 ratio in 6 gear The bike must also have the exhaust valve motor removed to enable sufficient space to fit the TCS module e Power for the TCS system is via the Kill switch After Kill ON bike in Run position the TCS system needs 3 seconds to boot up the engine will not start during this period e This kit uses the rear speed sensor on the gearbox output shaft front sprocket For customers who are not using our default sprocket ratio of 17 41 you will need the additional WinTC programming tool to change this Terms of use The presence of the Nemesis TCS does not tak
10. onger bolt we provide e The wiring can be secured to the ignition switch to damp out some vibration e Take care to ensure full steering movement without collision with the display pod e Mount the CS972 switch assembly to the clutch lever assembly cylinder clamp using the M6x35 bolt and spacer provided Connect the CS972 switch assembly to the TC Pod via the 4 way connector of the TC Pod wiring e Do not secure any wires in place at this stage as there will be further wires added in this region e If installing a pit limiter switch mount it on the right brake lever assembly CSD1399 O s Copyright Competition Systems Ltd 2012 Competition Systems Ltd UK Tel 0044 0 8707 444666 Fax 0044 0 8707 444888 E mail mail competitionsystems co uk www competitionsystems co uk Installation TCS4C_ ZX10 2010 AB revision 01 21 01 12 Author Mick Boasman Front Wheel Speed Your TCS kit comes with a dedicated bracket sensor and spacers to pick up from the standard disk bolts This system is designed to use the standard low height ferrous bolts titanium or stainless bolts may not be used e Remove the two M8 spindle clamp bolts from the left fork leg Use the two new longer M8x50mm bolts spacers and bracket but do not at this stage tighten these bolts e Remove the rubber O ring from the sensor body and fit into the rebate of the sensor bracket e Push the sensor into the bracket Lock in place using the Components
11. ww competitionsystems co uk Installation TCS4C_ ZX10 2010 AB revision 01 21 01 12 Author Mick Boasman Wiring Rear section Ignition coils 7 pr E I Se k EE 2 1 5 Route this loom section along the RIGHT side of the bike following the standard wiring route and starting from the rear compartment where the TCS module will be located The following 4 connections are all ignition coil INPUT signals from the bike to the TCS unit and must be routed on the A Connect to Coil 1 wiring from bike wiring loom B Connect to Coil 2 wiring from bike wiring loom C Connect to Coil 3 wiring from bike wiring loom D Connect to Coil 4 wiring from bike wiring loom The following 4 connections are all ignition coil OUTPUT signals from the TCS to the drive the ignition coils and must be routed on the E Connect to Coil 1 on the bike F Connect to Coil 2 on the bike G Connect to Coil 3 on the bike H Connect to Coil 4 on the bike IMPORTANT It is vitally important that the coil inputs and outputs are connected correctly or the bike may not start on all cylinders or may even damage the engine Wiring Rear speed Locate the grey 10 way multi block connector at the rear left of the throttle body Now locate the blue wire with yellow stripe as seen in this picture and link it to wire K of the TCS loom using the remaining red quick link In this way the rear speed signal is shared between the TCS
Download Pdf Manuals
Related Search