Home

HOP-1001/1002 SIP Phone User Manual

1. Hand free Press Speaker to speak to the other party When the call is over press Speaker again Hand free to handset While receiving the call with Speaker pressed pick up the handset to continue the call When the call is over put back the handset Note When you communicate with the other party without lifting the handset please do not exceed 40 CM from speaker gt Place a call e Call another HOP 1001 1002 IP phone under the same SIP Proxy 1 Handset Pick up the handset and listen for the Internet dial tone Then dial the phone number you wish to call and press to end the dialing Once the call connection has been established and the ring tone has sounded wait for the other party to answer When the other party answers you can begin speaking When the call is over put back the handset The dialed number has been saved into the buffer 2 Hand free Press Speaker and listen for the Internet dial tone Then input the phone number you wish to call and press to end the dialing Once the call connection has been established and the ring tone has sounded wait for the other party to answer When the other party answers you can begin speaking When the call is over Press 40 HOP1001 1002 SIP Phone User Manual Speaker again The dialed number has been saved into the buffer 3 Blind dialing Use the keypad to enter the phone number you wish to call and then press to ma
2. gt Note Usually the echo time of ping command is no more than 1 second So if the result is not displayed in 5 seconds ping command is fail ftp command Syntax description ftp value Usage the system connects to the FTP server auto to get the corresponding file and deal with it Relevant usage ftp X X ranged from 0 through 2 X 0 Connect to FTP Server to get the file of updating program and save it to the SDRAM of the phone Then the file can be read by PalmTool This operation aims at testing X 1 Connect to FTP Server to get the file of updating program and update program Flash This operation aims at updating program X 2 Connect to FTP Server to get the file of updating dial rules and update program Flash This operation aims at updating dial rule Note When you use ftp 0 and ftp 1 commands if the file get from FTP server is too large or the net speed is too slow then the process will not be seen in telnet window Please be patient Using ftp command in telnet to get file spends almost same minutes as getting file using phone So if nothing is displayed after too long time it means that ftp is fail Note All the Telnet commands of HOP 1001 1002 IP phone should be written in low case and the password is case sensitive gt Upgrade HOP 1001 1002 IP phone gt Prepare Updated program 38 HOP1001 1002 SIP Phone User Manual gt Upgrade HOP 1001 1002 IP phone by palmtools 1 Open the IE browser 2 Inp
3. Vol backward cursor backward Exit current menu exit setting mode Keypads Modify values Redial Refer to above operation you can reach any menu to modify any value Please refer to following structure illustrations to learn the values of each menu item As for the meaning of each item and value please refer to Web Browser Setting chapter e Menu Structure HOP1001 1002 SIP Phone User Manual HOP1001 1002 SIP Phone User Manual HOP1001 1002 SIP Phone User Manual gt Configured by WEB Double click E icon to open the IE browser Input the IP address of the phone into address bar Address 192 168 1 100 and then input password of the phone into the following page Default password 1234 is ordinary password and super password is 19800211 12345678 or 19750407 With Debug set O disable please input super password while Debug is not set as O disable please input ordinary password Then clickL_1zix button The following configured page wills popup Refer HOP1001 1002 SIP Phone User Manual to Fig 3 1 please network settings iptype dhcp v ppp id PPP pin local ip 192 168 1 212 subnet mask 255 255 255 0 router ip 192 168 1 254 dns 202 106 46 151 dns2 202 96 128 68 mac protocol settings 15390 service addr 203 93 9 57 service id 00 09 45 60 16 63 use service iV common x register ttl jitter size service type nat traversal
4. citron gt nat addr Po nat ttl fo phone number 106T account Sf ss S pin SC ti lt CS SC register port T20 signal port T20 control port i722 dtmf control string v dtmf payload fio rtp port i722 local type account call type advanced rtp tos fo phone settings use dialplan enable dial number I dddcode fic iddcode je iddprefix foo dddprefix fo innerline enable local prefix po nonlocal prefix fo ring type fatmf0 use digitmap O call waiting T forward number e2370 fwd poweroff O fwd noanswer Vv fwd always O fwd busy O answer po audio settings vad K age T aec Vv codec e7231 gt codec2 e729 codec3 feTliu gt codect esn z codecS u gt g 723 1 high rate Vv audio frames 2 handset in mooo handset out po speaker out jpo other settings password i234 super password 12345678 debug disable gt sntp ip 210 59 157 10 use daylight O upgrade adr O timezone GMT 08 00 Beijing Hong Kong Urumqi E Save Settings Address Book Upgrade Firmware Fig 3 1 Http Setting Network Setting network settings iptype static ppid ftestl ppp pin festi local ip 192 168 1 100 subnet mask 255 255 255 0 router ip 192 168 1 254 dns 202 106 196 115 dns2 202 96 128 68 mac Fig 3 2 Network Setting 00 09 45 63 17 a8 e iptype Set how IP phone gets relevant network parameters by selecting corresponding item from drop down list Static ip Select this item to authorize users set IP address
5. set upgradeaddr XXX XXX XXX XXX Set IP address or domain name of FTP server supplying upgraded program of HOP 1001 1002 IP phone set ntsip XXX XXX XXX XXX Set IP address of time server set daylight X Set use daylight or not X ranged from O through 1 0 do not use daylight 1 use daylight set timezone XX Set time zone 36 HOP1001 1002 SIP Phone User Manual Command store Syntax description no keyword Parameter ranged from 0 through 4 Usage Save the current settings to the designated position Relevant Usage store 1 Command load Syntax description no keyword Parameter ranged from 0 through 4 Usage Load the designated settings to the current position Relevant Usage load 1 Command exit Syntax description no keyword and parameter Usage Exit from Telnet command window without saving the configuration Relevant usage None Command write Syntax description No keyword and parameter Usage Save the configuration and restart the HOP 1001 1002 IP phone Command ping Syntax description ping IP address Usage ping IP address of other NAT device Relevant usage In telnet window input ping xx xxx xx xx Can IP address and return then the result will be displayed If the address is effective ping OK will be seen if the address is ineffective nothing will be seen Fox example 37 HOP1001 1002 SIP Phone User Manual P gt ping 203 93 9 57 P gt ping OK P gt ping 27 56 120 56 P
6. subnet 10 HOP1001 1002 SIP Phone User Manual mask and router IP address of IP phone manually dhcp Select this item to enable DHCP mode With this system your LAN or router automatically assigns all the required network parameters to any device connected to it when the device log on HOP 1001 1002 IP phone is shipped from the factory with DHCP on So if your LAN or router is configured to use DHCP addressing the IP phone s LAN parameters will automatically be configured as soon as it is connected to the LAN or router and powered up pppoe Those ADSL and Cable Modem users please select this item for it is a protocol especially designed for them With this system ADSL ISP automatically assigns all the required IP parameters to any device connected to it when the device log on modem If the IP phone used with modem please select this item to get relevant network parameters auto Then please fill ID and pin into ppp id and ppppin fields ppp id With pppoe or modem selected in iptype drop down list please enter the user name here ppp pin With pppoe or modem selected in iptype drop down list please enter the password here HOP1001 1002 SIP Phone User Manual e local ip With static ip selected in iptype drop down list please enter IP address of IP phone here e subnet mask With static ip selected in iptype drop down list please enter subnet mask of IP phone here e router ip With static ip selected in
7. 00 Beijing Hong Kong Urumqi bs Save Reboot Address Book Upgrade Firmware Fig 3 7 Setting Page using ordinary pin with Debug set as 0 disable e Update Click this button to save the configuration and the phone will reboot Once the phone reboots successfully the new configuration is effective Note After entering set page if Update button is not clicked within 5 seconds then when you click it again the index page asking for pin will pop up again Then please input the password again to enter the set page and then click Update button to confirm the modification Phone Book Click this button to open the speed dial settings page Please refer to Fig 3 7 In this page you can set and save the speed dial number by typing the name into the Name field and then entering the corresponding number following the name For example input Jack in Name field following 001 and then input 5989426454 into Phone number field Then Jack s number 5989426454 is saved in phone book Then please click Save Back button In normal state you can use speed dial to call numbers saved in phone book 21 HOP1001 1002 SIP Phone User Manual Phone Book Ho Hame Phone Humber Ho Hame Phone Humber 001 Tack 5989426454 002 fallen 192 168 1 56 ca jyt A O M yy f CEE M O a jijf orf jit Oe tf cua M A o M jj E Fig 3 8 Phone Book Illustration Upgrade Program Click this button to update the program of IP phone Before updating pleas
8. 52 HOP1001 1002 SIP Phone User Manual gt HOP 1001 1002 IP phone Appearance Introduction e HOP 1001 1002 IP Phone Front Illustration Refer to Fig 1 1 Ready For Calls WuChuan V 1 20 Fig 1 1 H P 1001 1002 IP Phone Front Illustration e HOP 1001 1002 IP Phone Back and Side Illustrations Refer to Fig 1 2 and 1 3 Fig 1 2 HOP 1001 1002 IP Phone Back Handset cord Jack Illustration Fig1 3 HOP 1001 1002 IP phone Side Illustration gt Function Keys of HOP 1001 1002 IP Phone Introduction Normal State 1 LCD 2 Quick Dial 3 backspace 4 Volume Key 5 Volume 6 Volume 7 Number 8 Mis Calls 9 Dial Calls 10 Rec Calls 11 Hold 12 Flash 13 Redial 14 Local IP 15 Speaker 16 Num Key 17 Handset 18 LED HOP1001 1002 SIP Phone User Manual Keys Function Mis Calls With handset hung press this key to review missed number Rec Calls With handset hung press this key to review received number Phone With handset hung press this key to get phone number number Dial Calls With handset hung press this key to review dialed number Redial Press this key to redial current number Press this key to have a call without lifting the handset Speaker Press Volume then press Increase the volumes of handset or speaker Volume Press Volume then press Increase the volumes of handset or speaker Volume Volume Press Volume then press Increase the volumes of handset or speaker Keypad W
9. dialplan drop down list you can also set dddcode iddcode iddprefix and dddprefix according to requirement of system e innerline Enable disable multi settings by selecting corresponding items from dropdown list HOP 1001 1002 IP phone allows saving 5 settings totally a disable Disable multi settings by selecting this item then the phone will call out using current setting enable Use designated system to place calls by selecting this item e local prefix With enable selected in innerline dropdown list please fill the number switching to local call such as 0 e nonlocal prefix With enable selected in innerline dropdown list please fill the number switching to long distance call such as 9 e ring type Set ring type by selecting corresponding item from drop down list dtmf 0 9 Set ring as ordinary rings in different frequency not disturb Set the phone do not ring by selecting this item pcmring Set ring as music shipped from factory by selecting this item user define Set ring as music saved by user by selecting this item e Use digitmap Enable disable digit map by checking unchecking the box e Call waiting Enable disable call waiting by checking unchecking the box HOP1001 1002 SIP Phone User Manual e forward number Enter receiving forwarded calls phone number into this field If the IP phone used with modem with modem item selected in iptype list box and then fill ISP number into this
10. package in RTP digital follow set rtpport XXXX RTP port is the port transferring and receiving voice flow using UDP protocol XXXX is range from 1024 through 65535 set jittersize X 30 HOP1001 1002 SIP Phone User Manual Set buffer size of RTP package X is range from 0 32 set calltype X Set call type of the phone X is ranged from 0 through 1 0 when SIP system not support outbound proxy 1 when SIP system not support outbound proxy set dtmf X Set DTMF relay type X is ranged form O through 3 O control string 1 inband audio 3 rfc 2833 set dtmf payload X When dtmf X select 3 rfc 2833 This parameter can be used indicating type of RTP payload type The value can be use integer 96 101 set dialplan X Enable disable dial plan and dial number Parameter X ranged from O through 3 0 disable dial plan 1 enable dial plan 2 use dial number 3 use special prefix service 4 use hotline function set dialnumber XX When set dialplan value set as 2 please use this command to set dial number When set dialplan value set as 4 please use this command to set hotline number set dddcode XX Set the area code when set dialplan value set as 1 or 2 For 31 HOP1001 1002 SIP Phone User Manual example the area code of Beijing is 10 the area code of Shanghai is 21 and the area code of Chengdu is 28 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters set iddcode XXX Set the country code
11. please press to place a call directly Note HOP 1001 1002 IP phone supports saving 80 entries unanswered call dialed call and received call ranged from 1 80 at best When the entries arrives 80 the latest record will cover the first one The record will be lost when the phone restarts or turned on gt Boot up error It is acommon problem maybe caused by upgraded a wrong binary file into the ip phone 1 Get the correct binary file for your hardware type 2 Press and hold key power on it for 2 times each time make sure you see display on the LCD IP address of IP phone become 192 168 1 100 default ip address 3 Make your pc ip address like 192 168 1 101 4 Run palmtool exe 5 Input 192 168 1 100 into IP Address in Chip field Select the correct upgrade file and use palmtool Update Program button to upgrade IP phone If IP Phone still does not boot Please Press and hold key power on it for 2 times and press 5 5 key sequence to restore default settings Appendix Table HOP 1001 1002 IP phone digital character key map Keys Press Once Press Twice Press Thrice Press quartic Press quintic 42 HOP1001 1002 SIP Phone User Manual 1 1 ci I 2 2 Ala B b Cie 3 3 D d E e F f 4 4 Gig H h li g 5 5 Jij K k L I 6 6 M m N n O o 7 7 P p Q q R r S s 8 8 T t U u Viv 9 9 W w X x Y y Ziz 0 0 space am
12. system which requires authentication please put the password into this field HOP1001 1002 SIP Phone User Manual e register port The local UDP port registered with server to accept incoming handshaking messages The default port number is 5060 e dtmf Set DTMF signal sending way by selecting control string inband audio signal keypad or rfc 2833 from list box e dtmf payload When DTMF select rfc 2833 This parameter can be used indicating type of RTP payload type The value can be use integer 96 101 e rtp port RTP port is the port transferring and receiving voice packets using UDP protocol This is an even number between 1024 and 65535 can t be the same as register port e call type Set call type by selecting the items in drop down list normal When SIP system not support outbound proxy selecting this item e advanced When SIP system support outbound proxy selecting this item default setting is this item e rtp tos Set the TOS field of the IP header of the RTP packets The bigger this value is 0 the higher priority the packet is phone settings phone settings use dialplan enable dial number pooo dddcode iddcode sa iddprefix joo dddprefix innerline enable local prefix pooo ring type dtn gt use digitmap L forward nunber 82378009 fwd poweroff O r fwd always E fwd busy nonlocal prefix call waiting fwd noanswer TTT answer Fig 3 4 Phone Setting e use d
13. to use digitmap X ranged from 0 to 1 0 do not use digitmap 1 use digitmap set fwdnumber XXXXXXX Set receiving forwarded calls phone number XXXX must be an Arabic numeral and no longer than 16 characters set fwdpoweroff X Enable disable forward calls if power off X is ranged from O through 1 0 do not forward calls if power off 1 forward call if power off set fwdalways X 33 HOP1001 1002 SIP Phone User Manual Enable disable forward all calls X is ranged from O through 1 0 do not forward all calls 1 forward all calls set fwdbusy X Enable disable forward calls if busy X is ranged from 0 through 1 0 do not forward calls if busy 1 forward call if busy set fwdnoanswer X Enable disable forward calls without replying X is ranged from 0 through 1 0 do not forward calls without replying 1 forward call without replying set audioframes X Set audio frames in RTP package X is Arabic numerals between 0 and 7 set 6 3k X With G 7231 set HOP 1001 1002 IP phone to use 6 3K rate or not X is ranged from 0 through 1 0 use 6 3K rate 1 use 5 3K rate set vad X Enable disable VAD X is ranged from 0 through 1 0 disable VAD 1 enable VAD set agc X Enable disable AGC X is ranged from 0 through 1 0 disable AGC 1 enable AGC set aec X 34 HOP1001 1002 SIP Phone User Manual Enable disable AEC X is ranged from 0 through 1 0 disable AEC 1 disable AEC set handsetin X Set initial volume of handset
14. when set dialplan value set as 1 or 2 For example the country code of China is 86 the country code of USA is 1 etc Parameter xxxx must be an Arabic numeral and no longer than 4 characters set iddprefix XX Set IDD service prefix number when set dialplan value set as 1 or 2 For example IDD service prefix number of china is 00 IDD service prefix number of USA is 1 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters set dddprefix XX Set DDD service prefix number when set dialplan value set as 1 or 2 For example DDD service prefix number of china is 0 DDD service prefix number of USA is 1 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters set innerline X Set use innerline call or not X ranged from 0 through 1 0 disable 1 enable innerline call set localpreifx X 32 HOP1001 1002 SIP Phone User Manual With innerline set as 1 enable please set the number switching to local call such as 9 set nonlocalprefix X With innerline set as 1 enable please set the number switching to long distance call such as 9 set answer X Set the ring seconds before the phone answers the call auto or forward the calls X is ranged from 0 through 60 set ringtype X Set types of ring X is ranged from 0 tohrough 12 0 9 ring as ordinary rings in different frequency 10 do not ring 11 ring as music shipped from factory 12 ring as music saved by user set digitmap X Set whether
15. HOP 1001 1002 SIP Phone User Manual HOP 1001 1002 SIP Phone User Manual HOP 1001 1002 IP phone Appearance Introduction 2 Function Keys of HOP 1001 1002 IP Phone Introduction 2 FeatureS 2 Operating requirements 6 Electric requirements 6 SiZe 6 Configuration 6 Phone Keypad setup 6 Configured by WEB 11 Configured by PalmTool 29 Telnet Configuration 29 Upgrade HOP 1001 1002 IP phone 48 Usage of the phone 49 Boot UP erfOf 52 Appendix Table
16. Internet s remote login protocol e FTP File Transfer protocol e HTTP Hyper Text Transfer protocol gt Operating requirements e Operation temperature 0 to 50 C 32 to 122 F e Storage temperature 30 to 65 C 22 to 149 F e Humidity 10 to 90 no dew HOP1001 1002 SIP Phone User Manual gt Electric requirements e Voltage 9V DC e Power 9W max e Power adapter AC DC input 100 230V output 9V 1A e Network interface 1 2 X RJ 45 Ethernet Connectors gt Size 215 x 190 x 70 mm Lx W x H gt Configuration Four different ways can be used to configure HOP 1001 1002 IP phone phone keypad web browser Telnet commands and PalmTool configuration tool on computer gt Phone Keypad setup e Use keypad setup Press and hold key while power up until you see Password begin to display on your LCD 1 Enter password of the phone Default password 1234 is ordinary password and super password is 19800211 12345678 or 19750407 With Debug set O disable please input super password while Debug is not set as O disable please input ordinary password 2 Press Speaker key e Function Keys Introduction When using keypad and LCD to configure the settings of IP phone following keys will be used HOP1001 1002 SIP Phone User Manual Keys Function Keys Function Local IP Enter setting mode Speaker Enter submenu confirm change Turn over menu Turn over menu forward move Vol
17. X is ranged from 0 through 15 set speakerin X Set initial volume of microphone of the base X is ranged from 0 through 15 set handsetout X Set initial volume of handout X is ranged from 0 through 31 set codec1 X Set the priority 1of the audio compression algorithm X is range from O through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec2 X Set the priority 2 of the audio compression algorithm X is range from O through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec3 X Set the priority 3 of the audio compression algorithm X is range from O through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec4 X Set the priority 4of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec5 X 35 HOP1001 1002 SIP Phone User Manual Set the priority 5 of the audio compression algorithm X is range from O through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set password XXXX Set password of the HOP 1001 1002 IP phone XXX must be ASCII characters set superpassword XXXX Set super password of the HOP 1001 1002 IP phone XXX must be ASCII characters set debug X Set open debugging message output grade for special tool X is ranged from 0 through 5 0 close debugging output 1 output the operation information to the window 2 output all the bug information and data in test window 3 save the bug information into SDRAM 4 disable checks the mark
18. ant commands Relevant usage None Detailed description List help of all commands For example P gt set get list settings store x store current to xth settings load x load xth settings to current exit write save settings Command get Syntax description No optional parameter of keywords Usage Display basic parameters of the HOP 1001 1002 IP phone Relevant usage None Detailed description get Display basic running parameters of the HOP 1001 1002 IP 24 HOP1001 1002 SIP Phone User Manual phone Input ordinary password without debug being set as O disable or input super password with debug set as Ofdisable then following parameters of IP phone will be displayed HOP 1001 1002 V1 39 settings Password P gt get iptype O static ip 192 168 1 100 subnetmask 255 255 255 0 router 192 168 1 254 dns 202 106 196 152 dns2 202 106 196 115 mac 00 09 45 65 a3 e6 service 1 enable servicetype O common _ serviceaddr 203 93 9 57 serviceid empty nattraversal 1 enable nataddr www showmyip com natttl 30 phonenumber 182378009 account empty pin empty registerport 6800 signalport 6800 controlport 6802 registerittl 60 rtptos 0 rtpport 6802 jitter size 0 calltype 1 advanced localtype O phonenumber dtmf O control string dtmfpayload 101 dialplan 2 dialnum dialnumber 17911 dddcode empty iddcode empty iddprefix empty dddprefix empty innerline 1 enable localprefix 0 nonlocalprefix 0 answer 5 r
19. e Start gt Run and then type telnet 192 168 1 100 into Run field in popuping Run dialog Or input telnet 192 168 1 100 in the DOS window Then the following information will be displayed HOP 1001 1002 V1 39 settings Password Then please type password With debug is set as O disable if type ordinary password default one is 1234 after Retun you will see Password P gt If you type super password then you will see Password a RRERKRERE P gt Above information indicates that IP phone is under setting mode and then you can set the HOP 1001 1002 IP phone by using the telnet commands gt HOP 1001 1002 Telnet Commands Explanation HOP 1001 1002 Telnet Commands Command Function Supply command name and parameters get Display basic parameters of the HOP 1001 1002 IP phone set Set parameters of the HOP 1001 1002 IP phone store Save current settings to designated position load Load designated settings to current position exit Exit from the setting mode without saving the configuration write Exit with saving all configurations and restart HOP 1001 1002 ping Ping other net parameter ftp The phone connects to FTP server and then get the files 23 HOP1001 1002 SIP Phone User Manual Detail description of HOP 1001 1002 Telnet commands Command Syntax description No optional parameter Usage Type command name and parameters following P gt Be used as the keyword to supply keyword and parameters of the relev
20. e fill IP address of FTP server into upgrade addr field and then click this button Then the phone will read the corresponding bin files from the server and then load into the phone Update Digitmap Click this button to update the digitmap of the phone Before updating please fill IP address of FTP server into upgrade addr field and then click this button Then the phone will read the corresponding map files from the server and then load into the phone Note Please refer to PalmToo User Guide to learn how to write digitmap or just download TXT file from our site Then please save it as phone type map file such as pa168S map gt Configured by PalmTool PalmTool is a tool designed especially to configure and upgrade the HOP 1001 1002 IP phone You can visit website to download the latest version of PalmTool Then please unzip the downloaded file and save them a On a PC double click Gicon to open the PalmTool The index page of PalmTool will popup b Input the IP address of the phone into Local IP field such as 192 168 1 100 and then click Phone Settings button From Version1 24 use PalmTool to set the IP phone please set debug as output or output all firstly or PalmTool cannot connect IP phone The parameters of PalmTool is same as the parameters in HTTP so please refer to HTTP set chapter to learn how to set IP phone 22 HOP1001 1002 SIP Phone User Manual gt Telnet Configuration e Onthe PC choos
21. field e fwd poweroff Forward calls if power off by checking this box Please enter receiving forwarded calls phone number into fwd number field e fwd noanswer Forward calls without replying by checking this box Please enter receiving forwarded calls phone number into fwd number field e fwd always Forward all calls by checking this box Please enter receiving forwarded calls phone number into fwd number field e fwd busy Forward calls if busy by checking this box Please enter receiving forwarded calls phone number into fwd number field e answer Enter a number from O through 60 to set the entries of the seconds before the phone answer the call auto or forward the calls Audio settings audio settings vad IV age O aec IV codec e7231 gt codec e729 gt codec3 feTl1u gt codecd gsh oY codecS u gt g 723 1 high rate Vv audio frames 2 handset in z handset out po speaker out jpo Fig 3 5 Audio Setting e vad Enable disable VAD voice activity detection e agc Enable disable AGC e aec Enable disable VEC e codeci Set the priority 1of the audio compression algorithm The options are g729 g7231 g711u g711a and gsm 18 HOP1001 1002 SIP Phone User Manual e codec2 Set the priority 2of the audio compression algorithm The options are g729 g7231 g711u g711a and gsm e codec3 Set the priority 30f the audio compression algorithm The options are g729 g7231 g711u g711a and gsm e codec4 Set the p
22. ialplan Set whether use dial plan or use dial number by selecting the corresponding item in drop down list disable Do not use dial plan or dial number by selecting this item HOP1001 1002 SIP Phone User Manual enable Use dial plan by selecting this item dialnum Use dial number by selecting this item With this item selected please enter the dial prefix into dial number field prefix Use specially service by selecting this item Hotline Use Hotline function by selecting this item With this item selected please enter the hotline number into dial number field dial number With dialnum selected in use dialplan drop down list please enter the dial prefix into this field according to requirement of log in server For example with eTalk card used enter 00 here ddd code With enable or dialnum selected in use dialplan drop down list set area code according to E 164 dial rule For example Beiing 10 Shanghai 21 idd code With enable or dialnum selected in use dialplan drop down list set country code according to E 164 dial rule For example China 86 U S A 1 idd prefix With enable or dialnum selected in use dialplan drop down list set international call prefix according to E 164 dial rule such as 00 ddd prefix With enable or dialnum selected in use dialplan drop down list set long distance call prefix according to E 164 dial rule such as 0 HOP1001 1002 SIP Phone User Manual Note With dialnum seletcted in use
23. in system does not support IP phone working behind the LAN With this item selected please make port mapping on NAT device 4 stun set nataddr XXXXX When nattraversal is set to 1 set IP address of NAT device wan port or URI of free assistant service Such as www showmyip com etc in Internet When nattraversal is set to 4 set IP address or URI of the stun server in the format as domain name IP address service port The default service port for stun is 3478 NOTE The free service list of Internet www ip calculator com www ipchicken com www ipchicken com www showmyip com www whatismyip com www myipaddress com www whatismyipaddress com ip sbbs net www whatismyipaddress net checkip dyndns org set natttl XX 29 HOP1001 1002 SIP Phone User Manual Set NAT TTL XX is an integer between 10 and 65535 sec default value is 20 sec set phonenumber XXXXXXXX Set a local ID of HOP 1001 1002 IP phone Value xxxxx must be an Arabic numeral and no longer than 16 characters set account XXXXXX Set the account Value xxxxxx must be an Arabic numeral and no longer than 32 characters set pin XXXXXXXXXX Set the account Value xxxxxx must be an Arabic numeral and no longer than 32 characters set registerport XXXX Set register port Value XXXX default is 5060 set registerttl X Set register TTL X is range from 10 through 65535 Sec default value is 60 Sec set rtptos X Set TOS segment of IP head
24. ingtype O dtmf0 digitmap O disable fwdnumber empty fwdpoweroff 1 enable fwdalways O disable fwdbusy O disable fwdnoanswer O disable audiotype 0 g7231 audioframes 1 6 3k 1 enable vad 1 enable agc O disable aec 1 enable handsetin 9 handsetout 21 speakerout 21 codec1 1 g7231 codec2 0 g729 codec3 2 g711u codec4 4 gsm codec5 5 null password 1234 superpassword 19750407 debug 1 output upgradeaddr empty sntpip 0 0 0 0 daylight O disable timezone 55 GMT 08 00 Beijing Hong Kong Urumqi Input ordinary password with debug set as O disable following information will be seen 25 HOP1001 1002 SIP Phone User Manual HOP 1001 1002 V1 39 settings Password P gt get iptype O static ip 192 168 1 100 subnetmask 255 255 255 0 router 192 168 1 254 dns 202 106 196 152 dns2 202 106 196 115 natiraversal 1 enable nataddr rtpport 5144 registerport 5142 signalport 5142 controlport 5144 account empty pin empty phonenumber 182378009 fwdpoweroff O disable fwdalways O disable fwdbusy O disable fwdnoanswer O disable ringtype O dtmf0 answer 5 password 1234 upgradeaddr empty sntpip 0 0 0 0 daylight O disable timezone 55 GMT 08 00 Beijing Hong Kong Urumqi Command set Syntax description set keywords value Usage Used to configure password and other running parameters of HOP 1001 1002 IP phone Detailed description set iptype X Set how IP phone gets relevant network parameters X ranged fro
25. iptype drop down list please enter router IP address of IP phone here e dns With static ip selected in iptype drop down list please enter IP address of DNS server here e dns 2 With static ip selected in iptype drop down list please enter IP address of backup DNS server here e mac MAC address is the physical address supplied by the Ethernet NIC HOP 1001 1002 phone is shipped from the factory with a unique algorism MAC address printed on the back of the base Protocol Setting protocol settings use service IV register ttl 15390 jitter size fo service type common 7 service addr f203 93 9 57 service id o nat traversal citron nat addr oOo O O nat ttl poo phone number jor o account Po pin Po register port i720 signal port i720 control port i722 dtm control string dtmf payload 101 rtp port i722 local type account gt call type advanced rtp tos po Fig 3 3 Protocol Setting e use service Enable disable service by checking clearing this box To make calls through SIP Proxy Server please check this box otherwise phone can only make IP to IP calls HOP1001 1002 SIP Phone User Manual e register ttl IP phone will send a keep alive registration message to SIP proxy server every register ttl seconds The minimum value is 10 maximum value is 65535 Default is 60 e jitter size Set buffer size of RTP package The value range is 0 32 e service type This option is used to accommodate the mi
26. ith handset picked or pressing speaker press this key to dial number gt Features gt Hardware e Main chip PA1688 50MHz e Data Memory 2MB SDRAM e Program Memory 1 MB Flash memory e Ethernet Jack 1 2 10 jacks HOP 1001 1 RJ45 10M jack HOP 1002 2 RJ45 10M jacks e AC DC adapter Input AC100 230V Output 9V DC 1A gt Software e DHCP support for LAN or Cable modem e PPPoE support for ADSL or Cable modem e Set phone by HTTP web browser IE6 0 or Telnet HOP1001 1002 SIP Phone User Manual Upgrade by FTP Support major G 7XX GSM610 audio codec VAD Voice active detect CNG Comfort noise generation Dynamic voice jitter buffer G 168 165 compliant 16ms echo cancellation Tone generation and Local DTMF re generation according with ITU T E 164 dial plan and customized dial rules 100 entries for quick dial 80 entries each for missed calls answered calls and dialed calls Adjustable volume for both handset and speaker Voice prompt Hotline gt Standard and Protocol HOP 1001 1002 IP Phone supports following standard and protocol e IEEE 802 3 802 3 u 10 Base T 100Base TX e Major G 7XX GSM610 audio codec e SIP RFC 2543 RFC3261 e TCP IP Internet transfer and control protocol e RTP Real time Transport Protocol e RTCP Real time Control Protocol e VAD CNG save bandwidth e DHCP Dynamic Host Configuration Protocol e PPPoE PPP Protocol over Ethernet e DNS Domain Name Server e Telnet
27. ith iptype set as 0 use this command to set router IP of network with HOP 1001 1002 IP phone set dns XXX XXX XXX XXX With iptype set as 0 use this command to set IP address of DNS server set dns2 XXX XXX XXX XXX With iptype set as 0 use this command to set IP of backup DNS server set mac XX XX XX XX XX XX Set MAC address of the HOP 1001 1002 IP phone Parameter XX XX XX XX XX XX must be an HEX number set service X Set register the SIP proxy server or not X ranged from 0 through 1 0 do not register 1 register set service type X Enable disable the repaid and service system choose the repaid server provider Parameter x ranged from 0 through 29 0 common disable repaid card 4 use Utstarcom system 12 use ZTE system 23 use sipphone service 24 use ipphonex service 25 use fwd freeworlddialup service 26 use net2phone SIP service 27 use stanaphone service 29 use iTalkBB system set serviceaddr XXXX 28 HOP1001 1002 SIP Phone User Manual Set IP address or domain name of SIP Proxy Server f the system has an Outbound Proxy set IP address or domain name of Outbound Proxy set serviceid XXXXX If the system has an Outbound Proxy Set the domain name of SIP proxy server such as Xxxx set nattraversal X X ranged from 0 through 7 0 do not use NAT traversal When the log in server and IP phone in the same LAN or the log in system supports the IP phone working behind the LAN 1 Use NAT traversal When the log
28. ke the call Once the call connection has been established and the ring tone has sounded wait for the other party to answer When the other party answers you can begin speaking When the call is over Press Speaker again The dialed number has been saved into the buffer e Place a call without login the SIP Proxy If HOP 1001 1002 IP phone does not login the SIP Proxy you can place a call by lifting the handset or pressing Speaker and then inputting the IP address of the other party and then pressing Note When you place a call without SIP Proxy or with Gateway please log off SIP Proxy To get the detailed operation please refer to Configuration chapter gt View Records e View missed calls Click Mis calls then you will see the record of missed call Click to turn the numbers orderly click to turn the numbers reservedly If there is no record you will see nothing e View received call Click Rec calls then you will see the record of the received un call Click to turn the number orderly clic to turn the numbers 41 HOP1001 1002 SIP Phone User Manual reservedly If there is no record you will see nothing e View dialed number Click Dial calls then you will see the record of the dialed call Click to turn the number orderly click to turn the numbers reservedly If there is no record you will see nothing When you see the number you want to dial
29. m O through 3 0 authorize users set IP address subnet mask and router IP address of IP phone manually 1 use DHCP mode With this system your LAN or router automatically assigns all the required network parameters to any device connected to it when the device log on HOP 1001 1002 IP phone is shipped from the 26 HOP1001 1002 SIP Phone User Manual factory with DHCP on So if your LAN or router is configured to use DHCP addressing the IP phone s LAN parameters will automatically be configured as soon as it is connected to the LAN or router and powered up 2 use PPPoE mode Those ADSL and Cable Modem users please select this item for it is a protocol especially designed for them With this system ADSL ISP automatically assigns all the required IP parameters to any device connected to it when the device log on 3 use modem mode Those who use IP phone with modem please set the value as 3 set pppid XXX With iptype set as 2 use this command to set ADSL ID with iptype set as 3 use this command to set Modem ID set ppppin XXX With iptype set as 2 use this command to set ADSL pin with iptype set as 3 use this command to set Modem pin set ip XXX XXX XXX XXX With iptype set as 0 use this command to set IP address of HOP 1001 1002 IP phone set subnetmask XXX XXX XXX XXX With iptype set as 0 use this command to set subnet mask of HOP 1001 1002 IP phone set router XXX XXX XXX XXX 27 HOP1001 1002 SIP Phone User Manual W
30. ne a disable Select this item when the log in server and IP phone in the same LAN or the log in system supports the IP phone working behind the LAN a enable When the system does not support IP phone working behind the LAN please select this item to search public IP address of the NAT device With this item selected nat addr field will be activated Besides port mapping port forwarding needs to be properly set up on NAT device a stun Select this item with SIP protocol used according to requirement of system With this item selected nat addr field is activated nat addr When nat traversal is set to enable please put the domain name of the servers These web server helps to find out the public IP of the IP phone into nat addr such as www whatismyip com When nat traversal is set to stun please put the URI of the stun server into nat addr in the format as domain name IP address service port The default service port for stun is 3478 nat ttl When IP phone sit behind a NAT device it will send packets to server every nat ttl seconds to keep the port mapping on the NAT device alive nat ttl is an integer between 10 and 65535 default value is 20 phone number The local phone number or username of this phone usually is allocated by system account With SIP system which requires authentication please put the username account into this field pin With SIP
31. p Case change Reserves the right to make changes in technical and product specification without prior notice 43
32. riority 4of the audio compression algorithm The options are g729 g7231 g711u g711a and gsm e codec5 Set the priority 5of the audio compression algorithm The options are g729 g7231 g711u g711a and gsm e g 723 1 high rate enable disable g 723 1 high rate G 723 1 high rate is 6 3kbps low rate is 5 3kbps e audio frame Set audio frames in RTP package Minimum is 1 and maximum is 8 e handset in Drag the slider to adjust the volume of handset input Drag it to the left to reduce the volume while drag it to the right to increase the volume e handset out Drag the slider to adjust the volume of handset output Drag it to the left to reduce the volume while drag it to the right to increase the volume e speaker out Drag the slider to adjust the volume of handfree output Drag it to the left to reduce the volume while drag it to the right to increase the volume Other settings other settings password 1234 super password 12345678 debug output x sntp ip 210 59 157 10 use daylight Cj upgrade addr timezone GMT 08 00 Beijing Hong Kong Urumqi x Fig 3 6 Other Setting Page e password Set the password of the phone Default password is 1234 HOP1001 1002 SIP Phone User Manual e super password Set the super password of the phone Default super password is 19800211 12345678 or 19750407 e debug Set the debug level of the phone a disable Disable output the debug message by selecting this item output Outpu
33. scellaneous requirements of the system providers When IP phone is connected to these systems please select the corresponding service type Common no special requirements utstarcom Use UtstarCom s SIP system zte Use ZTE s SIP system ngtel Use NGTEL s SIP system Sipphone Free SIP service on internet please visit www sipphone com for more information Inphonex Free SIP service on internet please visit www inphonex com for more information Fwd Free SIP service on internet please visit www freeworldialup com for more information net2phone Use Net2phone s SIP system stanaphone Use Stanaphone s SIP system italkbb Use ItalkBB s SIP system e service addr service id If use service is checked please put the URI of the SIP proxy server into service addr Put the domain name of the SIP proxy server into service id or leave service id empty If the system has an Outbound Proxy please put the URI of the Outbound proxy into service addr and put the domain name of SIP proxy server into service id The default service port is 5060 If use service is not checked please clear HOP1001 1002 SIP Phone User Manual service addr and service id nat traversal When the IP phone with private IP address need communicate with other IP phones in a different LAN or on Internet please select an item from dropdown list to set the proxy used by the pho
34. t the operation information to the window such as register input by selecting this item a output all Output all debug information and data in test window by selecting this item remote debug Save the debug information in SDRAM of IP phone by selecting this item no check Disable checking firmware tags when upgrading This is not suggested because it will increase the risk of upgrading the wrong firmware into the phone e upgrade addr Put IP address or domain name obtained by ISP of FTP server supplying upgrade program into this field e nts ip Fill IP address of time server here e use daylight Enable disable daylight e timezone Select correct time zone in list box When debug set as O disable if input ordinary password default one is 1234 then following page will pop up after clicking __1 s n__ And only those parameters can be modified 20 HOP1001 1002 SIP Phone User Manual network settings iptype dhcp v ppp id OoOo O PPP pin Po local ip 192 168 1 212 subnet mask 255 255 255 0 router ip 192 168 1 254 as 202106 46 1651 aa 202 96 128 68 protocol settings TEENE iat ll phone number por tts account aaa rtp port i722 register port jiT20 signal port jiT20 control port i722 phone settings ring type dtmf0 x forward number 82378009 fwd always D fwd noanswer Iv fwd poweroff O fwd busy mn answer fo other settings password i234 wessa o sntp ip 210 59 157 10 use daylight r timezone GNT 08
35. ut the IP address of the phone into address bar and then input super password 19800211 19750407 or 12345678 Then click login button 3 Set debug to no check then click Update button 4 Run palmtool exe 5 Input the IP address of the phone into IP Address in Chip field and then click Update Program button 6 Select Updated program bin and then click ok 7 After end of delivering it will show prompt information on screen which is Updating please wait until the update led stop on and off It needs some time to update telephone program it will show Ready for Call on screen if there is a LCD in telephone when succeed updating and the updating is OK gt Set FTP server FTP server can be supplied by the server provider as well as setup by the users in LAN Please set the IP address of FTP server gt Usage of the phone gt Receiving calls HOP 1001 1002 IP phone can receive incoming calls from other HOP 1001 1002 IP phone and devices that support the SIP protocol It works just like an ordinary phone for incoming calls When it rings you can receive the call by following methods Use handset Lift the handset and begin speaking When the call is over put the handset back 2 Handset to hand free While receiving call with handset press Speaker 39 HOP1001 1002 SIP Phone User Manual on the keypad and then put down the handset When the call is over press Speaker again

HOP-1001/1002 SIP Phone User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents