Home

USER'S MANUAL VC

1. 1 Tx Transmit Data MX TX Transmit Data Unwed Unused 5 Umea Used CE 7 Umea Used 8 Umea Unsed Please make sure your connected cables have the same pin assignment as the table above before deploying the cables into Figure A 1 Standard RJ 45 receptacle connector your network 216 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 1 1 o 2 3 3 4 4 5 45 6 6 T E 8 8 Ed White Orange El White Orange BE Orange BE Orange Ed White Green Ea White Green MA Blue MA Blue White Blue White Blue A Green A Green E White Brown E White Brown MA Brown MA Brown Figure A 2 Pin Assignments and Wiring for an RJ 45 Straight Through Cable 1 2 3 A 5 6 T 8 Ea White Orange BE White Green BE Orange MM Green Ed White Green Ea White Orange MA Blue E White Brown White Blue EN Brown BE Green MM Orange Ey White Brown MA Blue A Brown White Blue Figure A 3 Pin Assignments and Wiring for an RJ 45 Crossover Cable A 2 Telephone wire 217 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Standard telephone wire of any gauge or type flat twisted or quad is used to connect the Modem to the telephone network A telephone cable typically consists of three pairs of wires one of which is used for transmission The connector at the end of the telephone cable is called an RJ 11 con
2. Fields in LAN Statistics Field Description Interface Name of LAN Interface e g ethO usbO etc Receive Counters Total packets received from this interface Total bytes received form this interface Total Erroneous packets on this interface Total Dropped packets on this interface 55 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 4 2 WAN For viewing WAN Statistics click the WAN link Statistics gt WAN on the left navigation bar A screen is displayed as shown in Figure 4 4 2 System Statistics LAN m WAN Statistics The WAN Statistics gives the per interface statistics on the WAN side WAN xDSL WAN LAN Route gt Firewall NAT gt QoS TX RX Interface WAN Channel Connection T Packets Bytes Errors Dropped ptmO PTM VLAN Fix IP 4128 1602641 O 4 3207 734760 0 0 Figure 4 4 2 WAN Statistics The screen contains the following details Fields in WAN Statistics Description 56 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Fields in WAN Statistics cont d Description Transmit Counters for WAN interface Total packets transmitted from this interface Total bytes transmitted form this interface Total Erroneous packets transmitted on this interface Total Dropped packets transmitted on this interface oy VC 400RTW VDSL2 Slave Mode
3. premises or within buildings It was defined in standard ITU T G 993 2 finalized in 2005 VDSL2 was the newest and most advanced standard of digital subscriber line DSL broadband wire 3 3 line communications Designed to support the wide deployment of triple play services such as voice video data high definition television HDTV and interactive gaming VDSL2 was intended to enable 3 operators and carriers to gradually flexibly and cost efficiently upgrade existing xDSL infrastructure The protocol was standardized in the International Telecommunication Union telecommunications sector ITU T as Recommendation G 993 2 It was announced as finalized on 27 May 2005 1 and 228 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel r MMM A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A aaa Maaa aM MiM aiM aiaiai aM MaMia iiiiiiiiiiiiiiii i i 4 3 first published on 17 February 2006 Several corrections and amendments were published in 2007 through 2011 3 VDSL2 is an enhancement to very high bit rate digital subscriber line VDSL Recommendation 3 G 993 1 It permits the transmission of asymmetric and symmetric aggregate data rates up to 200 3 Mbit s downstream and upstream on twisted pairs using a bandwidth up to 30 MHz VDSL2 deteriorates quickly from a theoretical maxi
4. Annex AM9_EU64 2 VDSL2Profilegc_________8__ Annex B 997 M2x A B05 3 VDSL2 Profile8d 9 Annex B 997 M2x M B06 4 VDSL2Profilei2a 2110 Annex B 997 Mic A 7 B07 5 VDSL2Profilei2o 2111 Annex B 998 M1x B B08 Annex B 998 M2x M B11 Annex B 998 M2x B B12 i 6 VDSL2Profilet7a _ 8 VDSL2 Profile17b_ OD 225 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Oc U oa No Sn wo m Mm 8 226 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Ve TT dH Troubleshooting Diagnosing the Router s Indicators The router can be easily monitored through its comprehensive panel indicators These indicators assist the network manager in identifying problems the hub may encounter This section describes common problems you may encounter and possible solutions Cause Defective External power supply A BEEERREEREEEREHEEEEEIRIEERIRIEHTETETEETRETEETETTEIEERETTETSERETSERETEITERSTSTEEREERTTEERTIRTEISTIETERSETITREETSETIEEESHETEEEETEEEETEEREEESEEEHEITELTEIEESEEIEREEEEHEIEIEETEERTEIEEETEIEESREIEEIEEIHETTEEHETEEREEHEITERREITESEREITEEREITEEREEEEREIRIEERTEREREERESTEIREEREIREEEIEEREIEHEREITEEREERERHEIRESCEIREROEISEREEIEHEOEITEROESTEEETERICHEREIHEEERRRESREERETERERREREERETEREREERRERTTRRERTERRERTERRERTTEREREIRSERERRERRSTEREREERSEREERSEREERSERSTEROEREREREREERRERRSREEEREERERBERREIESRRERREERERRSEREREIEERRSEREERETRTTREERERREEREITSERETE
5. Click Cancel to exit from this page without saving the changes Click Apply for deleting the WAN connection For enabling IPv6 function click the IPv6 setting link IPv6 gt IPv6 setting on the left navigation bar 94 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 8 DDNS The Dynamic DNS is useful for getting a FQDN URL registered for a dynamic IP address to a DNS service provider The wireless router software integrates support for three Dynamic DNS service providers dhs dyndns e dyns The user needs to register first with a chosen DNS Service provider The registered information needs to be configured in DDNS settings web page To configure thee registered information in DDNS settings page click the DDNS link WAN gt DDNS on the left navigation bar A screen is displayed as shown in Figure 4 6 8 DDNS Settings Dynamic DNS allows you to update your dynamic IP address with one or many dynamic DNS services So anyone can access your FTP or Web service on your computer using DNS like address Enable DDNS Support F a rc Wappen Y aan En u Ze a dyn dhs org O dyndns dyndns org I O dyns I dyns ck o 1 Figure 4 6 8 DDNS Settings 95 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in DDNS
6. For installing a SSL Certificate for SSL tunnel click the SSL Certificate link System gt SSL Certificate on the left navigation bar A screen is displayed as shown in Figure 4 3 8 SSL Certificate Copy and Paste your SSL Certificate in the text box This certificate is used for HTTPS access to CPE TESTA PRT MARGAI DERM Exz W XJpU21inbiBUenYzdi YXOgaF ROcAM6Ly93d3cudm Vay gt MDAWMDAwWIH 1cHNMT owh 3 WS MSIMIOTUSWICHLTTELMAEGATIUEBHMNEVVME Fj DU51 qdyBiYWiwezhpcmUxEzARBoNVBAcUCIBycnkKzbWSldtboxEDACRGNVBADSDUBIFE cy terug TENA AMUXETAPE GI Eon VHTMwHOYDVQOLFCpUZzAxAUtcy xogas dsLnzl SEGMEMDUFFZAVBGNVBAMU Prats POSTA A 1369 Ar benFAQESYLGnmMOURJSGEFTRgs4gl FYHAXRR5t EMauyxA xrTSaN92w Tr 7 IDLSEFbhSsbau2 22V zg3cbingd4t egz4VCLIulVvidoGL7TEgjE 0b1lafH mn CiilePwy TCRhlukp51 1 Wwahl Figure 4 3 8 SSL Certificate Click Apply to install the entered certificate Click Cancel to cancel the installation of entered certificate 51 zi a ra E T cE 3 4 a 3AE FAAOCAQZAMIIBCOKCAQEAV2 1T Qui Kiss d1N7ihZecomtkiel3t1sDANBgkgqhki697y0BAQUEFADES zZAVBGNVBACTDIZIicm1 TaWduLcBubmMuMR3 ee Se TE ee LEzZYOUZXJtcyBvZi cudmWyakNpZ24uY23tctL3JUwWYSAoYyEXMDEYMCOGAIL aYNpZ220 2xhc SMOMYBTZWN cm gU2VyanVYIENBICOGRZMUHRCNMITWNDIW A nitYs kuktz TosiOuxYms SfDSsqucWzkbqshy a 5usnyT cdY5aHW ENZK4GSKMIEOICRTEA EYbSdauqlikYn72f0YSSshct VFcydR XyjadL4q zWFT Help TEAN
7. VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Diagnostic Test Suite Field Description Connection Status WAN DSL WAN State ENET LAN O Ethernet LAN Port 0 state ENET LAN 2 Ethernet LAN Port 2 state LAN Connectivity of CPE Testing LAN Status of LAN connection Diagnostics Connection Testing xDSL Connection Testing xDSL Synchronization xDSL Synchronization Test Testing ATM Connection on default WAN ATM PVC Testing ATM OAM F5 End to End Ping FS end to end ping test Testing Internet Connectivity Ping to Gateway Ping to Gateway IP address Start Diagnostics Test Initiates the Diagnostics test Note Please wait a few seconds to show the test result a 215 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel NeT o 24 Cable Requirements A 1 Ethernet Cable A CAT 3 7 UTP unshielded twisted pair cable is typically used to connect the Ethernet device to the router A 10Base T cable often consists of four pairs of wires two of which are used for transmission The connector at the end of the 10Base T cable is referred to as an RJ 45 connector and it consists of eight pins The Ethernet standard uses pins 1 2 3 and 6 for data transmission purposes Table A 1 Table A 1 RJ 45 Ethernet Connector Pin Assignments Media Dependent Media Dependent interface interface cross
8. _ _ _ _ _ _ _ _A _ _ A E _ gt gt gt _ _ _ _ _ A _ _ A _ _ gt _ _ _ _ _ __ _ _ __ _ _ _ _ __ A _ _ _ _ _ __ _ _ ___ _ ___ _ __ _ _ ____ ___ ____ __ __ _ __ __ _ _ __ ____ ___ __ _ __ _ _ ___ __ ___ _ _ __ _ _ _ _ connected by the Shannon Hartley theorem 3 In digital communications the SNR will probably cause a reduction in data speed because of frequent errors that require the source transmitting computer or terminal to resend some packets of 3 data SNR measures the quality of a transmission channel over a network channel The greater the ratio the easier it is to identify and subsequently isolate and eliminate the source of noise Some testing programs which are based on TCP IP protocols such as FTP Iperf NetlQ the testing 3 ____ bandwidth outcome will be limited by TCP window size u We recommend testing VDSL2 bandwidth using Smartbits equipment or IPERF program The 3 Solution TCP window size must be set to max 64k the parameter as iperf server IP address i 1 t 50 aw 65535 for client side Please note wireless router is a remote side CPE side it must be connected to the CO side to work Answer Tone mode Band profile and band plan settings must be compatible with each other if not access error will show when applied Please d
9. Backup to local host This will backup the current active configuration of CPE in Host machine Click Next to start the firmware upgrade process Click Cancel to exit from this page without saving the changes 45 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel m Backup Current Active Configuration As mentioned before this option allows users to backup the current active configuration running in the router system This is very helpful when a user wants to backup the current working configuration of the router for rollbacks if required in future It is recommended that before any complex nature of configuration is done by user the current active configuration should be backed up in host machine The Local Host Configuration backup is shown in Figure 4 3 6 1 Configuration Backup This feature saves the configuration of the device to a file in gzipped format Click Here Figure 4 3 6 1 Configuration Backup When you click the Backup button as shown in Figure 4 3 6 1 it will backup the configuration settings of CPE in connected PC from where Web Ul is being accessed E Restore Previous Backed up Configuration 46 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel As mentioned before this option allows the user to restore the earlier backed up configuration in router system This operation is handy for restoring the system to last backed up c
10. Click Cancel to exit from this page without saving the changes 121 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 8 3 Routing Table List The Routing table allows you to see how many routings on your VDSL2 router routing table and interface information For viewing the Routing entry table list of wireless router click on the Routing Table List link in the left navigation bar A screen is displayed as shown in Figure 4 8 3 Routing Table The Routing table displays configured routes and interfaces on CPE device 192 168 16 0 Ee Babe a Bebe be Ai 0 0 0 0 Figure 4 8 3 Routing Table List 122 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Static Routing Field Description Destination IP Destination IPv4 address for route Gateway IPv4 gateway address for this route This depends on the interfaces currently configured in the system Possible values are brO Bridge interface ethO First Ethernet interface eth1 Second Ethernet Interface interface maybe connected to an external switch nas lt i gt e g nasO Ethernet over ATM interface Applicable only to ATM WAN ppp lt i gt e g pppO PPPoE or PPPoA interface 123 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Routing Table List IPv6 Tab If IPv6
11. WAN Status N N PPPoE UNCONFIGURED UNCONFIGURED WANPPP1 Connect Gateway Information DNS Information Primary Secondary Figure 4 6 6 1 WAN Status IPv6 Tab The screen contains the details as described in table of Fields in WAN Status For enabling IPv6 function click the IPv6 setting link IPv6 gt IPv6 setting on the left navigation bar VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 7 DNS For configuring the Domain Name Server DNS address click the DNS link WAN gt DNS on the left navigation bar A screen is displayed as shown in Figure 4 6 7 For statically configured WAN it is mandatory to configure DNS addresses through this page Domain Name System DNS A Domain Name System DNS server translates hostnames or domain names to IP addresses Most ISPs provide a DNS server for speed and convenience Since your Service Provider may connect to the Internet with dynamic IP settings it is likely that the DNS server IP addresses are also provided dynamically However if there is a DNS server that you would rather use you need to specify the IP address below pva er Domain Name Server DNS Address Secondary DNS Address optional Y Figure 4 6 7 DNS Configuration 93 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in DNS Description
12. on the left navigation bar This can be used for allowing specified IP addresses to access the wireless router CPE from WAN The system allows up to 16 ACL entries to be configured in the CPE device A screen is displayed as shown in Figure 4 10 7 Access Control IP Address Access to the device is restricted to IP Addresses listed here LC Enable ACL IC ES 7777 0D a JJ a mn FF Ww N mr Figure 4 10 7 Application Server Settings 161 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in ACL Setting Field Description Enable ACL To enable disable ACL settings Click Apply after filling the IP address for adding the entry in ACL list Click Cancel to exit from this page without saving the changes 162 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 11 NAT You can view the NAT on the left navigation bar of the wireless router CPE homepage The menu below includes the sub menus of LME Virtual Server ATM rr and DMZI Following are the options available under NAT as shown in Figure 4 10 NAT Settings Virtual Server Port Triggering DMZ Figure 4 11 NAT Options 163 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 11 1 NAT Settings For configuring Network Address Translation NAT click the NAT Settings link NAT gt
13. 22 gt gt gt gt 2 gt gt gt 2 gt gt 2 gt 2 gt gt gt 2 gt gt 2 gt gt gt gt gt gt 2 gt gt gt 2 gt 2 gt gt 2 23 IPv6 Firewall Settings Firewall Mode 1 No firewall rules IPv6 Firewall Settings You can configure IPv6 firewall settings You can configure IPv6 firewall settings ae EA Firewall Mode hi Firewall Mode TN o Bea hoe coe tcp traffics Allow all outbound and pinhole defined inbound traffic telnet 23 ftp 21 http 80 https 443 smtp 25 pop3 110 imaps 993 ntp 123 Allow allow inbound IPsec AH 50 3 Allow outbound icmpv traffic Allow allow inbound IPsec ESP 51 4 Allow only related established inbound traffic that is initiated by above outbound traffic Allow allow inbound IKE 500 5 Rest all are dropped Allow related established inbound traffic that is initiated by above outbound traffic tn L PB A cee ew EO mB eww nn nn ww wwe we E ww ewww ew ew wm www ww ewww ww wwe www ew ew eww ew ww ww ew eww ww E e ww ew ew ew ww ww ew E ww E E E ew me OTE E E E E O ww mw ww an ew ww ow ow E E ew we E E E NE E ow E ow mw ew ww ow E ow ww wm ww ow ww ow E E E ww www E ow ow E om amp amp 7 Figure 4 10 2 IPv6 Firewall Setting 139 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in UPnP Settings Field Description Firewall Mode The ava
14. Ad did bbdd boda 116 SA o e one E E ae eT eC er ane ater Uneaten er tee 117 4 82 BIP SUBBON OA oo Pr 120 TO ROUUNG a ADEE ee ee ee 122 AAA 125 ARAO SEN rer A a 126 49 2 OCU SENGS ira E AAA ER 128 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel ATO SLO CU URS Wy A ac ace iii 137 AOA FIrEWA SEI NO tantas eek mie masse 138 4 10 2 1P v6 Firewall Selling area ine 139 AS EB IC EEMO e E erreeneneeeenee 141 210 4 URL FMI ae A A A AAA 155 a A nenne 157 4 10 06 Applieation Selver Selling viii NAAA 159 A057 ACCESSO ONTO LIE AO 161 A PP en eee ee ene ee ree nee te 163 AITEEINATSelingssme ne nee es 164 o A 165 SA 20 01 a Ad 0 A 171 a Dad a ler BB VRR SENAT NEE ea o ee eee 177 O ee ee ee er een en ee ee een ee een 180 AV QOS SC UNOS a Reine 181 LB 00 480 7110 0 All ON sense aaa 184 ATES Glass COAUTOR al el a cmt aa AAA Al a a aa aa 189 A oy q tee een ee eee oe etme ace N 195 412 1 A A acide recat stadt acacia sce elated tind Pt aedbin inch edt dubbed AAE EEE 196 4 1229 IO OPO HS SC UNO Sadie 198 4 12 3 Advanced DCUINGS eos ell 200 O e E EE 202 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 13 1 Tunnel Mode e 203 A A pr 206 A IN ee ee es 207 AS AP ee EE EEEE 209 A A 211 A A o en eee nce ecetecennced acesanimeueenecteemceentese 213 2 19 21 DATO SUE TES tt did eee 214 APRENDI CABLE REQUIREMENTS uc ccceccecceccceccecce
15. Auto Detect Select this to enable VLAN auto detection from the specified pool for MII 1 WAN mode Select this to enable WAN auto detection in sequence of PPPoE DHCP in ADSL ATM WAN mode L3 VCC Auto Detect Select this to enable WAN auto detection in sequence of PPPoE DHCP in VDSL PTM L3 VDSL PTM VLAN Auto Detect WAN mode Select this to enable WAN auto detection in sequence of PPPoE DHCP in MII O WAN L3 MII O VLAN Auto Detect d mode 66 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 3 WAN Channel Configuration For configuring the WAN Channel Configuration click the WAN Channel Config WAN gt WAN Channel Config on the left navigation bar A screen is displayed as shown in Figure 4 6 3 WAN Channel Configuration This page allows management of layer 2 channels for WAN Auto Detect Enable Figure 4 6 3 WAN Channel Configuration This page allows management of layer 2 channels for WAN Auto Detect Enable F ATM Channel Name VPI VCI Encapsulation Mode Link type ATM Qo5 vcc channel i 0 35 LLE SHAP rfc2684 ena UBR nas Figure 4 6 3 1 WAN Channel Configuration Auto Detecting does not check the checkbox 67 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in WAN Channel Configuration Description The ATM based WAN channels are configure
16. Port Triggering Add 174 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Port Triggering Field Description Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 175 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 176 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 11 4 DMZ For configuring the DMZ Demilitarized Zone click the DMZ link NAT gt DMZ on the left navigation bar Upon configuration of DMZ all traffic sent towards RG would be unconditionally forwarded to DMZ LAN Host A screen is displayed as shown in Figure 4 10 4 DMZ Demilitarized Zone If you have a local client PC that cannot run an Internet application properly from behind the NAT firewall you can open the client up to unrestricted two way Internet access by defining a virtual DMZ Host Enable IF Address of Virtual DMZ Host 1192 168 11 Oooo Figure 4 11 4 DMZ Demilitarized Zone 177 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in DMZ Field Description To enable or disable the DMZ setting of wireless router CPE Select
17. Settings User Account Management lf you want to change the password for the administrator click the Administrator Settings link System gt Administrator Settings in the left navigation bar A screen is displayed as shown in Figure 4 3 3 This page allows the user to change the login password User Management Manage user accounts and access permissions on CPE device Password less login u Account Option Edit Enable Resource Access Web access Local E Remote File Share access ET Samba Telnet access Figure 4 3 3 Administrator Settings Fields in Administrator Settings Field Description Select User Select user type The available options are admin and support _user 41 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Fields in Resource Access Field Description File Share Access File share Access Permission FTP Samba or both Fields in Account Option Selected Edit boxes Field Description Current Password The user should specify the current login password Re type Password The user should re type the new password entered in previous field Account Option Edit Enable User Name admin Current Password New Password password can be 3 16 Characters without white space Figure 4 3 3 1 Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the change
18. To enter the destination IP Address of routing entry Enter the IP Address 0 0 0 0 of Destination LAN IP routing entry To enter the Gateway address of routing entry Enter the Gateway address of routing entry Click Add to create a new static route of specified destination IP Netmask and Gateway values Click Cancel to exit from this page without saving the changes Notes 1 Static Routing functionality is used to define the connected Gateway between the LAN and WAN For example if we want to activate the Network Time Protocol NTP service we have to define the Gateway connected to NTP server in the WAN 2 The gateway of static routing is just used for switch Bridged mode 3 The gateway IP domain should be the same LAN e g if the LAN IP is 192 168 1 1 the gateway IP should be 192 168 1 X where X represents a number range is 2 255 118 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel When you click the IPV6 tab in the Static Routing page a screen is displayed as shown in Figure 4 8 1 1 the addition and deletion of static IPv6 routes are not supported currently Static Routing The static routing function determines the path that data follows over your network before and after it passes through your router You can use static routing to allow different IP domain users to access the Internet through this device v EJ Prefix Length u
19. VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Add IPSec Add Configuration Field Description IPsec Tunnel name PSK Secret Shared secret string used for tunnel authentication WAN Interface WAN on which the tunnel will be created Peer Address Remote tunnel end point address Enable or Disable of tunnel IKE Hash Hash algorithm to be selected from dropdown IKE PRF PRF algorithm to be selected from dropdown ESP Hash ESP Hash algorithm to be selected from dropdown Number of retries in case key exchange fails Click Apply for applying the configured IPsec tunnel Click Cancel to exit from this page without saving the changes 205 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 14 IPv6 When clicking on the IPv6 link on the left navigation bar of the wireless router CPE homepage The menu below includes the sub menus Of ANE as AA een and PESA tente The following options are available as shown in Figure 4 14 IPv6 Setting 6RD Configuration DS Lite Configuration Figure 4 14 IPv6 Options 206 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 14 1 IPv6 Setting To enable or disable IPv6 functionality in CPE click on the IPv6 Setting link on the left navigation bar A screen is displayed as shown in Figure 4
20. Virtual Path Identifier VCI Virtual Connection Identifier Loopback Enabled or Disabled Transmit Time actual value in milliseconds Tx Cells No of cells to be transmitted Update Entry OAM Settings Select Mode OAM _F5 VCI Channel Displays the selected VCI channel of the OAM F5 Setting Table F5 Transmit Interval time Configures the time in ms for the interval to send F5 loopback cells OAM F5 Setting Table Click Test to view the OAM F5 results VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel When you test the OAM Configuration the F5 result is displayed as shown in Figure 4 6 9 1 and this may be a failure or successful OAM F5 result OAM F5 Ping Successful VPI VCI 0 35 Cells Tx 5 Cells Rx 0 Cells Not Rx 5 Max Resp Time l Min Resp Time 0 Avg Resp Time millisecs 0 Figure 4 6 9 1 Test Successful OAM F5 Ping Failed VPI VCI 0 35 Cells Tx Cells Rx 0 Calls Not Rx 5 Max Resp Time Min Reso Time 0 Avg Resp Timet millisecs 0 Figure 4 6 9 2 Test Failed 99 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in ADSL OAM F5 Test Page Field Description VPI VCI Displays the selected VPI VCI channel of the OAM F5 Setting Table Cells Rx Count of total number of received ATM cells Max Resp Time Displays the maximum response time in millis
21. Weight Dimensions Chipsets 4x PowerLED 4 x Link Active Status for Ethernet port 1 x Link LED for VDSL2 port 1x WPS LED AAA Store and forward Input Voltage 12 VDC Commercial grade power adapter u EMI Compliant FCC EMS Compliant CE mark Operating Temperature 0 C 50 32 F 122 F Fan less freee air ir cooling 20 C 70 C 4 4 F 158 F 10 to 90 non condensing About 0 44 Kg 184 x 158 x 104 mm 7 2 x 6 22 x 4 1 with 2dBi Antenna Lantiq VRX N ol Te AH Router Mode select This appendix describes how to select the router mode The wireless router default mode is router mode please refer to the following steps to select the router mode or switch mode 221 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Selecting the Router mode 1 For configuring the router mode settings click the LAN Settings link LAN gt LAN Settings on the left navigation bar Select Server as the DHCP Mode and click Apply at any time during configuration to save the information that you have entered A screen is displayed as shown in Figure C 1 DHCP Mode DHCP Server IP Pool Starting Address 192 fies fa 2 IP Pool Ending Address 192 168 ES 1254 Lease Time Halfhour Local Domain Name ldslgw antig com optional IP Address Reservation Click Here Figure C 1 DHCP Mode Server ee ee ee ne 2 Cl
22. as well as a representation of the WAN side 2 6 3 Run Demos and Tests The Ethernet tester may send data downstream as well as upstream It also receives the data in order to check the integrity of the data transmission Different data rates can be tested under different line conditions 2 6 4 Wireless Basics In recent years the market for wireless communications has enjoyed tremendous growth Wireless technology now reaches or is capable of reaching virtually every location on the surface of the earth Hundreds of millions of people exchange information every day via wireless communication products Anyone can bring a built in WLAN client Smartphone tablet or notebook into a meeting room for a conference without laying a clot of LAN cable or drilling holes everywhere Wireless LAN enables high mobility so WLAN users can simultaneously access all LAN facilities just like on a wired LAN as well as Internet access The wireless router is equipped with a wireless LAN interface compliant with the standard IEEE 802 11n protocol To boost its performance even further the wireless router is also loaded with an advanced wireless technology to lift up the data rate up to 300 Mbps You can finally smoothly enjoy a wide range of apps on your smart phone tablet or smart TV 15 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel E What is WEP Wired Equivalent Privacy WEP is an easily broken security algorithm fo
23. entry Click Delete for deleting the existing URL filtering entry 156 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 10 5 Parental Control For configuring the Parental Control click the Parental Control link Firewall gt Parental Control on the left navigation bar A screen is displayed as shown in Figure 4 10 5 Parental Control You can block access based on MAC addresses and Time of Day to certain client PCs on the LAN MAC Address Control a Disable de Deny All C Permit All MAC Address Control List mn ATT 7 Figure 4 10 5 Parental Control Configuration 157 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Parental Control Field Description MAC Address Control List licy 2 Click Add at any time during configuration to add the specified MAC address entry in the table Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 9 158 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 10 6 Application Server Settings For configuring the Application Server Settings click the Application Server Settings link Firewall gt Application Server Settings on the left navigation bar A screen is d
24. following connections Quick Configuration of default WAN connection to Service Provider s network WAN Setup x WARE Ove Default WAN Connection Setup Channel Vlanld 201 Excluded 2 3 4 5 2049 2050 2051 2052 2053 Connection Type PPPoE e Username Password Figure 4 1 2 Quick Setup WAN Setup When the user clicks on Quick Setup the WAN Setup tab is displayed as shown in Figure 4 1 2 1 The WAN Setup enables the user to configure the default WAN connection The user has to supply fields and the CPE device will take all necessary actions to ensure the default WAN is configured In case the WAN connection already exists in CPE device the same gets re created with newly supplied attributes from the user The default WAN Setup configuration shows the Bridged status 28 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Quick Configuration of default WAN connection to Service Provider s network Default WAN Connection Setup Channel Vlanld 201 Excluded 2 3 4 5 2049 2050 2051 2052 2053 Connection Type Bridged we Configure Figure 4 1 2 1 WAN setup Bridged The screen contains the following details Fields in Home page Field Description Channel Vlanld specify VLAN Id Reserved or internally used VLANs that cannot be configured in Quick WAN Setup are listed Click Configure to configure the default WAN connection setup 29 VC 400RTW VDSL2 Sl
25. i LAN Seftings E ER 7 Subnet Mask 255 M255 W255 fo UPnP Devices LAN Switch Port Setting MAC Address oo los lse kloz koo fos LAN Port Status ll Secondary level subnet Range L Enable ll Route d DHCP Mode Server Wireless gt rer Firewall gt DHCP Server NAT d IP Pool Starting Address 182 Miss E QoS gt Multicast gt IP Pool Ending Address 197 tbe 1100 eee Eases tive IPv6 gt Diagnostics WAN Setting Local Domain Name dsigw ydsl com optional Auto Detect Enable na WAN_Dynamic_ptmO FTM VLAN None Dhep Client lt a 4 1 1 Home After logging in successfully using the username admin the home page of wireless router is loaded in the web browser The user can also click Home on the left navigation bar The home page displays the information screen as shown in Figure 4 1 1 25 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel System gt Version Information tet p Software Version B 1 xDSL DSL Firmware version 9 4 8 0 0 6 5 4 4 5 1 2 b po z gt xDSL Information Connected Standard VDSL 304 Route Modem Status SHOWTIME SYNC i iss P E Default WAN Connection Wan Mode VDSL PTM NAT Link Status CONNECTED 005 IP Address 192 168 16 236 Multicast gt Connection Type Bridge IPsec DNS Server IPvb LAN Information Diagnostics gt IP Address 192 168 16 236 EEE er DHCP Mod
26. left navigation bar A screen is displayed as shown in Figure 4 14 3 DS Lite Configuration Because of IPv4 address exhaustion Dual Stack Lite DS Lite was designed to let an Internet service provider omit the deployment of any IPv4 address to the customers Customer premises equipment CPE Instead only global IPv6 addresses are provided Note To configure DS Lte on a WAN connection IPv must be enabled at IPv Setting page and native IPv must be enabled on that WAN connection at WAN Setting page General Settings Enable DS Lite tunnel u WAN Interface select interface i Configuration Modes Static DS Lite MTU optional Static Parameters DS Lite Remote IPv6 address DS Lite tunnel IP address IPv4 192 0 02 l Subnet Mask Lw4o6 Fort Range Valid 0 to 65535 Ex 40000 40000 4 rn 41000 WAN interface Configuration Mode Remote IPv6 address Tunnel IP IPv4 Figure 4 14 3 DS Lite Configuration 211 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in DS Lite Configuration Field Description General Settings Enable DS Lite tunnel To enable disable DS Lite functionality in CPE Modes to configure DS Lite tunnel on a WAN interface Currently Static Configuration Modes I Dynamic DHCPv6 option 64 and Lw406 DS Lite modes are supported Static Parameters IPv6 add
27. router via Web Browser The wireless router provides a built in HTML based management interface that allows configuration of the wireless router via Internet Browser Best viewed using Chrome or Firefox browsers In order to use the web browser to configure the device you may need to allow e Web browser pop up windows from your device Web pop up blocking is enabled by default in windows XP SP2 or above e Java Scripts Enabled by default e Java permissions Enabled by default Launch your web browser and input the IP address 192 168 1 1 wireless router in the Web page Following section user can find default username and password 23 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 1 Login The default username is admin password is admin too The password is changeable in Administrator Settings lt is advisable to change the administrator password for the security of your network Username admin Password CANCEL Figure 4 1 Login Password eo The wireless router default mode is Router mode Following screenshot is for default LAN settings and WAN settings 24 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel System gt LAN Settings Statistics xDSL You can configure LAN settings of CPE device such as LAN IP Address and DHCP configuration WAN gt LAN LAN ARP List h Primary IP Address LAND 192 168
28. sure the tab on the plug RJ 45 Terminal Blobk clicks into position to ensure that it is properly seated Do not plug a RJ 11 phone jack connector into the Ethernet LNE PHONE 3 port RJ 45 port This may damage the router Instead use js only twisted pair cables with RJ 45 connectors that conform to Ethernet standard Notes 1 Be sure each twisted pair cable RJ 45 Ethernet cable 3 does not exceed 100 meters 333 feet 2 We advise using Category 5 7 UTP STP cables for making Bridge or Router connections to avoid any confusion or inconvenience in the future when you attach high bandwidth devices 3 Use 24 26 gauge twisted pair phone wiring we do not 3 recommend 28 gauge or above 4 Be sure the phone cable has been installed before wireless router is powered on Figure 2 1 wireless router line ports straight connection 2 6 VDSL2 Application The router s line port supports 100Mbps 0 3km for data service across existing phone wiring It is easy to use and do not requires installation of additional wiring Every modular phone jack in the home can become a port on the LAN Networking devices can be installed on a single telephone wire that can be installed within a suitable distance Figure 2 2 12 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Phone Cable Ethernet Cable VDSL2 CO CPE Router leverages the extraordinary bandwidth pr
29. the check box to enable Click Apply for applying the configured DMZ Click Cancel to exit from this page without saving the changes 178 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 179 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 11 QoS You can view QoS on the left navigation bar of the wireless router CPE homepage The menu below includes the sub menus of AEREOS ALSTER Te and AECA IT Following are the options available under QoS as shown in Figure 4 11 QoS Settings Queue Config Class Contig Figure 4 11 QoS Options 180 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 11 1 QoS Settings For configuring the Quality of Service QoS Settings click the QoS Settings link QoS gt QoS Settings on the left navigation bar A screen is displayed as shown in Figure 4 11 1 QoS Setting Quality of Service settings for providing WAN upstream traffic prioritization in CPE Active WAN mode i Qos Enable 5 Disable Upstream QoS O Enable 2 Disable Downstream QoS Enable Disable 38021P Remarking O Enable 5 Disable The default DSCP Marking can be used to mark all the packets on WAN uplink that do not match any Classification entries of QoS Upstream Default DSCP marking m v WAN Fort Rate Limiter di PPA Session Acceleration Setting
30. to configure Host name can be used in place of IP address System Time Administrator Settings Web Settings Software Firmware Upgrade Host Name abckpe Configuration Settings Domain Name abe com System Log SSL Certificate Reset Figure 4 3 1 Host Name Configuration Fields in Host Name Configuration Description Enter the host name of the VDSL2 CPE This is used to address VDSL2 CPE by using this name instead of typing the IP address Maximum Characters 60 Host Name Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 38 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 3 2 System Time You can set System Time by connecting to a Simple Network Time Protocol SNTP server allows the Modem to synchronize the system clock to the global Internet The synchronized clock in the Modem is used to record the security log and control client filtering This page provides the time zone selection and NTP Network Time Protocol configuration Click the System Time link System gt System Time on the left navigation bar and a screen is displayed as shown in Figure 4 3 2 System System Time Host Name Config ata fe SE us the CPE dew to th System Time Connecting to a Simple Network Time Protocol SNTP server allows the CPE device to synchronize the system clock to t
31. will be a minimal charge to replace consumable components such as fuses power transformers and mechanical cooling devices The warranty will not apply to any products which have been subjected to any misuse neglect or accidental damage or which contain defects which are in any way attributable to improper installation or to alteration or repairs made or performed by any person not under control of the original owner The above warranty is in lieu of any other warranty whether express implied or statutory including but not limited to any warranty of merchantability fitness for a particular purpose or any warranty arising out of any proposal specification or sample We shall not be liable for incidental or consequential damages We neither assume nor authorize any person to assume for it any other liability 235 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel WARNING Y WARNING Warranty Void 1 DO NOT TEAR OFF OR REMOVE THE WARRANTY STICKER AS SHOWN OR THE WARRANTY IS VOID If Removed 2 WARRANTY VOID IF USE COMMERCIAL GRADE POWER ADAPTER IS USED AT HARSH ENVIRONMENTS 236
32. 050 2051 2052 2053 Connection Type Static IP w IF address Ann IL UL DL Subnet Mask Gateway Configure Figure 4 1 2 4 WAN setup Static IP 32 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in WAN setup Static IP Field Description Channel Vianld Specify VLAN Id IP Address Specify the IP Address of wireless router CPE s WAN link Specify the Gateway address of the wireless router CPE s WAN Click Configure to configure the selected WAN connection setup When WAN mode is other than ATM the corresponding web pages will be available in WAN setup Those web pages will not ask user for fields like ATM VCC etc eeeee eee ee ew ew we ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew ew m m et 33 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel WLAN Setup When the user clicks on Quick Setup the WLAN Setup tab is displayed as sho
33. 14 1 By default IPv6 is not enabled IPv6 Setting This web page alows to enable or disable the IPv6 capabilities on the CPE device MOTE The IPv6 related settings on other web pages will be effective only if IPv6 is enabled here Enable gt Disable Figure 4 14 1 IPv6 Setting The system wide IPv6 feature can be enabled or disabled through this web page Select the appropriate control and click the Apply button for making the change effective in CPE All other IPv6 features in CPE will be in effect only when this global IPv6 is enabled in CPE 207 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Fields in IPv6 Setting IPv6 Setting Enable IPv6 functionality in CPE Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 208 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 14 2 6RD Configuration The wireless router supports IPv6 transition mechanism defined in 6RD RFC 5569 For configuring the 6RD configuration click on the 6RD configuration link IPv6 gt 6RD Configuration on the left navigation bar A screen is displayed as shown in Figure 4 14 2 6RD Configuration 6rd is a mechanism to facilitate IPv6 rapid deployment across IPw4 infrastructures of Internet service providers ISPs General Settings Enable 6rd t
34. 2 3 Ethernet based interface Click Perform ARP Scan to ensure the ARP entries connected to the CPE 102 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 7 2 LAN Settings For configuring the LAN interface click the LAN Settings link LAN gt LAN Settings on the left navigation bar In case the Secondary level subnet Range checkbox is checked some additional data and options will be on display A screen is displayed DHCP Server mode as shown in Figure 4 7 2 LAN Settings You can configure LAN settings of CPE device such as LAN IP Address and DHCP configuration IPvA Hii IP Address Subnet Mask 1255 233 MAC Address Secondary level subnet Range Secondary IP Address Secondary Subnet Mask DHCP Mode IP Address Reservation Click Here Apply Figure 4 7 2 LAN Settings DHCP Server 103 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in LAN Settings Field Description IP Address Used to enter the LAN interface IP Address of CPE device MAC Address MAC Address of LAN bridge device lt can be overridden by specifying the user supplied MAC address here Secondary IP Address This is to enter the secondary IP address To choose the mode of DHCP in wireless rou
35. 2 kompatibel Fields in WPA PSK WPA2 PSK Settings Cont d Description Personal Specify the Pre shared key NW Radius Remote Authentication Dial In User Service RADIUS is a security authentication client server protocol that supports authentication authorization and accounting which is widely used by Internet service providers It is the most common method of authenticating and authorizing dial up and tunneled network users The built in RADIUS client feature enables the router to assist the remote dial in user or a wireless station and the RADIUS server in performing mutual authentication lt enables centralized remote access Authentication Type authentication for network management WPA2 Pre Authentication Enable Radius Server IP 0 Radius Server Port 11812 Group Interval 13600 Shared Key ERTEILT Display Hide Shared Key Select Algorithm Type for the chosen Encryption tyoe Choose the WPA algorithm Algorithm Type 2 YP N 9 TKIP or AES Pre shared Key The keys can be entered in ASCII Type the key you wish to use 132 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 9 3 WMM Settings WMM is an abbreviation of Wi Fi Multimedia It defines the priority levels for four access categories derived from 802 1d prioritization tabs The categories are designed with specific types of traffic voice video best effort and low priority data There are four accessing ca
36. Access Point Telekom VDSL2 kompatibel Encryption Type Basic Authentication Type Shared w Algorithm Type WEP Key Index Key1 Encryption Level 64 Bit WEP Key Type ASCII Key WEP Key 1 wep_1 WEP Key 2 wep_2 WEP Key 3 lwep_3 WEP Key 4 wep 4 lf you choose WEP as the security configuration you have to specify encryption key WEP Key 1 WEP Key 4 All wireless devices must support the same WEP encryption bit size and have the same key Four keys can be entered here but only one key index can be selected at a time The keys can be entered in ASCII and HEX key Choose the key you wish to use by using the Default Key drop down list Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes Encryption Type WPA PSK WPA2 PSK If you choose WPA PSK WPA2 PSK as the security configuration you have to specify WPA mode algorithm and pre shared key 130 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Encryption Type WPA PSK Authentication Type Algorithm Type WPA WPA2 Settings Personal Settings Pre Shared Key EIFEL Display Hide Passphrase PSK Fields in WPA PSK WPA2 PSK Setting Field Description security Selection 131 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL
37. DSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Fields in Snooping Field Description en Enable or Disable the IGMPv3 IGMPv2 Snooping functionality nooping Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 199 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 12 3 Advanced Settings For configuring the advanced settings on Multicast features click the Advanced Settings link Multicast gt Advanced Settings on the left navigation bar A screen is displayed as shown in Figure 4 12 3 IGMP Advanced Settings Configurable parameters to tune IGMP performance Fast Leave dl Group Query Response Interval d ao 1 125 seconds Group Last Member Query Interval a 1 3600 seconds Group Last Member Query Count E o 1 10 Figure 4 12 3 Multicast Advanced Settings 200 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Multicast Advanced Settings Field Description IPv4 IPv6 Choose the appropriate tab to configure either for IPv4 or IPv6 Group Query Interval Specify Group Query Interval in range of 1 3600 seconds alas Group Last Member Query Interval in range of 1 3600 se
38. ERESTEERETRSEREERRERERRSRREREREREREERRESDERRTTRHREEERTEREIEEEHEERERTERRERIEHEEISEHERTRHEREEEERTTEERIEHTSERTREEETSEEIEEETSEEEEENE 3 Check the power plug by plugging in another that is functioning properly Check the power cord with Solution another device Check the terminal block make sure to fasten the power cord lf these measures fail 3 to resolve the problem have the unit power supply replaced by a qualified distributor 3 poo oe mn eee oe mn eee oe oe En oe mn ee En oe ee oe an ee ow oe En ee ow oe En ee En oe ow ee En oe En ee En oe ow ee En Ana En ee En ana En ee En ew ee e we En en re ew ee ne a En ew ee En nam En ee En en ee En nam En re SD ODED En en En nam En ee En nam En ee ne En ee ne En en en ee ne En er En nam En ee En nam En ee en ee En en ee En e ae aeaa oe an ee we we eon Note Please refer to the power status table to check power input status Section 3 3 3 Network interface ex a network adapter card on the attached device network cable or switch port 3 is defective 2 1 Power off and re power on the VDSL2 router 2 2 Verify that the switch and attached device are power on 3 2 3 Be sure the cable is plugged into both the switch and corresponding device Solution 2 4 Verify that the proper cable type is used and its length does not exceed specified limits 2 5 Check the router on the attached device and cable connections for possible defects 2 6 Make sure that the phone wire must be connecti
39. Enable or Disable PPA Session Acceleration PPA Session Acceleration Enable Disable Figure 4 11 1 QoS Settings 181 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in QoS Settings Field Description Active WAN mode Informative Parameter to show current WAN mode being used This selection will enable the QoS feature Upstream QoS This selection will enable the upstream Qos Downstream QoS This selection will enable the downstream Qos 8021P Remarking Enable Disable This will enable disable global 8021P Remarking WAN Port Rate Limiter Check box for limiting physical port rate limit on WAN upstream link PPA Session Acceleration Setting Hardware Acceleration based on Protocol Processing Engine PPE of Lantiq Acceleration To enable disable the session acceleration feature Click Apply for applying the QoS setting changes into system Click Cancel to exit from this page without saving the changes 182 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel DSCP comparison table example Reference only IP Precedence 3 Bits DSCP 6bits Name Value Bits Fer D me ep er DSCP en DSCP Decimal ToS Decimal Behavior em ae Runtime 0 000 Default __ Default Priority 1 001 AF Immediate a AF41 NGN 3G Signaling 100 010 To 136 en Override 4 2 Medi
40. Field Description Enable DDNS support Check box to enable DDNS support in CPE DDNS Server Dynamic DNS Server Provider User Name Registered user name with DDNS service provider Click Apply for applying the DDNS changes into system Click Cancel to exit from this page without saving the changes 96 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 9 OAM Configuration This page provides ATM F5 based OAM test Hence the settings are valid only for ATM based WAN For configuring the ADSL OAM settings click the OAM Configuration link WAN gt OAM Configuration on the left navigation bar This release supports only F5 type of OAM tests as shown in Figure 4 6 9 ADSL OAM Configuration OAM Setting Table No VPI VCI Loopback TX Cells Update Entry 1 0 35 Disable 600 5 a l iin 2 0 0 Disable 600 I Q OAM Settings Select Mode OAM_F5 VPI Channel lo VCI Channel 33 Select Method PING Loopback _ Enable Transmit interval time 500 Al 60 10000 Milliseconds Number of Tx Cells EB A 1 100 Figure 4 6 9 ADSL OAM F5 Test 97 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in ADSL OAM F5 Test page Description This table displays all active connections with following OAM parameters information No Number VPI
41. Figure 4 8 1 1 Static Routing IPv6 Tip 119 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 8 2 RIP Support The RIP support for enabling dynamic routes in CPE may be present in some of pre built packages For enabling the RIP support click the RIP Support link Route gt RIP Support on the left navigation bar A screen is displayed as shown in Figure 4 8 2 Dynamic Routing The dynamic routing feature of the router can be used to allow the router to automatically adjust to physical changes in the network s layout The router uses the dynamic RIP protocol It determines the route that the network packets take based on the fewest number of hops between the source and the destination The RIP protocol regularly broadcasts routing information to other routers on the network Dynamic Routing Enable Disable Listen Mode RIP2 E Supply Mode RIP2 RIPng RIPng O Enable 2 Disable a E A Figure 4 8 2 Dynamic Routing 120 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Dynamic Routing Field Description Dynamic Routing To enable or disable the Dynamic Routing RIP in CPE To configure the supply mode of RIP to Disabled 9 RIP1 RIP2 Supply Mode Click Apply at any time during configuration to save the information that you have entered
42. N Tire BIC gt Lee Ug a AA VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 3 9 Reset To reboot the system click Reset link System gt Reset on the left navigation bar A screen is displayed as shown in Figure 4 3 9 e System Reset CPE device Host Name Config System Tim In the event that the CPE device stops responding correctly or in some way stops functioning you can perform a reset To perform the PUCH ES SINE reset click on the Reset button below You will be asked to confirm your choice The reset will be complete when the power light stops Administrator Settings blinking Some times the device may be corrupted by faulty configurations in such a state you can bring the CPE device back to factory ia default configuration settings by clicking the Factory Reset button By pressing Factory Reset all user configurations are replaced with Web Settings factory default configuration settings Software Firmware Upgrade Configuration Settings yan toa Ga GH Reset SSL Certificate centre an Help Figure 4 3 9 Reset Click Reset to reboot the system This does not change the configurations existing in system Click Factory Reset to reset the device configuration to factory defaults configuration This operation will result in saving the current configuration and reverted back to factory shipped configuration When Reset or Factory Reset is clicked a confir
43. N ne nee ee ETE A ee sees 25 A A 27 A AR A 36 o e e eee ee eer 37 A Host Name AAN da tata nta 38 AS e iu AA kctoe gauss een ae Re arena 39 4 3 3 Administrator Settings User Account Management ccccceccccseececeeeceeeeececeeceeseeeeeseceeseeeesseaeessauseeeseeeesseueesseeeesseeesaeeeeeas 41 o e o A Pe 43 43 9 9011 Elia ci AAA e o ro o e 44 oo ae 45 AS Po ee ene ee eee eee 48 1 3 8 9 A A o 51 E E o Pe NEE E A A A E EE E E E E 52 SSIS SIAUSUCS a E E ee A E EEE 53 aA TUAN AP E E E E E E E E 54 AAL INAN A A 56 AO ESO DO tt tdi 58 o An 59 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel eo O een eee ene ee 61 A621 WAN MOGE OCCO UO saren ee 62 4 672 AUO Detect Selling ai eco rA aia 64 aG SWAN G akg alate aiile 8 e211 Onon nnn nnne nnana Eaa cere eee ee eee ere 67 2 64 VEAN HG Maine COnmiQuir atl diia dd 71 A WAN SEMN ed diia ld dll 74 An o eee eee ere eee ere rere ec rere 89 4 T DONG ene eer eee oe E eae rete arte nee ae fete ees eet See eee ten eee ee ee eee ene meee ere neer eee eee rer rey ere ere eee ree eee eee rere 93 4C S DDNS a canes iS A eft hd ae tl seal id DG wed E ERE 95 ADAM CONIL UOT ee aiii 97 AT eo 0 EAN avaricia eee ee ne een eisen 101 A RSI PAPA AA A PP P Ale ee se een 102 A EAN Sellings o eee eee ere 103 AE DEVICES Ki ae esse ee esse 113 4 A EAN Switch PO Selling ini 114 Ao LANEROS US nad 115 4 8 SEIEEL FOULS rd AS AAA
44. NAT Settings on the left navigation bar A screen is displayed as shown in Figure 4 11 1 NAT Settings Network Address Translation NAT allows multiple users at your local site to access the Internet through a single public IP address or multiple public IP addresses NAT can also prevent hacker attacks by mapping local addresses to public addresses for key services such as the Web or FTP Enable Disable Figure 4 11 1 Network Address Translation NAT Settings The screen contains the following details Fields in Network Address Translation Field Description NAT Settings Used to Enable or Disable the Network Address Translation feature Click Apply for activating or deactivating the NAT feature Click Cancel to exit from this page without saving the changes 164 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 11 2 Virtual Server For configuring the virtual server click the Virtual Server link NAT gt Virtual Server on the left navigation bar A screen is displayed as shown in Figure 4 11 2 Virtual Server You can configure the CPE device as a virtual server so that remote users accessing services such as the Web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses In other words depending on the requested service TCP UDP port numbers the CPE device redirects the external se
45. P Address Source Netmask Source Port 3671 In 13671 URL Filtering Parental Control Destination IP Type SUBNET v DIDPRCHHOR SOYO SAINS Destination IP Address 192 168 1 0 ACL n NAT gt Destination Netmask 255 255 255 0 EL Destination Port 3671 113671 Multicast gt y Ingress Interface v IPsec gt iPv6 gt Egress Interface v Diagnostics gt i Source MAC Address i Enable Quick Setup Home K Logout SS Cancel 152 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Configure example Firewall Packet Filtering Items Setting argument Action Protocol TCP Example Source port 3671 3671 192 168 1 0 Example it means 192 168 1 0 192 168 16 255 Destination port 3671 3671 Apply Button Click it Packet Filtering Destination IP Address Statistics gt Configure packet filter rule for denying the packets conforming to it wales ar Source Source Source Destination IP og Protocol Ingress Egress MAC Enable IP Port Interface Interface Ad un Firewall Firewall Setting IPv6 Firewall Setting Packet Filtering URL Filtering Parental Control 3671 3671 192 168 1 0 24 3671 3671 Application Server Settings ACL Packet filtering complete 153 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Enable Firewall function
46. Parameter AIFSN Arbitrary Inter Frame Spacing Number Admission Control Enable Disable WLAN Flow admission control ECWmin Exponential of Contention Window minimum Parameter AIFSN Arbitrary Inter Frame Spacing Number AckPolicy Acknowledgement Policy Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 134 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 9 4 WPS Settings WPS Wi Fi Protected Setup provides an easy procedure to make a network connection between wireless stations and wireless access points with the encryption of WPA and WPA2 If you choose WPS as the security configuration you can press Start WPS PIN and Start WPS PBC to complete the wireless connection When you click WPS Settings link Wireless gt WPS Settings on the left navigation bar a screen is displayed as shown in Figure 4 9 4 WLAN WiFi Protected Setup WPS WPS is used to easily add devices to Wireless network using a PIN or a push button The devices must support WPS capability in order to be configured by this method SSID NVC WPS Configuration WPS Enable Apply Changes Personal Identification Number PIN Method Please enter the PIN from your wireless device and push the Connect button Enter Client Device Pin PARECE Push Button Configuration PBC Me
47. RUBYec Deutschland GmbH Networking amp Communications Kompetenzzentrum fur Richtfunk und Standortvernetzung do Kleestr 27 52396 Heimbach eee eS a orion P 02446 8095610 F 02446 8095619 AA poo an seteneenvonaugnnennvensuancnusvansasunaesneess AAA LE TT Eee t i ae En 1 See a AA Lores anne Een K gt ie ad B F ma til Managed Wireless VDSLZ 2 F outer nz USER S MANUA a ar 7 VC 400RTW a p VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Foreword VDSL2 Router solution Attention eww mmm ww wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn Sw wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn nw wn wn wn wn wn wn wn wn wn wn wn wn wn ww wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn a wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn a ow wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn wn a Sow a wn wn wn wn wn wn wn aaa Managed wireless VDSL2 router is a wireless router that leverages the extraordinary bandwidth promise of VDSL2 technology and compliant with the IEEE 802 11n standard It can enhance wireless speeds up
48. The firewall has to be enabled in order to start the packet filter BA System gt Firewall Setting Statistics 3 ET Firewall gt Disable Firewall Setting The CPE device provides extensive firewall protection against a wide array of common hacker attacks This is done by restricting connection parameters to limit the risk of intrusion IPv6 Firewall Setting Packet Filtering URL Filtering Parental Control Application Server Settings ACL Note All the setting arguments above are examples please follow the on site environment to set 154 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 10 4 URL Filtering URL Filtering is used to block the access to specific URLs to the web users by adding them to the list in the URL Blocking web page For configuring the URL Filtering click the URL Filtering link Firewall gt URL Filtering on the left navigation bar A screen is displayed as shown in Figure 4 10 4 URL Blocking This web page allows you to Block URLs on the CPE device A DomainName elec Nothing is blocked Figure 4 10 4 URL Blocking 155 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in URL Blocking Field Description URL of the domain that needs to be blocked For example www google com tw Click Add for adding a new URL filtering
49. VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Safety Warnings For your safety be sure to read and follow all warning notices and instructions before using the device 0000o oo o 9 4 DO NOT open the device or unit Opening or removing the cover may expose you to dangerous high voltage points or other risks ONLY qualified service personnel can service the device Please contact your vendor for further information Use ONLY the dedicated power supply for your device Connect the power to the right supply voltage 110V AC used for North America and 230V AC used for Europe wireless router supports 12 VDC power input Place connecting cables carefully so that no one will step on them or stumble over them DO NOT allow anything to rest on the power cord and do NOT locate the product where anyone can work on the power cord DO NOT install nor use your device during a thunderstorm There may be a remote risk of electric shock from lightning DO NOT expose your device to dampness dust or corrosive liquids DO NOT use this product near water for example in a wet basement or near a swimming pool Connect ONLY suitable accessories to the device Make sure to connect the cables to the correct ports DO NOT obstruct the device ventilation slots as insufficient air flow may harm your device DO NOT place items on the device DO NOT use the device for outdoor applications directly an
50. WAN WAN IPv6 Configuration Description This option allows to select following modes of IPv6 configuration Configuration Modes Stateful DHCPv6 IA_NA and IA_PD SLAAC Address Configuration with DHCPv6 IA_PD This option allows to configure different DUID DHCP Unique Identifier types DUID Type Type 1 LLT Link Bal Time Type 2 EN Enterprise Number Type 3 LL Link Layer IANA option represents IPv6 address and parameters related to the same being accepted by IANA ID DHCPv6 clients IANA is the Identity Association for Non Temporary Addresses option This Identifier has to be configured when Stateful DHCPv6 configuration mode is selected APD options represent one or more IPv6 prefix and parameters related to it IAPD is the Identity IAPD ID Association for Prefix Delegation This identifier needs to be configured in both Stateful DHCPv6 and SLAAC DHCPV6 configuration modes This parameter is called Site Level Aggregation Identifier This identifier is used to configure the subnet for DHCPv6 client configuration Commit Handshaking will happen with two DHCPv6 messages Default WAN This option allows configuring default route for relevant WAN mode of this WAN connection Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompat
51. _config Nov 29 23 34 54 none daemon debug mini_httpd 1663 ifx_get_FirmwareVer 1439 fw version 5 4 8 0 0 6 5 4 4 4 0 1 5 4 8 0 0 6 5 4 4 4 0 1 length 49 r Nov 29 23 44 23 none daemon debug mini_httpd 1663 ifx_get_FirmwareVer 1439 fw version 5 4 8 0 0 6 5 4 4 4 0 1 5 4 8 0 0 6 5 4 4 4 0 1 length 49 Nov 29 23 44 23 none daemon info mini_httpd 1663 192 168 16 9 File Nov 29 23 44 27 none daemon info mini_httpd 1663 192 168 16 9 File Nov 29 23 44 30 none daemon info mini_httpd 1663 192 168 16 9 File Nov 29 23 44 30 none daemon info mini_httpd 1663 192 168 16 9 File Nov 29 23 44 31 none daemon info mini_httpd 1663 192 168 16 9 File Nov 29 23 44 31 none daemon info mini_httpd 1663 192 168 16 9 File A ze GL GL GEL favicon ico favicon ico favicon ico favicon ico favicon ico favicon ico Figure 4 3 7 1 View System Log returned failure is protected is protected is protected is protected is protected is protected For the ease of readability the log messages of different levels are using different colors all the debug messages are shown in green colored text Click Download to save the file in Host Computer Click Clear to clear the log from the system Click Refresh to get the recent log Click Back to go back to System Log page 9 50 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 3 8 SSL Certificate
52. a screen is displayed as shown in Figure 4 7 2 5 Prefix Delegated br 2001 db8 36 500 64 Figure 4 7 2 5 Prefix Delegated view Click Back to exit from this page 112 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 7 3 UPnP Devices List For discovering the UPnP Devices in LAN network click the UPnP Devices link LAN gt UPnP Devices on the left navigation bar A screen is displayed as shown in Figure 4 7 3 UPnP Devices List The UPnP Devices list allows you to see all UPnP devices that are discovered by the CPE 192 168 16 207 ADSL Router InternetGateywayDevice 23300001 bfde 11d3 832c 00056e020010 192 168 16 254 D Link Internet Gateway Device 0015E909 A59E D317 C798 0000C0A810FE Figure 4 7 3 UPnP device list The screen contains the following details Fields in UPnP Device List Field Description J 5 m E p ny PEN A d F Jev vil eS Click Refresh to view a new UPnP devices list 113 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 7 4 LAN Switch Port Setting For discovering the All LAN Port Setting in LAN network click the LAN Switch Port Setting link LAN gt LAN Switch Port Setting on the left navigation bar A screen is displayed as shown in Figure 4 7 4 All LAN Port Setting You can specify the ethernet ports setting Users can choose Auto 10M 100M 1000M 10M Full Half or 100M Full Halr m
53. ave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Quick Configuration of default WAN connection to Service Provider s network WE Eccl WLAN Se tur Default WAN Connection Setup Channel Wlanld 1207 J Excluded 2 3 4 5 2049 2050 2051 2052 2053 Connection Type Dynamic IP Figure 4 1 2 2 WAN setup Dynamic IP The screen contains the following details Fields in WAN setup Dynamic IP Field Description Channel Vlanld Specify VLAN ld Click Configure to configure the selected WAN connection setup 30 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Quick Configuration of default WAN connection to Service Provider s network WAN setup Ma Default WAN Connection Setup Channel VlanId 201 Excluded 2 3 4 5 2049 2050 2051 2052 2053 Connection Type PPPoE w Username fs Password Configure Figure 4 1 2 3 WAN setup PPPoE The screen contains the following details Fields in WAN setup PPPoE Field Description Channel Vlanld Specify VLAN ld Username Enter a valid Username 31 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Click Configure to configure the selected WAN connection setup Quick Configuration of default WAN connection to Service Provider s network WAN Setup Default WAN Connection Setup Channel Vland 1204 Excluded 2 3 4 5 2049 2
54. by tour ISP WAN IP 192 168 16 204 Example ISP Gateway Address 192 168 16 1 Example Apply Button Click it System gt WAN Setting Statistics gt xDSL gt Auto Detect Enable WAN gt Default Auto Detect Config O PTM VLAN N Fix IP WANIPO VLAN None WAN Channel Config VLAN Channel Config WAN Setting WAN Status DNS DDNS OAM Configuration WAN setting complete 148 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel LAN Setting LAN Settings You can configure LAN settings of CPE device such as LAN IP Address and DHCP configuration xDSL gt IP Address Firewall gt Subnet Mask NAT MAC Address econdary level subnet Range C Enable Pv6 gt Diagnostics Logout Lease Time One day v Local Domain Name dsigw com optional IP Address Reservation Click Here a ep Ay ne Configure example LAN gt LAN Settings Items Setting argument Action IP Address LAN IP 192 168 1 204 Example MAC Address wireless router mac address Auto detect IP Pool Starting Address 192 168 1 30 DHCP IP pool example Apply Button 149 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel DNS Setting A System Domain Name System DNS Statistics xDSL A Domain Name System DNS server translates hostnames or domain names to IP addresses Most ISPs provide a DNS server
55. conds 201 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 13 IPsec When clicking the IPsec on the left navigation bar of the wireless router CPE homepage The menu below includes the sub menu UMAN The following option Tunnel Mode is available under IPsec as shown in Figure 4 13 iPsec Tunnel Mode j Figure 4 13 IPsec Option 202 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 13 1 Tunnel Mode When you click the Tunnel Mode link IPsec gt Tunnel Mode on the left navigation bar a screen is displayed as shown in Figure 4 13 1 IPsec Tunnel Configuration On this page you can configure diferent IPsec tunnels Figure 4 13 1 IPsec Tunnel Configuration When you click Add button in the IPsec Tunnel Configuration page a screen is displayed as shown in Figure 4 13 1 1 203 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Tunnel Name Add IPSec Tunnel Configuration a AUTH_METHOD Prefixed Key v FSK Secret IKE Mode ikev v WAN Interface My Subnet Feer Address Feer Subnet WANPPP4 Hk TT IT 18 Y Enable IKE Cipher IKE Hash IKE DH Group modp1536 ESP Cipher aes128_cbc ESP Hash shal Key Lifetime 50 Minutes Retry 0 means always retry Figure 4 13 1 1 Add IPSec Tunnel Mode Configuration 204 VC 400RTW
56. creen is displayed as shown in Figure 4 7 2 1 this is used for the reservation of IP address of client s MAC address in DHCP server IP Reservation IP reservation Allow static IP address assignment by DHCP server for specified MAC address a a aceon 7 SAS a n Figure 4 7 2 1 IP Reservation 106 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in LAN Settings Field Description Host Name Host Computer name MAC Address MAC address of Host computer for which static IP reservation is needed To add this IP reservation entry Click Apply to save the changes that you have entered Click Cancel to exit from this page without saving the changes 107 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The following pages describe the LAN Settings for IPv6 LAN Settings IPv6 Tab If IPv6 functionality is enabled through Advanced Setup gt IPv6 then LAN Settings web page also presents IPv6 tab Based on the Auto Configuration Mode the following screens are displayed as shown in Figure 4 7 2 2 Figure 4 7 2 3 and Figure 4 7 2 4 LAN Settings You can configure LAN settings of CPE device such as LAN IP Address and DHCPw configuration Gr tay IPv6 Address fc00 1 E 54 Auto Configuration Mode Statele
57. cscercesecrsersceeseesceesareeeeserseresanseseaevansneesaneerseaneaneeeseas 216 APRENDIDOS PRODUCT SPECIFICATION occooiocccoconononononononononononono nono nono nono no nono nono c arcano 219 APRENDO ROUTER MODE SELECT cnccccccoconononononononono nono nono nono nono nono nono n canon 221 APPENDDOD VDSL2 CO ROUTER WIRELESS ROUTER COMPATIBILITY TABLE 225 APRENDIDO TROUBLESHOOTING ccccococococonccononononononononono nono non conocer 227 APRENDIDA COMPLIANCE INFORMATION ccecceecceccecscerceeesersercceesereceeseeseeesarsrecarsaeseeevareseesaneeeesaneersereas 233 WARRANTY ccceccescceesceerceecceseceerceaeceaeceaeecaeeeasseauecaevensvensversvenevensvescetevarecrevarevaeeveevaueeesniesersversvereverevsnevsieentens 235 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel edf Tol Unpacking Information 1 1 Check List Thank you for choosing Ruby lech VDSL2 wireless router Before installing the router please verify the contents inside the package Package Contents a tdt a ee ee u nannte nn nn nn nn nn nn nn nn nannten nn nn nn 1x Managed VDSL2 Accessory Kit 1 x DC12V Power Adapter VC 400RTW Router Notes 1 Please inform your dealer immediately for any missing or damaged parts If possible retain the carton including the Original packing materials Use them to repack the unit in case there is a need to return for repair 2 If the product has any is
58. d Access Point Telekom VDSL2 kompatibel 4 12 1 Proxy Settings For configuring the Multicast proxy settings in CPE click the Proxy Settings link Multicast gt Proxy Settings on the left navigation bar A screen is displayed as shown in Figure 4 12 1 Proxy This page allows the user to configure the CPE to provide multicast proxy functionality Enable IGMP Proxy Enable MLD Proxy al Figure 4 12 1 IGMP Proxy 196 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in IGMP Proxy Field Description dond di Enable or Disable the IGMPv3 IGMPv2 Proxy functionality Select one of the WAN interfaces from the drop down menu on which Multicast Proxy functionality to be enabled Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 197 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 12 2 Snooping Settings For configuring the Multicast Snooping settings click the Snooping Settings link Multicast gt Snooping Settings on the left navigation bar A screen is displayed as shown in Figure 4 12 2 Snooping This page allows the user to configure the CPE to provide multicast snooping functionality Enable IGMP MLD Snooping Figure 4 12 2 IGMP Snooping 198 VC 400RTW V
59. d make sure all the connections are indoors or have waterproof protection place Be careful when unplugging the power because it may produce sparks Keep the device and all its parts and accessories out of the reach of children Clean the device using a soft and dry cloth rather than liquid or atomizers Power off the equipment before cleaning it This product is recyclable Dispose of it properly VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel TABLE OF CONTENTS FOREWORD VDSL2 ROUTER TON renacido 1 SAFETY WARNIN Osa ter 2 EME as 8 CHAPTER INSTALLING THE ROUTER cocccocccocccononononononononononnncono nono nononono nono nono ronca nenas 9 lo El cl AA Ro E EEE AAA 9 2 2 PrE Inslallallon EQUINOS aia ee AAA RAR aid 9 AA o PPP o samen sdavinnsseeedauendnesanenceedaeesceseae 10 22 GONNE CURA IM FLOWER E aaa ee oda ld ee era ee ee 11 20 OMe Cita me RJ II Ad PONS re otero epa 11 AA oO ajateu ee ieee cash EE esse 12 CHAPTERS HARDWARE DESCRIPTION 0 00 ecceccecececceececesecesecerseeecaeeeaeecauecauseauseaeseaeseaueeeeveresseevsnevseevneeteees 17 o Uist ree ees eee neh cepacia ee tence eee LEE acunereeetadeuenaewaewnecenerens 18 92 PLORLINOIC ALONG cri re 18 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel DOR A Pan aras pololo Re 20 GRARTERM CONFIGURING THE WIRELESS ROUTER VIA WEB BROWSER cecceccseseeesserseseeeseeseeeseeees 23 A o A 24 AST O
60. d through the ATM tab Auto Detect Enable To enable Auto Detect VPI VCI Virtual Path Identifier and Virtual Channel Identifier Link type Shows AAL5 Link type for ATM VCC values such as EoATM IPoATM PPPoATM IF Name ATM Channel interface name in system 68 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel When you click Add inside the WAN Channel ATM tab a screen is displayed as shown in Figure 4 6 3 2 WAN ATM VCC Creation VC Channel Name ee VPI VCI 032 0 255 32 65535 Encapsulation Mode LLCISNAP Link type LINK_TYPE_EOATM oy QoS Mode UBR wl Peak Cell Rate D calls sec Cell Delay Variation jitters D Figure 4 6 3 2 WAN Channel Configuration ATM VCC Creation 69 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in WAN Channel Configuration Field Description VC Channel Name User specified VCC Name Encapsulation Mode Encapsulation Mode for this VCC from dropdown LLC SNAP or VCMux mode QoS Mode Quality of Service for ATM VCC Available options are UBR CBR rt VBR nrt VBR and UBR Cell Delay Variation Cell Delay Variation specified in terms of jitters Click Add to save the information that you have entered Click Cancel to exit from this page without saving the changes 70 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Poi
61. dio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 The equipment and the receiver should be connected to outlets on separate circuits 4 Consult the dealer or an experienced radio television technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 233 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel lf this telephone equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required But if advance notice isn t practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe it is necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the proper functioning of your equipment If they do you will be notified in advance in order for you to make necessary modifications to maintain uninterrupted service This equipment may not be used on coin service provided by the telephone company Connection t
62. disable acceleration for this classifier This is the Queue Identifier to be associated with this classifier rule This is presented in dropdown for associating with this classifier entry Ingress Interface Packet Input Source for classified flow Queue Name Classifier Type Type of Classifier Multi Field Classifier MFC or DSCP or 802 1p based Hwang eomirg VIAN VLAN Id Incoming VLAN id Source MAC Source MAC classification Source MAC Mask Mask bits for Source MAC Destination MAC Destination MAC classification 193 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel L3 Protocol Dropdown to select IPv4 IPv6 Netmask Mask bits for Source IP Netmask Mask bits for Source IP source Port Range Start and end source port range Order Classification order Click Apply for applying the changes Click Cancel to exit from this page without saving the changes 194 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 12 Multicast You can view Multicast on the left navigation bar of the wireless router CPE homepage The menu below includes the sub menus Of Ja S ZI he SIS EAH and Eine Following are the options available under Multicast as shown in Figure 4 12 Multicast gt Proxy Settings Snooping Settings Advanced Settings Figure 4 12 Multicast Options 195 VC 400RTW VDSL2 Slave Modem Router mit Switch un
63. dress 192 168 16 236 IPsec Connection Type Bridge IPv6 DNS Server Diagnostics gt aoe IP Address 192 168 156 236 Quick Setup DHCP Mode Relay Agent Home Ethernet PHY Port Status Logout PORT 1 Link Down _ PORT 2 Link Down PORT 3 Link Up 100Mb s Full Duplex PORT 4 Link Down WLAN Information Radio 1 Down Radio 2 Down Figure 4 2 Select the Menu Level wireless router 36 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 3 Select SYSTEM Select the SYSTEM The menu below will be used frequently It includes the sub menus of LERNER nile System Time Administrator Settings Web Settings Software Firmware Upgrade System Log SSL Certificate and Reset A screen is displayed as shown in Figure 4 3 System Host Name Config system Time Administrator Settings Web Settings Software Firmware Upgrade Configuration Settings system Log SSL Certificate Reset Figure 4 3 System Setup 37 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 3 1 Host Name Configuration To configure the host name of wireless router you have to enter host and domain name Click the Host Name Config link System gt Host Name Config on the left navigation bar A screen is displayed as shown in Figure 4 3 1 Ea System gt Host name Host Name Config aN Enter the host name for the CPE device and the domain name you want
64. e Disable Acceleration Queue Name Classifier Interface Ingress Interface Classifier Type Rate Control Enable Rate Limit Outgoing DSCP Incoming DSCP C m m det_queus u gt DSCP Based v Cancel Figure 4 11 3 1 Add Modify a Classifier Rule DSCP Based 191 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Classifier Type MFC Based v a Rate Control Enable Rate Limit Outgoing DSCP Incoming DSCP Incoming 802 1P wl Outgoing 802 1P a C Exclude Source MAC Mask _ Exclude Destination MAC Mask VLAN Id Source MAC Destination MAC Exclude L3 Protocol IPv4 v J Exclude Lt l Netmask Exclude AAA Netmask Exclude L Exclude Source IP Destination IF L4 Protocol Source Port range R Exclude Destination Port range la Exclude Order Last Heb Figure 4 11 3 1 Add Modify a Classifier Rule MFC Based 192 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Add Modify a Classifier Rule Field Description Classifier Name This is the name of Classifier This is a Unique identifier for an instance of classifier rule Enable This is used to enable or disable the QoS Classifier entry Classifier Interface This is used to select upstream downstream classifier Disable acceleration This is used to
65. e E Private IP lo lo lo lo Remote IP lo jo lo o optional Public Port Range 1 de Private Fort Range 4 a Enable WAN Interface co Figure 4 11 2 1 Virtual Server Add 168 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Virtual Server Add Field Description Application Name Specify Application name from dropdown or custom name for Virtual Server rule Private IP Specify Private IP address of Virtual Server rule Public Port Range Specify Public Port range Enabled To enable the specified entry of the virtual server tick on check box Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 169 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 170 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 11 3 Port Triggering For configuring Port Triggering click the Port Triggering link NAT gt Port Triggering on the left navigation bar A screen is displayed as shown in Figure 4 10 3 Port Triggering You can configure the CPE device for Port Triggering functionality In other words depending on the requested service TCP UDP port numbers the CPE device redirects the external service request to the appro
66. e Relay Agent Quick Setup Ethernet PHY Port Status Home PORT 1 Link Down Logout PORT 2 Link Down PORT 3 Link Up 100Mbfs Full Duplex PORT 4 Link Down Radio 1 Down Radio 2 Down Figure 4 1 1 Home Information The screen contains the following details Fields in Home page Field Description Version Information 26 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel xDSL Information Connected Standard The DSL Standard which is being used currently between DSL CPE and DSLAM Default WAN Connection Current WAN mode being used in CPE IP Address Shows the IP address of default WAN connection DNS Server Shows the primary and secondary DNS servers configured in default WAN connection LAN information IP Address Shows the IP address of LAN interface of CPE This IP address to be used for accessing the CPE device from LAN side e g Web UI TELNET or UPnP sessions Ethernet PHY Port Status WLAN Information Shows the status of WLAN Radio 1 4 1 2 Quick Setup The Quick Setup is located on the left side of the screen Quick Setup provides a simple and easy step for applying minimal configuration to CPE device for making it ready to use The CPE Quick Setup window is displayed as shown in Figure 4 1 2 21 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Click on Quick Setup to view and configure the
67. eactivate and activate once the settings have been changed 230 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel SS ii When the application is used within the LAN the switch bridged mode is not necessary to set up a 3 gateway However if the application crosses various network segments LAN to WAN or WAN to LAN you must set up a gateway to connect a different network segment Regarding on how to configure a default gateway at switch bridged mode for crossing various network segments please refer to the section 4 8 1 for your reference Answer Example for configuring the gateway from static routing Destination LAN IP 0 0 0 0 Subnet Mask 0 0 0 0 Gateway 255 255 255 0 Note Static Routing functionality is used to define the connected Gateway between the LAN and lf you forgot your password you must reset your router This process will change all your settings back to the factory default To reset the router locate the reset button on the rear panel of the unit Answer With the router powered on use a paperclip to hold the button down for over 5 seconds Release the 3 button and the router will go through its reboot process The default IP is 192 168 1 1 When logging in the default username and password are both admin 231 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel System Diagnostics P
68. econds Avg Resp Time millisecs Displays the average response time in milliseconds 100 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 7 Select LAN For setting the IP address connect the wireless router to a new control PC and access the web user interface click on LAN settings You can view LAN in the left navigation bar for LAN related settings Select the LAN The menu below includes the sub menus of FA IE E55 MANGO Ud ASAS ANS Siri od dl Ei and PAN ASEO A screen is displayed as shown in Figure 4 7 LAN ARP List LAN Settings UPnP Devices LAN Switch Port Setting LAN Port Status Figure 4 7 LAN options 101 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 7 1 LAN ARP List For viewing the ARP entry list that is currently present in CPE click the LAN ARP List link LAN gt LAN ARP List on the left navigation bar A screen is displayed as shown in Figure 4 7 1 ARP List The ARP list allows you to see which clients are connected to the CPE device via IP address and MAC address MAC Address IP Address HW Type re 192 168 16 9 Oxi bciae c5 56 13 1e 192 168 16 16 Ox Figure 4 7 1 ARP List The screen contains the following details Fields in LAN ARP List Field Description MAC Address MAC Address of next hop node from ARP entry Hardware Type for ARP entry 0x1 corresponds to IEEE 80
69. entilation Place the router away from direct sunlight heat sources or areas with a high amount of electromagnetic interference Check if the network cables and connectors needed for installation are available Do not install phone lines strapped together with AC power lines or telephone office line with voice signal Avoid installing this device with radio amplifying stations nearby or transformer stations nearby Please note that the voice spectrum allowed by the wireless router internal splitter is O KHz 120 KHz VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 2 3 General Rules Before making any connections to the router please note the following rules e Ethernet Port RJ 45 All network connections to the router Ethernet ports must be made using Category 5 UTP or above for 100 Mbps Category 3 4 UTP for 10Mbps No more than 100 meters of cabling may be used between the MUX or HUB and an end node e VDSL2 Port RJ 11 All network connections to the RJ 11port must use 24 26 gauge with twisted pair phone wiring We do not recommend the use of the telephone line 28 gauge or above The RJ 11 connectors have six positions two of which are wired The router uses the center two pins The pin out assignment for these connectors is presented below Please note that the line port is no polarity therefore user can reverse the two wires of the phone cable when installed RJ 11 Pin out Assignments Pi
70. ents pertaining to the priority equal or higher to the selected level will be logged Default level logs all events For viewing system log the events corresponding to the priority level equal to or higher than the selected level will be displayed here 48 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in System Log Field Description Select the mode of log The possible options are 9 EZECH The log text is displayed in web browser itself aulachi ke H Specify the IP address and UDP port number for log transfer using syslog 9 EIEE AER This supports both options mentioned above The user can apply one of the following filters to record logging above the specified level Click on lt SAVE CHANGES gt button for applying the log level selection DSENA The default pre selected levels of logs are recorded TT Debug and above levels of logs are recorded Ines Informative and above level of logs are recorded fejite Notice type and above level of logs are recorded ll E Warning type and above levels of logs are recorded ice Error type and above levels of logs are recorded eli i 18 Critical type and above levels of logs are recorded NG Alert type and above level of logs are recorded 11H Emergency type of log information is recorded e user can apply one of the following filters to view specific logs of certain level DSENA The default
71. enus of MEUM ERSE UCU Channel ConfigVLAN Channel Config WAN Setting WAN StatusIDNSMDDNSI and 1 9 jente A screen is displayed as shown in Figure 4 6 Wh Mode Selection Auto Detect Conti g WAN Channel Config VLAN Channel Config WAM Setting Mah Status DNS DENS OAM Configuration Figure 4 6 WAN options 61 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 1 WAN Mode Selection For configuring the WAN Mode Setting click the WAN Mode Selection WAN gt WAN Mode Selection on the left navigation bar A screen is displayed as shown in Figure 4 6 1 WAN Mode Selection This page allows to select the physical WAN mode in CPE device This has to be first configured before any WAN configuration is done Physical WAN Selection Physical WAN Type Auto xDSL e Figure 4 6 1 WAN Mode Setting Selected Auto Physical WAN Selection Physical WAN Type DSL v TC Type Auto xTM ha Negotiated WAN Mode WAN Type VDSL2 TC Type PIM IC Figure 4 6 1 1 WAN Mode Setting Selected ADSL2 VDSL2 62 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in WAN Mode Setting Field Description Failover Support select this checkbox to enable Dual WAN support Choose the WAN type from the drop down list For multi WAN mode supported CPE Physical WAN Type
72. er mit Switch und Access Point Telekom VDSL2 kompatibel Fields in PPPoA WAN Configuration Description This option allows to select following modes of IPv6 configuration Configuration Modes Stateful DHCPv6 IA_NA and IA_PD SLAAC Address Configuration with DHCPv6 IA_PD This option allows to configure different DUID DHCP Unique Identifier types DUID Type Type 1 LLT Link ag Time Type 2 EN Enterprise Number Type 3 LL Link Layer IANA option represents IPv6 address and parameters related to the same being accepted by IANA ID DHCPVv6 clients IANA is the Identity Association for Non Temporary Addresses option This Identifier has to be configured when Stateful DHCPv6 configuration mode is selected IAPD options represent one or more IPv6 prefix and parameters related to it IAPD is the IAPD ID Identity Association for Prefix Delegation This identifier to be configured in both Stateful CS DHCPv6 or SLAAC DHCPv6 configuration modes This parameter is called Site Level Aggregation Identifier This identifier is used to configure the subnet for DHCPve6 client configuration Commit Handshaking will happen with two DHCPv6 messages This option allows configuring default route for relevant WAN mode of this WAN connection Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes VC 400RTW VDSL2 Slave Modem Router mi
73. ery time the user presses the WPS button there will be two minutes of time to detect the available equipment RJ 11 Terminal Block WPS Button 2l VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Before installing power and device please read and follow these essentials Use separate paths to route wiring for power and devices If power and device wiring paths must cross make sure the wires are perpendicular at the intersection point Note Do not run signal or communications wiring and power wiring through the same wire conduit To avoid interference wires with different signal characteristics should be routed separately 990 9 You can use the type of signal transmitted through a wire to determine which wires should be kept separate The rule of thumb is that wiring sharing similar electrical characteristics can be bundled together You should separate input wiring from output wiring We recommend that you mark all equipment in the wiring system The maximum wireless data transfer rate is derived from IEEE Standard 802 11 specifications Actual data transfer rate will vary from network environment including distance network traffic building site materials construction interference from other wireless devices and other adverse conditions 22 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Chapter 4 Configuring the wireless
74. for speed and convenience Since your Service Provider may connect to the Internet with dynamic IP WAN settings it is likely that the DNS server IP addresses are also provided dynamically However if there is a DNS server that you would rather WAN Mode Selection use you need to specify the IP address below Auto Detect Config WAN Channel Config Domain Name Server DNS Address VLAN Channel Config WAN Setting WAN Status Secondary DNS Address optional E E Fs DNS DDNS OAM Configuration Configure example WAN DNS Items Setting argument Action DNS Address DNS IP 168 95 1 1 Example Note When configuration is completed with the above arguments please reboot the wireless router 150 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel PC Nic card setting Configure example Items Setting argument Action IP Address PC LAN IP 192 168 1 30 Example Gateway 192 168 1 204 Example 151 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 3 Packet Filtering configuration wireless router Packet Filtering System gt www Modify packet filtering rule xDSL gt i Filtering Internet access for LAN clients can be controlled from here based on IP address WAN gt LAN gt Route gt Firewall Setting IPv6 Firewall Setting Packet Filtering Protocol TCP Source IP Type ALL v Source I
75. functionality is enabled through Quick Setup gt IPv6 then the Routing Table List web page also lists all IPv6 routes in system under IPv6 tab as shown in Figure 4 8 3 1 Routing Table The Routing table displays configured routes and interfaces on CPE device A E FcO0 64 256 bro feB0 64 y 256 ord fe80 64 256 eth o2 1 128 ff02 1 O bro OO 48 E 256 bro fF00 8 256 etho 00 8 y 256 ptm FFOO 8 Mi 256 ptmO 201 IPv 6 functionalities are not supported in this software version Figure 4 8 3 1 Routing List IPv6 Tab 124 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 9 Select Wireless This section describes Wireless LAN configuration options in CPE web page This section applies only to those CPE systems which support Wireless LAN functionality You can view the Wireless link on the left navigation bar of the wireless router CPE homepage The menu below includes the sub menus of REIES ME EE E WMM Settings and WPS Settings Following are the options available under Firewall as shown in Figure 4 9 Wireless gt Radio Settings security Settings WMM Settings WPS Settings 125 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 9 1 Radio Settings For viewing the radio settings click Radio Settings link Wireless gt Radio Settings on the left navigation bar A screen is displayed as s
76. g are the options available under Route menu as shown in Figure 4 8 Static Routing RIP Support Routing Table List o Figure 4 8 Route Options on the Left Navigator Bar 116 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 8 1 Static Routing The static routing function determines the path that data follows over your network before and after it passes through your router You can use static routing to allow different IP domain users to access the Internet through this VDSL2 Router device For setting up Static Routing click the Static Routing link Route gt Static Routing on the left navigation bar A screen is displayed as shown in Figure 4 8 1 Static Routing The static routing function determines the path that data follows over your network before and after t passes through your router You can use static routing to allow different IP domain users to access the Internet through this device The default route cannot be added from this web page The default route is added in system automaticaly based upon the Gateway selection in WAN Settings page MEA E Eee lil ILL LIT ne rif ID DD E eo Figure 4 8 1 Static Routing Configuration 117 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Static Routing Field Description eke
77. guration to save the information that you have entered Click Cancel to exit from this page without saving the changes When you have chosen IPv4 tab and click Add button in the Packet Filtering page a screen is displayed as shown in Figure 4 10 3 1 If you choose IPv6 tab and click on Add button a screen is displayed as shown in Figure 4 10 3 2 142 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Add a packet filtering rule Allows to ceate a packet filtering rule thereby conforming traffic is denied access Protocol ALL w Source IP Type SUBNET Source IP Address II Source Netmask Source Fort e Destination IP Type SUBNET v Destination IP Address J Destination Netmask Destination Port Ingress Interface Egress Interface Source MAC Address Mi Enable Figure 4 10 3 1 Add a Packet Filtering Rule for Firewall IPv4 143 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Add a Packet Filtering Rule page Field Description To select the protocol The options available are ALL TCP UDP ICMP AH and ESP IP Address To specify the source IP address To specify the range of the source port Valid for protocols TCP or UDP only IP Address To specify the destination IP address Destination Port To specify the range of the destination port Valid for pr
78. h und Access Point Telekom VDSL2 kompatibel 188 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 11 3 Class Configuration For classifying the upstream traffic click the Class Config link QoS gt Class Config on the left navigation bar A screen is displayed as shown in Figure 4 11 3 WAN Egress Classifier Configuration Configures classification entries in CPE device to be used in conjunction with other QoS entities Sica 17 1 DOWNS Classifier Classifier Queue Outgoing Action Help n Figure 4 11 3 Class Configuration 189 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Class Configuration Field Description Upstream Downstream Selection tab for upstream downstream Classifier configuration Order This shows the order of the classification entry Classifier Interface This is a Packet Input Source for classified flow Outgoing DSCP This is the DSCP mark for next hop Selection option for deleting or modifying action on chosen classifier Delete button for deleting selected queue 190 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel When you click Add or Modify in the Classifier Configuration page a screen is displayed as shown in Figure 4 11 3 1 Add Modify a WAN Egress Classifier Rule Classifier Name Enabl
79. he global Internet Administrator Settings Web Settings Software Firmware Upgrade Current System Time 1 3 Configuration Settings Set Time Zone GMT 05 30 Calcutta Chennai Mumbai New Delhi Sri Jayawardenepura System Log e e a Tom am mm Tamm a mean SSL Certificate SNTP Client Reset a Primary SNTP Server 0 asta poolntp ora v Statistics P i Secondary SNTP Server 1 asia pool ntp org v Optional a a O Figure 4 3 2 System Time Configuration 39 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Fields in System Time Field Description Current System Time Current Time in System shown in Day Date and Time of day SNTP Client Tick on Check box if SNTP client has to be enabled Fields in System Time Cont d Field Description Secondary SNTP Server Backup NTP Server optional Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes Note Static Routing functionality is used to define the connected Gateway between the LAN and WAN For example if we want to activate the Network Time Protocol NTP service we have to define the Gateway connected to NTP server in the WAN Please refer to static routing for your reference 40 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 3 3 Administrator
80. he path and name of the image file to be upgraded and click the APPLY button below You wil be prompted to confirm the upgrade After the upgrade process it will boot the system Help Figure 4 3 5 Software Firmware Upgrade Click Browse to specify the software image file from host to be upgraded in system Click Apply to start the software upgrade process Note You can click Home on the left navigation bar to view the current software version 44 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 3 6 Configuration Settings For managing the configuration of the system click the Configuration Settings link System gt Configuration Settings on the left navigation bar This page allows users to backup the current configuration of CPE to host PC or restore the previously backed up configuration in host PC to CPE as displayed in Figure 4 3 6 A IST Configuration Settings Host Name Config i You can manage the CPE device configuration settings The current configuration of CPE device can be downloaded to PC using BACKUP button and can be uploaded back using RESTORE button System Time Administrator Settings Backup Web Settings i Backup to local host Software Firmware Upgrade Configuration Settings System Log Restore SSL Came O Restore from local host Reset statistics THE EXA Figure 4 3 6 Configuration Settings Fields in Configuration Settings Description
81. hown in Figure 4 9 1 this screen will show two tabs Radio 1 and Radio 2 for Concurrent Dual Band WLAN platforms WLAN Radio Settings Configure common WLAN parameters applicable to all active AP VAP in the system Name Settings SSID vdsl2_wifl Wireless Lan Enable Frequency Band 2 4GHZ w Country UNITED STATES v Auto Channel Select Enable Channel No Operational Mode 302 1186N v Channel Bandwidth 20 40MHz Auto w Extension Channel ani Guard Interval Short 400ns w MCS Auto el Figure 4 9 1 Radio Settings 126 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Radio Setting Field Description Service Set Identifier public name of WLAN Network Country where WLAN CPE is operating Care Channel No to be used in WLAN AP When Auto Channel Select is enabled this option cannot be used 802 11n Settings Channel Bandwidth Channel Bandwidth 20 or 20 40 MHz Extension Channel Extension channel position Above Control Channel or Below Control Channel Guard Interval Guard interval between channels MCS Modulation and Coding Scheme Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 127 VC 400RTW VDSL2 Slave Modem Router mi
82. ibel 4 6 5 4 PPPoA The PPP over ATM PPPoA mode is valid only for ATM based WAN To configure the WAN interface to use PPPOA select the option PPPoA option A screen is displayed as shown in Figure 4 6 5 6 WAN The CPE device can be connected to your service provider in any of the following Ways Attached Channel 5 VCC pppoatm 1 al WAN TYPE PPPoA User Name Password Please retype your password MTU pppoa 1400 1492 pppo0e 1400 1500 1492 PPP Option Auto Connect Address Version IPy4 4 IP WAN IPv Configuration Configuration Modes Stateful DHCPw6 4_ MA andlA_FO DUID Type Type 1 LLT Link Layer Time IANA ID D IAFD ID O SLA TD o Rapid Commit Fl Default WAN El Figure 4 6 5 6 WAN PPPOA creation 83 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in PPPoA WAN Field Description User Name To enter the username to be used in the PPPoA session Please retype your password To enter the password again to reconfirm This feature allows the device to automatically re connect to the service provider if the connection is lost The checkbox can be enabled or disabled for this feature l For PPPOA the only supported IP addressing is IPv4 currently The IPv6 for PPPoA Address Version l l l i l is not available in this version of wireless router Dial on Demand 84 VC 400RTW VDSL2 Slave Modem Rout
83. ick the WAN Setting link WAN Setting gt WAN on the left navigation bar to specify the WAN settings Please uncheck the Auto Detect Enable option and click Add to configure the WAN type 222 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel WAN Setting Auto Detect Enable ial 1 WAN Channel WANIPO PTM VLAN 201 Bridge WANPPP1 PTM VLAN 201 PPPoE O EE i Figure C 2 WAN Setting 3 Please refer to the section 4 5 6 for configuring the WAN type the user can configure the Dynamic IP Address Static IP Address PPPoE mode 223 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel WAN The CPE device can be connected to your service provider in any of the folowing ways Attached Channel E pim 201 v WAN TYPE Address Version IPv IP address assigned by your ISF i Subnet Mask ISP Gateway Address J Figure C 3 Configuring WAN Type Click Apply for applying the changes Click Cancel to exit from this page without saving the changes 224 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel oo ADH VDSL2 CO Router wireless router Compatibility Table The following shows the band profile and band plan compatibility table Band Profile List Band Plan List 0 VDSL2 Profilesa 0 Annex AM1_EU32 1 VDSL2 Profile8b 1
84. igure 4 6 4 2 VLAN Channel Configuration Add The screen contains the following details Fields in VLAN Creation Field Description VLAN Channel Name User specified VLAN Channel name VLAN Id VLAN identifier in range of 7 4095 VLAN Identifiers 1 6 are internally used in system for special purpose and are not available to user for configuration Click Add to save the information that you have entered Click Cancel to exit from this page without saving the changes 73 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 5 WAN Setting For configuring the WAN interface click the WAN Setting link WAN gt WAN Setting on the left navigation bar and a screen is displayed as shown in Figure 4 6 5 WAN Setting Auto Detect Enable Figure 4 6 5 WAN Setting Auto Detect Enable WAN Setting Auto Detect Enable Default WANIPO PTM VLAN None Bridge Figure 4 6 5 1 WAN Setting The wireless router can support up to a maximum of 16 WAN connections in system When hardware based QoS is enabled in 74 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel system it limits the number of VCCs to 8 only for ATM based WAN For creating a new WAN connection click Add in the WAN setting page Please follow the rest of the steps for creating the WAN connection The last column named DEFAULT GATEWAY allows selecting the WAN f
85. ilable options are Off CPE policy High and Low Please note that the user must enable IPv6 settings before configuring the IPv6 firewall Click Apply for committing the desired action Click Cancel to exit from this page without saving the changes 140 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 10 3 Packet Filtering For enabling Packet Filtering click the Packet Filtering link Firewall gt Packet Filtering on the left navigation bar A screen is displayed as shown in Figure 4 10 3 Packet Filtering Configure packet filter rule for denying the packets conforming to it ve Enable Packet Filter Source ad rce Destination en runde Ingress Foress source MAC Enable IP IP Interface Interface Address Figure 4 10 3 Packet Filtering Delete Al 141 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Packet Filtering Field Description IPV4 IPv6 Choose the appropriate tab to configure Filter IP Address range of the local machine under wireless router CPE Destination IP IP address of the destination Filter protocol TCP or UDP Egress Interface Output interface of the packet To provide more IP Addresses of the WAN interface Delete All To delete all the packet filtering rules configured in system Click Apply at any time during confi
86. image the dropdown will present following options ADSL2 VDSL2 xDSL Auto WAN Ethernet over MII O WAN Ethernet over MII 1 3G WAN and LTE WAN Choose the Transmission Convergence from the drop down list 1 ATM TC or 2 PTM TC or 3 Auto This field is displayed only if ADSL2 or xDSL is chosen as the WAN type WAN Type show WAN type status TC Type Show TC type status Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 63 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 2 Auto Detect Setting Auto detect feature Is a fully automatic way to find and configure the VC channel or VLAN channel for active WAN PHY of the device and WAN protocol for the same either PPPoE DHCP User has to provide pool of VC channels or VLAN channels which will be probed one by one sequentially and upon successful detection of a channel WAN protocol probing will be done and configured in the device For configuring the Auto Detect Config click Auto Detect Config WAN gt Auto Detect Config on the left navigation bar A screen is displayed as shown in Figure 4 6 2 Auto Detect Setting Auto Detect Pool Config ADSL PTM VLAN Pool 101 0 N Add Delete ADSL PTM VLAN to Pool pe VDSL PTM VLAN Pool 201 0 Add Delete VDSL PTM VLAN to Pool A AA Delete MII 1 VLAN P
87. ing Supports ATM Total Upstream Priority Queues Supports uPnP PPPoE PPPoATM IPv4 IPv6 NAT NAPT Supports static routing for IPv4 and IPv6 forwarding Supports Firewall functions contains Packet filtering DMZ Mac Address based filtering Parental Control Application based filtering Supports DHCP Server DHCP Relay DHCP Client DHCPv6 Client DHCPv6 Server DNS DNS Proxy or Relay DNSv6 Proxy or Relay NTP Client HTTP1 1 server Supports Multicast IP table IGMP v3 Proxy and Snooping Supports IEEE 802 1p VLAN Priority and mapping to DSCP Supports HT TP HTTPS SSL web management 9 999999 9 os 219 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Supports remote management and monitor Supports configuration backup and restore Provides surge protection for Line port Supports Router amp Switch Bridged mode selection Supports 8 queue MFC DSCP both type QoS Note 1 Features and specifications in this manual are subject to change without prior notice 2 Firmware upgradeable for future enhancement Product Specification Wireless Frequency Ranger ee Full duplex IEEE 802 3x Flow control Half duplex Back pressure 220 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel LED Indicators Switch method Typical Power Consumption Power Input EMC Storage Temperature Humidity
88. ion 240 255 Forward Error Correction Sz GG ywpe Seeends FECS L O a Downstream Errored Second ES L 0 1672 Data Rate 100012 kbps 60016 Soe Serverely Errored Seconds SES L 0 116 oy mel Data 140868 kbps 62576 kbps Lose of Signal Seconde LOSS L O 108 e Unavailable Seconds UAS L 82 82 rap Interieaver Depth 1 ina Line Attenuation LATN 0 1 dB 0 0 dB Signal Attenuation SATN 0 1 dB 0 0 dB Signal to Noise Ratio Margin SNRM 16 9 dB 8 6 dB Actual Aggregate Transmit Power ACATP 13 1 dB 11 9 dB me mm mm we ww www we ww we wwe wwe we we Pm PP we we we we ww Pm PP PP PP PP ww PP PP wwe wwe ww we we ws we ww we ow we we we ow we ww we ww ow we ow we nw zo ew eS l X X X Figure 4 5 1 xDSL Status 59 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in xDSL Status Field Description Displays the Vendor ID Version Number and the Serial Number of the ATU C System Vendor Information ATU C DSLAM Displays the data rate and the maximum attainable data rate Displays the performance figures of the physical xDSL line 60 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 Select WAN You can view WAN link on the left navigation bar for WAN related settings Select the NAT The menu below includes the sub m
89. isplayed as shown in Figure 4 10 6 Application Server Settings Application laver protocol services like Web server Telnet server TFTP server FTP Server and SNMP can be enabled disabled from this page Https Web Server Accept from WAN Port 1443 Http Web Server Accept from WAN Port ET Accept from LAN Telnet Server Accept from WAN Port 23 Accept from LAN TFTF Server Accept from WAN Port 53 Accept from LAN FTF Server Accept from WAN Port 21 Accept from LAN SNMP Accept from WAN L Help T Cancel Figure 4 10 6 Application Server Settings 159 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Application Servers Settings Field Description Web Server settings The acceptance from WAN The Port Number The acceptance from LAN Web Server TFTP Server Settings The acceptance from WAN The Port number The acceptance from LAN TFTP Server FTP Server Settings The acceptance from WAN The Port number The acceptance from LAN FTP Server Click Apply for committing the App Server settings Click Cancel to exit from this page without saving the changes 160 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 10 7 Access Control List ACL For configuring the access control list click the ACL link Firewall gt ACL
90. m Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 5 Select xDSL You can view the xDSL link on the left navigation bar of the CPE Home page This web page is available only on DSL platforms Select the xDSL The menu below includes the sub menus of 48j B cits A screen is displayed as shown in Figure 4 5 xDSL Status Figure 4 5 Select xDSL Note These options help to monitor and configure the DSL physical parameters in the device 58 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 5 1 xDSL Status For viewing the xDSL Status click the xDSL Status link xDSL gt xDSL Status on the left navigation bar A screen is displayed as shown in Figure 4 5 1 NE A a a ET eg ee eM en aw ge I ee ee eee es a ee eg gg ge Re ee se ee a I ee ee 1 xDSL Line Status Provides detailed information about xDSL line s current attributes ATU C System Vendor Information l Vendor ID B5 00 42 44 43 4D 00 00 Vendor Version Number 76 30 39 2E 30 37 2E 31 35 20 20 20 20 20 20 00 Near End Far End Vendor Serial Number 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Superframe Not avallable LOS Failure 0 0 Modem Status SHOWTIME SYNC LPR Failure 0 0 Mode Selected VDSL 17A 3 NCD Failure 0 o Power Management Mode DSL_G997 PMS LO LCD Failure 0 0 Trellis Coded Modulation Enable CRC 0 1793 Latency Type Fast l RS Correct
91. mation message is displayed as shown in Figure 4 3 9 1 j Do you really want to perform this operation on CPE Y Figure 4 3 9 1 Reset Confirmation Message Click Ok to perform the operation on CPE Click Cancel to exit from this page 52 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 4 Select Statistics Select the Statistics link on left navigation menu The menu below includes the sub menus of and WAN A screen is displayed as shown in Figure 4 4 Statistics Figure 4 4 Statistics in the left navigator bar 53 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 4 1 LAN For viewing the LAN Statistics click the LAN link Statistics gt LAN on the left navigation bar A screen is displayed as shown in Figure 4 4 1 System gt LAN Statistics Statistics The LAN Statistics gives the per interface statistics on the LAN side LAN WAN Interface ES BR xDSL gt Dropped Dropped WAN gt atho 477 239420 0 0 515 58102 0 0 LAN Route gt Firewall gt Ethernet Ports Statistics NAT I y 005 Port Multicast IPsec 1 0 0 0 0 IPv6 gt Diagnostics gt l 2 0 0 0 0 Quick Setup E 2088 604587 515 67372 E 4 0 0 0 a Logout Figure 4 4 1 LAN Statistics 54 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details
92. mum of 250 Mbit s at source to 100 Mbit s at 0 5 3 3 km 1 600 ft and 50 Mbit s at 1 km 3 300 ft but degrades at a much slower rate from there and 3 still outperforms VDSL Starting from 1 6 km 1 mi its performance is equal to ADSL2 3 ADSL like long reach performance is one of the key advantages of VDSL2 LR VDSL2 enabled 3 systems are capable of supporting speeds of around 1 4 Mbit s downstream over distances of 4 5 3 km 2 5 3 miles gradually increasing the bit rate up to symmetric 100 Mbit s as loop length shortens This means that VDSL2 based systems unlike VDSL1 systems are not limited to short 3 local loops or MTU MDUs only but can also be used for medium range applications 3 Signal to noise ratio often abbreviated SNR or S N is a measure used in science and engineering 3 3 that compares the level of a desired signal to the level of background noise It is defined as the ratio 3 of signal power to the noise power A ratio higher than 1 1 indicates more signal than noise While Answer SNR is commonly quoted for electrical signals it can be applied to any form of signal such as isotope levels in an ice core or biochemical signaling between cells The ratio is usually measured 3 in decibels dB The signal to noise ratio the bandwidth and the channel capacity of a communication channel are VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel r _ A _ _
93. n MNEMONIC FUNCTION 1 NC Unused fe e Used 10 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 2 4 Connecting the Router The router has four Ethernet ports which support connection to Ethernet operation The devices attached to these ports must support auto negotiation 10Base T 100Base TX 1000Base TX unless they will always operate at half duplex Use any of the Ethernet ports to connect devices such as Monitor systems Servers Switches bridges or routers Notes 1 The RJ11 Terminal Block Line port is used to connect the telephone that is connected to VDSL2 VC 400LT and VC 400RTW Router Point to point solution 2 The Slave device CPE must be connected to the Master device CO through the telephone wire The Slave cannot be connected to another Slave and the Master cannot be connected to another Master 2 5 Connecting the RJ 11 RJ 45 Ports The line port has 2 connectors RJ 11 and terminal block It is used to connect with VDSL2 CO Router CO using a single pair phone cable to wireless router CPE bridge side point to point solution Take note that wireless router line port RJ 11 and terminal block cannot be used at the same time either RJ 11 port or terminal block is connected using a straight connection Figure 2 1 11 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel RJ 11 When inserting a RJ 11 plug make
94. n IPv4 IPWa IP address assigned by your ISP f i Subnet Mask j l l ISP Gateway Address i IPv6 address assigned by your ISP Prefix Length IPv6 Gateway Address Lan Prefix IPv6 DNS Servers IPv Primary DNS Server address IPv6 Secondary DNS Server address Default WAN u Figure 4 6 5 4 WAN Static IP 78 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Static IP Field Description Address Version IP address assigned by your ISP To specify the IP Address of wireless router CPE s WAN link ISP Gateway Address IPv6 To specify the Gateway address of the wireless router CPE s WAN IPv6 address assigned by your ISP This is the static IP address for the WAN interface IPv6 Gateway Address This is the default gateway IPv6 DNS Servers IPv6 Primary DNS Server Address This is the primary DNS server This option allows configuring default route for relevant WAN mode of this WAN Default WAN l connection Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 79 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 5 3 PPPoE To configure the WAN interface to use PPPoE ch
95. nector and it consists of six pins POTS plain old telephone services use pins 3 and 4 for voice transmission A telephone cable is shown below Figure A 6 A B f poe f r 2 aN _ x S y a J J Figure A 4 Telephone cable The A and B connectors on the rear of the Modem are RJ 11 connectors These connectors are wired identically The RJ 11 connectors have six positions two of which are wired The Modem uses the center two pins The pin out assignment for these connectors is presented below Table A 3 Table A 3 RJ 11 Pin out Assignments Pin MNEMONIC FUNCTION Unused 2 NC so m ao pe e m 218 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Ve el ale1 m Product Specification Key Features amp Benefits Compliant with IEEE 802 11b g n wireless standard with 2T2R Up to 300 Mbps Supports WPS PIN PBC Supports WEP WPA WPA2 TKIP AES Supports QoS WMM WMM PS Low power with Advanced Power Management Supports ATM and PTM transmission mode auto detection ADSL backward compatible Supports high bandwidth up to 100Mbps symmetric over line ports Supports 8a 8b 8c 8d 12a 12b 17a 17b and 30a band profile Supports 997 998 band plan Supports ATM TC ATM and AAL5 ATM Flow Throughput OAM Cell Filter and Forwarding AAL5 SAR PVC ATM Traffic Class ATM PVC Shaping ATM PVC Schedul
96. ng wireless router first when powered on 2 7 Replace the defective router or cable if necessary 22 Cause BH _ __________ 0 Solution VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel VDSL setting failure or phone cable length is over the specification limit eae ei sss sss 3 1 Please make sure that the phone wire must be connected between VDSL2 CO Router CO and wireless router CPE when both are power on VDSL2 CO Router CO will do link speed function depending on phone wire length therefore if VDSL2 CO Router CO can t detect wireless router CPE over phone wire while both power on this will cause the link to fail 3 3 2 Please check the phone wire we recommend using 24 26 gauge twisted pair cables without rust 3 3 Please reinsert power when changing the cable length or link time over 3 minutes wegen ne en nn n nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn nn a 3 The phone wire must meet CAT 3 standard or above and without clustering otherwise it will cause more cross talk reducing the DSL power driver 3 Answer 3 Very high speed digital subscriber line 2 VDSL2 is an access technology that exploits the existing 3 3 infrastructure of copper wires that were originally deployed for traditional telephone service It can be deployed from central offices from fiber optic connected cabinets located near the customer
97. nt Telekom VDSL2 kompatibel 4 6 4 VLAN Channel Configuration For configuring the VLAN Channel Configuration click the VLAN Channel Config WAN gt VLAN Channel Config on the left navigation bar A screen is displayed as shown in Figure 4 6 4 VLAN DISPLAY This page allows management of wlan channels Auto Detect Enable Figure 4 6 4 VLAN DISPLAY This page allows management of vlan channels Auto Detect Enable ptm 20i ptm 201 MITT CH_1 eth Fi eth1 7 LJ Figure 4 6 4 1 VLAN Channel Configuration Display Auto Detecting does not check the checkbox 71 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in VLAN Display Field Description Auto Detect Enable To enable Auto Detect Base WAN Name Displays the L2 interface names over which VLAN Channel has been configured Select Select this option to delete a specific VLAN channel VLAN interface name Click Add to save the information that you have entered Click Cancel to exit from this page without saving the changes 72 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel When you click Add button inside the VLAN Channel Configuration page a screen is displayed as shown in Figure 4 6 4 2 Vlan Creation Vian Channel Name Mode Name 4 PTM 0 v VLAN Id I 0 4095 Override MAC Address Help F
98. o party lines is subject to state tariffs FCC Warning This equipment has been tested pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment can generate use and radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at owner s expense CE Mark Warning In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures 234 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately PF Warranty The original product that the owner delivered in this package will be free from defects in material and workmanship for one year parts after purchase There
99. ode Auto Force 10Mb Half Force 10Mb Full Force 100Mb Half Force 100Mb Full Figure 4 7 4 All LAN Port Setting Default value is Auto 10 100 Full Half Click Apply to save the information that has been entered Click Cancel to exit from this page without saving the changes 114 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 7 5 LAN Port Status For viewing the LAN Port Status in LAN network click the LAN Port Status link LAN gt LAN Port Status on the left navigation bar A screen is displayed as shown in Figure 4 7 5 Lan Status The following information provides a view of the current Ethernet ports status of the unt Ethernet PHY Port Status POR T 1 Link Down PORT 2 Link Down POR T 3 Link Down PORTA Link Up 100Mb s Full Duplex Figure 4 7 4 LAN Port Status Example Table Output 1 Output 2 Output 3 Output 4 10M Full Force 10M Full 10M Half None Link Down NWAY 10M Half 10M Half Output 5 Output 6 Output 8 100M Half Force 100M Full 1 Half 100M Full 100M Auto 100M FULL l a El 115 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 8 Select Route lf there are multiple routers installed on your network it is necessary to configure the VDSL2 router unit s routing functions Select the Route The menu below includes the sub menus of Sicilia RAINT L and AE Followin
100. omise of VDSL2 max 100Mbps Symmetric technology Switch Managed VDSL2 IP DSLAM ss 5 lt r a e Bees ses eee mo LL 100Mbps Syiinatic 100Mbps Symmetric J ES a a A m ae 16 vun oad m CPER r Cafe Shop Wireless Router ees Router Smart phone Tablet Smart phone Tablet Figure 2 2 wireless router applications 13 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel VDSL2 Point to Point VDSL2 CO Router N VDSL2 CPE Router s Ethernet Line Phone Line VDSL2 Point to Multipoint gt VDSL2 Bridge ETE 2 VDSL2 Bridge with PoE VDSL2 IP DSLAM Ss u vo J Managed VDSL2 Router 62 ee os o PBX Managed VDSL2 Router with Wireless Figure 2 2 1 VDSL2 applications 14 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 9 2 6 1 Connect the VDSL2 CO Router and the wireless router to the Line The objective for VDSL2 is to pass high speed data over a twisted pair cable In the setup connect VDSL2 CO Router to wireless router through phone wire 24 26 AWG or line simulator or any other hardware representation of a cable network with or without noise injection and crosstalk simulations 2 6 2 Connect the VDSL2 CO Router and the wireless router to LAN Devices In the setup usually an Ethernet tester serves as a representation of the LAN side
101. on bar A screen id displayed as shown in Figure 4 6 6 WAN Status PTM VLAN 201 Gateway Information DNS Information Primary Secondary PPPoE UNCONFIGURED Unconfigured Unconfigured WIANPPP1 Figure 4 6 6 WAN Status 89 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in WAN Status Field Description IPv4 IPv6 Choose the appropriate tab to view the status Connection Type The type of the connection mode in which wireless router is configured Displays the IP address in use Configured Connection Name Displays the configured connection name DNS Information Provides information about the primary and secondary DNS 90 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The control buttons shown against few WAN are explained below Fields in Control Fields displayed in WAN Status Screen Field Description This button appears only for PPPoA and PPPoE type of WAN links On clicking this button it tries Connect to establish PPP link Er This button appears only for DHCP type of WAN links On clicking this button it tries to establish renew the current lease 91 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel When you click on the IPv6 tab in the WAN Status page a screen is displayed as shown in Figure 4 6 6 1
102. onfiguration mode The Local Host Configuration restore is shown in Figure 4 3 6 2 The system will reboot after the configuration is restored When the CPE boots up it will be running with the newly applied configuration Configuration Restore The CPE device configuration file backed up earlier can be loaded back on CPE device Enter the path and name of the Configuration file and then click the APPLY button below You will be prompted to confirm the restore process NOTE The Configuration file should be in gzipped i e with suffix gz Figure 4 3 6 2 Configuration Restore Click Apply button to restore the configuration settings 47 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 3 7 System Log For viewing the logs produced in the system click the System Log link System gt System Log on the left navigation bar A screen is displayed as shown in Figure 4 3 7 System Log Configure System Log Local Remote O Local and Remote Filter Level Default v View System Log Filter Level Default v 1 Figure 4 3 7 System Log This page allows managing logging options in CPE device If Local is selected the events are logged locally in the system 6 If Remote is selected the messages are logged to a remote server 6 If Local and Remote option is selected messages are logged locally in the system as well as to the remote server The ev
103. ool 301 0 Add Delete MII 1 VLAN to Pool a po HER MII D VLAN Pool 401 0 Add Delete MII O VLAN to Pool a I YCC Pool 0 32 8 35 0 35 Add Delete VCC to Pool l n Auto Detect Layer Specific Setting L2 VCC Auto Detect L3 vcc Auto Detect ee L3 ADSL PTM Auto Detect Detect hor Sa L3 YDSL PTM Auto Detect L2 MII 1 VLAN Auto Detect L2 MII O VLAN Auto Detect L3 MII 1 Auto Detect L3 MII O Auto Detect K K K Figure 4 6 2 Port Mapping Configuration 64 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Auto detect Config Field Description Add Delete VDSL PTM VLAN to Pool Add or delete VLAN to VDSL PTM VLAN pool MII 1 VLAN Pool This displays the current configured VLAN pool for auto detect in MII 1 WAN mode Add Delete MII O VLAN to Pool Add or delete VLAN to MII O VLAN pool L2 VCC Auto Detect Select this to enable VCC auto detection from the specified pool for ADSL ATM WAN mode L2 ADSL PTM VLAN Auto Detect Select this to enable VLAN auto detection from the specified pool for ADSL PTM WAN mode L2 VDSL PTM VLAN Auto Detect Select this to enable VLAN auto detection from the specified pool for VDSL PTM WAN mode 65 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Fields in Auto detect Config cont d Field Description L2 MII 1 VLAN
104. oose the option PPPoE A screen is displayed as shown in Figure 4 6 5 5 WAN The CPE device can be connected to your service provider in any of the following ways Attached Channel 1 ptm0 201 i WAN TYPE PPPoE i User Name Password Please retype your password Service Name i Optional Access Concentrator Name A a Optional Relay LAN site PPPoE session 0 MTU pppoa 1400 1492 pppoe 1400 1500 1492 7 PPP Option Auto Connect Address Version IPv4 IPv6 WAN IPv6 Configuration Configuration Modes Stateful DHCPv6 A 1A a nd lA_PD w DUID Type Type 1 LLT Link Layer Time Y IANA ID lo IAPD ID SLA ID o Rapid Commit O Default WAN a Help Figure 4 6 5 5 WAN PPPoE creation 80 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in PPPoE WAN Field Description User Name To enter a username for PPPoE session used for authentication in B RAS Please retype your password To enter the same password again to reconfirm Access Concentrator Name PPP Access concentrator Name optional Relay LAN site PPPoE Session This feature allows enable disable a PPPoE relay session Address Version This option allows configurability of IPv4 and or IPv6 stack on per WAN interface 81 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Fields in PPPoE
105. or relevant WAN mode setting in WAN setting web page When the user clicks any of the radio buttons he will be asked to confirm the same If the user clicks Apply the default gateway will be configured on the selected WAN connection otherwise the changes will not be applied The screen contains the following details Fields in WAN Settings Field Description Auto Detect Enable To enable Auto Detect WAN Channel Provides information of layer 2 WAN channel configured This option is present only in IAD models where VoIP is s orted This is the Default VoIP Interface pr Se y 2 ns A default interface for VolP packets When you click Add button in WAN Settings web page a screen is displayed as shown in Figure 4 6 5 2 75 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel WAN The CPE device can be connected to your service provider in any of the following ways 1 pim0 201 v Dynamic IP Address nd Dynamic IP Address Static IP Address PPFoE Attached Channel WAN TYPE Bridge Default WAN wll Heip Figure 4 6 5 2 WAN Settings Apply Step1 The screen contains the following details Fields in WAN Settings Apply Step1 Field Description Attached Channel Select the WAN Channel e g PVC from drop down being configured as WAN To enter the WAN interface IP Address of wireless router enable this field and click Static IP Address Appl
106. orted queue ES Committed or Guaranteed Shaping Rate in Kbps or Percentage Shaping Rate This provides the status of queue entry Enabled or Disabled Add This button is used to add a new queue Modify This button is used to modify the selected queue entry 185 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel When you click the Add button in the Port Triggering page a screen is displayed as shown in Figure 4 11 2 1 Add Modify a WAN Egress Queue Entry Queue Name Queue Interface WAN v Queue Precedence 1m Queue Drop Type RED RED Min Threshold fs RED Max Drop Probability i Queue Scheduler Type Strict Priority Queue Weight o Apply Shaping E Enable E Figure 4 11 2 1 Add Modify a Queue Entry 186 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Add Modify a Queue Entry Field Description Name or Identifier of Queue Queue Precedence Precedence of Queue Lower values denote higher priority RED Min Threshold RED Threshold Value applicable for RED Drop algorithm Queue Scheduler Type Queue scheduling Algorithm SP or WFQ Apply Shaping To apply shaping on queue Click Apply for applying the changes Click Cancel to exit from this page without saving the changes 187 VC 400RTW VDSL2 Slave Modem Router mit Switc
107. otocols TCP or UDP only Egress Interface To specify the output interface of the packet from dropdown options e g WANZ2 Enable To enable disable the particular packet filtering rule Click Apply at any time during configuration to for adding the packet filtering rule Click Cancel to exit from this page without saving the changes 144 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Add a packet filtering rule Allows to ceate a packet filtering rule thereby conforming traffic is denied access Ingress Interface Any bl Exclude Egress Interface Exclude IP Version PvE IPv Destination Address n Exclude IPv6 Source Address n _ Exclude Protocol Any w Exclude Destination Port Exclude Source Port las Exclude Target Enable this rule Figure 4 10 3 2 Add a Packet Filtering Rule for Firewall IPv6 145 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Add a Packet Filtering Rule IPv6 page Field Description Ingress Interface To specify the input interface of the packet from dropdown options e g WANI To exclude the selected option IP Source Address To specify the source IP address To specify the range of the source port Valid for protocols TCP or UDP only Destination IP Type The destination IP can be a SINGLE addre
108. ower and Cooling If the POWER indicator does not turn on when the power cord is plugged in you may have a problem with the power Outlet power cord or internal power supply as explained in the previous section However if the unit power is off after running for a while check for loose power connections power losses or surges at the power outlet If you still cannot isolate the problem then the internal power supply may be defective In this case please contact your local dealer Installation Verify that all system components have been properly installed If one or more components appear to be malfunctioning e g the power cord or network cabling test them in an alternate environment where you are sure that all the other components are functioning properly Transmission Mode The transmission mode for RJ45 ports is Giga Ethernet for RJ 11 port is auto negotiation VDSL2 Therefore if the Link signal is disrupted e g by unplugging the network cable and plugging it back in again or by resetting the power the port will try to reestablish communications with the attached device via auto negotiation If auto negotiation fails then communications are set to half duplex by default Based on this type of commercial standard connection policy if you are using a full duplex device that does not support auto negotiation communications can be easily lost i e reset to the wrong mode whenever the attached device is reset or experiences a power fluc
109. pre selected levels of logs are viewed alH Debug and above levels of logs are viewed WH Informative and above level of logs are viewed Ni Notice type and above level of logs are viewed lle Warning type and above levels of logs are viewed Sigel Error type and above levels of logs are viewed el i e 18 Critical type and above levels of logs are viewed NG Alert type and above level of logs are viewed 118 Emergency type of log information is viewed Click Save Changes to configure the system log settings Click View Log to fetch the logs in browser When you click View log button a screen is displayed as shown in Figure 4 3 7 1 This screen is an example of system log of default level as shown in the browser Configure System Log Filter Level View System Log 9 HHH HHH H ZH HL 49 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel System Log Nov 29 22 07 30 none daemon debug mini_httpd 1663 ifx_get_FirmwareVer 1439 fw version 5 4 8 0 0 6 5 4 4 4 0 1 5 4 8 0 0 6 5 4 4 4 0 1 length 49 Nov 29 22 07 40 none daemon debug mini_httpd 1663 ifx_get_FirmwareVer 1439 fw version 5 4 8 0 0 6 5 4 4 4 0 1 5 4 8 0 0 6 5 4 4 4 0 1 length 49 Nov 29 23 34 50 none daemon info mini_httpd 1663 ifx_AuthHandler_ptr failed Nov 29 23 34 50 none daemon info mini_httpd 1663 ifx_AuthHandler_ptr failed Now 29 23 34 54 none daemon err mini_httpd 1663 ifx_get_wan_ip
110. priate server located at another internal IP address You can add maximum of 16 entries Application Trigger Trigger Trigger External External Open Enable Name Start Port End Port Protocol Start Port End Port Protocol Qin Figure 4 11 3 Port Triggering 171 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Port Triggering Field Description Click Cancel to exit from this page without saving the changes 172 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 173 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel When you click the Add button in the Port Triggering page a screen is displayed as shown in Figure 4 11 3 1 Configure Port Triggering Some applications such as games video conferencing remote access applications and others require that specific ports in the Router s firewall be opened for access by the applications You can configure the port settings from this screen by selecting an existing application or creating your own Custom application and click Savel Appi to add Application Name Select an application Select One v Custom application Trigger Port Trigger Port Trigger Open Port Open Port Open Enable _ Start End Protocol Start End a er E Figure 4 11 3 1
111. r IEEE 802 11 wireless networks Introduced as part of the original 802 11 standard ratified in September 1999 its intention was to provide data confidentiality comparable to that of a traditional wired network WEP recognizable by the key of 10 or 26 hexadecimal digits was at one time widely in use and was often the first security choice presented to users by router configuration tools m What is WPA Wi Fi Protected Access WPA and Wi Fi Protected Access II WPA2 are two security protocols and security certification programs developed by the Wi Fi Alliance to secure wireless computer networks The Alliance defined these in response to serious weaknesses researchers had found in the previous system WEP Wired Equivalent Privacy WPA sometimes referred to as the draft IEEE 802 111 standard became available in 2003 The Wi Fi Alliance intended it as an intermediate measure in anticipation of the availability of the more secure and complex WPA2 WPA2 became available in 2004 and is common shorthand for the full IEEE 802 111 or IEEE 802 11i 2004 standard A flaw in a feature added to Wi Fi called Wi Fi Protected Setup allows WPA and WPA2 security to be bypassed and effectively broken in many situations WPA and WPA2 security implemented without using the Wi Fi Protected Setup feature are unaffected by the security vulnerability 16 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 01 ETA EA Ha
112. rdware Description This section describes the important parts of the wireless VDSL2 router It features the front and rear panel Wireless Router Outward 17 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 3 1 Front Panel The front panel provides a simple interface monitoring of the router Figure 3 1 shows the front panel of the wireless router Wireless PWR E1 E2 E3 E4 LINK WPS WLAN VDSL2 Router E E E m E E b LAN WAN Figure 3 1 wireless router Front Panel 3 2 Front Indicators The wireless router has Eight LED indicators The following Table shows the description Table 3 1 Table 3 1 LED Indicators Description and Operation LED PWR Power LED E1 E4 Ethernet LED Color Status Descriptions On Steady The device has a good Ethernet connection The device is sending or receiving data Slow Blinking The Internet or network connection is down LINK VDSL2 LED 18 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Color Status Descriptions On Steady The WPS connection is ready The WPS is not available or WPS is not enabled or initialized On Steady Wireless access point is ready WLAN Data is being transmitted through WLAN Wireless LED Wireless access point is off or has malfunctioned Note 1 It is normal for the connection between two Routers to take up to 3 minute
113. ress of the remote tunnel endpoint When you select Dynamic mode this field is disabled Subnet Mask IPv4 Address subnet mask DS Lite Remote IPv6 address Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 212 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 15 Diagnostics When clicking on the Diagnostics link on the left navigation bar of the wireless router CPE homepage The menu below includes the sub menus of MEETS The following options are available under Diagnostics as shown in Figure 4 15 Diagnostics gt Diagnostic Test Suite Figure 4 15 Diagnostics Options 213 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 15 1 Diagnostic Test Suite For configuring the Diagnostic Test Suite settings click the Diagnostic Test Suite link Diagnostics gt Diagnostic Test Suite on the left navigation bar A screen is displayed as shown in Figure 4 15 1 Diagnostic Test Suite This page allows you to diagnose LAN and WAN connectivity of the system Physical Link Status WAN Down LAN 1 Down LAN 2 Down LAN 3 Up LAN 4 Up Testing LAN connection Pass Testing Internet Connectivity Ping to Gateway Fail Ping to Primary DNS Fail Start Diagnostics Test MS Figure 4 15 1 Diagnostic Test Suite 214
114. rvice request to the appropriate server located at another internal IP address Public Public Application Private name IP Start End Port Port Skype UDP at 1 192 168 16 21 31082 192 168 16 21 31082 UDP 31082 Dynamic ur 2382 Skype TCP at De 2 192 168 16 21 31082 192 168 16 71 31082 TCP 31082 WANPPP 14 Dynamic rea 2382 Skype UDP at 3 192 168 16 16 49285 192 168 16 16 40285 UDP 492485 WANPPP1 Dynamic g 2382 Skype TCP at i 4 194 168 16 16 49285 192 168 16 16 i 40285 TCP 40285 WANPPPI Dynamic g 2382 Figure 4 11 2 Virtual Server 165 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Virtual Server Page Field Description Click Add to add a Virtual Server entry 166 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 167 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel When you click the Add button in the Virtual Server page a screen opens with a new web page as shown in Figure 4 10 2 1 Configure Virtual Server Configure the CPE device as a Virtual Server so that external service requests can be redirected to the internal Servers such as FTP or WEB Select an application Select one Custom application I Protocol Tc
115. ry DNS fc00 1 Secondary DNS E DNS Domain name Jantig com Prefix Delegated Figure 4 7 2 4 LAN Settings IPv6 Tab Option 3 Statefull DHCPv6 Server For LAN interface the wireless router uses SLAAC based prefix assignment to LAN hosts The IPv6 prefix obtained from DHCPv6 on WAN is automatically passed to LAN hosts for their IPv6 address configuration The screen contains the following details 110 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Fields in LAN Settings IPv6 Field Description LAN IPv6 Configuration IPv6 Address IPv6 Address of CPE IPv6 Address Auto configuration Auto Configuration Mode on LAN interface for LAN hosts Stateless Auto Config SLAAC Auto Configuration Mode Statefull DHCPv6 Stateless Auto Config SLAAC Statefull DHCPv6 Stateless Address Auto configuration Stateless Address Auto configuration Prefix Prefix Length IPv6 Prefix and Length Configuration Primary DNS Primary DNS for IPv6 name resolution Statefull DHCPv6 Primary DNS Primary DNSv6 Address Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 111 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel When you click Prefix Delegated view button in the LAN Settings IPv6 page
116. s 42 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 3 4 Web Settings This page shows the details of Web login timeout settings for the CPE device in seconds Click the Web Settings link System gt Web Settings on the left navigation bar and a screen is displayed as shown in Figure 4 3 4 men E _ Web Timeout Settings Set Autologouttime in seconds limit for CPE device Host Name Config Syste 2 ya m Tune Autologout Duration 1800 Administrator Settings Web Settings Software Firmware Upgrade cancer Configuration Settings system Log Figure 4 3 4 Web Settings Fields in Web Settings Description Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 43 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 3 5 Software Firmware Upgrade For updating the system firmware click the Software Firmware Upgrade link System gt Software Firmware Upgrade on the left navigation bar A screen displays the current version of wireless router Software running on the device as shown in Figure 4 3 5 System y l Host Name Config System Time Administrator Settings Web Settings Software Firmware Upgrade z Configuration Settings System Log SSL Certificate Software Firmware Upgrade Specify t
117. s due to VDSL2 CO Router W to establish a link mechanism in auto negotiation that detects and calculates CO and CPE both PBO and PSD level noise levels and other arguments for getting a better connection 2 Every time the user presses the WPS button there will be two minutes of time to detect the available equipment If the WPS function does not detect the device the WPS light will turn off 19 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 3 3 Rear Panel The rear panel provides the physical connectors connected to the power adapter and any other network device Figure 3 2 shows the rear panel of the wireless router LINE PHONE Figure 3 2 Rear Panel 20 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel And the table shows the description Table 3 2 Connectors Gigabit Ethernet E1 E4 Table 3 2 Description of the router rear connectors Type Description The reset button allows users to reboot the VDSL2 or load the default settings Press and hold for 1 5 seconds Reboot the VDSL2 Router Press over 5 seconds Load the default settings Reset Button For connecting to a VDSL2 device Do not use RJ11 and Terminal Block at the same time RJ 45 For connecting an Ethernet equipped device Press this button to make a network connection through WPS WPS function is only supported on windows 7 or above operating systems Ev
118. ss Address Autoconfiguration Stateless DHCPv6 w Stateless Address Autoconfiguration Prefix Prefix length fc00 u f 54 Primary DNS foot DNS Domain name lantig com Prefix Delegated Figure 4 7 2 2 LAN Settings IPv6 Tab Option 1 SLAAC Stateless DHCPv6 108 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel LAN Settings You can configure LAN settings of CPE device such as LAN IP Address and DHCPw6 configuration ie Y IPv6 Address fot 54 Auto Configuration Mode Stateless Address Autoconfiguration Stateless Address Autoconfiguration Prefix Prefix length feoo sd f ea Secondary DNS FE Prefix Delegated Figure 4 7 2 3 LAN Settings IPv6 Tab Option 2 SLAAC 109 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel LAN Settings You can configure LAN settings of CPE device such as LAN IP Address and DHCPv6 configuration LAN IPv6 Configuration IPv Address tc00 1 o a IPv6 Address Auto Configuration Auto Configuration Mode Statefull DHCP V6 o E Statefull DHCPv6 IPv6 Pool Start Address lfc00 100 IFv6 Pool End Address 1000 20 o Prima
119. ss or a SUBNET or All involving a range of IP addresses The available options are Drop Reject and Accept Click Apply at any time during configuration to for adding the packet filtering rule Click Cancel to exit from this page without saving the changes 146 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 Packet Filtering configuration example 1 Packet Filter configuration procedures 1 All devices must be connected and turned on 2 Confirm that the wireless router is in router mode default mode 3 If there is not router mode please refer to the following configuration diagram to configure the router mode and packet filter 4 All the configuration arguments are for reference only 2 Router mode configuration 9 WAN setting WAN The CPE device can be connected to your service provider in any of the following ways WAN Mode Selection Auto Detect Config Attached Channel WAN Channel Config WAN TYPE VLAN Channel Config WAN Setting WAN Status DNS IP address assigned by your ISP 192 168 116 1204 la ae Subnet Wek 255 25s aes BEN Cannot ISP Gateway Address 192 hes i he Eo Default WAN 147 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Configure example WAN WAN Setting Items Setting argument Action Attached Channel Default IP address assigned
120. sue please contact your local vendor 3 Do not use sub standard power supply Before connecting the power supply to the device be sure to check compliance with the specifications The wireless router uses a DC12V 1A power supply 4 The power supply included in the package is commercial grade Do not use in industrial grade applications 5 Please look for the QR code on the bottom of the product the user can launch the QR code scanning program to scan and download the user s manual electronic format file VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel ETA Installing the Router 2 1 Hardware Installation This chapter describes how to install the router and establish the network connections The wireless router may be installed on any level surface e g a table or shelf However please take note of the following minimum site requirements before you begin The wireless router has pre installed two rubber feet and two 2dBi Antenna 2 4 GHz 2 2 Pre installation Requirements Before you start the actual hardware installation make sure you can provide the right operating environment including power requirements sufficient physical space and proximity to other network devices that are to be connected Verify the following installation requirements Power requirements DC 12 V 1A The router should be located in a cool dry place with at least 10cm 4in of space at the front and back for v
121. t Switch und Access Point Telekom VDSL2 kompatibel 4 6 5 5 Bridge The option Bridge enables the bridge mode which is a common connection method used for xDSL modem Select this option on WAN Settings page and click Apply A screen is displayed as shown in Figure 4 6 5 7 WAN The CPE device can be connected to your service provider in any of the following ways Attached Channel D pimo 4 vi WAN TYPE Bridge N Default WAN Figure 4 6 5 7 Bridge WAN Setting 86 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Bridge Configuration Description Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 4 6 5 6 Delete This option allows deleting the selected configured WAN connection This makes WAN connections free to re choose the type of protocol and other parameters configuration Click Cancel to exit from this page without saving the changes Click Apply for deleting the WAN connection 87 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 88 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 6 WAN Status For displaying the status report of VCCs click the WAN Status link WAN gt WAN Status on the left navigati
122. t Switch und Access Point Telekom VDSL2 kompatibel 4 9 2 Security Settings The Security Settings page presents Wireless Security related settings For viewing the wireless security related settings click the Security Settings link Wireless gt Security Settings on the left navigation bar A screen is displayed as shown in Figure 4 9 2 WLAN Security Settings AP WAP related security configuration settings SSID Encryption Type WPA2 PSK Authentication Type Personal w Algorithm Type AES WPA WPA2 Settings Re Key Interval 13600 Fre Shared key PAS Figure 4 9 2 WLAN Security Settings 128 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Security Setting Field Description SSID Presents configured SSID security Selection SAR OS Select Encryption Type for the chosen beacon type Each encryption mode will u dl bring out different web page and ask you to offer additional configuration e Encryption Type Basic Algorithm Type None Wireless open Encryption Type Basic Algorithm Type None Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes Encryption Type Basic Algorithm Type WEP 129 VC 400RTW VDSL2 Slave Modem Router mit Switch und
123. tegories AC_BE AC_BK AC_VI and AC_VO for WMM APSD automatic power save delivery is an enhancement over the power save mechanisms supported by Wi Fi networks It allows devices to take more time in sleeping state and consume less power to improve the performance by minimizing transmission latency When you click WMM Settings link Wireless gt WMM Settings on the left navigation bar a screen is displayed as shown in Figure 4 9 3 WLAN WMM Settings AP VAP related WMM configuration settings SSID WMM U APSD Activation Deactivation WMM Support Power Save Mode U APSD a WMM AP parameters __ ESTI ETT IO Txop __ AdmissionControljAckPolic ED lp be O O acka dbo lr m m Ac vi 3 E ll les m m AC VO 2 JE ik ler m a ea WMM STA parameters Ecowmin Eowmax asn oP APOLO AC_BE 4 IE B Mo O ac ekfa dh hi oo m acsi e e da O AC_VO 2 E 2 Vaz O Figure 4 9 3 WLAN WMM Settings 133 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in WMM Setting Field Description SSID SSID information presented in R O format for AP VAP selected WMM Support Enable or Disable of WMM Exponential of Contention Window minimum
124. ter The options available are Disable Server and Relay Agent The default value is Disable If DHCP Mode is set to Server there are some additional options available which are shown in Figure 4 7 2 IP Pool Starting Address To enter the starting IP Address of the DHCP server pool IP Pool Ending Address To enter the ending IP Address of the DHCP server pool Lease Time To specify the lease period for DHCP allocation Local Domain Name optional To enter the Domain Name of the DHCP server DHCP Server IP IP address of the DHCP server on the interface is shown to which the DHCP requests are relayed DHCP Mode 104 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Field Description DHCP Mode DHCP Server IF Pool Starting Address 1 DHCP Server iS IF Pool Ending Address 192 168 Mk lease Time Half hour Local Domain Name dsigw lantig com optional IP Pool Starting Address DHCPv4 pool starting IPv4 address Lease Time for every DHCP leased entry Select from dropdown of allowed values Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 105 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel When you click the Click Here link under IP Address Reservation in the LAN Settings page a s
125. the left navigation bar A screen is displayed as shown in Figure 4 10 1 Firewall Setting The CPE device provides extensive firewall protection against a wide array of common hacker attacks This is done by restricting connection parameters to limit the risk of intrusion Enable Disable Figure 4 10 1 Firewall Setting The screen contains the following details Fields in Firewall Setting Description Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 138 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 10 2 IPv6 Firewall Setting For enabling or disabling the IPv6 firewall click the IPV6 Firewall Setting link Firewall gt IPv6 Firewall Setting on the left navigation bar A screen is displayed as shown in Figure 4 10 2 IPv6 Firewall Settings IPv6 Firewall Settings You can configure IPv6 firewall settings You can configure IPv6 firewall settings Firewall Mode 1 Rules to block fc00 in forwarding path 2 Rules to allow only active prefix from LAN to WAN and from WAN to LAN 3 Rule to block everything elsefe g Invalid prefix expired prefix 22 2 2222 2 2 www ww www ww ww 2 gt 2 ww 2 www ww 2 2 www ww 2 www ww gt www 2 2 ww www 2 2 ww ww ww 2 ww 2 2 2 2 gt ww ww 2 22 zz cr TSE 2 2 gt gt 2 OE E gt gt gt 22 gt gt gt gt
126. thod Click Start PBC then start PBC on the device you want to connect to the router within two minutes Start PBC Figure 4 9 4 WPS Settings 135 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in WPS Setting Description Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes Note WPS Function is only supported by windows 7 or above or any operating system that supports WPS function 136 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 10 Select Firewall You can view Firewall link on the left navigation bar of the wireless router CPE homepage The menu below includes the sub menus of MENE IESO A tigen EUR dali Uli Toe ed 1 MOT 1120 AVelelirer iilela SIT Te and ACL Following are the options available under Firewall as shown in Figure 4 10 Firewall Firewall Setting IPv6 Firewall Setting Packet Filtering URL Filtering Parental Control Application Server Settings ACL Figure 4 10 Firewall Options 137 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 10 1 Firewall Setting For enabling or disabling the firewall click the Firewall Setting link Firewall gt Firewall Setting on
127. to 300 Mbps and extend the coverage wireless router also supports one touch Wi Fi Protected Setup WPS with the push button that only takes a few seconds to setup a secured wireless network In recent years the market for wireless communications has enjoyed tremendous growth Wireless technology now reaches or is capable of reaching virtually every location on the surface of the earth Hundreds of millions of people exchange information every day via wireless communication products Anyone can bring a built in WLAN client smartphone tablet or notebook into a meeting room for a conference without laying a clot of LAN cable or drilling holes everywhere Wireless LAN enables high mobility so WLAN users can simultaneously access all LAN facilities just like on a wired LAN as well as Internet access The wireless router is equipped with a wireless LAN interface compliant with the standard IEEE 802 11n protocol To boost its performance even further the wireless router is also loaded with an advanced wireless technology to lift up the data rate up to 300 Mbps You can finally smoothly enjoy a wide range of apps on your smart phone tablet or smart TV 5 The maximum wireless data transfer rate is derived from IEEE Standard 802 11 specifications Actual data transfer rate will vary from network environment including distance network traffic building site materials construction interference from other wireless devices and other adverse conditions
128. tuation the best way to resolve this problem is to upgrade these devices to a version that support Ethernet and VDSL 232 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel Physical Configuration lf problems occur after altering the network configuration restore the original connections and try to track the problem down by implementing the new changes one step at a time Ensure that cable distances and other physical aspects of the installation do not exceed recommendations System Integrity As a last resort verify the switch integrity with a power on reset Turn the power to the switch off and then on several times If the problem still persists and you have completed all the preceding diagnoses then contact your dealer NT gt E h Compliance Information FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a computing device pursuant to Part 15 of FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to ra
129. um NGN 3G Signaling 36 0x24 144 0x90 3 High AF43 NGN 3G Signaling 100 110 38 0x26 152 0x98 101 ee S NGN 3G voice 101 110 46 0x2e 184 0xb8 MAEN WOK 110 Protocol 110 100 48 0x30 192 0xc0 Control SIMON 7 an CS7 Protocol 111 000 56 0x38 224 0xe0 Control 183 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 11 2 Queue Configuration For configuring the Queue Configuration click the Queue Config link QoS gt Queue Config on the left navigation bar A screen is displayed as shown in Figure 4 11 2 WAN Egress Queue Configuration Configure queues in CPE device to be used for QoS controlled traffic flows The queue entries configured here will be used by classifier to place packets appropriately Ma me DOWNSTREAM Queue Queue Drop Committed Peak Enable Action Name Precedence Algorithm Shaping Rate Shaping Rate DT 0 Yes O def gueue E SP 0 60000 ql 1 DT SF 0 0 60000 Yes O qe 2 DT SF 0 0 60000 Yes O Figure 4 11 2 Queue Configuration 184 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in Queue Configuration Upstream Field Description pi Selection tab for upstream downstream Queue configuration Precedence of Queue Lower values denote higher priority Precedence Scheduler This is the queue scheduling algorithm used for the queue The supp
130. unnel b m WAN Interface selectinterface w Configuration Modes MTU min 1280 NOTE MTU 1280 is recommended while connecting to Internet 6RD Comcast etc as per RFC 2460 Section 5 Packet Size Issues Otherwise to get default MTU leave this field blank Static Parameters 6RD Prefix DO 6RD Prefix Length OCO IL 6RD BR IF IPv4 Mask Length ro A A Figure 4 14 2 6RD Configuration 209 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in 6RD Configuration Field Description General Settings Enable 6RD tunnel To enable or disable 6RD functionality in CPE oia Select dynamic 6RD tunnel through DHCP option or static tunnel configuration Static Parameters 6RD Prefix 6RD Prefix string 6RD BR IP 6RD Border Relay s IPv4 address Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 210 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 14 3 DS Lite Configuration The wireless router supports DS Lite configuration mechanism For configuring the Ds Lite configuration click the DS Lite configuration link IPv6 gt DS Lite Configuration on the
131. wn in Figure 4 1 2 5 The WLAN tab allows the user to configure the Wireless LAN in VC 400RTW Quick Configuration of WLAN AP Settings The same settings needs to be done in stations also anses UNTER WLAN AP Setup WLAN Radio Enable SSID N VEOOW WPA_WPA2_Mixed security Type Passphrase ml Configure Figure 4 1 2 5 WLAN Setup 34 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel The screen contains the following details Fields in WAN setup Static IP Field Description WLAN AP Setup WLAN Radio Enable To Enable or Disable WLAN feature in CPE Security Type for AP are m Basic non 11n mode m WPA non 11n mode Security Type Click Configure to configure the Wireless LAN AP in CPE device 35 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 2 Select the Menu Level There is an easy Setup for end users at the setup of wireless router with SYSTEMI Statistics xDSLI WANIJ LANI RouteQWireless FIREWALLSNATHOoS Multicast iPseciPv6 Diagnosticsgauick Setup Homel ogouthigy more detailed configurations System ir Statistics j Version Information xDSL gt Software Version B 1 WAN DSL Firmware version 5 4 8 0 0 6 5 4 4 5 1 2 Lan Connected Standard DSL 304 Wireless gt Modem Status SHOWTIME SYNC Firewall NAT Wan Mode VDSL PTM QoS gt Link Status CONNECTED Multicast IP Ad
132. y Point to Point Protocol over ATM used for connecting to the ISP click Apply This setting is applicable only for ATM WAN mode Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 76 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 5 1 Dynamic IP Address To configure the WAN interface of DHCP IP type select Dynamic IP Address option A screen is displayed as shown in Figure 4 6 5 3 WAN The CPE device can be connected to your service provider in any of the following ways Attached Channel 1 ptm0 201 e WAN TYPE Dynamic IP Address ig Address Version IPv4 IPv6 WAN IPv6 Configuration Configuration Modes Stateful DHCPVS 14_NA and lA_PD DUID Type Type 1 LLT Link Layer Time IANA ID lo IAPD ID SLA ID 0 Rapid Commit Default WAN A AA A Figure 4 6 5 3 Dynamic IP Address T1 VC 400RTW VDSL2 Slave Modem Router mit Switch und Access Point Telekom VDSL2 kompatibel 4 6 5 2 Static IP Address To configure the WAN interface to use a static IP address select the option Static IP Address in the WAN Settings screen A screen is displayed as shown in Figure 4 6 5 4 WAN The CPE device can be connected to your service provider in any of the following ways Attached Channel 1 ptm0 201 WAN TYPE Static Address y Address Versio

USER'S MANUAL VC

Contents

Download Pdf Manuals

Related Search

Related Contents