User's manual
Contents
1. BIBO BRIGHTER WATER Energy saving Sleep mode To save energy your BIBO Bar will go to sleep into a low power state after 4 hours of non use When sleeping the cold water temperature will gradually rise to 10 C and the hot water temperature will gradually drop to 75 C Simply touch any key to wake it up again The hot and cold water will reach their optimum temperatures again after approximately 3 minutes BIBO Bar information amp maintenance Replacing the MAXI filter cartridge To ensure the water from your BIBO Bar continues to taste good the MAXI filter cartridge should be replaced every 6 months How to replace the MAXI filter cartridge Remove the lid from the top of the BIBO Bar by lifting it from the back first You will see the white top of the filter cartridge on the right hand side near to the front It has a handle protruding from the top Turn the handle firmly anti clockwise then pull the cartridge upwards and out Remove the new MAXI filter cartridge from its packaging and insert it Turn it firmly clockwise to install it USER S MANUAL Technical information SPECIFICATION PARAMETER Electrical specification Voltage 230 Volts Frequency 50 Hertz Power rating 000 Watts Current rating 5 8 Amps Heating system Hot tank volume 1 8 Litres Power rating 900 Watts Hot water capacity 10 Litres hour Hot water temperature Maximum 97 C Chilling system Cold tank volume 8 Litres P2. 2 Turn off the water supply to the BIBO Bar by twisting the blue tap at the back of the BIBO Bar so that the lever is at right angles to the white water pipe When you come back Turn on the water supply to your BIBO Bar by twisting the blue tap so the lever is in line with the water pipe 2 Flick the cold and hot tank switches at the back your BIBO Bar to ON 1 3 It s a good idea to rinse fresh water through both tanks so remove the drip tray amp place a jug or similar of at least 2Itrs capacity under the tap then follow steps 4 and 5 below 4 Touch and hold the cold water key for 3 seconds the indicator light on the front of the BIBO Bar will turn blue and the cold water will be automatically dispensed for minute tr approx or you can touch any key to stop the flow 5 Touch the unlock hot key the indicator light on the front of the BIBO Bar turns red immediately touch and hold the cold water key for 3 seconds then hot water will be automatically dispensed for minute I tr approx or you can touch any key to stop the flow 6 The hot tank will now take approximately 5 minutes to reach maximum temperature Disconnecting your BIBO when moving home Turn off the water supply to your BIBO Bar where it is connected to your mains water pipe Normally this connection consists of a white plastic T connector with an integral shut off valve Turn the water off by twisting the grey lever through 90 degrees
3. 14 5psi and 6bar 87psi e Remove the blue locking clip from the inlet water fitting e Depress the collar then remove the blue blanking plug Picture 1 e Insert the water pipe Picture 2 e Replace the blue locking clip Picture 3 A A Y Picture Picture 2 Picture 3 Troubleshooting If a fault should occur please first use the troubleshooting guide below to determine the fault type and then follow the steps listed to resolve the issue This should help you resolve the fault with the minimum effort If you find that your BIBO Bar is not working properly or if the problem persists your BIBO Bar may need to be professionally repaired Please contact us at help bibowater co uk or call 0800 678 5969 to speak to one of our team Your warranty If problems occur with the BIBO please contact BIBO directly via email on help bibowater co uk or call us on 0800 678 5969 Do not attempt to disassemble the BIBO by yourself doing so will invalidate the product warranty and BIBO takes no responsibility for any resulting issues If the BIBO develops any technical problems within the one year warranty period we will repair your BIBO for free You can extend the warranty beyond the first year by visiting our website at www bibowater co uk Appropriate maintenance costs will be charged for any damage that is caused by the misuse of the machine or that is incurred once the warranty period has ended BIBO BRIGHTER WATER Appendices
4. carefully read the self installation instructions on page 2 of this manual Before using the BIBO Bar for the first time Before plugging in and switching on the BIBO Bar ensure the hot tank switch see page 4 of this manual is in the OFF 0 position Failure to do this before the hot tank is full and water is flowing from the water outlet may cause the hot tank thermal overload switch to trip Also ensure the cold tank switch is in the OFF 0 position Hot Water System Switch on the power supply and turn on the water supply to the BIBO Bar The hot and cold water tanks will begin filling automatically As soon as the hot water tank is full you will be able to dispense water by touching the unlock key then the mix water key C can now turn on the hot water tank using the hot tank on off switch on the back of the BIBO Bar The hot water indicator on the control panel lights up When the maximum hot water temperature is reached the indicator goes out Cold Water System As soon as the cold water tank is full you will be able to dispense water by touching the cold water key Ou can now turn on cold water tank using the cold tank on off switch on the back of the BIBO Bar USER S MANUAL Main features Dispensing hot water 97 C To dispense one cup 200ml of hot water Touch the unlock key the indicator light on the front of the BIBO Bar turns red immediately touch the mix water key to dispense 200ml of hot water If you r
5. If the connection is by way of a traditional washing machine type valve twist the blue lever through 90 degrees 2 Back at your BIBO Bar touch the to relieve any pressure in the pipe A small volume of water may be dispensed Touch the key again 3 Flick the cold and hot tank switches at the back of your BIBO Bar to OFF 0 4 At the water connection on the back of your BIBO Bar twist the blue tap lever so it s at right angles to the water pipe Where the pipe enters the tap depress the collar and remove the pipe 5 This length of water pipe should NOT be used again but can be removed from behind under your kitchen units and disconnected from the T connector or washing machine valve 6 If required a black blanking plug is available to fill the small hole in your worktop 7 To re install your BIBO Bar in your new home please follow the relevant sections of the self installation instructions in the Appendices of this manual Safety tips e As your BIBO Bar is full of water it now weighs 7kgs so take care when lifting it e It s important that your BIBO Bar is kept upright during transportation USER S MANUAL www bibowater co uk Call us free on 0800 678 5969
6. Self installation instructions Please note these instructions should be used in conjunction with this users manual and the BIBO Bar self installation kit which should have been delivered with your BIBO Bar These instructions should be followed by a plumber kitchen fitter builder water cooler installer or similarly experienced person If at all unsure please call us on 0800 678 5969 and ask to speak to one of our installation team Water Supply Connection If you have a water softener fitted in your home the water connection for the BIBO should ideally be made before the softener i e to an un softened water supply In case you need to turn off the mains water supply to your home identify where the tap isolation valve is located before beginning the installation Preparation As well as your BIBO Bar the box contains a self installation kit consisting of a length of water pipe a BIBO T connector a shut off valve a pressure relief valve and a right angle fitting There is included an additional length of pipe with a straight connector if needed 2 When you ve decided where to locate your BIBO identify a suitable mains cold water supply nearby More often than not this will be under your kitchen sink or behind your dishwasher or washing machine Ideally this should be a 5mm copper pipe in good condition with enough of the pipe exposed to enable you insert the BIBO T connector 3 Often there is a valve to enable you to
7. User s manual Congratulations Congratulations and thank you for buying a and chilled at the touch of a button We want you to get the most from your B BIBO Bar You are moments away from enjoying pure filtered water boiling BO so before you use it please read this manual carefully If you have any queries once your BIBO Bar is up and running please first refer to this manual it will provide you with helpful and practical advice There s also a v www bibowater co uk deo on our website to guide you through using the BIBO Bar Please feel free to contact us if you have an y further queries or to give any feedback on your BIBO Bar or our service Whatever you need our Support team is just an email or a phone call away Visit www bibowater co uk contact email help bibowater co uk or call 0800 678 5969 Please note The pictures and diagrams in this manual are for reference only please refer to your BIBO Bar We reserve the right to make corrections or changes to the information provided in this manual without prior notice being given The products functions structures and desi protected by the UK amp EU patent offices gns described in this manual have been patented by our company and are thus Copyright BIBO 2013 All Rights Reserved USER S MANUAL Contents Meet your BIBO Bar BIBO Bar overview e The control panel Using your BIBO Bar e Important before using your BIBO Bar
8. ar in tts preferred location on the work surface Remove the plastic bag and protective covering from the cable and plug Remove the drip tray wrapping gt A wW N Remove the blue locking clip from the inlet water fitting on the back of your BIBO Bar depress the collar on the fitting then remove the blanking plug see the pictures on page 10 of this manual for guidance 5 Push the right angle water fitting supplied with the BIBO self installation kit into the water inlet then replace the blue locking clip 6 Push the short length of pipe from the shut off valve into the right angle fitting Setting Up Safety tip Make sure both power switches on the back of your BIBO Bar are in the off o position before connecting to the power supply see the illustration on page 4 of this manual for guidance Now follow the instructions called Using Your BIBO Bar on pages 6 8 of this manual PLEASE ENSURE THAT YOU DO NOT TURN THE BIBO BAR S HOT TANK SWITCH ON THIS IS ON THE BACK OF UNIT CLEARLY LABELLED UNTIL YOUR BIBO HAS FILLED ITSELF WITH WATER If you have any questions please call us 0800 678 5969 BIBO BRIGHTER WATER Preparing your BIBO Bar for when you are going on holiday If at all unsure how to proceed please call us on 0800 678 5969 and ask to speak to one of our installation team Before you go Flick the cold and hot tank switches located at the back of the BIBO Bar to off o
9. equire less water touch any key to stop the flow To dispense a larger quantity of hot water Touch the unlock key the indicator light on the front of the BIBO Bar turns red immediately touch and hold the cold water key for 3 seconds then hot water will be automatically dispensed for minute I ltr approx or you can touch any key to stop the flow Dispensing extra hot water 97 C Touch and hold the extra hot key for 3 seconds the indicator light on the front of the BIBO Bar will turn red the extra hot water indicator will illuminate and the hot tank will heat to 97 C When the maximum temperature is reached the indicator light will go off Now follow the instructions above Dispensing cold water 5 C To dispense one cup 200ml of cold water Touch the cold water key the indicator light on the front of the BIBO Bar will turn blue and it will dispense 200ml of cold water If you require less water touch any key to stop the flow To dispense a larger quantity of cold water Touch and hold the cold water key for 3 seconds the indicator light on the front of the BIBO Bar will turn blue and the cold water will be automatically dispensed for minute Iltr approx or you can touch any key to stop the flow Dispensing ambient water 25 C Touch the MIX water key the indicator light on the front of the BIBO Bar will turn purple the BIBO will dispense 200ml of ambient water If you require less water touch any key to stop the flow
10. for the first time e Main features e Energy saving BIBO Bar information amp maintenance e How to replace the filter e Technical information e Cleaning your BIBO Bar e Safety notes Installing your BIBO Bar e Overview e Water supply connection e Troubleshooting e Your warranty Appendices e Self installation instructions e Going on holiday e Moving house pages 4 5 pages 6 7 8 pages 8 9 10 pages 10 11 pages 12 13 14 Please note that the pictures and diagrams in this manual are for reference only refer to your BIBO Bar We reserve the right to make corrections or changes to the information provided in this manual without prior notice being given Manual version 30092013 Copyright BIBO 2013 All Rights Reserved BIBO BRIGHTER WATER Meet your BIBO Bar BIBO Bar overview Control panel 9 Cold tank switch 2 Indicator light 0 Hot tank switch 3 Water outlet Service cover 4 Front panel 2 Cooling vent 5 Removable drip tray cover 3 Water inlet 6 Side panel 4 Overflow outlet 7 Removable drip tray 5 Mains power cable 8 Lid 6 Mains fuse USER S MANUAL The control panel Unlock Hot g Extra hot Cold water ae Hot water 7 Mix water key Cold water key ee i Filling indicator as water key water indicator indicator indicator BIBO BRIGHTER WATER Using your BIBO Bar If you are installing your BIBO Bar yourself please
11. isolate the chosen pipe If not then it will be necessary to turn off the main water supply to your home Be sure to drain as much water as possible from the pipe before cutting it Using a suitable pipe cutter make two cuts in the pipe removing a 20mm section Push the two exposed ends of the copper pipe firmly into each end of the BIBO T connector Ma ke sure the tap on the BIBO T connector is turned off i e parallel to the copper pipe A Or Ou ak Turn the water supply back on and make sure there are no leaks where the copper pipe fits into the BIBO T connector Push the 6mm white water supply pipe provided with your BIBO firmly into the fitting on the T piece 9 Run this pipe behind or underneath your kitchen base cabinets then bring it up through the worktop behind your BIBO Bar Cc 10 Push the end of the pipe into the blue amp white shut off valve supplied with the BIBO T connector USER S MANUAL Installation Safety tips e Remember your BIBO Bar weighs 4kgs so take care when lifting it from its box e Install your BIBO Bar in a cool dry place where it is well ventilated It must be kept away from any heat source e Keep the rear of your BIBO Bar at least 5cm 2 away from the wall e The water pressure should be between Ibar 14 5psi and 6bar 87psi e Your BIBO Bar needs a normal 3amp power supply Carefully remove the packaging and place your BIBO B
12. ower rating 120 Watts Cooling current 0 8 Amps Cold water capacity 3 Litres hour Cold water temperature Minimum 5 C Filtration system Activated carbon filter 0 5 Micron Inlet water pressure Minimum Maximum bar 14 5psi 6 bar 87psi Dimensions mm 375H X 350 D X 320 W Weight 14 Kgs Operating standards GB4706 1 2005 GB4706 3 2008 GB4706 19 2008 GB T22090 2008 The maximum ambient working temperature is 38 C The dispense capacity is calculated at an ambient and inlet water temperature of 25 C BIBO BRIGHTER WATER Cleaning your BIBO Clean your BIBO Bar by simply wiping it down with a damp cloth Soap or any other gentle detergent can also be used if you wish The drip tray can be removed and cleaned in your dishwasher Please don t use harsh detergents concentrated washing up liquid or solvents to clean your BIBO Avoid using anything abrasive such as steel brushes scourers etc to clean the body as it will scratch It s very important that you don t wet the back of the machine whilst cleaning remember it is connected to an electrical supply Safety notes e This BIBO Bar is for indoor use only Avoid placing it in direct sunlight or next to flammable materials Avoid placing the BIBO Bar near other appliances that could get damaged if wet Do not immerse the BIBO Bar in water The BIBO Bar uses 230VAC voltage and should be used with a 13 amp fuse in the plug top Impor
13. tant when using a new or freshly cleaned BIBO for the first time it s important that water is flowing when both the hot and cold water keys are touched before you switch on the hot water tank The BIBO Bar dispenses safe and great tasting drinking water The tanks are not pressurized and the hot tank is directly connected to the hot water outlet No valves are used so it is normal therefore for a small amount of excess water to be released once water has been dispensed The BIBO Bar can produce high temperature hot water As with any kettle pan or appliance capable of producing hot water please use caution when dispensing hot water When your BIBO Bar is turned on for the first time or after a period of not being used please run at least 2 litres of water through both the hot and cold outlets before drinking any to ensure the water is fresh e Warning The BIBO Bar must be used with a reliable earth in the mains power supply socket For further notes or detailed explanations on the operation of the machine please contact BIBO via email at help bibowater co uk Installation Overview e Install the BIBO Bar in a cool dry place where it is well ventilated It must be kept away from any heat source e Keep the rear of the BIBO Bar a minimum of 5cm 2 away from the wall and ensure that the part of the dispenser is well ventilated USER S MANUAL Water supply connection e The water pressure should be between bar
Download Pdf Manuals
Related Search