USER MANUAL OF THE PROGRAM CARD FOR THE
Contents
1. d Connect the main power pack to the ESC e After several seconds the digit LEDs on the program card light to show the current programmable value of the ESC Note The sequence of step b c and step d cannot be reversed Otherwise the program card cannot work properly And do not use a battery pack more than 6V to supply the program card OPERATION Press the ITEM button to select the programmable items in a loop The serial number of the programmable items will be shown by 2 digit LEDs marked with ITEM and the current value corresponding to the selected programmable item will be shown by another digit LED marked with VALUE Press the VALUE button to choose the parameter value you need After that press the OK button a bright symbol appears in the middle position of the digit LED marked with VALUE for about 1 2 seconds that means the new setting is accepted and stored in the ESC The RESET button is used for restoring all the items of the ESC to the default vales DECLARATION The program card is ONLY suitable for the ESC of the same manufacturer2. User Manual of the Program Card for the Car ESC USER MANUAL OF THE PROGRAM CARD FOR THE CAR ESC FUNCTION AND FEATURE Thank you for purchasing the program card for the car ESC Electronic Speed Controller The program card has a friendly user interface so you can easily set the programmable parameters of the ESC with this device It is pocket sized so you can bring it to the racing field conveniently SPECIFICATION 1 2 Size 88mm 58mm 14mmM Wight 40g PROGRAMMABLE ITEMS 1 Running Model a Forward with brake mode it provides forward and brake functions b Forward Reverse with brake mode it provides forward backward and brake functions Drag Brake Force When the throttle stick is moved from the forward range to the neutral rang a bit brake force is created by the ESC to simulate the slight braking effect of a neutral brushed motor while coasting This item has 8 options from 0 to 40 with the increased drag brake force Low Voltage Cut Off The function is mainly to prevent the lithium battery pack from over discharging When using lithium battery pack please set the suitable value for low voltage protection as you like Never use the default value Non protection for lithium battery Start Mode This item adjusts the start force when the motor begins to run sometimes we call it Punch For XeRun series ESC there are 9 options for this item from Level 1 to Level 9 with the incre
3. ased start force For eZRun series ESC there are only 4 options for this item from Level 1 to Level 4 with the increased start force Maximum Brake Force It refers to the force when the throttle stick is located at the top point of the backward zone A very large brake force can shorten the brake time but it may damage the gears This item has 4 options from 25 to 100 with the increased maximum brake force Maximum Reverse Force Different value makes different reverse speed This item has 4 options from 25 to 100 with the increased maximum reverse force Initial Brake Force It is also so called minimum brake force and it refers to the force when the throttle stick is located at the initial position of the backward zone Throttle Neutral Range This item is used to set the throttle neutral range so it can be compatible with the habit of different users This item has 3 options from 6 to 12 with the increased neutral range Timing This parameter is only available for brushless motor There are many differences among structures and parameters of different brushless motors so a fixed timing ESC is difficult to compatible with all brushless motors It is necessary to make the timing value programmable Please select the most suitable timing value according to the motor you are just using Generally higher timing value brings out higher power output but the whole efficiency of the system will be slightly lower down 10 Mot
4. or Type a Brushless motor Doc Ver HW 10 080619 1 b Brushed motor forward and reverse with brake c Brushed motor forward only without brake 11 Over Heat Protection If the function is activated the output power will be cut off when the temperature of the ESC is higher than a particular value WIRING SEQUENCE 1 When you are using an ESC with a built in BEC Battery Elimination Circuit a Disconnect the power pack from the ESC b Disconnect the BEC cable of the ESC trio wires form your receiver then connect it to the program card at the top right corner position marked with Lf c Connect the main power pack to the ESC d After several seconds the digit LEDs on the program card light to show the current programmable value of the ESC Note The sequence of step b and step c cannot be reversed Otherwise the program card cannot work properly 2 When you are using an ESC without a built in BEC If the ESC hasn t a built in BEC you must use an additional battery pack 4 8 V 6V to power the program card Please connect the battery to the program card at the top right corner position marked with Usually a receiver battery pack is a good choice a Disconnect the power pack from the ESC b Disconnect the BEC cable of the ESC trio wires form your receiver then connect it to the program card at the top right corner position marked with 9 BU c Connect the additional battery pack to the program card at the top right corner
Download Pdf Manuals
Related Search