Owner's Installation and Operation Manual - Dan-Corn
Contents
1. swswo008 000208JRW Failure to do so may cause serious injury or death 2 DANGER DECAL L0258A Mount DANGER DO Spredway Safety NOT ENTER this bin Keep clear of all augers Decal LO258A on bin sheet near door handle and all other entry points Also mount this decal at eye level on bin Safety decals 1 2 must be mounted durin y J sheet near ladder going to roof installation Safety decal 3 is mounted at factory Make sure location area for decal is free from grease oil and dirt Remove backing from decal and place in proper position Important If suggested locations are not clearly visible place safety decals in a more suitable area Never cover up any existing safety decals Rotating flighting will Flowing material will Crusted material will kill or dismember trap and suffocate collapse and suffocate Yearly and prior to equipment use please check that all DO NOT ENTER this bin decals and shields are in place according to these Keep clear of all augers drawings and in good legible condition Order a If you must enter the bin e Shut off and lock out all power replacement decal or shield free of charge by Use a safety harness and safety line contacting Sukup Manufacturing Co tes ele a ltt i eo wW breathi i t i Aa Address Box 677 Sheffield lowa 50475 Follow applicable safety regulations MON Ge OAOJA ARA Failure to heed these Fax 641 892 4629 warnings will result in E mail info sukup2. Replace belt 2 Belt comes off flat pulley Motor pulley not aligned w flat pulley Align pulley Motor mount bent Pitch rod is bent Belt not tight Replace motor mount Replace bent parts Replace spring amp check belt size 3 Spreading unevenly Spreader not adjusted properly Spredway not level Incoming grain spout not centered over pre spread disc Adjust spreading fin See operating instructions on page 11 Level unit Move amp secure grain spout over center of pre spread disc or use a pre spread funnel 4 Vibration Spredway improperly or insecurely mounted Check that proper brackets are used for your bin See installation instructions Tighten bolts Figure 17 Common Spredway Problems and Solutions 18 SHIPPING LISTS I Standard Spredway Box 1 Y2 HP 1PH Motor with 1 3 4 x 5 8 A pulley J0235 AP56 Belt Box 2 A3399 Safety Decal Placement Pkt w Instructions G0133 Parts Sack J0527 Bolt 5 16 18 PLT 18 J1002 Nut Hex 5 16 18 PLT 18 J1200 Washer Lock 5 16 PLT 18 J1111 Washer Flat 5 16 PLT 18 J5410 Clip Hair Pin 09 x 2 3 G0152 Cone Sub Assy Galvanized Hi Cap G01661 Fin Spreading Assy Galvanized 1 side G0197 Bracket Hanger Rigid 2006 3 G0196 Peak Ring Bracket 3 J1857 Staple for Boxing 26 J1913 Carton Spredway 24 x 24 x 24 1 L0092 G01051 Hinged H Cap Spredway
3. 3 Place hangers into slots on Spredway cone straps and lower Spredway into opening Place hangers into slots on brackets bolted to fill ring Check that Spredway is level 1 Hanger 15 3 1set G0212A Hanger 26 3 set G0213A 2 Adapter hanger bracket 3 1set GO125A 3 Bolt 5 16 18x 1 PLTD 6 J0527 4 Lockwasher 5 16 6 J1200 5 Nut 5 16 18 6 J1002 Figure 4 Super Hi Cap Drawing and Parts In some cases it may not be possible to lower the assembled Spredway through the center fill ring due to the small diameter In these cases it is recommended that a winch be placed over the fill ring to raise the Spredway from inside the bin FILL RING STANDARD POSITION LOWERED POSITION 41 8 OR 14 SPREADER CONE Bolt the Sioux brackets to Spredway cone straps with 5 16 bolts Lower Spredway into fill ring Make sure Spredway is level Mark amp drill 5 16 holes Bolt Spredway in place Use optional vertical brackets if required If pre spread funnel is used use the longer vertical brackets See Figure 5 1 Sioux bracket 3 1 set G0130A 2 Vertical bracket 7 long 3 1 set G0132A 18 long 3 1 set G0137A 3 Bolt 5 16 18 x 1 PLTD 12 18 J0527 4 Lockwasher 5 16 12 18 J1200 5 Nut 5 16 18x1 PLTD 12 18 J1002 Figure 5 Sioux Drawing and Parts MFS 1 Bolt brackets to Spredway cone straps with 5 16 bolts 2 Lower assemble
4. L Motor Decal Hi Cap L1431 Manual Spredway 1 Il Super High Capacity Spredway Box 1 1 HP 1PH Motor with Pulley 2 25 OD 625 Belt B57 Box 2 Hanger Bracket 15 3 Hanger Bracket regular 3 Cone Sub Assembly Spreader Spreader Fin Assembly 12 2 Parts Sack J0527 Screw 5 16 18 1 PLT 1 J1002 Nut Hex 5 16 18 PLT 1 0 0 J1200 Washer Lock 5 16 PLT 1 0 MI High Capacity Spredway Box 1 34 HP 1PH Motor with 2 1 4 x 5 8 B pulley J0236 BP57 Belt Box 2 A3399 Safety Decal Placement Pkt w Instructions G0133 Parts Sack J0527 Bolt 5 16 18 PLT 18 J1002 Nut Hex 5 16 18 PLT 18 J1200 Washer Lock 5 16 PLT 18 J1111 Washer Flat 5 16 PLT 18 J5410 Clip Hair Pin 09 x 2 3 G0152 Cone Sub Assy Galvanized Hi Cap G01661 Fin Spreading Assy Galvanized 1 side G0197 Bracket Hanger Rigid 2006 3 G0196 Peak Ring Bracket 3 J1857 Staple for Boxing 26 J1913 Carton Spredway 24 x 24 x 24 1 L0092 G01051 Hinged H Cap Spredway L Motor Decal Hi Cap L1431 Manual Spredway 1 Remove all parts from shipping carton and check against shipping list above Read all instructions carefully before beginning The model of your Spredway is printed on the Spredway shipping carton Standard Spredways are simply marked Spredway and High Capacity Spredways are marked High Capacity Assemble your Spredway according to
5. Sukup gt Spredway Owner s Installation and Operation Manual Sukup Manufacturing Company 1555 255th Street P O Box 677 Sheffield lowa 50475 Manual L1431 Sukup Manufacturing Company 2008 10 TABLE OF CONTENTS Proper management is essential to insure satisfactory performance Sukup Manufacturing is not liable for damage to grain resulting from improper management during drying or storage limited Wanane 3 Returned Goods Policy iranat eee ats iis Sa eae edie ea 4 Spredway Safety SECtiON wwwwwwmmmmamwmmmmiwwiwimizumwuniwim uzwa 5 l General Safety Pracucesricacivie o cuted ceca via onlatoneiaee eateries 5 Il Safety Decal Placement for Spredway ccsccceeeeeeeeeeeeeneeeeeeeeeeeeeeeeaeees 6 ASSOMOIY once eed ie ec eer tee Nee eee Error Bookmark not defined MVS Aa UE IA AA AAA reve hes WA AA AAA AAA 8 l Hanger BACK CLS 25 cox cance ose space nea cence acu tooo aon spore bon winii iii 8 Il Spredway Specifications 2cccc2e cye cs ciceeegeiees ha yest eed pee ete 10 IIl Wiring RECOMMCNOANONS scion care cern hae alas Sie ae tee 10 IM OPH GI HA eeeeeredoece 11 Operation saccade eee a eS 11 Drawings and Parts Lists 3 22 ccecc c ces25cosasentecncnntecnncien teen cperaccnasentcontndeeicaeberteentzeres 12 Troubleshooting Guide KA Kaa 18 Shipping LIStS en ee te a a Wr ene sen Or 19 l Standard SPreC Way userni UA ares alee a eae tat 19 Il Super High Capacity Spredway ccccceceeesesseceeeeeee
6. 1 G0121 5 Fin Hinge Pin w Pin Holes 1 G0122 6 Arm Control Stationary Pitch 2 G0123 7 Door Center Fill 2 G0149 04 8 Key 3 16 Sq x 1 1 G0150 9 Belt Catcher Galvanized 1 G0153 10 Tube Shaft Main Bearing Hinged 1 G0161 11 Motor Mount Spreader 1 G0262 12 Pivot Pin Motor Mount 1 G0265 13 Vane Spreading 2 G0266 Motor Spredway 1 5HP 1P 230V Super Hi Cap 1 G0272 14 Motor Spredway 1 5HP 3P 230V Super Hi Cap 1 G0273 Motor Spredway 1 5HP 3P 460V Super Hi Cap 1 G0274 15 Cone Spreader Galvanized 1 G02921 16 Bracket Center 3 G02922 17 Bracket Motor Mount Galvanized 1 G02923 18 Ring Pre Spread Super High 1 G02924 19 Fin Spreader Galvanized Super High 2 G02991 20 Bearing 1 Center FH205 16 w Locking Collar 2 J0005 21 Collar Locking 1 2 J0067 22 Flangette 3 Hole for 205 Bearing 4 J0098 23 Belt B57 1 J0235 24 Pulley 2 25 OD 625 Single B Groove 1 J0299 25 Screw 5 16 18 Ya PLT 1 J0520 26 Screw 5 16 18 1 PLT 4 J0527 27 Bolt 5 16 18 1 Carriage 8 J0535 28 Nut Hex 5 16 18 PLT 12 J1002 29 Nut 5 16 18 Nylon Lock 1 J1003 30 Washer Flat 5 16 2 J1111 31 Washer Flat 12 1 J1125 32 Washer Lock 5 16 PLT Split 10 J1200 33 Pin Cotter 1 8 1 V2 PLT 5 J1421 34 Spring Double Torsion 1 J2371 35 Clip Hair Pin 09 x 2 5 J5410 Figure 14 Super Hi Cap Spredway Galvanized G0250 Parts 15 Ill Super High Capacity Spredway Painted SWSP0001 030513RLM Figure 15 Super Hi Cap Sp
7. 2 19 x 13 BIN DIAMETER 18 33 24 48 36 60 Figure 7 Spredway Specs Provide heavy duty wiring to the Spredway motor following accepted electrical codes The operating voltages for the Spredway motors are listed here in Figure 8 Figure 8 Operating voltages FACTORY MOTOR TYPE PRE WIRED AN DIVA VOLTAGE 1 2hp 1ph 115 volts 1 2hp 3ph 230 volts 460 volts 3 4hp 1ph 115 volts 230 volts 3 4hp 3ph 230 volts 230 volts 1 1 2hp 1ph 230 volts 1 1 2hp 3ph 230 volts 460 volts Consult motor nameplate or electrical box cover as to connections needed for using alternative voltage 10 IV Option Pre Spread Funnel Uneven spreading can occur if the transport auger is not centered over the grain spreader A pre spread funnel is available which drops grain into center for more level spreading Auger Size Comp 12 G0175 10 G0155 8 G0136 6 G0154 Figure 9 Pre Spread Funnel Drawing and Comp OPERATION The Sukup Spredway contains several exclusive patented features which allow one machine to handle all types of grain spreading This spreader offers high capacity and easy adjusting The maximum capacity for the Standard Spredway is 3 000 bushels High capacity is 5 000 bushels and the Super High capacity is 7 000 bushels per hour The key to spreading grain evenly is in the pitch of the spreading fin The Sukup Spredway has been designe
8. Standard 1 J0290 14 Pulley 2 1 4 x 5 8 High Cap amp Wide Spread 1 J0299 15 Key 3 16 x 3 16 x 1 1 G0150 16 Bolt 5 16 18 x 1 Gr5 2 J0527 17 Lockwasher 5 16 PLT Split 10 J1002 18 Nut 5 16 18 10 J0527 19 Pulley 16 Cast 1 G0116 20 Locking Bolt 5 16 18 20 x 1 Gr5 2 J0527 21 Nut 5 16 18 2 J1002 22 Hair Pin Clip 2 J5410 23 Main Bearing Tube 1 G0161 24 Fin Pitch Adjusting Rod 1 G0121 25 Pitch Control Arm 2 G0123 26 Cotter Pin 1 8 x 1 1 2 5 J1421 27 Center Flow Control 2 G0149 04 28 Spreading Vane 2 G0149 03 29 Hinged Spreader Fin 2 G01661 30 Hinged Fin Pin 1 G0122 31 Belt A56 STD 1 J0235 Belt B57 HIGH CAP amp WIDE SPREAD 1 J0236 32 Bolt Carriage 5 16 18 1 8 J0535 33 Flangette 3 hole 4 J0098 34 Flat Washer 5 16 PLTD 2 J1111 35 Screw 5 16 18 3 4 1 J0520 36 Lock Nut 5 16 18 1 J1003 HINGED SPREADER FIN ASSEMBLY G0165 Figure 12 Standard and Hi Cap Spredway Galvanized GO1051 Parts 13 HI Super High Capacity Spredway Galvanized G0250 SWSP0010 03 19 2008 THW Figure 13 Super Hi Cap Spredway Galvanized G0250 Exploded View 14 Super High Capacity Spredway Galvanized G0250 Parts List 1 Handle Locking 1 2 x 5 1 2 1 G0112 2 Disk Pre Spread Standard 1 G0113 3 Pulley Flat 16 1 G0116 4 Rod Adjusting Fin Pitch
9. com serious injury or death L0258A 08 Sukup Manufacturing Company Sheffield IA USA 50475 3 WARNING DECAL L0284 Mounted on Motor Keep all shields in place Lock out all power before servicing Keep away from all moving parts KEEP AWAY FROM ALL MOVING PARTS Keep all shields in place Lock out all power before servicing FAILURE TO DO SO MAY CAUSE SERIOUS INJURY OR DEATH L0284 05 Sukup Manufacturing Company Sheffield IA 50475 ASSEMBLY Remove all parts from shipping carton and check against Shipping List on Page 19 Read all instructions carefully before beginning The model of your Spredway is printed on the Spredway shipping carton Standard Spredways are simply marked Spredway High Capacity Spredways are marked High Capacity Assemble your Spredway according to the parts drawings on this page and the following instructions 1 Bolt motor to the motor mount using four 5 16 x 1 bolts nuts and lockwashers Align motor pulley to flat pulley by sliding on motor shaft NOTE Align belt when Spredway is in operating position C di da A is ap MOTOR IT MAY BE NECESSARY TO REVERSE MOTOR PULLEY BELT HOOK FOR PULLEYS TO LINE UP BELT SHOULD RIDE CENTERED SWSP0003 ON CAST PULLEY 030515RLM Figure 1 Placement of belt on pulleys 2 Place belt on pulleys Bend belt hook around belt as sho
10. d Spredway into opening Level Spredway Mark and drill 5 16 holes for mounting bolts Bolt brackets to fill ring Use optional vertical brackets if required If pre spread funnel is used use longer vertical brackets See table below FILL RING l STANDARD POSITION LOWERED POSITION 41 4 OR 14 SPREADER CONE Figure 6 MFS Drawing and Parts 1 MFS Bracket 32 3 1 set GO126A MFS Bracket 40 3 set Q0127A MFS Bracket 60 3 set GO128A 2 Vertical Bracket 7 Long 3 1 set GO132A gt 18 Long set GO137A 3 Bolt 5 16 18 x 1 PLTD 9 15 J0527 4 Lockwasher 5 16 9 15 J1200 5 Nut 5 16 18 x 1 PLTD 9 15 J1002 In some cases it may not be possible to lower the assembled Spredway through the center fill ring due to the small diameter In these cases it is recommended that a winch be placed over the fill ring to raise the Spredway from inside the bin HIGH SUPER HIGH SMe EA CAPACITY CAPACITY CAPACITY BU HR Up to 3000 3000 5000 5000 7000 MOTOR SIZE 1 2 HP 3 4 HP 1 1 2 HP FRAME SIZE H48Z 1PH D56 3PH E56 1PH D56 3PH G56H 1PH E56 3PH SHAFT SIZE 5 8 5 8 5 8 DUTY CYCLE Continuous Continuous Continuous BELT SIZE A56 B57 B57 MOTOR PULLEY DIAM 1 3 4 2 1 4 2 1 4 PRE SPREAD DISC DIAM 3 1 2 3 1 2 8 SPREADER PAN STYLE Split Hinged Split Hinged Split Hinged CONE 19 x 12 19 x 1
11. d so that the pitch of the spreading fin may easily be adjusted from the top of the spreader By rotating the pre spread disc the pitch of the spreading fin is varied and the spreading is controlled TO ADJUST THE SPREADING PATTERN Begin with spreading fin in level position Rotate pre spread disc to tilt fin downward so bulk of grain hits bin wall approximately one ring down from eave 1 Loosen locking handle 2 Rotate pre spread disc thereby changing pitch of spreading fin NOTE When adjusting the split pan the change in pitch may not be noticeable unless weight is applied to the pan Centrifugal force will keep pan in the correct position in operation 3 Lock handle against disc It is important to realize that the optimum pitch of the spreading fin depends upon the diameter of the bin 11 the depth of grain in the bin and the amount of grain flowing through the spreader This means that the pitch of the spreading fin may require adjustment during operation in order to obtain the best results The center flow adjusting cover controls the amount of grain that falls in the center of the bin If the grain is too high in the center the cover must be rotated to make the opening smaller if the grain is too low in the center the cover must be rotated to make the opening larger The pre spread ring is designed to allow for multiple capacity rates The knockouts on the ring can be easily removed to increase these rates Pr
12. ed it is ready to be installed in bin Figures show different ways to mount Spredway Determine which you require and follow instructions for that method Spredway is shipped with a set of standard rigid mount brackets INSTALLATION I Hanger Brackets Standard and Hi Cap with Rigid Mount wa Hp FILL RING o D HP PSN o U ROOF Pio CONE o q SWSP0006 060303RLM Divide circumferences of center fill ring into 3 equal parts locate brackets so Spredway will be level If holes are provided in peak ring Steps 1 amp 2 may be eliminated 2 Mark and drill 5 16 holes and bolt brackets in place 3 Holes in Spredway have been provided in rigid mount hanger brackets to allow for multiple Spredway positions for uses in many applications Bolt Spredway to brackets using 5 16 x 1 bolts Check that Spredway is level 1 Hanger Rigid 2006 3 1 set G0197A 2 Peak Ring Bracket Rigid 3 1 set G0196A 3 Bolt 5 16 18 x 1 PLT 18 J0527 4 Lockwasher 5 16 PLT 18 J1200 5 Nut Hex 5 16 18 18 J1002 6 Washer Flat 5 16 18 J1111 Figure 3 Standard and Hi Cap w Rigid Mount Drawing and Parts Super Hi Cap Painted 1 Divide circumferences of center fill ring into 3 equal parts locate brackets so Spredway will be level FILL RING SPREADER CONE 2 Mark and drill 5 16 holes and bolt brackets in place
13. eeeeeeesceeeeeeeeeeeeneees 19 Ill High Capacity Spredway wwwwmmwwamamemiwimiwumuzazununim wawi aweza 19 CONTACT IMO MaOM AA AAA 20 Sukup Manufacturing Company U ku PO Box 677 Sheffield IA 50475 Phone 641 892 4222 Fax 641 892 4629 E mail Info sukup com Visit us at www sukup com LIMITED WARRANTY SUKUP MANUFACTURING COMPANY Sukup warrants to original retail purchaser that within time limits set forth new equipment shall be free from defects in material and workmanship A part will not be considered defective if it substantially fulfills performance specifications Should any part prove defective within the warranty period the part will be replaced without charge F O B Sukup Mfg Co Sheffield Ilowa USA or Distribution Centers Arcola Illinois Aurora Nebraska Cameron Missouri Defiance Ohio Jonesboro Arkansas Watertown South Dakota To obtain warranty a copy of original invoice is required THE FOREGOING LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OF MERCHANTABILITY FITNESS OR PURPOSE AND OF ANY OTHER TYPE WHETHER EXPRESSED OR IMPLIED Sukup neither assumes nor authorizes anyone to assume for it any other obligation or liability in connection with said part and will not be liable for incidental or consequential damages THE REMEDIES STATED HEREIN SHALL BE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS LIMITED WARRANTY Sukup reserves the right to change specifications add improvement
14. hio Jonesboro Arkansas Watertown South Dakota Warranty items may be returned without prior authorization provided all the following information is included Part number description of part how it failed and date of failure Give detailed explanation of what happened do not just write defective A copy of invoice with date on which part was originally obtained and date of installation Preferences as to whether part is to be replaced repaired or credit issued Complete company name address and telephone number of firm receiving replacement part or credit State name and phone number of a person that should be contacted if there are further questions NOTE To obtain two year stirring auger warranty top 18 of down auger must be returned Due to the affect that stirring augers have on bearings motors belts etc using non Sukup stirring augers voids warranty See reverse side for warranty information and policy Non Warranty Items C O D shipments will not be accepted Equipment returned must have proper approval by a Sukup representative through a Return Authorization Form A copy of the original invoice pertaining to item must be provided when requesting credit Credit will be based upon original invoice price or price at time of return whichever is lower There is a 25 restocking charge on all equipment authorized for return unless equipment is under warranty or was shipped incorrectly No new equipment may be
15. icates a potentially hazardous situation which if not avoided could result in death or serious injury and includes hazards that are exposed when guards are removed It may also be used to alert against unsafe practices 4 amp CAUTION yellow indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices FOLLOW MACHINE SAFETY SIGNS amp MESSAGES Observe safe operating practices Carefully read this manual and all safety signs on your equipment Safety signs must be kept in good condition Replace missing or damaged safety decals or shields available from Sukup Manufacturing Co Box 677 Sheffield lowa 50475 at no charge Learn how to use controls and operate equipment Do not let anyone operate unit especially youth without thorough training of basic operating and safety procedures Make no unauthorized modifications to equipment Modifications may endanger function and or safety of unit Periodically check all mechanical and electrical components Keep unit in good working condition NEVER NEVER clean out bin with augers running When bin is nearly empty sweep o floor augers travel at increasing speed just turning around can give augers time enough to trap you Exposed auger in sump can cause serious injury if stepped or fallen into Failure to follow the above precautions may cause seriou
16. oper settings are essential for peak performance Use chart below as a guideline Ring Size Rate of Flow 6 1500 Bu Hr 8 2600 Bu Hr 10 4000 Bu Hr Figure 10 Pre spread Ring Size Flow Rate THE INCOMING GRAIN FLOW MUST BE CENTERED OVER THE PRE SPREAD DISC FOR EVEN SPREADING DRAWINGS AND PARTS LISTS l Standard and High Capacity Spredway Galvanized G01051 Excluding motor SWSP0002 030512DDV READ ULA Figure 11 Standard and Hi Cap Spredway Galvanized G01051 Exploded View 12 Standard and High Capacity Spredway Galvanized G01051 Excluding motor Parts List All parts except those designated as Standard or High Capacity are interchangeable between Standard and High Capacity Spreaders 1 Locking Handle 1 G0112 2 Pre spread Ring with knockouts 1 G0182 3 Pre spread Disc 3 1 2 1 GO111 4 Pivot Pin 1 G0265 5 Bearing 1 Center w locking collar 2 J0005 6 Cone 1 G0145 7 Motor Mount 1 G01455 8 Spring Double Torsion 1 J2371 9 Flatwasher 1 2 PLT Optional Ji 125 10 Belt Hook 1 G0153 11 Motor 5hp 1ph 115v wired Standard G0138 Motor 5hp 3ph 230v wired Standard G0140 Motor 5hp 3ph 440v wired Standard G0146 12 Motor 75hp 1ph 115v wired High Cap amp Wide Spread 1 G0142 Motor 75hp 3ph 230v wired High Cap amp Wide Spread G0144 Motor 75hp 3ph 440v wired High Cap amp Wide Spread G0148 13 Pulley 1 3 4 x 5 8
17. redway Painted Exploded View Super High Capacity Spredway Painted Parts List 1 Motor 1 1 2hp 1ph 230V wired G0272 Motor 1 1 2hp 3ph 230V wired G0273 Motor 1 1 2hp 3ph 460V wired G0275 2 Belt B57 1 J0236 3 Screw 5 16 18 1 PLT Gr 5 HHCS 10 J0527 4 Washer Lock 5 16 PLT Split 10 J1200 5 Nut Hex 5 16 18 PLT 6 J1002 6 Motor Cover Spredway 1 G0210 7 Spreading Pan Complete 12 2 G0263 8 Spreading Fin Only Hinged 12 1 G0267 9 Spreading Vane 1 G0266 10 Cover Center Flow Adjusting 1 G0117 11 Stationary Pitch Control Arm 1 G0123 12 Clip Hair Pin 09 x 2 9 J5410 13 Cone Weldment Spredway Commercial 1 G0260 14 Bearing 1 Cnt F PB W SS FHSR205 16 2 J0030 15 Handle Locking 1 2 x 5 1 2 1 G0112 16 Disk Pre Spread Standard 1 G0113 17 Fin Pitch Adjusting Rod 1 G0121 18 Tube Shaft Main Bearing Hinged 1 G0161 19 Spring Complete 120WR 7 Coils 2 J2365 20 Shaft Collar 1 1 J1335 21 Motor Mount Spreader 12 1 G0262 22 Tension Pin Weldment Spreader 1 G0261 23 Lock Collar 1 2 1 J1320 24 Motor Pivot Pin Spreader 1 G0265 25 Pulley Flat 16 1 G0116 26 Fin Hinge Pin w Pin Holes 1 G0122 27 Pulley 2 25 OD 625 Single B GRV 1 J0299 Figure 16 Super Hi Cap Spredway Painted Parts 17 PROBLEM REASON TROUBLESHOOTING GUIDE SOLUTION 1 Does not run Fuses blown Replace fuses Belt off
18. returned for credit or exchange without advanced written authorization from Sukup Manufacturing Company Custom built or obsolete equipment may not be returned Returned Goods Allowance Guidelines 100 Parts under warranty 75 Restocking new merchandise undamaged and in original carton 65 New merchandise requires repainting or repacking 0 60 Damaged new equipment describe extent of damage 0 Used equipment out of warranty unsalable merchandise obsolete equipment custom built equipment and unauthorized returns SPREDWAY SAFETY SECTION I General Safety Practices RECOGNIZE SAFETY ALERT SYMBOL The American Society of Agricultural and Biological Engineers ASABE safety alert symbol means ATTENTION Be Alert Your personal safety is involved This symbol draws your attention to important instructions concerning your personal safety Read the messages carefully to avoid personal injury or death NOTE Spredway itself is shielded by location but undoubtedly unload equipment will be installed in the same bin thus making for a hazardous situation SAFETY SIGNAL WORDS On safety decals three signal words are used with corresponding colors of red orange and yellow to indicate hazard intensity Definitions are as follows WINN Niels ed indicates an imminently hazardous situation which if not avoided will result in death or serious injury 4 amp WARNING orange ind
19. s injury or death NEVER ENTER BIN f DANGER Never enter bin unless all power is locked off and another person is present Rotating augers can kill or dismember Flowing grain may trap and suffocate If you enter a bin of flowing grain you can be completely submerged in grain in about 8 seconds Failure to heed this warning may cause serious injury or death CAUTION Metal edges are sharp To avoid injuries wear protective clothing and handle equipment and parts with care Failure to do so may cause serious injury EMERGENCIES KNOW WHAT TO DO Have emergency numbers near your telephone Doctor Emergency Medical Squad Ambulance Service Hospital Fire Department Written Directions to Your Location ll Safety Decal Placement for Spredway avoid falls never carry items while climbing on decal on bin sheet near door handle bin Maintain secure hand and foothold when climbing on bin T CAUTION Metal is slippery when wet To 1 WARNING DECAL L0281 Mount safe operation TO AVOID SERIOUS INJURY OR DEATH Read operator s manual before operating amp follow j e Know how to shut off power quickly Keep people especially children away from unit at all times Lock out all power and have another person IN present when servicing unit Ww Replacement safety shields and decals are available free of charge 0281 07 Sukup Manufacturing Company Sheffield 1A USA 50475 a
20. s or discontinue manufacture of any of its equipment without notice or obligation to purchasers of its equipment This warranty gives you specific legal rights You may also have other rights which vary according to state or province WARRANTY EXCLUSIONS Labor transportation or any cost related to a service call is not provided by Sukup This Limited Warranty does not apply to damage resulting from misuse neglect normal wear accident or improper installation or maintenance ITEMS NOT MANUFACTURED BY SUKUP i e Tires Belts Motors etc ARE COVERED UNDER WARRANTIES OF THEIR RESPECTIVE MANUFACTURERS AND ARE EXCLUDED FROM COVERAGE UNDER THE SUKUP WARRANTY Since the down augers are so critical to the successful operation of the stirring machine Sukup Mfg will not warranty any machines unless they are equipped with Sukup down augers BASIC WARRANTY All Sukup manufactured products are warranted for one year from date of purchase EXTENDED STIRRING MACHINE WARRANTY Sukup warrants Stirring Machines for two years from date of purchase EXTENDED STIRRING AUGER WARRANTY Stirring Augers are warranted for two years from date of purchase Must return top 18 of down auger to obtain credit EXTENDED FAN WARRANTY Sukup warrants fans for two years from date of purchase EXTENDED GRAIN DRYER WARRANTY Sukup warrants portable grain dryers for two years from date of purchase EXTENDED HEATER CIRCUIT BOARD WARRANTY Sukup warrants heater circui
21. t boards for three years from date of purchase ELECTRIC MOTOR WARRANTY The manufacturers of electric motors warranty their motors through authorized service centers Contact motor manufacturer for nearest location If motor warranty is refused by a service center based upon date of manufacture use the following procedure Have the motor repair shop fill out the warranty report form as if they were providing warranty service State on the report the reason for the refusal Send the report motor nameplate and proof of purchase date to Sukup If electric motor warranty is not satisfactorily handled by motor service center contact Sukup for assistance Warranty may also be obtained by returning motor to Sukup Mfg Co or Distribution Centers with prior authorization NOTE Sukup will not be responsible for unauthorized motor replacement or repair WARRANTY CERTIFICATION Warranty registration card should be mailed within two weeks of product delivery to certify warranty coverage UNAPPROVED PARTS OR MODIFICATION All obligations of Sukup under this warranty are terminated if unapproved parts such as stirring augers are used or if equipment is modified or altered in any way not approved by Sukup 12 19 06 RETURNED GOODS POLICY Warranty Items C O D shipments will not be accepted Warranty parts may be returned to Sukup Mfg Co Sheffield lowa or Distribution Centers Arcola Illinois Aurora Nebraska Cameron Missouri Defiance O
22. the parts drawings and instructions on Page 7 19 CONTACT INFORMATION Owner s manuals are available from Sukup and additional copies can be requested at the address phone number or e mail address shown below Please indicate manual number L1431 when requesting the Spredway Owners Installation and Operation Manual Sukup Dealer Information Dealer Name Address Cell phone Office phone Fax A In Case of Emergenc A Have emergency numbers and written directions to your location near a phone and arrange and practice a safety plan Doctor Emergency Medical Squad Ambulance Service Hospital Fire Department Written Directions to Your Location Sukup Sukup Manufacturing Company 1555 255th Street Box 677 Sheffield lowa USA 50475 0677 Phone 641 892 4222 Fax 641 892 4629 Website www sukup com Email info sukup com
23. wn above CAUTION Belt should not scrape on hook as it may cut belt 3 The center flow adjusting cover on the spreading fin should be opened about 1 3 for bins less than 24 in diameter For larger bins the center flow adjusting cover should be opened to 1 2 Be sure bolt on cover is tight after adjustment 4 To mount fin to spreader lower pitch adjusting rod by loosening locking handle and pre spread disc inside of cone Lower adjusting rod so the end is approximately 3 below the main bearing shaft See Figure 2 One end of the stationary pitch control arm comes mounted to fin Mount other end of control arm to main bearing shaft Secure with hairpin clips Repeat step for second fin MAIN BEARING SHAFT STATIONARY PITCH CONTROL ARM SPREADING FIN A SWSP0007 060125RLM FIGURE 2 Figure 2 Mounting fins to spreader 5 Remove hinge pin from adjusting rod Place spreading fins and pitch adjusting rod together and replace hinge pin Secure hinge pin with hairpin clip Hairpin clips should be snapped on all the way See Figure 2 See operating instructions for setting fin angle Place pre spread ring inside cone allowing slots in ring to slip over Spredway arms Secure ring by installing hairpin clips found in parts sack through holes provided in Spredway arms When Spredway has been assembl
Download Pdf Manuals
Related Search