HDfury 4 (aka 3Dfury) User Manual Rev 1.1
Contents
1. The HDfury4 perfectly centers the image automatically when Component and or Digital video output is used If RGB video output is needed some fine tuning of the image centering may be required The L R switch may be pushed up or down to shift the image until it is perfectly centered Hold the switch in either direction to shift the image faster To reset back to the default settings hold the switch in either direction for 15 20 seconds Note reset will revert all settings back to factory default The HDfury4 automatically saves the setting and will remember it the next time the resolution is used Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A bE party and or a custom firmware can be used HDfury 4 User Manual 3D Mode Button The HDfury 4 automatically switches to 3D mode if the correct information is sent from the source If for some reason the HDfury4 does not correctly switch to the correct mode the user can cycle though 3 modes via a push button that switches between 3D Side by side gt 3D Over Under gt 2D gt 3D Side by side force 3D Side by side mode force 3D Over Under mode back to 2D Automatic Please note that Output frame rate and scaling are based on DIPs 7 and 8 in the following way If DIP7 is ON then the output will be 720p120 720p is implied because 1080p120 does not ex2. A bE party and or a custom firmware can be used HDfury 4 User Manual Video EDID Video EDID can either be read from the sink device or forced to fixed full 3d HD EDID depending on DIP switch 9 setting For the Sony PS3 and some other devices you will need to redo the video settings if you change the position DIP switch 0 First change the Dip switch then unplug all cables from the HDfury4 including the USB power plug Wait 5 10 secs then reconnect all cables then set the video settings on the source To force video EDID to be read from the sink device set DIP switch 0 to OFF iJ 1234567890 To force video EDID to be set to the built on full 3d HD set DIP switch 0 to ON 1234567890 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A bE party and or a custom firmware can be used HDfury 4 User Manual Frequently Asked Questions FAQ 3D Can the HDfury4 be used for 3D Games Yes The HDfury4 supports the 3D frame packing standard used by 3D games as well as all other 3D formats Can the HDfury4 be used for 3D Blu ray movies Yes The HDfury4 supports the 3D frame packing standard used by 3D movies as well as all other 3D formats Can the HDfury4 be used for 3D satellite cable or 3D internet streaming content Yes The HDfury4 supports the 3D side by side and top and bottom standards as well a
3. blank when I play back Blu ray discs but not when play DVDs What s going on Blu ray discs are natively 1080p 24Hz You likely have your Blu ray player set to 24Hz or Automatic frame rate output so that it is outputting a 24 Hz fps signal Most displays that do not have HDMI inputs do not work at 24 Hz so you need to turn this off Either set your Blu ray player to 50 or 60Hz or set Automatic Frame Rate to off See your Blu ray player manual My Sony G90 CRT projector looks funny when I use the HDfury4 Go into the G90 service menu Input Setting with the fury installed and set the Clamp to HP or H C from auto This should straighten out the picture if it is varying in brightness and getting weird bands of dark as scenes change I can t get past 1080p on my PC while hooked up from my DVI port to the HDfury4 even when using PowerStrip Why not In order to go beyond the 165Mhz pixel clock barrier of 1080p 60 from your PC you will need a DUAL LINK DVI to HDMI cable That s the cable that has all the pins filled in on the DVI end and had an HDMI plug on the other Image Shifting Will the HDfury4 shift the image to the left or cropped cut off in any way like some other converters No The HDfury4 includes advanced features to ensure that the image stays perfectly centered when component Y Pb Pr output mode is used The HDfury4 also adds a new feature to allow for manual centering of the image when RGB output mode is used Do
4. found on the back of the HDfury4 and set DIP switch 1 to OFF Make sure to use the HDfury4 component breakout cable to connect the HDfury4 to your display s component Y Pb Pr input Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual want to use the RGB VGA input on my display How do I set the HDfury4 to output RGB VGA video Lift the little panel found on the back of the HDfury4 and set DIP switch 1 to ON Make sure to use one of HDfury4 RGB cables to connect the HDfury4 to your display s RGB VGA input Three RGB cables are available A VGA D Sub15 cable a 5 BNC cable and a special Barco CRT projector port 3 cable Do not use the component 3 RCA phono style connector cable shown above as it will not work Does the HDfury4 support 24fps found in next generation Blu ray and HD DVD players Yes The HDfury4 supports 24fps With cathodic displays such as CRT projectors or CRT based RPTVs or tube TVs 24fps is too low of a frequency for the display to use The image will flicker like crazy and will not be watchable You can framerate convert 24fps sources to 72hz when using a CRT based display which will result in a great flicker free picture You can use 24fps on a plasma or LCD display and it will be displayed nicely using the HDfury4 can only get
5. is enabled by default some people may choose to disable this feature and do their image shifting in the display or in a video processor instead To turn off the L R image shifting feature lift the little panel found on the back of the HDfury4 and set DIP switch 5 to OFF used the L R image shifting push button and now I don t have an image anymore You have shifted the image too far resulting in a loss of sync on the display Hold the shift push button in either direction for approximately 15 seconds and the image will reset to the default center value Then re adjust slowly carefully Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A ge party and or a custom firmware can be used HDfury 4 User Manual RGB Image Sync My display has composite combined sync with only 4 BNC connectors not 5 Examples Barco 7xx Cine7 or Ampro CRT projectors What cable do I order How do I hook it up Order the GREEN 5 BNC breakout cable and combine the H V sync lines using a 2 BNC T connector or You could also use an Extron 109 or 202 box to combine the two sync lines The image rolls is unstable or doesn t always lock on What do do Some displays such as early Electrohome ECP and Barco CRT projectors have fussy sync circuitry You need to combine the H V sync lines using a 2 BNC T connector see picture in last question You coul
6. lower resolutions to work When I set my source to high resolutions like 1080p don t get an image 1 Make sure to use the included HDfury4 power supply at all times It is required at all times 2 Many TVs do not support 1080p and must be fed a 1080i or 720p signal instead Make sure to set your source to 1080i or 720p unless your display s manual specifically states that it supports 1080p 3 Make sure to turn off 24fps 24p support in the source see last question The picture is blank don t get an image at all from my PS3 Blu ray player or other source 1 Make sure your display supports the resolution the source is feeding it If your TV does not support 1080p set your sources to 1080i or 720p Some sources will automatically use the highest resolution available to them based on what they see connected and since they see the HDfury4 as 1080p FULL HD the source will think you have a 1080p capable TV and is most likely feeding the HDfury4 a 1080p signal You need to lower this to 1080i or 720p in the source device 2 Make sure that the 24fps output option in the source device is set to OFF or DISABLED and not AUTOMATIC unless your TV specifically supports 24fps Most do not especially older TVs that do not have HDMI inputs 3 Make sure you re using the HDfury4 power supply at all times I m still getting a black screen from my PS3 when using the HDfury4 How can fix this The problem is that you likely connected the H
7. 080p 72Hz All standard definition SD and high definition HD resolutions are supported in component Y Pb Pr and HDMI output mode including 1080p 60 and 1080p 24 Does the HDfury4 change the resolution Up convert or down covert The HDfury4 does not change the resolution in anyway in 2d mode It can framerate convert film based sources up to 72hz in 1080p mode The HDfury4 outputs whatever resolution you feed it Feed 1080p in and you ll get 1080p out Feed 480i in and you ll get 480i out In 3d mode the 3d signal is converted into 720p or passed though as 1080p depending on the position of dip switch 8 The frame rate will be output at 60Hz if the high frame rate switch is off or up to 144hz if it is set to on Does the HDfury4 support both Component and RGB video output thought they were the same The HDfury4 supports both component Y Pb Pr or YUV and RGBHV sometimes called VGA signal types on the output They are not the same at all and cannot be used interchangeably Some displays have component inputs some displays have RGB some have both The HDfury4 lets you choose between the two to best match your display s requirements My picture is all green What s going on You likely have a display that only accepts RGB and you have the HDfury4 set to component output Y Pb Pr Switch it to RGB want to use the component input on my display How do I set the HDfury4 to output component Y Pb Pr video Lift the little panel
8. 0Hz 1280 x 720 Frame packed 720p 60Hz 1280 x 720 Frame packed 1080p 24Hz 1920 x 1080 Frame packed 1080p 25Hz 1920 x 1080 Frame packed 1080p 30Hz 1920 x 1080 e 3D OUTPUT O O O 720p60 720p72 720p96 720p120 720p144 Frame Sequential 720p and or 1080p for 60hz display 1080p60 1080p72 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual Specifications Features Input 1 x HDMI v1 4 DVI 1 0 compatible 12 bit deep color HDMI native support Output Digital HDMI DVI D and or VGA FEMALE output connector 10 bit analog resolution HDCP supported Integrated HDCP decipher engine Pre programmed HDCP key Horizontal shift capability for RGB output mode o Enabled with a dip switch applied with push buttons Output horizontal and vertical sync polarity selector for RGB modes dip switch Digital Output format Either HDMI or DVI D Analog Output format Either RGB or YPbPr dip switch selectable o YPbPr requires VGA gt 3RCA breakout cable All HD SDTV formats from 1080p down to 480i NTSC and PAL o Including 1080p 72Hz PAL and NTSC for RGB output only o Including 1080p 24Hz PAL and NTSC 11 bit 225MHz DAC processing for true 10 bit analog output Two separate Internal EDID EEPROM with complete CEA861 extension block Dip switch selectable o
9. 20p72 720p96 720p120 720p144 Frame Sequential m 720p and or 1080p for 60Hz display m 1080p60 1080p72 How do I know if my display supports 50 60Hz or 100 120Hz All displays support 50 60Hz Some displays support 100 120Hz Try both My HD display is from Europe UK Australia where we use a 50Hz refresh rate Will it work Yes as all HD displays that support 50Hz also support 60Hz What happens when I watch regular 2D content The HDfury4 simply passes the 2D video signal through unaltered except in double triple frame mode where it can output 1080p48 and 1080p72 from 24hz material It s as if the HDfury4 is not even there The 2D video signal is not altered in anyway The HDfury4 supports all standard 2D video resolutions including but not limited to NTSC 480i p PAL 576i p HDTV 720p 1080i 1080p use an HDMI converter with my display Will the HDfury4 work with a HDMI converter Yes Here s a sample hookup PS3 gt HDMI cable gt HDfury4 gt HDMI cable gt HDMI converter gt Display However the HDfury4 also includes its own converter so you most likely will not need any additional converter for analog output The HDfury4 can output both Analog and Digital video audio signal simultaneously What version of HDMI does the HDfury4 work with Do I need HDMI 1 3 1 4a Does it matter It does not matter TheHDfury4 works with any version of HDMI from 1 0 and up That said if you find you re having problems it s best t
10. 24hz content into 1080p 48hz and 72hz It also allows 3D to be output at 720p 60hz 72hz 96hz 120hz and 144hz If used in a dual projector setup it allows both the left and right streams to be output at 1080p 24hz 48hz 60hz and 72hz Please note that this is a multipurpose button Operation depends on the current mode AND DIP7 If DIP7 is ON high frame rates are enabled For 3D movies framepack 1080p24 pressing down switches between 720p60 72 96 120 144 1080p72 720p60 For 3D movies framepack 1080p24 output as LEFT RIGHT for dual projectors 1080p24 gt 48 gt 72 gt 24 For 2D movies 1080p24 1080p24 gt 48 gt 72 gt 24 If DIP7 is OFF high frame rates are disabled All movie outputs at 60Hz either 1080p DIP8 OFF or 720p DIP8 ON Other modes no effect All modes stored and read back upon power up Also all RGB shift values are stored individually for every resolution mode separately Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A be party and or a custom firmware can be used HDfury 4 User Manual DIP Switch Settings To customize your HDfury4 a bank of ten 10 DIP switches are provided Remove the small cover on the back of the HDfury4 to access the DIP switches A Open to Access DIP SWITCH Panel O6GBZSSPESL es LTT MA010G 1 A0D YOUMS JIG OY uodo 4 sumos ymezog L Ke GiG3 2
11. 80p signal from HDMI sources Prior to exchanging video data the HDMI source exchanges HDCP keys with HDMI display Both devices have a special HDCP chip embedded If your display doesn t include an HDCP chip even if it s technically able to display 720p or 1080p signal it will display a BLACK SCREEN On some devices ex Playstation3 Xbox360 1080p mode is only available through the HDMI output use component cables to connect my Blu ray or DVD player to my display device and it works just fine Why do I need HDfury4 Blu ray and many DVD players can also up convert standard definition DVDs to higher resolutions 720p 1080i 1080p but they only do this via the HDMI outputs not component So if you want to get the higher resolution benefits of your player s upconversion circuitry you re forced to use HDMI As well in the future it may not be possible to pass certain high definition content over component video cables A content flag called the ICT Image Constraint Token allows broadcasters and movie studios to limit or down res the HD video signal to standard definition 480P resolution over component video cables Hollywood has reportedly agreed to not activate this flag until 2011 2012 And the most important reason to use HDfury4 The picture quality is substantially better Sharper cleaner less noise less ringing etc Sound Do I need to use the sound output on the HDfury4 Likely not The audio output of the HDfury4 is a conv
12. DIP 9 OFF Component output ON Sync passed OFF Sync not forced positive passthrough ON RGB color depth 0 255 DIP 5 DIP 6 DIP 7 DIP 8 OFF RGB shift disabled ON Power LED ON OFF High Framerate off OFF 3d scaling 1080p OFF Read audio info from sink device DIP 0 OFF Read video info from sink device These settings are explained in the sections that follow Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual RGB VGA RGBHV Output or YUV COMPONENT YPbPr Output RGB VGA RGBHV Output If your Display accepts only RGB VGA or RGBHV set the Dip Switch 1 to ON ON 1234567890 YUV COMPONENT YPbPr Output If your Display accepts only YUV COMPONENT or YPbPr set the Dip Switch 1 to OFF 1234567890 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A bE party and or a custom firmware can be used HDfury 4 User Manual RGB Sync When the HDfury4 is set to RGB output mode the sync signals may be passed through as is forced positive forced negative or inverted Check your owner s manual to see if your RGB display has any special sync requirements RGB sync is not used when the HDfury4 is set
13. Dea AEE E E E S 21 EE a E E A TE A TE TA TT 26 DVI Mode for use with Capture Cards and SDI Converters cccccccssseeees 26 Generalen enn n as oocensninan np eleipind ata E A A a 26 SOUNA hes detec ansehen AE E E E EE EE E E 26 ITS accel EA AA E AEE 28 NS Oi reee E E teins O A O E S 28 Image Shifting esiri ensein eE EE ER ETE ETER 31 RGB Image SYNC siradeesi cccececsvasttuse n e i a aa a a aia 32 Colour Depth Upscaling sseesssennenneeerrerrrsrrrssrrssrrrerrrerrrrrrrerreerrrennssnnsnesssnsssna 31 POWE orosei enaa a es aa aad eid at end ans ep et E nies eee E EREKE REESE 33 MiscelaneGUS rnaitee ees e e E A E E A E T e 34 SC IIC A NUAS pig ssascactencetewacsartnepnssncnhncaiessonictnawaaiiactosontaareaarorinieudiaetusenraumen 35 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A El party and or a custom firmware can be used HDfury 4 User Manual Overview The HDfury team would like to thank you personally for purchasing the HDfury4 This unique HDMI converter will allow you to connect 2D 3D HDMI devices to any TV Monitor and Projector either through Component RGBHV DVI D or HDMI It can output both Digital and Analog Video Audio simultaneously It can also double or triple frame rate convert 1080p24 material up to 1080p72 giving a film like picture with no flicker The HDfury4 is the world s most powerful and a
14. Dfury4 to the HDMI port while the PS3 was still setup to output by another port component or composite The result is no picture over HDMI The PS3 will output low resolution on every output when you reset the display settings this way PS3 in stand by mode hold on power for 5 sec until you heard 3 beeps The PS3 restarts and you can than access low resolution through both HDMI and or other ports and perform the display test to choose your preferred resolution Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual On my PS3 I can see the menu play games and Blu ray discs but I get a blank screen or an out of range error message when play a DVD You need to change a setting in your PS3 In addition to setting up the HDMI resolution on the PS3 as outlined above you also have to go under the Blu ray playback settings and adjust the DVD upscale feature because by default it will also be 1080p Another hint When you first connect an HDfury device to the PS3 the PS3 will ask A new HDMI device has been detected do you want to use it Answer YES only if your TV is 1080p capable Otherwise answer NO and you will be presented with another screen where you will be able to change the resolution settings and set them manually to whatever your TV supports My picture is
15. HDfury 4 aka 3Dfury User Manual Rev 1 1 HDfury 4 User Manual Table of Contents Table of contents aes seacoast cv sees eee sa tele 2 MVCN irere nentet Ra earreotea aaar ee aTa SENAN NaRa 3 Connecting Cables nnnnnnnnnnenneeneerensrnssrssssssssssnsnrrenrenrennnsnnsssssssnnsensssnss 4 Power Status LED ass sicsscinxinthvsvesavekesinrinstestenrnctonsocesehuniees ohietdceincohlstdenneantatenwetend 5 RGB Shift Image Centering cccccccesssssseecceceeeesecsssesneeeeceeeeesssssneeeeeess 6 3D Mode BN OI osetia aden enictsaenvescd cerdavancdsateseeepaguennonmianbeeconenendeeeaseoads 7 Stream Select BULL ON 6 sys sssisnecscsersd civ eoainsavcrvvrsanvarsarornar enamesneaneeerneneeonier 8 Frame Rate BUCO iy oy scscicnicss ice i vpuensidan cnidvanvnivanuuptouenanersasqasonbnd anivinGdanuiutaedaienvasidanse 9 Dip SWICK SETUINGS ccnauncasinenitenuninceniiei eminem 10 RGB Component Output sopigeiaacissiactvintvnssosdesmetateedovassanttatasinnesssuadeeddnemesivesedantes 12 RGB SYNC sviec seanseo ceded niana inaa ac coins Rained EE AE ne pune ade ee eee 13 Enchanced Colour Output cov snsenasnsvatonseansnasundninddeuslendevinniedntadistondioei inuabiadentiines 14 RGB SAFE eeaeee a E A E E EN E E 15 Power Status VED oresoon E N R E A 16 Hien Frame Rater Ton e E E ARE 17 SD SCANNE eraa e EE E E E E 18 Audio EDID eee e e E E E E E EE E E E E ES 19 Video EDID nisnin nn ame ene E TO EEE ee 20 Frequently Asked Questions FAQ
16. One EDID supports all formats o The other EDID is up to 1080i and no 24Hz support by default reprogrammable Automatic Input Format Detection Digital YCbCr and RGB Full BTB and WTW support in YPbPb output Automatically switches color spaces for both HDTV and SDTV Precise black levels no black crush in any standard mode Dual purpose audio output connector Oo SPDIF digital output for 5 1 Dolby DTS o Analog L R 2 channel stereo Industry Standard Compliance o HDMI 1 4 o EIA CEA 861E o DVI1 0 o HDCP 1 1 Digital Video Input Output o Dual integrated HDMI 1 4 cores Oo Supports DTV resolutions up to 1080p 72Hz or 720p 1080i 120Hz with 36 bit color depth o Flexible digital video interface 24 30 36 bit RGB YCbCr 4 4 4 16 20 24 bit YCbCr 4 2 2 8 10 12 bit YCbCr 4 2 2 ITU R BT 656 Integrated RGB Color Space Converter for both RGB to YCbCr and YCbCr to RGB both 601 and 709 with true 12 bit accurate data using 14 bit processing 4 2 2 lt gt 4 4 4 converter with 12 bit accurate data using 14 bit processing Digital Audio Output o HDMI audio pass through o Industry standard S PDIF output O Supports 2 channel 32 192kHz stereo audio O Supports IEC60958 2 channel PCM o Capable of passing IEC61937 compressed audio 5 1 Dolby Digital DTS etc o 7 1 Dolby True HD amp DTS Master Audio Optional Accessories o DLP Link 3D Glasses for DLP 3D Ready 120hz Projectors TV s o External 60 120hz 3D Glasses with emitter for a
17. able glasses that allow you define duty cycle delay offset invert sync presets etc How can know if my digital display will have a frame locking issue There s unfortunately no easy way to tell unless you talk to other owners of the same display or try it for yourself There s no comprehensive list of which digital displays suffer from it see last question The good news is that it s extremely rare With hundreds of units in the field there have been very few complaints Some displays can be fixed by making display setting changes ex switching to game mode which will drop unnecessary processing from the display as is required for the content to sync properly However the HDfury4 glasses and emitter are fully customizable glasses that allow you define duty cycle delay offset invert sync presets etc Is there any way to use the HDfury4 with passive glasses glasses without batteries No Active shutter glasses are required that are sync ed to the HDfury4 Except for Dual projectors setup where passive glasses are required have active shutter glasses that came with my TV but the emitter is built into my TV Is there an way to use these glasses with HDfury4 No An emitter that plugs into the HDfury4 is required so that the glasses can be kept in sync with the image Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will
18. be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual The HDfury4 glasses and emitter are fully customizable glasses that allow you define duty_cycle delay offset invert sync presets etc Can use third party glasses that include an emitter Yes Any external 3rd party glasses that include an emitter will work with the HDfury4 as long as the emitter has the 3 pin standard mini din connector Does DLP glasses work with HDfury4 Yes As long as the projector supports dlp link to drive the glasses How are the new lossless audio formats via HDMI input handled E g DTS HD MA and DD E AC3 Are they stripped down to DTS core or Dolby Digital respectively to fit the requirements of the S PDIF standard Lossless audio is transmitted through HDMI output only The HDfury4 does not compress or otherwise down convert the incoming audio Only stereo PCM and 5 1 sound can be output via SPDIF and analog audio output Does the HDfury4 allow you to extract the sync for 3D glasses out of digital HDMI DVI 100 120Hz signal not a super frame not a side by side signal Can the HDfury4 provide the sync signal for attached 3D glasses when its feed with a digital HDMI DVI 100 120 Hz signal If yes can it be fed with any resolution and refresh rate within its bandwidth capabilities Yes the HDfury4 have an option to output sync for any content The HDfury4 synchronizes to the vertical sync signal and creates
19. convert all resolutions up to and including FULL HD 1080p For 3d it is shipped to output 720 60hz In most cases no further adjustments are required For displays with RGB VGA inputs or special requirements please see the DIP Switch Settings section further below to customize your HDfury4 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A bE party and or a custom firmware can be used HDfury 4 User Manual Power Status LED The HDfury4 logo will glow blue when in use When the HDfury4 first receives an HDMI signal the logo will quickly turn on then off and then on permanently to indicate that the 4 letters handshake has been completed The status of the blue logo may be used for troubleshooting Logo OFF Insufficient power Use the HDfury4 power supply Logo BLINKING on for split second off for 5 seconds The HDfury4 is receiving power and is ready to accept an HDMI signal Logo ON The HDfury4 is powered and receiving and decoding the HDMI signal Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used DI HDrfury 4 User Manual RGB Shift Image Centering in RGB mode H Shift Image Center Move to the Left No change Default position Move to the Right
20. cture blanking the problem is with the component cable RGB cable or the display Lift the little panel found on the back of the HDfury4 and make sure that DIP switch 6 is set to ON DIP switch 6 is used to turn the blue LED on off make sure it is set to ON if you are experiencing problems with your HDfury4 The blue LED will never come on if you have DIP switch 6 set to off Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual Miscellaneous The blue LED power light on the HDfury4 is too bright in my light controlled Home Theater Can I turn it off The easiest way to turn off the blue LED power light on the HDfury4 is to simply place a piece of tape over it Quick and simple However if you would like to deactivate it here s how Lift the little panel found on the back of the HDfury4 and turn DIP switch 6 to OFF To re enable the blue LED power light turn DIP switch 6 to ON Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A be party and or a custom firmware can be used HDfury 4 User Manual Highlight Features Main features e Add HDMI 2D and 3D to ANY TV Monitor Proj even 60hz TV e Display HDMI 2D and 3D content on Digital and or Analog disp
21. d also use an Extron 109 or 202 box to combine the two sync lines My display requires the RGB signal to always include negative or positive sync to work How do I set this The HDfury4 allows you to force the output sync to either positive or negative or invert it Previous HDfury models did not alter the sync signal in any way requiring extra hardware if your display has special sync requirements To set sync lift the little panel found on the back of the HDfury4 and set DIP switches 2 and 3 as follows Always invert sync Set DIP switch 2 to OFF DIP switch 3 to OFF Always positive high sync Set DIP switch 2 to ON DIP switch 3 to ON Always negative low sync Set DIP switch 2 to OFF DIP switch 3 to ON Always pass sync through as is Set DIP switch 2 to ON DIP switch 3 to OFF How do the two sync DIP switches work For those people who want all the details the two sync DIP switches control RGB image sync as follows DIP switch 2 ON Sync Passed OFF Sync inverted operates after DIP3 selection so it is possible to invert a forced sync too DIP switch 3 ON Force sync positive high OFF Sync not forced simply passed Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual Colour Depth Upscaling Can I turn the colour depth upscaling feature of
22. dio output in one connector located on the bottom of the unit labeled D A along with a headphone symbol It s a 2 in 1 connector meaning that you can plug in either a 3 5mm stereo analog jack or a digital mini TOLINK 3 5mm mini jack cable and get stereo analog sound or 5 1 Dolby DTS digital sound out of the HDfury4 See further below for pictures of both types of connectors cables HDfury4 3 5mm mini TOSLINK digital audio cable u If you d like to use a regular TOSLINK cable use a 3 5mm Mini TOSLINK to regular TOSLINK adapter A 3 5mm stereo audio cable can be used for connecting the HDfury4 to a TV if you do not have a home theater setup you only have 2 speakers in your TV Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A bE party and or a custom firmware can be used HDfury 4 User Manual Inputs How many inputs does the HDfury 4 have It has a single 3D HDMI 1 4 compliant with HDCP with support for Deep Color TM The HDfury 4 is the first product we offered that can convert 3d to work with any tv and also offers a hdmi output for both sound and video It passes though all colour spaces and is fully compatible with all HDMI audio formats Video What resolutions does the HDfury4 support The HDfury4 supports any resolution refresh rate combination interlaced or progressive up to 1
23. dvanced 2D and 3D converter ever built It includes advanced features such as HDMI 1 4 input with Deep Color support Supports and passes though RGB 4 2 2 and 4 4 4 Colourspaces Supports and passes though all lossy and lossless hdmi audio types Perfect image centering in both Component and RGB modes 3D mode output up to 720p144 Gamer mode 720p60 double frame into 720p120 User Upgradeable USB firmware and custom options via DIP switches Dual projectors setup using two HDfury4 modules and passive glasses Up to 720p240 in dual projectors setup A A A Component RGB Optionnal Output RGB Image I Centering Centering ia Supply o USB Upgrade Digital Video Digital Video Audio HDMI Output iR HDMI Input Output Vv Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A bE party and or a custom firmware can be used DI HDfury 4 User Manual Connecting Cables Breakout Cable VGA RGBHV or YPbPr to Display VGA Connector 5V 2000 mA Power Connector Audio Optical or Analog Output option To use your HDfury4 e Connect a HDMI input cable to the HDMI input e Connect a video output cable to the analog video output or HDMI output e Connect the HDfury4 power supply e Connect an audio output cable optional As shipped the HDfury4 defaults to Component Y Pb Pr video output and will
24. enience feature if you do not have a home theater receiver The HDfury4 supports stereo analog output as well as 5 1 Dolby DTS digital SPDIF output If all you have are the speakers in your TV you can use the 2 channel analog audio output of the HDfury4 as a convenient way to feed audio directly into your TV without having to run separate possibly long audio cables from the source to your TV as in many setups the HDfury4 will be plugged right into the TV This way you only need to run one HDMI cable to the TV and then use a short audio cable from the HDfury4 to the TV sound input Anyone with a home theater receiver preamp and separate speakers should instead connect their source devices directly to the receiver pre amp and not use the HDfury4 sound output You may use the 5 1Dolby DTS digital audio output of course if the positioning of your Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual HDfury4 makes this more convenient The choice is up to you Typically there is no need to use the audio features of the HDfury4 with a home theater setup The HDfury 4 will also pass though the audio from the source over HDMI or can be forced to 2 channel PCM stereo over HDMI as well How do I hook up the audio from the HDfury4 The HDfury4 has both analog and digital TOSLINK au
25. er In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual Input Output mode HDfury4 Input Output mode e 2D VIDEO MODE COMPATIBILITY O NTSC 480i p PAL 576i p HDTV 720p 1080i 1080p e 2D OUTPUT O O O 2D movies 1080p24 1080p48 1080p72 HDfury4 can double and triple frame from 24hz material 720p60 720p120 Pass through any resolution e 3D MODES INPUT COMPATIBILITY O Or E e E OF E E t E E Ov Or E E OF E E Or O Or Ov O O E e O O e O gt O Full 3D HD 1080 per HDMI Blu ray 1920 x 2205 24Hz Full 3D HD 720 per HDMI Blu ray 1280 x 1470 60Hz Top Bottom 1080p 24Hz 1920 x 1080 Top Bottom 1080p 25Hz 1920 x 1080 Top Bottom 1080p 30Hz 1920 x 1080 Top Bottom 1080p 50Hz 1920 x 1080 Top Bottom 1080p 60Hz 1920 x 1080 Top Bottom 1080i 50Hz 1920 x 1080 Top Bottom 1080i 60Hz 1920 x 1080 Top Bottom 720p 30Hz 1280 x 720 Top Bottom 720p 50Hz 1280 x 720 Top Bottom 720p 60Hz 1280 x 720 Side by Side 1080p 24Hz 1920 x 1080 Side by Side 1080p 30Hz 1920 x 1080 Side by Side 1080p 50Hz 1920 x 1080 Side by Side 1080p 60Hz 1920 x 1080 Side by Side 1080i 50Hz 1920 x 1080 Side by Side 1080i 60Hz 1920 x 1080 Side by Side 720p 50Hz 1280 x 720 Side by Side 720p 60Hz 1280 x 720 Frame packed 720p 30Hz 1280 x 720 Frame packed 720p 5
26. es the HDfury4 automatically center the image In component Y Pb Pr output mode the HDfury4 always automatically centers the image Nothing else needs to be done In RGB VGA output mode the L R image shift control on the side of the HDfury4 may be used to manually center the image after turning DIP switch number 5 to ON Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ed party and or a custom firmware can be used HDfury 4 User Manual The picture is not centered when I use the HDfury4 in RGB VGA output mode How do fix it Open the DIP switch cover and turn DIP number 5 to ON Then use the L R momentary contact switch on the side of the HDfury4 to shift the image left or right until it is centered This only needs to be done when you use a new resolution for the first time The HDfury4 will then remember the setting for that resolution for the next time you use it The theoretical correct RGB center values are already programmed into the HDfury4 so in many cases no shifting will be required but testing has shown that some TVs do need a slight adjustment The L R image shift doesn t work Make sure the HDfury4 is set to RGB output mode set DIP switch 1 to ON and that the L R image shift feature is enabled set DIP switch 5 to ON Can I disable the L R image shift feature Yes While the L R image shifting in RGB mode
27. f Yes Like the HDfury2 the HDfury4 expands the regular 16 235 image range to 0 255 for greater contrast ratio Some people may want to turn off this feature To turn colour depth upscaling off lift the little panel found on the back of the HDfury4 and set DIP switch 4 to OFF Power Do I need to use the HDfury4 power supply Yes Due to the advanced features the HDfury4 draws more power than previous HDfury models The HDfury4 power supply must be used at all times Is the HDfury4 power supply the same as that used by the HDfury1 HDfury2 and GammaX No The power supply for the HDfury1 HDfury2 and Gammax kits are 0 5A max current The HDfury3 is 1A max current The HDfury4 power supply can supply up to 2 0A Do not use an HDfury1 HDfury2 or GammaxX power supplies with the HDfury4 What sort of power supply does the HDfury4 use The HDfury4 power supply adheres to these requirements Provides REGULATED 5 5VDC power with 2 0A min DC current Delivers the power through a mini usb connector Trying to use an AC DC adaptor that doesn t adhere to these three requirements may destroy the HDfury4 Do not use the power supply from the HDfury1 HDfury2 or GammaxX with the HDfury4 My picture blanks out from time to time when using the HDfury4 Why is this happening If the HDfury4 blue LED is OFF during the picture blanking the problem is with the HDfury4 or the power supply If the HDfury4 blue LED is ON during the pi
28. ist If DIP7 is OFF then the output is 60Hz and either 1080p DIP8 OFF or 720p DIP8 ON If LEFT RIGHT Dual Projector is selected then resolution and frame rate follows the same logic so you can have dual projectors beaming 720p120 each for 720p240 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A be party and or a custom firmware can be used Sup tury 4 User Manual Stream Select Button Dual Projector Setup Left Frame Only Normal Default Right Frame Only A single HDfury4 set to left or right frame is able to convert 3D content into 2D in case you would like to watch 3D only content in 2D If you wish to use the HDfury4 in a dual 2D 3D projector setup or wish to convert 3D or PS3 SimulView into just the left or right stream you will need two HDfury4 s One set for Left stream and one set for Right stream By default they come shipped with the button in the center position for single projector use Please see above picture to aid in setting the HDfury 4 correctly for dual projector setup Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A 34 party and or a custom firmware can be used ESC tury 4 User Manual Frame Rate Button The HDfury4 comes with a unique feature that will convert film based
29. lay e HDfury4 can output in both Digital and Analog Video Audio simultaneously Therefor acting as an advanced digital analog splitter e Double and Triple frame 1080p24 material up to 1080p72 e 3D mode output up to 720p144 e Dual projectors setup using two HDfury4 modules and passive glasses e Upto 720p240 in dual projectors setup e 7 1 Dolby True HD amp DTS Master Audio e Input HDMI 1 4 HDCP compliant input with 3D and Deep Color support e Output Digital HDMI DVI D and or Component YPbPr YCbCr and VGA RGBHV video output e All modes auto detected if possible otherwise can be forced via button e 3 pin mini DIN Sync Out for optional emitter e Dynamically create EDID based on Sink EDID parameters e Customization settings available through DIP SWITCH and buttons e Perfectly and automatically center image in all standard NTSC PAL component modes e Manually adjust horizontal screen position in all NTSC PAL RGBHV modes e Performs Color Depth Up scaling in all modes ON OFF user selectable e Horizontal and Vertical Sync Polarity Inverter included e Automatic SD HD color space selection e Accept third party accessories on its output e Improved output cable driver for driving long cable runs 40 50 e Software Firmware upgradeable through USB e Sound output o Analog and Digital Optical S PDIF 5 1 Dolby DTS through an innovative 3 5mm combo jack and 7 1 DTS MA amp Dolby True HD via HDMI output o HDMI audio pass through Disclaim
30. ll other displays ie 60Hz non 3D Ready Projectors or TV s o Passive glasses for Dual projectors setup o HDfury4 Glasses with emitter 60 144hz All controls like Duty cycle Delay Invert Presets are on the glasses itself you can stay on the couch and tune up everything till perfection Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual Team HDfury thanks you for your support For help visit http www HDfury com Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A be party and or a custom firmware can be used
31. n receiving content that has HDCP encryption there will be no video output A be party and or a custom firmware can be used HDfury 4 User Manual 3D Scaling 3D sources are either scaled to 720p or 1080p depending on the position of DIP switch 8 To set 3D output to 1080p set DIP switch 8 to OFF Hi 1234567890 To set 3D output to 720p set DIP switch 8 to ON 1234567890 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A be party and or a custom firmware can be used HDfury 4 User Manual Audio EDID Audio EDID can either be read from the sink device or forced to 2 channel stereo PCM depending on DIP switch 9 setting For the Sony PS3 and some other devices you will need to redo the audio settings if you change the position DIP switch 9 First change the Dip switch then unplug all cables from the HDfury4 including the USB power plug Wait 5 10 secs then reconnect all cables then set the PS3 audio settings to automatic For other devices you may have to manually select supported audio To force 2 channel PCM audio set DIP switch 9 to OFF MW 1234567890 To force audio info to be read from the sink device set DIP switch 9 to ON 1234567890 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output
32. o hook up the 3D source directly to HDfury4 first then add additional equipment Some older HDMI receivers or switchers may block 3D recognition causing problems while others may work fine Do I need to set anything special in my 3D source device for this to work No The HDfury4 always outputs 3D content at 720p 60 720p72 720p96 720p 120 720p144 or 1080p24 1080p48 1080p60 1080p72 This is to maximize compatibility throughout all displays in the market There is no need to set the 3D source to any specific resolution the HDfury4 will take care of it and scale if needed Is there any latency delay introduced to the signal Less than one frame of latency per second is added to the signal which is not noticeable at all What is the USB port for To power the HDfury4 from any USB port such as a PS3 or Xbox 360 USB port and for firmware upgrades when new additional functions and enhancements are offered Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual What about long HDMI cable runs Can expect issues The HDfury4 acts as an HDMI repeater device So having a HDfury4 in the path will amplify and recover the signal You should not need any passive or active HDMI amplifiers especially if you put HDfury4 in the middle of your cable run If you previo
33. osting or flicker Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual SimulView Do the HDfury4 supports the PS3 exclusive SimulView mode Yes the HDfury4 fully supports SimulView mode This allows gamers to play SimulView supported multiplayer games giving each player their own full screen all on a single display What is required for SimulView to function on single display or projector You will need the PS3 compatible SimulView game HDFury4 emitter and two pairs of our RF glasses With this setup both players will have their own full screen view without seeing what the other players sees What is required for SimulView to function on an advanced dual screen setup You will need the PS3 compatible SimulView game 1 4 certified HDMI splitter at least 1 input and 2 outputs two displays or projectors and two HDfury4 s To hook this up you connect the HDMI splitter to the PS3 HDMI output and the outputs from the HDMI splitter to the 2 HDfury4 s Then the output from the two HDFurys would go to the two displays or projectors One Hdfury 4 needs to be set for left stream and the other for right stream output please refer to Stream Control section for additional details With this setup both players will have their own full screen with
34. out the need of wearing any glasses DVI D Mode for Use with Capture Cards and SDI Converters To use the HDfury 4 with a PC capture card or SDI converter you will need the Dr HDMI as well as the HDfury 4 The Dr HDMI with a DVI D bin EDID file loaded on it is needed to trick the HDfury 4 into DVI D mode instead of HDMI mode You will also need to run separate audio to the PC capture card or SDI converter as DVI D does not support audio DVI D uses the same pinout as HDMI but it does not include audio output Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual General Why do I need HD 720p or Full HD 1080p Blu ray players HDMI graphic cards PS3 Xbox 360 Elite are all able to unleash their true potential 720p 1080p mode only through the HDMI output If you want a valid ticket to the Full HD world you either needs a compatible display with HDMI input or an HDfury4 for your existing display 1080p FULLHD as found on Blu ray and HD has over 6 times the resolution as standard DVD and TV For the best movie and home theater experience you need Blu ray HD Why do need an HDCP compliant display HDMI is a new standard that comes with a form of hardware protection called HDCP If your display doesn t have a HDMI input you won t be able to display a 720p 10
35. s all other 3D formats What 3D formats does the HDfury4 support All known 3D formats are supported including m Full 3D HD 1080 per HDMI Blu ray 1920 x 2205 24Hz m Full 3D HD 720 per HDMI Blu ray 1280 x 1470 60Hz m Top Bottom 1080p 24Hz 1920 x 1080 m Top Bottom 1080p 25Hz 1920 x 1080 m Top Bottom 1080p 30Hz 1920 x 1080 m Top Bottom 1080p 50Hz 1920 x 1080 m Top Bottom 1080p 60Hz 1920 x 1080 m Top Bottom 1080i 50Hz 1920 x 1080 m Top Bottom 1080i 60Hz 1920 x 1080 m Top Bottom 720p 30Hz 1280 x 720 m Top Bottom 720p 50Hz 1280 x 720 m Top Bottom 720p 60Hz 1280 x 720 m Side by Side 1080p 24Hz 1920 x 1080 m Side by Side 1080p 30Hz 1920 x 1080 m Side by Side 1080p 50Hz 1920 x 1080 m Side by Side 1080p 60Hz 1920 x 1080 m Side by Side 1080i 50Hz 1920 x 1080 m Side by Side 1080i 60Hz 1920 x 1080 m Side by Side 720p 50Hz 1280 x 720 m Side by Side 720p 60Hz 1280 x 720 m Frame packed 720p 30Hz 1280 x 720 m Frame packed 720p 50Hz 1280 x 720 m Frame packed 720p 60Hz 1280 x 720 m Frame packed 1080p 24Hz 1920 x 1080 m Frame packed 1080p 25Hz 1920 x 1080 m Frame packed 1080p 30Hz 1920 x 1080 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ely party and or a custom firmware can be used HDfury 4 User Manual What output resolution does the HDfury4 support with 3D content m 720p60 7
36. splay To disable the RGB Shift button set DIP switch 5 to OFF i 1234567890 To enable the RGB Shift button set DIP switch 5 to ON 1234567890 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A be party and or a custom firmware can be used HDfury 4 User Manual Power Status LED Some users may choose to disable the blue power status LED on the front of the HDfury4 When powered the HDfury4 logo will glow blue For troubleshooting purposes we recommend that you leave the power status LED enabled To disable the Power Status LED set DIP switch 6 to OFF E 1234567890 To enable the Power Status LED set DIP switch 6 to ON 1234567890 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A be party and or a custom firmware can be used HDfury 4 User Manual High Frame Rate When the switch is in the off position the framerate is limited to a maximum of 60Hz When the switch is in the on position then higher than 60Hz modes are available for 2D film 720p 60Hz and 3D sources To enable high frame rate set DIP switch 7 to ON 1234567890 To disable high frame rate set DIP switch 7 to OFF a 1234567890 Disclaimer In some countries this product will not process HDCP input Whe
37. the 3Dsync from it What is Ghosting Crosstalk or Flicker issue that people often refer to when speaking about 3D and shutter glasses The biggest drawback of Shutter glasses is Crosstalk It can be due to the decay rate of the illuminated phosphor on the picture tube If you are using a CRT display the inability of the liquid crystal panels to block the light entirely or sync errors and other factors This can cause the user to see Ghosting or Ghost images Ghosting in layman s terms means the images your right eyes sees contains some of the image intended for the left eye or vice versa The content that should be viewed only for the left eyes is shown in the left eye and little bit of it in the right eye Another common problem for inadequate hardware software and lack of stereo training is flicker which is most noticeable in standard frequency e g 60 Hz field sequential systems It varies with many factors especially screen brightness screen size and room illumination The image may still flicker even at 120 Hz screen refresh if the image is not refreshed properly Decreasing the level of ambient illumination in the room can reduce the room flicker to imperceptible levels Reducing screen luminosity with brightness and contrast controls will reduce image flicker to low or imperceptible levels We have engineered the HDfury4 and our Emitter Glasses to the highest possible standard thus giving amazing results with nearly no gh
38. to Component output mode To pass the RGB sync signals through as is set DIP switch 2 to ON and DIP switch 3 to OFF 1234567890 To force the RGB sync signals positive set DIP switch 2 to ON and DIP switch 3 to ON ON aa 1234567890 To force the RGB sync signals negative set DIP switch 2 to OFF and DIP switch 3 to ON 1234567890 To invert the RGB sync signals set DIP switch 2 to OFF and DIP switch 3 to OFF ON 1234567890 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A bE party and or a custom firmware can be used HDfury 4 User Manual Enhanced Colour Depth The HDfury4 expands colour depth from the standard 16 235 range to 0 255 in order to provide a more dynamic picture Some users may choose to disable this feature To use enhanced colour depth 0 255 set DIP switch 4 to ON ON 1234567890 To disable this feature and use normal colour depth 16 235 set DIP switch 4 to OFF J 1234567890 Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A be party and or a custom firmware can be used HDfury 4 User Manual RGB Shift RGB center adjustment Some users may choose to disable the RGB Shift button if they choose to shift the image in a video processor or in the di
39. usly had to use an amplifier the HDfury4 can most likely take its place The HDfury4 has been used with 50 foot and longer HDMI cables without issues What sort of 3D formats exist Frame packing Used by Blu ray movies and games Side by side Used by cable satellite internet mostly for documentaries Top and bottom Used by cable satellite internet mostly for movies and sports What is frame locking hear some people with digital displays have frame locking issues The frame locking issue is a result of less than ideal engineering in some digital TVs projectors It is an undocumented reality in the design of some displays where the actual visible frame rate at the display or at the lamp of a projector is in fact deviating from the intended 60Hz or 50Hz The reason is that the display cannot keep up with the decoding of the video stream or the additional video processing of the display cannot keep up The result is the display has to drop a frame here and there just to keep up This results in an actual refresh rate of something less than 60Hz e g 59 2Hz 58Hz It can be a completely dynamic phenomenon depending on the amount of action in the scene Since glasses are fixed at the frame rate of the source not the display there can be a slow drift and glasses can go out of sync with the actual visible video Your eyes cannot see this change in 2D but obviously for 3D it becomes visible HDfury4 glasses are fully customiz
40. weuhg 440 GIGI GE GH IIN4 Paxl4 NO yus WIZ OJU OIPNY 440 OIpNYy yaz 82404 NO O dogo 03 Buyers GE 440 dozz 03 bues a NO 9324 PULION 440 321 awey YIH NO 440 G31 48MOd 440 NO G31 48M0d NO Paiqesid 440 pajqeu yiys 994 NO SEZ 9L 440 SSZ 0 dap 40 09 994 NO Q yBnouusseg 440 Asod pari0y 2UAS NO O papaauy 2uAs 440 passed suds NO yndyno yusuodwio gt 440 INdyno g9Y NO Disclaimer In some countries this product will not process HDCP input When receiving content that has HDCP encryption there will be no video output A Ed party and or a custom firmware can be used HDfury 4 User Manual For your convenience the default factory settings and DIP switch features are printed on the back of the HDfury4 ON RGB output OFF Component output ON Sync passed OFF Sync inverted ON Sync forced positive OFF Passthrough ON RGB color depth 0 255 OFF 16 235 ON RGB shift enabled OFF Disabled ON Power LED ON OFF Power LED OFF ON High frame rate OFF Normal rate ON 3D scaling to 720p OFF 3D scaling to 1080p ON Force 2ch Audio OFF Audio info from sink ON Fixed Full HD 3D EDID OFF Dynamic EDID JEpE Tir HHL D 12 Default settings Preortiit Open the DIP switch cover below 3456789 The factory defaults result in the following setup DIP 1 DIP 2 DIP 3 DIP 4
Download Pdf Manuals
Related Search