Operating instructions fpr OSRAM DALI Professional Controller
Contents
1. Analog DALI circuit A Ill 2010 13 Operation 14 DALI Professional Controller 4 Pushbutton Pushbutton State change SELECT ON OFF DIM 3 Press Only the DALIPORT C LEDs light up Only the EVGs connected to DALI circuit C can be operated with ON OFF DIM DALI circuit A Only the DALIPORT D LEDs light up Only the EVGs connected to DALI circuit D can be operated with ON OFF DIM 4 Press DALI circuit A RELAY K1 LED blinks rapidly Relay K1 has been selected and is operable 5 Press 1 Short press Relay K1 is audibly energised and the LED blinks slower RELAY K1 lights up Relay K1 is energised RELAY K2 LED blinks rapidly Relay K2 has been selected and is operable RELAY K1 lights up Relay K1 is energised RELAY K2 LED is off Relay K2 is still de energised RELAY K3 LED blinks rapidly Relay K3 has been selected and is operable RELAY K1 lights up Relay K1 is energised RELAY K2 and RELAY K3 LEDs are off K2 and K3 relays are still de energised RELAY K4 LED blinks rapidly Relay K4 has been selected and is operable 6 Press 7 Press 8 Press 1 Short press Relay K4 is audibly energised and the LED blinks slower 2 Short press Relay K4 is audibly energised and the LED blinks rapidly again 9 Press All four DALIPORT LEDs light up The RELAY K1 LED lights up because relay K1 is the only one in the switching state energised gt gt D2. EMC resistance 100 240 V AC 50 60 Hz DC operation permissible 25 W 0 C 40 C IP 20 0 5 2 5 mm fixed 0 5 1 5 mm flexible 4x 200 mA basically insulated 4 x 64 400 g 160 x 91 x 62 mm 9 HP IEC 62386 EN 60950 EN 55022 IEC EN 61000 C Conformity with the relevant EU directives is confirmed by the CE symbol Notes Address Circuit 18 Name Comments II 2010 Address Circuit Name Type Comments Address Circuit Name Type IIl 2010 DALI PRO Cont 4 ba1003en we1 01 indd OSRAM GmbH Kunden Service Center Customer Service Center CSC Steinerne Furt 62 86167 Augsburg Germany Tel 49 0 1803 677 200 kostenpflichtig charges apply Fax 49 0 1803 677 202 www osram com www osram de 4008321478948 ZNN 2603769 000 00 B Comments
3. Luminaire ON max yes IIl 2010 15 Operation DALI Professional Controller 4 Systems RESET With the systems RESET all connected devices can be reset to the factory default settings Press the ON OFF DIM pushbutton for 10 s to carry the systems RESET Operation e Switch luminaires via short press I O0 Ol Dl Di Dimming luminaires via long press Each repeated long press of the button causes a toggle between increased brightness and decreased brightness Further operating functions Further operating functions can be configured with the DALI Professional software see the separate software operating instructions Assignment of the pushbutton functions classified by short press long press and double press Free assignment of the pushbuttons and sensors to EVG groups also across all DALI circuits e Setting up scheduled activity procedures Offline mode power supply via the USB interface 16 The control unit can be operated in the Offline mode for special applications such as for a firmware update or the reading out of serial and version numbers for example The control unit is not supplied with mains voltage but instead via the USB inter face DALI circuits are not supplied with voltage The SELECT and ON OFF DIM pushbutton do not have a function Step Task Disconnect power supply gt POWER LED is switched off gt DALIPORT LEDs are switched off 2
4. The control unit is connected with the PC via the USB interface OFFLINE LED lights up continuously II 2010 DALI Professional Controller 4 Operation Behaviour after a power failure II 2010 In the Construction Site or Plug amp Play mode After voltage is restored to the control unit again with the pushbuttons the state that existed before the power failure is restored Relay states are retained EVGs call up the state that existed prior to power failure last level If the EVGs are still supplied with voltage from another power supply line these call up consequent to the lacking DALI communication until voltage restoration reaches the system failure level of 100 that is set at the factory With previous configuration by means of the DALI Professional software After voltage is restored to the control unit again the state that existed before the power failure is restored by means of the DALI Professional software Activity procedures taking place at the time of the power failure are not recontinued or restarted after voltage is restored 17 Appendix DALI Professional Controller 4 Technical data Operating voltage Max power consumption under full DALI load Working temperature Protection type Protection class Leads diameter DALI power supply Max number of DALI EVGs addressed Weight Dimensions L x W x H Applicable standards DALI standard Safety EMC emission
5. 2 Sensor couplers If more couplers are required the number of EVG in the DALI can be reduced A maxi mum of 64 DALI coupler addresses are available for each DALI circuit OSRAM DALI couplers can also be deployed across all circuits Pushbutton Standard commercial pushbuttons can be connected to the pushbutton couplers or via an e bus DALI gateway capacitive glass touch control elements and touch screens as well See separate operating instructions II 2010 DALI Professional Controller 4 Installation Connection diagram DALI PROFESSIONAL CONTROLLER 4 A B C K4 DA DA DA 66060066 06600000 66600000 D Analog wiring Lm m of the B C and D circuits A2 EI DALI ECG i l 4 DA i EES FE 1 Sensor Light and O e DALI Professional moon sensor Ri Sensor coupler 0000 DA DA DALI Professional Pushbutton coupler A B C D 00000000 DALI ECG A3 DALI ECG A DA DALI Professional Pushbutton coupler A B C D DALI ECG DALI ECG Ill 2010 11 DALI Professional Controller 4 Installation System overview Pushbutton coupler Light and motion sensor II 2010 12 DALI Professional Controller 4 Operation Basic state After initial connection to mains voltage the control unit is in its basic state Energised with mains voltage gt LED POWER blinks for approx 10 seconds and then lights up continuously DALI power supply is acti
6. C D B Relay contacts K1 K2 K3 K4 C USB interface type B for PC connection J Pushbutton e SELECT pushbutton E e ON OFF DIM pushbutton F IIl 2010 5 Description DALI Professional Controller 4 LED displays DALIPORT G Status of the DALI A B C D lines LED Meaning On Mains voltage present DALI power supply active Off No mains voltage present DALI power supply inactive control unit supplied only through USB Flashes Short circuit within the DALI circuit voltage 0 V Sparks Overvoltage in the DALI circuit voltage 20 V RELAY H Status of the relay outputs K1 K2 K3 K4 LED Meaning On Relay energised Off Relay de energised switching state as on imprint Flashes See Construction Site Mode in Operation LEDs for status display of the control unit K PLUG amp PLAY LED Meaning On Plug amp Play mode available i e control unit has not yet been configu red by means of PC Off Plug amp Play mode not available i e control unit has been configured by means of PC POWER LED Meaning On Mains voltage is present Control unit is operational Off No mains voltage present Flashes Startup phase approx 10 s after a power failure OFFLINE LED Meaning On No mains voltage present The control unit is not supplied with mains voltage but instead via the USB interface Offline mode power sup ply via the USB interface 6 I
7. D O O Q Q If no operations are performed for approx 30 seconds the control unit returns to its basic state Switching or dimming states are retained however and in the case of the relays are also displayed by the LEDs Note If the control unit has been configured by means of PC the changed switching or dimming states are retained for approx 30 seconds Afterward the state prior to manual operation is restored again the activity is comparable with the restoring of voltage after a power failure II 2010 DALI Professional Controller 4 Operation Plug amp Play mode Simple light controls with motion detection can be set up in the Plug amp Play mode by connecting DALI Professional pushbutton couplers and DALI Professional sensors The Plug amp Play mode is only available if the control unit has not yet been configured by means of PC and the PLUG amp PLAY LED is lit up Note Pushbutton and sensor switching operations only affect the DALI circuit to which the respective pushbutton coupler or sensor coupler is connected Light sensors do not have a function Symbols O gt I Switch on Q Luminaires on gt A SES LO Switch off Luminaires off p Tuba Pushbutton on d the luminaire Principle Luminaire OFF Pushbutton pressed yes yes Q Luminaire d 5 min ON max no no Pushbutton pressed Luminaires manually switched off before max 30 s yes yes no
8. DALI Professional Controller 4 Control unit Operating instructions PLUG amp PLAY DALI OSRAM A BC D EE DALIPORT Power PROFESSIONAL SCH RELAY 0 orrLine CONTROLLER 4 K1 K2 K3 KA L ERROR Wie preparin eu SELECT ON OFF DIM 705 259 e f 0 5 1 59 e e NE eo 10 12 mm 100 P 240V K1 K2 K3 B c NC N le er A Tui Iud Dd i EE ET ka Contents General instructions Safety instructions Klee n MEER RET Purpose and application Configuration Design Connections Pushbutton LED displays IAS CHE le Lu eT Fasten control unit Connecting the control unit Safety instructions Preparing the wiring Relays Number of pushbuttons and sensor couplers Pushbutton Connection diagram System overview ecce ET mM Basic state Construction Site mode Plug amp Play mode Further operating functions Offline mode power supply via the USB interface Behaviour after a power failure ADO RO TETTE T Technical data Applicable standards Notes gt O O1 O1 O1 O1 CI Safety DALI Professional Controller 4 General instructions The control unit must only be installed and put into operation by a qualified electrician The applicable safety regulations and accident prevention regulations must be ob served Safety instructions N WARNING Exposed live cables Danger of electric shock e Only work on the control unit when it is de en
9. ergised CAUTION Destruction of the control unit and other devices through incorrect mounting e The control unit should only be mounted in switch cabinets DIN 43880 e The DALI standard as per IEC 62386 must be complied with 4 II 2010 DALI Professional Controller 4 Description Purpose and application The DALI Professional control unit makes scene based operations and daylight pres ence dependent operations possible The control unit can control up to 256 4x64 DALI operating devices via 4 DALI lines and functions with any other device of the DALI Professional product family For more detailed information on DALI see http www dali ag org The gateway is designed for installation on 35 mm DIN rails in switch cabinets Configuration In order to make use of the control unit s full functionality e g brightness control scenes sequences colour control addressing you must have a PC configured with the DALI Professional software see the separate software instructions Simple light operations switching on off dimming can be carried out without previous configuration see Operation in these operating instructions With the pushbuttons directly on the device Construction Site mode With the buttons directly on the device and the motion sensors Plug amp Play Mode Design The control unit is made up of the following components Connections Power supply A DALI lines two pole A B
10. ing with a 5 core cable e g NYM 5 x 1 5 mm if necessary together with the mains voltage L N PE e Do not connect the DALI wiring with external voltage especially not with 230 V mains voltage Any potential overvoltage is only checked when starting up the DALI Professional CAUTION Destruction of the control unit and other devices through incorrect mounting e Connect relay contacts with max 5 A ohmic load e Connect an interference suppressed contactor in between for higher loads Using electronic ballast reduces the switching load with respect to ohmic loads at the same wattage Ill 2010 3 Installation 10 DALI Professional Controller 4 Preparing the wiring Wire stripping for connecting the relays DALI and mains cables to the plug in termi nals 10 12 mm 10 12mm Relays Depending on the connection the relays function as break contact make contact or make break contact Relays Connection to K1 K2 K3 K4 Break contact ES Make contact 7 gt Make break contact Ee Number of pushbuttons and sensor couplers If a 64 EVG is connected to a DALI circuit the maximum drive current available in this DALI circuit is 70 mA Specific power consumption of the couplers DALI Professional sensor coupler 5 mA DALI Professional pushbutton coupler 6 mA gt Connection examples of a DALI circuit 14 Sensor couplers 10 Pushbutton couplers and
11. ll 2010 DALI Professional Controller 4 Description ERROR LED Meaning On Lamp faults detected Off Normal operation SERVICE D LED Meaning On Off Reserved for future applications SX OSRAM BC D PLUG amp PLAY DALI B DALIPDRT Q Q O Q POWER PROFESSIONAL by OSRAM YOOOO Q OFFLINE CONTROLLER 4 K1 K2 K3 K4 ERROR wire preparation push in ES s 0 5 2 59 D Leo f 0 5 1 5 C 0 40 10 12 mm 100 A B DA D IIl 2010 7 Installation DALI Professional Controller 4 Fasten control unit The DALI Professional control unit is only intended to be mounted on 35 mm DIN rails in a switch cabinet as per DIN 43880 It requires an installation width of 9 horizontal pitch units HP Proceed as follows Step Task 1 Press in lock clips until you hear them lock with a click sound 2 Lock in the control unit on the DIN rail Removal Using a screwdriver push out the lock clips II 2010 DALI Professional Controller 4 Installation Connecting the control unit Safety instructions N WARNING Protection Class device Danger of electric shock e Securely connect the protective earth PE e Use B 10Aor B 16 A type unit as circuit breaker N WARNING The DALI interface is insulated by a basic insulation Danger of electric shock e Use wires that can handle power line voltages for the entire DALI wiring e Include DALI wir
12. ve gt LEDs DALIPORT lights up continuously Relays de energised gt LEDs RELAY have been switched off Plug amp Play mode available if the control unit has not yet been configured by PC gt LED PLUG amp PLAY lights up continuously Construction Site mode In the Construction Site mode the DALI circuits and relays can be energised individu ally by means of the SELECT and ON OFF DIM pushbuttons and the DALI circuits can also be dimmed Prerequisite mains voltage present Procedure example Pushbutton Pushbutton State change SELECT ON OFF DIM Basic state All four DALIPORT LEDs light up 1 Long press A DALI broadcast RESET is transmitted All connected EVGs and couplers are reset to their factory settings The entire system is in a defined state Only the DALIPORT A LEDs light up Only the EVGs connected to DALI circuit A can be operated with ON OFF DIM 1 Short press All EVGs connected to DALI circuit A are switched on to their maximum value 2 Short press All EVGs connected to DALI circuit A are switched off 1 Press 1 Long press All EVGs connected to DALI circuit A are dimmed 2 Long press Reversing the dimming direction Each repeated long press of the button causes a toggle between increased brightness and decreased bright ness Only the DALIPORT B LEDs light up Only the EVGs connected to DALI circuit B can be operated with ON OFF DIM 2 Press
Download Pdf Manuals
Related Search