ET-12 roller door opener instruction manual
Contents
1. left hand limit switch will be reversed STEP1 Remove Limit Switch Cover Plate Figure 7 See Figure 6 by carefully prising off with a small screwdriver ES STEP2 Top limit cam T controls open position of door Bottom limit cam B controls closed Mi position of door STEP3 9 Slightly loosen the three retaining screws pan Retaining Screws so that the cams can be easily moved See Figure 7 STEP4 Ensure that the manual release lever is still in the disengaged position and manually raise the door until it is approx 100mm from the top position STEP5 Rotate cam T in the same direction that is was moving as you were manually raising the door so that it actuates the top Limit Switch STEP6 Manually lower the door until it is touching the ground STEP7 Rotate cam B in the same direction that is was moving as you were manually lowering the door so that it actuates the bottom Limit Switch STEP8 Tighten the three retaining screws so that the sams will not move STEP9 Manually position door to halfway and reengage the motor drive by moving the manual release lever to the engage position N B Door can now only be operated electrically not manually If you wish to return to manual operation ensure power is switched off and move lever to disengage position STEP10 Connect the two motor wires Spade Connectors Refer Figure 8 to loose wires from the Limit Conne2. Battery Voltage Coding Format ACCESSORY OPTIONS Additional remote control transmitter Infrared beam Additional safety feature Manual release lock External receiver 220VAC 10 24VAC 20 C 70 C Permanent Magnet D C Motor 24V DC 24V DC 5V DC 36V 1 5W Receiver type 433MHz 315 MHz RF Frequency 433MHz 315MHz Control distance 50m max 433MHz 315 MHz 12 Volts A23 battery Rolling Code 7 38X10 Code Combinations
3. INSTALLATION INSTRUCTIONS AND OWNERS MANUAL ET 12 Roller Door Motor IMPORTANT PLEASE READ THERE INSTRUCTIONS CAREFULLY PRIOR TO COMMENCING THE INSTALLATION OF THE OPERATOR UNIT This Automatic motor has been designed to provide years of trouble free use The motor will perform efficiently only if it is installed and operated properly READ THESE IMPORTANT SAFETY RILLES FIRST Keep garage door balanced Sticking or binding doors must be repaired Garage doors door springs brackets and their hardware are under extreme tension and can cause serious personal injury Do not attempt adjustment Call for professional garage door service Do not wear rings watches or loose clothing while installing or servicing a garage door operator Installation and wiring must be in compliance with your local building and electrical codes The safety reverse system test is very important Your garage door must reverse on a contact with a 5 to 10cm high object on the floor Failure to properly adjust the operator may result in serious personal injury from a closing garage door Repeat the test once a month and make any needed adjustments see Sensitivity adjustment ET motor has an electronic obstruction ayatem that provides safe and reliable operation It is however a legal requirement in some countries to also install a Photo electric sensor across the door way Please check this requirement with your local distributor Do not use the force adjustm
4. ctors Switches Switch on power to the Control Box and operate the door from PUSH Button on the Control Box Figure 8 Figure 9 IMPORTANT When the door is traveling in the Up position hold bottom rail The door should overload and stop If it does not reverse motor wires Spade Connectors You will need to re adjust the Limit Cams as they will be working in a different direction STEP11 Press Button on Control Box Front and check closing and opening position STEP12 If you are achieving the desired stop position closing and opening then replace the Limit Switch Cover Plate If not then reset the Limit Cams Steps2 to 9 after first turning off the mains power STEP13 Once the limits have been set fit the additional security screws 2 of self tapping screws supplied with the door in manual mode With the door fully closed mark the panel at the first point where the curtain roll touches the drum wheel on both ends of the curtain See Figure 9 Raise the door slightly so that the marks can be seen and accessed from inside the garage Fit the security screws through the bottom of a corrugation and into the plastic flange of the drum wheel on both ends of the curtain Tighten securely WARNING Do not run door on power through its full reavel unit the limits are correctly set Control box set up Remove cover on front of control box 1 Wiring diagram B1 B2 AC24V transformer outp
5. eam sensor can be supplied as an accessory option OPERATING CONTROLS 1 Control Box Push Button Pressing this button will open close or stop the door 2 Hand transmitter Each button is programmed to have three functions to open close and stop the door Key Ring Handset optional The hand transmitter is manufactured using the latest surface mount technology and incorporates 4 functional buttons This enables the user to remotely control up to 4 separate operators from the one handset FAULT FINDING DOOR WILL NOT OPERATE FROM A Control Box Check power is on to Control Unit Green L E D illuminated IF NOT check mains plug and fuse Plug fully engaged on top of Control Box Motor wiring connections properly engaged Manual release lever in engaged position Limit Switch cams correctly set i e upper Limit Switch for fully open position lower Limit Switch for fully closed position Move door manually to half closed position and try again Try operation with Hand Transmitter B On hand Transmitter Check door operates correctly using the Push Button on Control Box to prove systems is okay Try recoding Transmitter Check battery in Transmitter is correctly fitted L E D should illuminate Try new battery DOOR OPERATES BUT FAILS TO FULLY OPEN OR REVERSES BEFORE CLOSING Check manual operation for correct balance not binding Adjust if necessary Spray silicone lubricant into tracks Do not gr
6. ease Check adjust safety sensitivity setting Check Limits BANGS HAD ON TRACK STOPS WHEN FULLY OPEN Check top Limit Switch setting Adjust if necessary BANGS HARD ON GROUND AND REVERSES WHEN FULLY SHUT Check bottom Limit Switch setting Adjust if necessary DOOR FAILS TO TRAVEL DOWN FROM OPEN POSITION MOTOR RUNS AND ROLLER DOOR BALOONS Check door curtain has smooth line of entry into tracks as near vertical as possible Check door tension is not too great reduce spring tension if necessary If the above does not cure the problem then the door may require a weight bar to be fitted SHOT RANGE REMOTE CONTROL Remote Control should give minimum of 6m range Check battery is correctly fitted in Transmitter Try new battery DOOR OPERATES BUT FAILS TO FULLY OPEN BUT REVERSES TO CLOSED POSITION Change Motor Wire Spade Connectors Reset Limits Re adjust Sensitivity Adjustment POWER FAILURE To disengage Pull manual release lever downwards refer fig3 To engage Push manual release lever up Technical Specifications 110VAC 60Hz or 127VAC 60Hz available on request INPUT VOLTA 220VAC 10 50Hz Single Phase TRANSFORMER SEPC Primary Voltage Secondary Voltage WORKING CIRCUMSTANCE TEMPERATURE MOTRO SPEC Motor Type Voltage CONTROL BOARD SPEC Control Board Voltage Light Globe Voltage Receiver specification built in TRANSMITTER SPEC Carrier Frequency
7. ent to compensate for a binding or sticking garage door Excessive force will interfere with the proper operation of the Safety Reverse System or damage the garage door This unit should not be installed in a damp or wet space Disengage all existing garage door locks to avoid damage to garage door Install the lighted door Control Box or any additional Push Buttons in a location where the garage door is visible but out of the reach of children Do not allow children to operate push button s or remote control s Serious personal injury from a closing garage door may result from misuse of the motor CAUTION Activate motor only when the door is in full view free of obstructions and motor is properly adjusted No one should enter or leave the garage while the door is in motion Do not allow children to play near the door Disconnect electric power to the garage door motor before making repairs or removing covers IMPORTANT Fix the caution label supplied to the rear of the garage door as a reminder of safe operating procedures Pre Installation Notes door curtain En U bolts PF gt ye r Cast iron saddle A pn Ea gt A ad Mounting bracket Remote contre figure 1 i lead 1E right hand installation shown inside looking out N B The right hand and left hand installation could be swaped on printed circuit board Please refer to control box set up Check that there is sufficient side clea
8. learning button in the control box for about 10 seconds until the LED indicator go out all transmitters codes held in the memory have been erased N B If a transmitter is lost or stolen please erase the memory and re learn any spare or new transmitters OWNER S MANUAL DOOR OPERATION A roller door equipped with a roller door motor may be operated by any of the following two methods by using the hand held transmitter by pressing the push button on the control box mounted on the wall WARNING Ensure that the Centre Lift Lock is not engaged when the Drive Unit is in the automatic position Manual Operation In the case of a power failure the drive unit has an easily accessible manual release lever the door could be opened manually Obstruction Detection During an open cycle is an obstruction is detected the door will stop During a closing cycle is an obstruction is detected the door will reverse to the open position The sensitivity or the amount force required to cause an obstruction detection is fully adjustable Courtesy Light An internal courtesy light is housed within the control box enclosure This is activated during an open or close cycle and will stay illuminated for approximately 180 seconds Auto Closing The motor can be programmed to automatically close 60 seconds after the door has been opened Photo electric sensor The motor includes an interface for the connection of a photo beam sensor The photo b
9. rance to fit the motor unit It may be fitted to either the right or left hand side 1 Minimum side clearance ETEN The minimum side clearance between door NE ledige curtain and the inside edge of mounting bracket is 85mm The minimum side clearance between door curtain and the outside edge of mounting bracket is 135mm z Figure2 2 Recommended side clearance The recommended side clearance between r 100 door curtain and the inside edge of mounting MO bracket is 110mm The recommended side clearance between door curtain and the outside edge of mounting bracket is 160mm Figure3 If the motor is being fitted at the same time as the new door installation read these instructions in conjunction with the ET roller door installation instructions If the motor is being retro fitted make sure the door motor smoothly and is properly balanced N B SPECIAL CARE SHOULD BE TAKEN IF RE TENSIONING OF THE DOOR IS REQUIRED At no stage should you loosen both U bolts if door is under tension IF THERE ARE ANY PROBLEMS PLEASE CONTACT YOUR LOCAL SUPPLIER OF THIS MOTOR INSTALLATION INSTRUCTIONS Figure 4 STEP1 Whilst the door roll is on the floor rotate shaft backwards and forwards by hand and then release This action will allow the roll to centralize itself on the shaft New installation only STEP1 Fit position clamp TIGHT TO DRUM at opposite end of curtain to the motor u
10. sing M8 Dome Head Screw and M8 Nyloc Nut as required Figure 4 STEP3 Slide drive unit onto shaft as shown Figure 5 Ensuring drive lugs engage fully with the narrowest spoke on drum wheel Figure 6 N B Right hand installation shown inside looking out Lift door onto mounting brackets ensuring curtain roll is correct way round centralize curtain roll with opening Refer to door installation instructions New installations only Ensure motor assembly is fully engaged with drum wheel spokes Clamp shaft to mounting brackets using U Bolts supplied Use U bolt in motor pack for MOTOR end See Figure 6 Disengaged the motor drive by pulling the manual release lever downwards See Figure 6 Tension door and complete door installation as per Door Installation Instructions Ensure door is correctly balanced and is not binding or sticking within vertical reacks Ensure locking bars if fitted are moved to the retracted unlocked position and keys removed from the lock Mount Control Unit approximately 1 6m from the floor out of the reach of children Use 4pcs of 4 30mm self tapping screws and rawplugs supplied Ensure aerial is clear of all steel supports and coiled electrical leads Fit plug from motor unit into bottom of Control Box Connect the control unit power cord to an adjacent socket Ensure that the socket is properly earthed SETTING TOP AND BOTTOM LIMITS N B Right Hand Installtation only If
11. ut M1 M2 motor A A Manual push button 24V OV I infrared beam LAMP 36V 1 5W light socket 3 Auto close option switch1 1 in E position auto close features on switch1 1 in D position auto close features off N B mandatory Photo Eye Protection must be used for this option Contact your local supplier 4 Right hand and left hand installation swap switch 1 2 in R position is for right hand installation switch 1 2 in L position is for left hand installation 5 Sensitivity adjustment For right hand installation 1 adjust pot Down for downward traveling sensitivity clockwise is for big force and the anti clockwise is for small force 2 adjust pot Up for upward travelling sensitivity clockwise is for big force and the anti clockwise is for small force Whilst the door is travelling turn the obstruction sensitivity pot slowly until an overload condition occurs i e door going up stops before reaching the set top limit or door going down auto reverses before reaching set bottom limit Cycle the door a few times ensuring an overloading conditions is not registered during normal operation PROGRAMMING HANDSETS TO NEW CONTROL BOX Press and release the white learning button learn LED indicator will light and go out then press the handset key which will operate the door the handset transmitter is now programmed For multiple handsets code them the same as above mentioned To delete all codes Press and hold the
Download Pdf Manuals
Related Search