User's Guide 400A AC Clamp Meter Model MA200
Contents
1. is displayed After 15 minutes 2 per second nominal 7 8MQ V DC and V AC 41 F to 104 F 5 C to 40 C 4 F to 140 F 20 C to 60 C Max 80 up to 87 F 31 C decreasing linearly to 50 at 104 F 40 C lt 80 6560ft 2000meters 2 1 5V AAA batteries 0 44lb 200g 7 87 x 1 97 x 1 38 200x50x35mm For indoor use and in accordance with the requirements for double insulation to IEC1010 1 1995 EN61010 1 1995 Overvoltage Category III Pollution Degree 2 3 MA200 Version 1 4 06 06 Meter Description ON 09 012 nN 20 AC DC AUTO MAX HOLD Transformer jaws MAX Hold button Hold button LCD Display COM Input Terminal Jaw opening trigger Function select switch Voltage Resistance Input Terminal Mode Select Button Backlight Button Range Select Button Alternating current Direct currrent AutoRange mode MAX Hold mode Diode test mode Audible Continuity Data Hold mode Low Battery icon EXTECH INSTRUMENTS 400A AC Clamp on 00 HE AUTO m LI MA200 Version 1 4 06 06 Operation NOTICES Read and understand all warning and precaution statements listed in the safety section of this operation manual prior to using this meter Set the function select switch to the OFF position when the meter is not in use AC Voltage Measurements Set the rotary function switch to the VAC position 2 Insert the black test lead banana plug2. support extech com Repair Returns Ext 210 Email repair extech com Website www extech com Copyright 2003 Extech Instruments Corporation All rights reserved including the right of reproduction in whole or in part in any form 8 MA200 Version 1 4 06 06 YI 1BUR This datasheet has been downloaded from www EEworld com cn Free Download Daily Updated Database 100 Free Datasheet Search Site 100 Free IC Replacement Search Site Convenient Electronic Dictionary Fast Search System www EEworld com cn All Datasheets Cannot Be Modified Without Permission Copyright Each Manufacturing Company
3. into the negative COM jack and the red test lead banana plug into the positive V Q jack 3 Touch the test probe tips to the circuit under test Read the voltage in the display The display will indicate the proper decimal point and value DC Voltage Measurements Set the rotary function switch to the VDC position 2 Insert the black test lead banana plug into the negative COM jack and the red test lead banana plug into the positive V Q jack 3 Touch the test probe tips to the circuit under test Be sure to observe the correct polarity red lead to positive black lead to negative 4 Read the voltage in the display The display will indicate the proper decimal point and value If the polarity is reversed the display will show minus before the value E Voltage 5 MA200 Version 1 4 06 06 AC Current Measurements WARNING Ensure that the test leads are disconnected from the meter before making current clamp measurements Set the Function switch to the 400 or 200A range If the range of the measured is not known select the higher range first then move to the lower range if necessary Press the trigger to open jaw Fully enclose one conductor to be measured The clamp meter LCD will display the reading Resistance Measurements 1 Set the function switch to the 2 BH position 2 Insert the black test lead banana plug into the negative COM jack Insert the red test lead banana plug into
4. the positive VQ jack 3 Touch the test probe tips across the circuit or part under test It is best to disconnect one side of the part under test so the rest of the circuit will not interfere with the resistance reading 4 Read the resistance in the display The display will indicate the proper decimal point and value Continuity Check 1 Set the function switch to the Q Pt position 2 Push the mode button to indicate on the display 3 Insert the black lead banana plug into the negative COM jack Insert the red test lead banana plug into the positive VQ jack 4 Touch the test probe tips to the circuit or wire you wish to check 5 If the resistance is less than approximately 300 the audible signal will sound If the circuit is open the display will indicate OL Continuity wire 6 MA200 Version 1 4 06 06 Diode Test 1 Turn the rotary switch to the Q Pt position 2 Insert the black test lead banana plug into the negative COM jack and the red test lead banana plug into the positive VQ jack 3 Push the mode button to indicate gt t on the display 4 Touch the test probes to the diode under test Forward voltage will indicate 400 to 700mV Reverse voltage will indicate OL Shorted devices will indicate near OmV Shorted devices will indicate near OmV and an open device will indicate OL in both polarities Data Hold To freeze the LCD meter reading pr
5. User s Guide EXT NSTRUMENTS 400A AC Clamp Meter Model MA200 Introduction Thank you for selecting the Extech MA200 AC Clamp Meter This meter measures AC Current AC DC Voltage Resistance Diode Test and Continuity This professional meter with proper care will provide years of safe reliable service Safety International Safety Symbols This symbol adjacent to another symbol or terminal indicates the user must refer to the manual for further information This symbol adjacent to a terminal indicates that under normal use hazardous voltages may be present Ol Double insulation A UL mark does not indicate that this product has been evaluated for the accuracy of its readings Pb SAFETY NOTES e Do not exceed the maximum allowable input range of any function e Do not apply voltage to meter when resistance function is selected e Set the function switch OFF when the meter is not in use e Remove the battery if meter is to be stored for longer than 60 days WARNINGS e Set function switch to the appropriate position before measuring e When measuring volts do not switch to current resistance modes e Do not measure current on a circuit whose voltage exceeds 240V e When changing ranges using the selector switch always disconnect the test leads from the circuit under test e Do not exceed the maximum rated input limits OVERVOLTAGE CATEGORY III This meter meets the IEC 610 1 95 stand
6. ard for OVERVOLTAGE CATEGORY III Cat III meters are protected against overvoltage transients in fixed installation at the distribution level Examples include switches in the fixed installation and some equipment for industrial use with permanent connection to the fixed installation 2 MA200 Version 1 4 06 06 Specifications Function Range Accuracy of reading AC Current 2 000 ACA 2 5 10 digits 20 00 ACA 2 5 4 digits 200 0 ACA 2 5 4 digits 400 ACA 3 0 5 digits AC Voltage 200 0mvV 1 5 30 digits 2 000V 20 00V 1 5 3 digits 200 0V 600V 2 0 4 digits DC Voltage 200 0mV 0 5 5 digits 2 000V 20 00V 1 2 3 digits 200 0V 600V 1 5 3 digits Resistance Q 200 0 1 0 4 digits 2 000k 20 00k 1 5 2 digits 200 0k 2 000M 2 0 3 digits 20 00M 3 0 5 digits Jaw size Display Continuity Diode Test AC V bandwidth AC A bandwidth Low battery indication Overrange indication Auto Power OFF Measurement rate Input Impedance Operating Temperature Storage Temperature Operating Humidity Storage Humidity Operating Altitude Batteries Weight Size Safety 0 9 23mm approx 3 1 2 digits 2000 counts LCD Audible tone lt 120Q approx Open circuit voltage lt 1 5VDC Test current 0 3mA typical 50Hz to 400Hz 50 60Hz BAT is displayed OL
7. ess the data hold button The data hold button is located on the left side of the meter bottom button While data hold is active the HOLD display icon appears on the LCD Press the data hold button again to return to normal operation MAX Hold To hold the highest reading on the LCD press the MAX button The max hold button is located on the left side of the meter top button While data hold is active the MAX display icon appears on the LCD The meter reading will not change as readings change rather it will only display the highest reading encountered since the max hold button was pressed Press the max hold button again to return to normal operation 7 MA200 Version 1 4 06 06 Maintenance WARNING To avoid electrical shock disconnect the meter from any circuit remove the test leads from the input terminals and turn OFF the meter before opening the case Do not operate with open case Cleaning and Storage Periodically wipe the case with a damp cloth and mild detergent do not use abrasives or solvents If the meter is not to be used for periods of longer than 60 days remove the batteries and store them separately Battery Replacement 1 Remove the two rear Phillips head screws 2 Open the battery compartment 3 Replace the two 1 5V AAA batteries 4 Re assemble the meter Warranty EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for one year from date
8. of shipment a six month limited warranty applies on sensors and cables If it should become necessary to return the instrument for service during or beyond the warranty period contact the Customer Service Department at 781 890 7440 ext 210 for authorization A Retum Authorization RA number must be issued before any product is returned to Extech The sender is responsible for shipping charges freight insurance and proper packaging to prevent damage in transit This warranty does not apply to defects resulting from action of the user such as misuse improper wiring operation outside of specification improper maintenance or repair or unauthorized modification Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct indirect incidental or consequential damages Extech s total liability is limited to repair or replacement of the product The warranty set forth above is inclusive and no other warranty whether written or oral is expressed or implied Repair and Calibration Services Extech offers complete repair and calibration services for all Extech products For periodic calibration NIST certification or repair of any Extech product call customer service for details on services available Extech recommends that calibration be performed on an annual basis to insure calibration integrity T Support Hotline 781 890 7440 Tech support Ext 200 Email
Download Pdf Manuals
Related Search