LANsmart Pro user manual Introduction LANsmart Pro is a hand
Contents
1. Fail Fail Length Test LANsmart Pro can measure the length of twisted cable flat telephone line and coax line Before test user should setup the type of cable to be tested in the Configuration menu For standard twisted cable user should setup Configuration Cat5 Cat5e or Cat6 For non standard twisted cable flat telephone line and coax line user should calibrate parameter by using a criterion cable first It is operated by Configuration Calibration menu Select Length from LANsmart Pro Main Menu Cable Test gt Length Test Identification Configuration Main Menu Please User should take off remote or it will lead to take off remote inaccurate result Yes First LCD displays the average length Ntwk 93 8 M for Meter and Ft for Feet gt Pairs Length By selecting Pairs Length operation user can see pair length Bulk cable length measurement To measure the length of bulk cable 1 Peel off the cable jacket of the Green Green white wires 2 Use the attached cable in the package RJ45 plug to two alligator clip 3 Plug one end of RJ45 to the Main unit and the other end to the two alligator clips Green clips to the Green wire and White clips to the Green white wire 4 Test the cable length Tone Generator At 1 KHz frequency the LANsmart Pro emits an audio signal to a cable user can trace the cable with corresponding cable tracer Select the Analog Tone options fro2. prior to use When choosing wire map test object twisted cable telephone line or coax line and calibrating parameters for non standard cable length test user must do the following configuration Follow the steps to configure the LANsmart Pro 1 Turn on the LANsmart Pro 2 LANsmart Pro will self diagnose first 3 Press the SELECT button to choose desired Configuration indicated by arrow Cable Test Length Test Identification gt Configuration Main Menu 4 Pressthe ENTER button and view menu options a On Meter Feet option press ENTER to select desired measurement Meter M or Feet F gt Meter Feet M gt Meter Feet Ft Cable Cable Length Length Modify Zero t Modify Zero t Configuration page Configuration page c When first using LANsmart Pro you can select Modify Zero menu note nothing inserted to Jack press ENTER to modify Zero d On Cable option press ENTER to test wire map of twisted cable Tel line or Coax line Ntwk Tel Coax A e On Length option press ENTER to open the Length setting mode Calibration Cat5 5e Cat6 f On the Calibration option press ENTER to open the calibration mode Calibration Ntwk Cal Cat5 5e Tel Cal Cat6 Coax Cal In order to increase measuring accuracy for cable length test the setup is used to adjust calibrating parameters for non standard cables It includes twisted cables flat phone lines and coa
3. LANsmart Pro user manual Introduction LANsmart Pro is a hand held multifunction Cable Map Tester and Cable Length Meter It has an integrated Analog and Digital Tone Generator Port Finder and Quick Test It displays cable map results in a pin to pin format including split pairs By using TDR Time Domain Reflect technology it provides a great deal of accuracy when measuring cable length and locating split pairs It is suitable for professional technicians or installers Features All in one tester wire map twisted mapping short location quick test cable length test self calibrating ability analog and digital tone generator and port finder Incorporates TDR Time Domain Reflect Technology Wire map for open short reversed cross split miswire and shield continuity Wire map results are displayed in a pin to pin format Indicates the remote number of the remote identification unit for wire map test Incorporate Short Location function locate short position it determines if short is in the near or far end of the cable Measures twisted pairs of Cat5 Cat5E and Cat6 length without remote Measures length of flat 2 pin 4 pin and 6 pin telephone line Measures coax line length Self calibrating ability for non standard cables length test to enhance measuring accuracy Uses both meter and feet standards for cable length display Incorporate Quick Test function memorize a cable s pin out as standard and test mass cables Inc
4. ch end of cable are shorted by using TDR technology Also user can see short details on Wiremap menu 1 3 1 Pair 1 1 2 are shorted at near side of 2 6 cable TX 2 Pair 2 3 6 are shorted at far side of cable gt OK t RX Short details display No pins are shorted No short detected gt t More than 2 pins are shorted one point Too much short Quick Test This function is used to test a number of cables First LANsmart Pro records a cable pin out status We call it standard cable Next it tests another cable to judge whether the tested cable s pin out status is the same to standard cables By this user can test numerous cables Select the Cable Test option from the Main Menu then select Quick Test Wiremap Twisted Mapping Short Location P Quick Test First record a cable s pin out as test standard User should connect the standard cable with the main unit and the remote unit Then select Record Cable gt Record Cable Test Cable When recording is completed the beeper Beeps Bi and the LCD display a message Cable Recorded Cable Recorded Then select Test Cable for mass cable testing Record Cable gt Test Cable t If the cable s pin out is the same as the standard Pass cable the beeper beeps Bi Bi and LCD displays Pass If the cable s pin out is different form the standard cable the beeper beeps Bi Bi Bi and LCD displays
5. ith shields layer LANsmart Pro will automatically display it first The following explains the Wiremap results in details 12345678G Pin7 and Pin8 are open 123456 G Open Id3 12345678G Pin2 and Pin5 are short Short 1d3 12345678G 36145278G Cross Id3 Pair1 2 and Pair3 6 are cross 12345678G 12345678G Id3 gt Pair1 2 and Pair3 6 are split Split 12345678G 21345678G Pin1 and Pin2 are reversed 143 Rev 12345678G 12345678G All pins are ok 143 12345678G 81275643 Pins are miswire Id3 LANsmart Pro can also identify and indicate the remote identification number attached to the far end of the subject cable 12345678G 12345678G The number of remote identification unit is 3 Id3 Twisted Mapping The cable s twisted status can be analyzed and shown as map by selecting the Twisted mapping option from the Cable Test Menu Wi 5 i i In Twisted mapping mode remote unit should be removed from the end of cables Otherwise test result will be inaccurate gt Twisted Mapping Short Location Quick Test Please A warning will be displayed for unplugging the remote unit Select Yes to continue Select t go to previous menu take off remote Yes If the cable is shorter than 1 2 meter the LANsmart Pro can not identify the twisted status it will show the warning message Cannot detect cable under 1 2m Short Location LANsmart Pro can show whi
6. m Identification menu Cable Test ENTER gt Analog Tone ENTER ee ENTER Digital Tone gt Identification Port Finder Configuration User can select the pins to send the tone signal PIN 1 2 3 4 The Selected pin will be highlighted gt 5 6 7 8 Select t to stop Tone mode and return to previous All Pins t menu Note Under normal conditions Tone on all pins will be louder than Tone on single pin Select the Digital Tone options from Identification menu Select Single tone or Double Tone from Digital Tone Press ENTER to send Digital Tone Single Tone Double Tone Sending Sending Port Finder Port finder is a distinctive feature Professionals recommend it It is used to identify correct ports the cable is using The correspondent port s LINK LED will blink once the LANsmart Pro sends 10M fast link signals through the cable Cable labeling has just become so much easier Cable Test Length Test Analog Tone Digital Tone Port Finder Identification Configuration Single Sending LANsmart Pro sends fast link signals until t is selected 10 Port Finder menu Warning Telephone line connection When LANsmart Pro s RJ45 RJ11 port is connected to an active telephone line it sends out a warning message High Voltage Detected Please Reset and causes all function module to stop working You must immediately turn off the unit Thank you for choosing Hobbes Corporation another i
7. nnovation that is designed to improve trouble shooting network performance and productivity We are dedicated to providing the best quality and value for all your electronics needs Whether it s for individual corporate or governmental use Hobbes has the solution for you End 11
8. orporates Port Finder function locate corresponding socket on hub switch Its Analog Tone Generator sends 1K Hz tone on all pins or selected single pin conductors Its Digital Tone Generator sends Single Tone and Double Tone LCD and beep indicator RJ45 RJ11 COAX port protection from telephone line damage Replaceable battery with low battery indicator Contents 1 LANsmart Pro Main Unit 4 Remote Unit ID1 ID2 ID3 ID4 Specifications Display 128 64 Dot Matrix LCD Connector Type RJ45 RJ11 COAX Main and Remote Accuracy 2m less than 10m 6 56 Feet in less than 32 81 feet 5 over 10m 32 81 feet Test range for cable length 0 300m 0 984 feet Split pairs detection minimum 1 2m 3 94 feet Analog Tone Generator 1 KHz Digital Tone Generator Single Tone and Double Tone Operating Temperature 0 C 50 C 32 F 122 F Storage Temperature 30 C 50 C 22 F 122 F Humidity 10 90 Weight Main unit 120g Remote unit 20g Dimensions Master 120 80 33mm Remote 44 42 28 5mm Power source DC6V 4 AAA LANsmart Pro Manual Operation It is recommended to check the battery conditions before use A low battery will lead to inaccurate test results Main buttons function SELECT Change or navigate the arrow on the screen gt ENTER Execute the operation selected by the arrow Default Configuration In order to perform properly user should set up the Configuration menu
9. x lines For example network cable calibration page explanation Ntwk Cal 10 M e Ntwk the calibration object is network twisted pair e Cal xx M It is the cable length supplied by LANsmart Pro when using default parameter e and to change the Cal value increase or decrease e YES to save the setting t to go back or return to previous menu e Adjustable Cal value is from 10M to 150 M g Complete the setup and save the setting then the Main Menu is displayed h The Cat5 CatSe and Cat6 mode denotes the LANsmart Pro is using default factory parameter for testing standard Cat5 Cat5e or Cat6 cable length Wire map Test Before wire map test user should setup test object twisted cable telephone line or coax line in Configuration menu Connect one end of tested cable to LANsmart Pro main unit and the other to the remote Select the Cable Test option from the Main Menu and then select Wiremap LANsmart Pro will begin to diagnose on the attached cable gt Cable Test gt Wiremap ENTER ENTER mona Twisted Mapping Identification Short Location _ Configuration Quick Test Main Menu Cable test menu 12345678G Transmitting side main unit 12345678G Receiving side remote unit Open Short Cross Idn G Ground shield layer Pass Split Rev t Idn The number of remote identification unit n 1 2 3 4 LANsmart Pro displays cable map results by pin to pin If there are shorts w
Download Pdf Manuals
Related Search