IC602 User Manual - CONRAD Produktinfo.
Contents
1. Subnet mask Default gateway and DNS server to let the network work All these settings must be correct for your network environment otherwise the IP CAM can not work The default setting is Obtain an IP address automatically 16 StarVedia Outdoor Day amp night IP Camera Seeing the video from anywhere Network Settings For wired ethernet 5 Information Obtain an IP address automatically ls Network IP address 192 168 1 123 Wired Network Subnet mask 255 255 255 0 Advanced Default gateway 192 168 1 Video Obtain DNS server address automatically gt Schedule Use the following DNS server address Preferred DNS server 168 95 1 1 Admin Alternate DNS server 1688 las 192 Krt English Save amp Apply Figure 3 6 Network settings page for fixed IP address StarVedia Outdoor Day amp night IP Camera 3 4 Advanced Network In some special situation your network environment only provides PPPoE connection ADSL service there is no NAT router available You will then need to set the PPPoE settings in the Advanced Network page Only the PPPoE username and password are needed to let PPPoE work After the Save amp Apply button is pressed the PPPoE function will work immediately You can check the Registration status in the Information page to see if the2. Admin English Figure 3 12 DI DO Settings page 25 StarVedia Outdoor Day amp night IP Camera 3 9 NAS settings The IP Camera provides the recording of the video files into a standard NAS Network Access Storage device The IP camera connects to the NAS device using the standard LMX_NS CIFS SSN protocols that are the same as the Microsoft Windows network neighborhood protocols This makes the IP camera easily record the video files to all the standard NAS devices in the market Since there are a lot of different choices including prices and scales users can decide by themselves which is best for their needs By using this function the standard NAS device is becoming a NVR Network Video Recorder device Notice when the IP camera is doing NAS recording this is counted as one video user Please refer to appendix B about allowed maximum video users 1 If the Always Recording is selected the system will start to record to the NAS storage device immediately and keep recording always If the Schedule Recording is selected the system will do the NAS recording according to the scheduling in section 3 10 Disable Recording will disable this NAS recording 2 When doing the NAS recording the system will check the free disk space of the NAS device If the free disk space is less than the specified number the system will do Circular recording overwrite the oldest recorded files of this ip ca
3. F Schedule Admin Language English Figure 3 4 Video display page 15 StarVedia Outdoor Day amp night IP Camera 3 3 Network The Network page allows you to modify the network settings of the wired Ethernet The default settings use DHCP to obtain an IP address automatically In most of the home and office network environment there is DHCP server running In this situation by using this default settings the IP CAM can work immediately in most of the time If the Ethernet cable is unplugged the CAM will lose connection But as soon as the Ethernet cable is plugged in again the IP CAM will obtain a new IP address immediately Seeing the video from anywhere Network Settings For wired ethernet Information Obtain an IP address automatically 5 Network Use the following IP address IP address 4 Wired Network Advanced Subnet mask Default gateway gt Video 9 Obtain DNS server address automatically gt Schedule Use the following DNS server address Preferred DNS server 168 Admin Alternate DNS server lt English Save amp Apply Figure 3 5 Network settings page for DHCP function If the network environment does not support DHCP function you will need to set the network settings of the IP CAM manually Please fill all the fields including IP address
4. What should I do if the password is forgotten and ID password card is missing The easiest way to solve this problem is to reset the IP Cam to the factory default Please press the reset button on the cable of the IP Cam for more than 4 seconds and release it The IP Cam will then restart to the factory default The default administrator account is admin administrator password is empty The default video play password is ipcam You can adjust these account and passwords by using the browser to login into the IP Cam and do the needed modifications can see the video a remote place but the video quality is not good and sometimes the video will disconnect and then the video will reconnect again by itself probably because the internet bandwidth internet speed is not big enough Please try to apply for a better internet connection from your Internet Service Provider or decrease the bandwidth settings of the IP Cam You can adjust the bandwidth requirement of the IP Cam either from the CamView software or login into the web configuration page of the IP Cam to do the modification Does the IP Cam provide the recording function You can do the recording of the video audio of the IP Cam from the CamView software with the CamView software You can also do the video audio recording to the standard NAS storage device Another software CamPlay is needed to playback the recorded vide audio files Can connect the IP c
5. Email ftp alarm settings and or the NAS settings 1 Schedule list all the scheduling are listed in this area Each listed item can be modified or deleted by pressing the Edit or Delete button 2 Email ftp Alarm for each scheduling if this is selected and the Motion triggered and or D I triggered is enabled the IP camera will trigger the email ftp sending in the scheduled time period when the video motion is detected and or digital input alarm is detected 3 NAS Record for each scheduling if this is selected either Continuous or Motion triggered or D I triggered could be enabled For Continuous it means that the IP camera will do the video recording to the NAS device during the whole scheduled period For Motion triggered and or D I triggered it means that the IP camera will do the video recording to the NAS device for 30 seconds during the scheduled period each time when the video motion is detected and or digital input alarm is detected 4 Forthe scheduling period can choose between Every week Every day or Fixed time A For Every week can choose week days of the week and set the time duration of each day B For Every day can set the time duration of every day for the scheduling C For Fixed time can set the starting date time and the end date time of the scheduling period 28 StarVedia Outdoor Day amp night IP Camera Seeing the video from anywhere Schedule
6. Quality AUR Brightness 5 medium Sharpness 5 medium English Low light sensitivity high Video color colored Outdoor video Indoor video Indoor tSun light 60Hz light freq 50Hz light freq 4 gt Figure 3 8 Video settings page 20 StarVedia Outdoor Day amp night IP Camera 3GPP RTSP settings The IP CAM is able to be viewed from a mobile phone for detailed settings on the 3G mobile phone please refer to Appendix E Users can disable the 3G mobile access ability in this page After the 3GPP RTSP feature is disabled no 3G mobile phone is allowed to access the video of the IP camera When this is disabled the rtsp stream with MPEG2 audio is still working please refer to Appendix F for more details about rtsp stream with MPEG2 audio When the 3GPP is enabled the video frame rate resolution and bandwidth for 3G mobile access could be set independently from the video settings for CamView PC access The maximum allowed resolution is 352x255 and maximum allowed bandwidth is 256 kbps The Access URL line is the url address for 3G mobile phone to input for seeing the video of the IP camera Different 3G mobile may need to input this url in different way detailed information could be found in the user manual of different mobiles Please be noticed that usually public IP address is needed for the IP camera so that the 3G mobile could access the IP camera s video The defa
7. SETTINGS sitate etat ipe Mtas elan 26 210 SCHEDULING tn 28 Seide DATE TIME toten enten aen 30 Selen eiue dee 31 3 13 UPGRADE cece cece cccccccccccccccccccccccccccsceccccuuuceccccsucecccsuececcceuccececeuaeeccecuuceseceuauceseeceaees 32 CR MEE izle RE A 34 192 SAFE roit oc can aolet 35 3 16 SET TO FACTORY 22 220 0000000000000000000 36 4 FEATURES AND SPECIFICATIONS cccccccsssscccccsssscccccssccccccccsccccccccscccccsceeccccces 37 4 1 FEMURES RR TM HET 37 4 2 220 0 0 0000000000 38 5 PACKAGE GONTENTS 40 FIGURE 5 7 INSTALLATION CD APPENDIX A LIST OF TESTED NAT ROUTER DEVICES 40 APPENDIX LIST OF TESTED NAT ROUTER DEVICES ee ooose eenen 41 APPENDIX B MAXIMUM ALLOWED VIDEO USERS eee oeeeeeescooceees 42 APPENDIX C PERFORMANCE INFORMATION 43 APPEN
8. is registered using the PPPoE connection Please be noticed that the DHCP or static IP settings in the Network page can work together with the PPPoE connection Only that the PPPoE has higher priority so if the PPPoE is working the IP will use PPPoE to connect to the Internet The default setting is Disable PPPoE Seeing the video from anywhere Advanced Network Settings Information 9 Disable PPPoE P Network Use PPPoE to get an IP address Username Wired Network Password Advanced save amp Apply Video Schedule Admin Language English Figure 3 7 Advanced network settings page 18 StarVedia Outdoor Day amp night IP Camera 3 5 Video Settings The is designed to provide high quality video for viewing from CamView software In this page you cam modify some settings related to the video viewing 1 Password play video this is the password needed for viewing the video from the CamView software Together with the CAM ID you can view the video of this IP CAM anywhere in the world through the Internet 2 Internet speed this is the Internet bandwidth of your network environment Higher value will generate higher video quality But if your internet connection can not provide more bandwidth than the specified value the video quality could degrade So please key in a value that is lower than your internet bandwidth 3 Select resolution amp frame rat
9. CamView program to see the video Figure 2 5 is the running window of the CamView program If the computer and CAM is connected to the same network the ID will be displayed in the 10 StarVedia Outdoor Day amp night IP Camera Auto Search list You can double click the Auto Search to search all the connected 5 any time The only thing left right now for seeing the video is to double click the IP ID item in the Auto Search list For example if the ID is 001 001 029 you can then double click the 001001029 item in the Auto Search list to view the video A window asking for password input will pop up Please key in the password in your ID Password card into this field and click ok The video will then be displayed on the window Figure 2 4 The ID Password card Notice 1 You can modify this play video password by entering into the web configuration pages Please refer to section 3 6 for more information 2 You also add the IP into the CameraList in the CamView software to have more convenient video display please refer to the user manual of the CamView software for more functions Seeing the video in a remote location After the IP is installed and you can see the video from the CamView software in the local network it s very easy to see the video a remote location All you need to do is add a camera item in CameraList fold
10. DIX D TROUBLE SHOOT ING eene eese eee 44 APPENDIX E 3GPP ISMA OPERATION eee eee e e eere eene eee o e eerte ee ns eate teet ee 45 StarVedia Outdoor Day amp night IP Camera APPENDIX F THIRD PARTY AND EMBEDDED WEB PAGE INTEGRATION StarVedia Outdoor Day amp night IP Camera List of Figures and Tables Figure 2 1 Major components of the IP camera Figure 2 2 IP connection diagram Figure 2 3 The installation CD disk Figure 2 4 The ID Password card Figure 2 5 Running window of CamView program Figure 2 6 Pop up play video password window Figure 3 1 Open the web configuration page from CamView software Figure 3 2 IP CAM Web configuration login page Figure 3 3 IP CAM Information page Figure 3 4 Video display page Figure 3 5 Network settings page for DHCP function Figure 3 6 Network settings page for fixed IP address Figure 3 7 Advanced network settings page Figure 3 8 Video settings page Figure 3 9 SGPP RTSP enabled page Figure 3 10 Night mode control page Figure 3 11 Email FTP Alarm page Figure 3 12 DI DO Settings page Figure 3 13 NAS Storage settings page Figure 3 14 Schedule Management page Figure 3 15 System date time settings page Figure 3 16 Admin settings page Figure 3 17 Firmware upgrade settings page Figure 3 18 Firmware upgrade st
11. FTP DHCP UPnP ARP DNS PPPOE etc Power adaptor camera bracket RJ45 ethernet cable quick installation guide CD with installation tool software and User s Manual ID Password card Surveillance application for viewing and archiving up to 16 cameras Up to 20 simultaneous unicast users please see appendix B Unlimited users using multicast Events triggered by video motion detection Notification upload of JPEG images over FTP and or email 130 x 77 x 78 mm 498 g exclude camera bracket exclude power adaptor CE FCC Part 15 Subpart B Class B Wireless RF CE FCC Part 15 Subpart C Power supply UL EN 60950 20 60 C Humidity 20 80 RH non condensing 39 StarVedia Outdoor Day amp night IP Camera 5 Package contents M Figure 5 3 Bracket Quick Installation Guide tand Producti Via CamView Application User Manual Adobe Reader Figure 5 7 Installation CD Figure 5 2 Power Adaptor Figure 5 4 Ethernet cable ID Password 4 fF Ga Figure 5 6 ID Password Card 40 StarVedia Outdoor Day amp night IP Camera Appendix List of Tested NAT router Devices The followings are the list of tested NAT router devices that can work with the IP CAM and CamView software when viewing in a remote location You do not need to do any modification on the default settings of the NAT routers In some office environment if some strict firewall function is enabled it
12. Management La Information Email ftp Alarm Motion triggered ODA triggered Network MINAS Record Continuous Motion triggered ODA triggered B video Every week Sun Mon Tue Wed Thu Fri Sat O Every day During time 0 100 F Schedule ro sl oe man Start time 2009 v 02 w 05 16 v 00 v veo Endtime 2009 w 02 705 v 16 00 wl Email ftp Alarm m NAS Settings Scheduling Admin Language English Figure 3 14 Schedule management page StarVedia Outdoor Day amp night IP Camera 3 11 Date Time The can synchronize the date time with the universally available time server for example stdtime gov tw through NTP protocol The date time will then be corrected with the time server anytime when the Internet is connected Users can choose the different TimeZone of their areas to display the correct time For some TimeZone areas the Daylight Saving Time could be enabled or disabled When the Daylight Saving Time is enabled the start and stop time of the Daylight Saving Time could be edited Seeing the video from anywhere NTP Date Time Settings Information Network NTP Server Video Time Zone GMT 05 00 Eastern Time USA amp Canada Y Schedule Enable Disable Daylight Saving Tune Start time Second Sunday March Hak End tune First M Sunday v in Wees og
13. Outdoor Day amp Night IP Camera 1 602 User Manual StarVedia Technology Inc http www starvedia com Revision 020205 Date 2009 04 21 Copyright StarVedia Technology Inc 2009 For firmware version 020205 StarVedia Outdoor Day amp night IP Camera Table of Contents de INTRODUCTION er 6 2 HARDWARE DESCRIPTION AND QUICK INSTALLATION USAQGE 8 2 1 MAJOR HARDWARE COMPONENTS csccccccccceccccccccecccccccscecccccaccecceceucecceccaceececeaaesess 8 2 2 QUICK INSTALLATION AND USAGE 22 00 000000000000 00200000001 9 3 13 3 1 2 14 3 2 VIDEO DISPLAY ennn 15 3 3 NETWORKS oM dea E 16 3 4 ADVANCED NETWOBK o rie te doe ERE UR ecu 18 3 5 VIDEO 65 222 22 2 4 008000 00000000000000 0202000000 ssa a rese ss aret essa rre 19 3 6 NIGHT MODE CONTROL 2 22000000000000000000000 22 3 7 PEINT ERR KU 23 3 8 DIDO SEEINGS tumen 25 3 9 NAS
14. amView software only when the IP CAM is registered If this is not registered please check the Ethernet wiring of your network environment The Network type field displays the network connection wired or wireless and method DHCP PPPoE or static ip the is running The Video users field displays the number of connected video viewing users Seeing the video from anywhere IP CAM Information _ tntormation Model wired 020201 IP CAM ID 001 037 091 gt Network Registration status Registered 5 Network type Wired DHCP Gp 10 10 10 173 Y Video Video user 0 vo Video resolution 640 x 480 Video bandwidth 512K bps 5 Admin Email ftp Alarm On NAS Record Not Recording MIT English Mac Address Hex 00 1 7 00 24 5 Figure 3 3 CAM Information page 14 StarVedia Outdoor Day amp night IP Camera 3 2 Video Display This display page allows you to view the video display of the camera For the first time use of this display on a computer an activeX component will be automatically downloaded into the browser This could take some time depends on the internet soeed The component is downloaded from a public domain so that the computer must be connected to the Internet If you want to modify the video display screen size please refer to section 3 6 for more details Seeing the video from anywhere F Information gt Network Video Display Video Settings 3GPP RTSP Night Mode
15. amera directly to my PC notebook with an Ethernet cable If the IP camera is directly connected to your PC notebook computer using an Ethernet cable the IP camera will automatically use an IP address called auto IP with IP address 169 254 xxx xxx If your PC notebook computer is configured to DHCP it will also use an auto IP address But this will take about one minute after the IP camera is connected to the computer and you need to make sure that the WiFi interface on your PC notebook computer is disabled After about one minute you can run the CamView software to access the IP camera the CAM ID should be displayed on the auto search list You can then see the video by double clicking the CAM ID icon But you need to know that in this situation other local or remote computer can not see the video 44 StarVedia Outdoor Day amp night IP Camera Appendix 3GPP ISMA operation 3GPP ISMA is using RTSP protocol for 3G mobile phone to display the video stream from some network devices including IP camera The IC202w support the RTSP protocol and video codec needed by 3GPP ISMA Users only need to access the address rtsp ip address CAM ID password on the 3G mobile phone to access the video of the IP camera No other extra configuration is needed on the IP camera Where ip cam address is the public IP address of the IP camera CAM ID is the unique Camera ID of the specific IP camera Password is the video play password
16. ass and excellent performance It also provides the best bandwidth efficiency offers 640x480 resolution 30 fos frame rate real MPEG4 image compression ability With the very low light sensitive sensor and IR led inside the 1 66 water proof housing the IP Camera can work day and night and satisfy all security and indoor outdoor surveillance needs With the motor controlled IR cut filter the day time video quality is not affected by the infrared light in the sun light The IR cut filter is automatically turned on during dark light The NAS storage function can easily turn any NAS device to a NVR device The schedule function provides full scheduling of email ftp sending motion detection and NAS recording event With the built in Web server the IP Cameras can also be managed from a standard web browser on a Windows computer or a Macintosh The IP Camera provides motion detection function Users can easily setup this function and receive the notification with the snapshot images through email and or ftp when some motion events are detected The IP camera is ideal for securing small businesses home offices and residences over a local area network and or the Internet The differences very easy to see the video of the IP Cam you only need to key in the ID Password of the IP CAM any where in the world you do not need to remember the IP address or domain name or DDNS name or port number And you do not need to modify the sett
17. atus page Figure 3 19 System reboot settings page Figure 3 20 System reboot under going page Figure 3 21 Safe mode information page Figure 3 22 Press the reset button to set to the factory default Figure 5 1 IP Cam body Figure 5 2 Power Adaptor Figure 5 3 Bracket Figure 5 4 Ethernet cable Figure 5 5 Quick installation guide Figure 5 6 ID Password Card Figure 5 7 Installation CD Table A 1 List of tested Wireless AP router devices StarVedia Outdoor Day amp night IP Camera Table A 2 List of tested Wired NAT router devices StarVedia Outdoor Day amp night IP Camera 1 Introduction The IP Network Camera is designed with the user friendly idea deep in mind The user can install the IP Camera easily on his her home network and then access the IP Camera anywhere in the world through the accompanied video management software CamView without setting some complicated DNS name or changing the router s settings It s just a plug amp play action With 3GPP ISMA support users can see the video of the IP camera on any 3G mobile phone anywhere anytime The big difference is that there is software for downloading to the mobile phone so that the fixed IP address is not needed for the IP camera The video settings including frame rate resolution and bandwidth could be different for PC monitoring and mobile viewing For outdoor surveillance and remote monitoring the IP Camera provides the best image quality in its cl
18. d out the email and or ftp with the captured video snapshot B If D I is selected it means that when there is a Digital input alarm detected the system will send out the email and or ftp with the captured video snapshot If the alarm is constantly on the IP camera will keep sending out email ftp message every second for up to 30 seconds If schedule is selected it means that the email ftp alarm detection and triggering will be scheduled by the scheduling in section 3 9 D disable will disable the email ftp alarm 2 Motion sensitivity there are three possible choices in this field High means high sensitivity 1 the detection is triggered by a very small movement in the video image If High is selected and the size of the moving object is larger than about 1 of the whole video area it is detected Please be noticed that the real size of the object could be large or small anyway the detection is only based on the relative size of the object Probably a small pencil moving near the IP CAM could be detected but a moving car far away from the IP CAM could not be detected Low means low sensitivity 1 the detection is triggered by a very large movement If the size of the moving object is larger than about 10 of the whole video area it is detected Median means 3 to trigger the detection 3 Send email message if this item is enabled the IP CAM will send out an email me
19. e automatically you can let the system select the suitable video resolution and frame rate automatically for you The selection is based on the Internet speed value This is the recommended default setting 4 Resolution there are three choices 160x120 320x240 and 640x480 If you decide to choose the value manually you can choose one of the three values But please be noticed that if the Internet speed is slow low value high resolution 640x480 or frame rate could cause very bad video quality 5 Frame rate the video frame display rate Higher value means faster movement and continuity in the video display 6 Favor Preference choose between Video motion and Image quality When the real bandwidth is not enough for the selected Internet speed the system will need to degrade the video motion or image quality This selection will decide if the user want to maintain the video motion or image quality when the internet speed is not good enough Brightness the brightness of the video lower value means darker display Sharpness the sharpness of the video higher value means sharper video 9 Low light sensitivity The low light sensitivity could be normal high or very high When the low light sensitivity is high the system could see better video clearance under low light situation but the moving object will not be very clear under this low light environment Under very dark environment set to very high will g
20. ed in low light environment 4 5 mm F1 9 viewing angle 55 6 fixed iris focus range 30 cm to infinity Day amp night IR lens Motor controlled IR cut filter ICR IP66 grade water resistant 36 IR LEDs for up to 30 m distance night illumination One reset button to factory default settings MPEG 4 Part 2 ISO IEC 14496 2 with motion detection profiles Simple Profile level 0 3 160x120 320x240 640x480 Up to 30 fps in all resolutions MPEG 4 Separate frame rate resolution bandwidth settings for PC and mobile Resolution VGA 640x480 QVGA 320x240 QQVGA 160x120 Bandwidth 64k 128k 256k 512k 768k 1M 1 2M 1 5M bps Frame rate 1 5 10 15 20 25 30 fps Web management username password protection Video display ID password protection Installation tool on CD and Web based configuration Automatic configuration backup and restore Video management software CamView for video access and 38 StarVedia Outdoor Day amp night IP Camera Minimum Web browsing and management software requirements Supported protocols Accessories included Video management software Users Alarm and event management Dimensions HxWxD and weight Approvals Operating conditions multi camera management Firmware upgrades via FTP Built in web server for standard web browser access Pentium 4 CPU 1 0 GHz or higher or equivalent AMD 1GB RAM IPv4 ICMP RTSP RTP UDP IGMP RTCP SMTP SNTP
21. er of the CamView software key in the IP CAM ID and Password from the ID Password card And then double click this camera item You will then see the Camera video immediately No further NAT router setting modifications are needed 11 StarVedia Outdoor Day amp night IP Camera 001001012 001001011 001010232 E 001014187 001002130 001037125 001001012 001037106 001001011 001010232 001014187 00 Figure 2 6 Pop up play video password window 12 StarVedia Outdoor Day amp night IP Camera 3 Web configurations You login into the web configuration page by directly key in the IP address of the IP CAM or right click the searched IP GAM in the Auto Search list of the CamView software and click the Web Configure to open the login window of the IP CAM E gap 001 001010232 001014187 001002130 001005019 001006075 001029062 001004253 001034039 deer Dane sewer a Co Figure 3 2 IP Web configuration login page 13 StarVedia Outdoor Day amp night IP Camera 3 1 Information The first page of the web configuration of the IP CAM is the information page You can see the model name firmware version IP CAM ID registration status network type and current video settings bandwidth resolution in this page The IP CAM can be viewed remotely by the C
22. et you need to know the Internet speed bandwidth connected to your home network If the Internet speed setting of your IP camera is very large but your real Internet speed bandwidth is relatively low the video quality could be very bad In some worst case the video display could be disconnected In order to have the best video quality you better have broadband service from your ISP and set the Internet speed of the IP camera a little lower than the real Internet speed provided by your ISP Also need to notice that when multiple users are displaying the videos from the same camera at the same time the video bandwidth times number of users will be needed for the Internet speed 43 StarVedia Outdoor Day amp night IP Camera Appendix D Trouble shooting ol Could adjust the effective focus of the Cam A The effective focus of the IP Cam is from 30cm to infinity so in almost all DN gt circumstances you see the video clearly There is no need to adjust the effective focus What s the viewing angle of the IP Cam The viewing angle of the IP Cam is about 60 degrees What s the longest distance using the IP Cam to see the video When using the Cam to see a long distance object whether it s clear or not depends on the size of the object Usually when your eyes can see something clearly in that distance the IP Cam can also see that object clearly in about the same distance
23. et better video clearance The default value of this setting is high 10 Video color choose between colored and black amp white 11 Outdoor Indoor video for better video display quality modify this setting when taking indoor or outdoor video The default setting is Outdoor video in most cases this is also ok for indoor usage Under some special cases there could be some strip lines on the video display when the IP camera is taking indoor video In this situation change the setting to Indoor video will solve the problem Please also be noticed that in Indoor video setting the video display of outdoor view is 19 StarVedia Outdoor Day amp night IP Camera very vague For indoor usage if there is strong sun light into the room please select the Indoor sun light choice 12 Enable disable time display on video if enabled the date time of the system will be displayed on the left upper corner of the video When this modification is Save amp Apply ed it works immediately but all the connected video viewing users will be disconnected Seeing video from anywhere Outdoor IP Gamera IP CAM ID 001 001 014 Information Password play video Network Internet speed 512Kbps Video Adjust resolution amp frame rate automatically sa Use the following values Video Settings 2 Resolution JGPPIRTSP Night Mode Frame rate eye Favor Preference Image
24. hhmmss crf format where hh is the hour mm is the minute ss is the second of the starting time of the recording video The files are segmented every five minutes Users can use the free bundled CamPlay software to play back the video files Seeing the video from anywhere NAS Storage Settings Information Always Recording Schedule Recording C Disable Recording Network Keep recorded video for 3 days Circular recording Video C If free disk less inn GB Circular recording Stop recording k Email ftp Alarm Use NAS name nas storage DIDO Settings Use NAS IP address METRE Shared folder name test NAS access account test NAS access password test L J English Ed English EEEN Schedule Scheduling Admin Figure 3 13 NAS Storage Settings page 27 StarVedia Outdoor Day amp night IP Camera 3 10 Scheduling The IP Camera provides the scheduling function for the motion detection triggered email ftp sending and or the NAS recording with the individual parameters set in the Email ftp alarm settings and the NAS settings page Totally 12 schedule list items are allowed There is no conflict check for the scheduling it means that the scheduling time could be overlapped and the IP camera will do all the scheduled events during the overlapped time period For the scheduling of the Email ftp sending and or NAS recording the Schedule option must enabled in the
25. his upgrade A status message about the percentage done in the upgrade procedure is displayed Please be noticed that during the upgrade procedure do not power off the CAM otherwise the IP could probably enter into the safe mode section 3 14 After the upgrade procedure is finished the system will restart automatically You can upgrade from the ftp server or from the local file in your computer During this upgrade procedure do not try to modify other settings or view the video Seeing the video from anywhere Upgrade from FTP server Upgrade from local file Information Network FTP Server 60 250 194 78 Video Username upgrade Schedule Password Admin r Firmware filename IC602 gen 020201 n f Admin login l 2 Firmware location Led Control Date Time Upgrade reboot Language English Figure 3 17 Firmware upgrade settings page 32 StarVedia Outdoor Day amp night IP Camera Seeing the video from anywhere Fumware upgrade status Information Network Status erasing flash 12 Video Do not power off the device Schedule The device will restart after upgrade automatically Admin Admin login Led Control Date Time Upgrade reboot Language English v Figure 3 18 Firmware upgrade status page 33 StarVedia Outdoor Day amp night IP Camera 3 14 Reboot You can restart the manually on
26. ia Current Time 2009 04 21 15 21 56 System Up Time 0 days 0 hours 18 mins 48 secs Date Time Save amp Apply Upgrade reboot Language English Figure 3 15 System date time settings page 30 StarVedia Outdoor Day amp night IP Camera 3 12 Admin In this page you can modify the web login account With this account you can login to the IP CAM and do any modifications The default account is admin without password the login account is forgotten you can reset the to the factory default settings by following the steps in section 3 16 and login with the admin account Please be noticed that this account is different from the video play password in the Video settings page Seeing the video from anywhere Web Access amp Password Settings Web access port 80 Information La Network x Username admin gt Video Password Schedule Password confirm Save amp Apply Admin login Led Control Date Time Upgrade reboot Language English Figure 3 16 Admin settings page 31 StarVedia Outdoor Day amp night IP Camera 3 13 Upgrade If there is some new firmware available from the supplier of this IP CAM you can upgrade the firmware on this page Please ask for the correct information about FTP server username password account and firmware filename from your supplier and then do t
27. ify the password of the IP camera to prevent others to see the video For embedded web page integration add the following codes into the proper position of the desired web page object classid clsid 5C5 19EC4 2BAE 44CE B7F5 ADOCCD4BEFBD id mpeg4ax codebase http www starvedia com ActiveX axmpeg4 cab Version 0 0 0 0 width 320 height 240 gt param name Src value rtsp ip cam address CAM ID password mp2 lt object gt 46
28. ings like port mapping fixed IP DDNS virtual server of the NAT router StarVedia Outdoor Day amp night IP Camera devices it s just a plug amp play usage So the differences are the followings 9 9 9 Public address needed Dynamic DNS needed 2 Port mapping in router Virtual server in router 2 UPnP support in router What s needed No No No No No ID and Password StarVedia Outdoor Day amp night IP Camera 2 Hardware description and quick installation usage The IP CAM is designed to be very easy to install and use First let s see the major components of the IP CAM products 2 1 Major hardware components The major components of the products are listed below 1 Lens the focus of the lens is fixed you do not need to spend time to adjust the focus the effective focus range is from 30cm to infinity 2 IR LEDs there are totally 36 IR LEDs that can provide approximately 30m distance night vision 3 Light detector this light detector can detect when the light is becoming dark and turn on the IR LEDs automatically 4 Power jack this is the place to plug in the power adaptor The power needed for this IP CAM is 12V 1 0A please make sure you are using the correct power adaptor Ethernet jack this is the place to plug in the RJ45 Ethernet cable 6 Reset button this is the button to reset the IP CAM to default factory settings You need to press the reset but
29. mera in the NAS device or Stop recording as selected If the keep recorded video for xx days is selected the system will do circular recording and over write the recorded video files older than xx days ago 3 camera can connect to the NAS device by using the NAS or NAS IP address If the NAS device and the IP camera are in the same local area network the IP camera can automatically locate and connect to the NAS device by the NAS name If the NAS device uses a fixed IP address either in the local area network or in the public internet the IP camera can connect to it by the NAS IP address 4 The Shared folder name is the folder in the NAS device that will record the video files of the IP camera 5 The NAS access account and NAS access password are the username and password to login into the specified Shared folder name of the NAS device In the Microsoft Windows environment you can access to the NAS device by keying the URL address NAS name shared folder name or WNAS IP address shared folder name in the windows Internet Explorer and then key in the NAS access account and NAS access password to the prompted login window The video files are recorded under the subfolder IPCamRecordFiles Recording ID ID 26 StarVedia Outdoor Day amp night IP Camera where ID is the ID of this IP camera All the recorded files are with the name of
30. nual night mode control the IP Cam can be manually forced to night mode IR LEDs on or day mode IR LEDs off In order to get better video color display during day time and night time there is an ICR IR Cutter Remover in the IP Cam This ICR will be controlled automatically to filter out the IR Infrared light during the day time and allow the IR light to pass during the night time This make sure the video color quality is excellent compared to other IP camera Seeing the video from anywhere Night Mode Control Numbers of IR LEDs 12 Information Network Automatic day and night mode svatch Video Scheduled time of night mode Display During time Sis Video Settings Manual night mode control Night Mode Mode Schedule Current Status Day save amp Apply Admin Language English Figure 3 10 Night mode control page 22 StarVedia Outdoor Day amp night IP Camera 3 7 Email FTP Alarm The provides the Email ftp function you can enable or schedule the Email ftp ability in this page the IP CAM will then send out an email with a jpeg picture attached in the email and or send out the jpeg picture file to a ftp server The related settings are explained below 1 Email FTP trigger choose between motion schedule and disable A If motion is selected it means that when there is a motion detected the system will sen
31. of the specific IP camera detailed in section 3 6 Different 3G mobile phone may need different operation to be able to key in the rtsp address please contact the 3G mobile phone customer service for more details The video quality and resolution is the same value as set on the video settings page Since the bandwidth provided by the 3G service is under 256k bps better to configure the Internet speed of the IP camera to 128k or 64k bps For more information about operation on different 3G mobile phones please contact us for detailed document 45 StarVedia Outdoor Day amp night IP Camera Appendix F Third party and embedded web page integration For third party and embedded web page integration IP Cam support the standard RTSP protocol and video codecs needed by most generally used video play software including Apple QuickTime and VideoLAN The supported media protocols including and UDP IP Cam will automatically use or UDP media stream depends on the connection request The video codec supported is MPEG4 The access methods are the followings risp ip ID password mp2 for MPEG4 video MPEG2 audio rtsp ip address CAM ID password for MPEG4 video AMR NB audio Where ip cam address is the IP address of the IP camera CAM ID is the unique Camera ID of the specific IP camera Password is the video play password of the specific IP camera detailed in section 3 6 Users can mod
32. off during fumare EHE upzrade or caused by other abnormal operations E Information Tru This Camera is operating in safe mode only the functions working ji E Date Time You need to upgrade a new firmware now Admin Upgrade BE Reboot Figure 3 21 Safe mode information page 35 StarVedia Outdoor Day amp night IP Camera 3 16 Set to factory default For some reason for example you forgot the web login password you may want to set the IP CAM to the factory default settings The only thing you need to do is pressing the reset button on the cable for more than 4 seconds and release it do this when the IP CAM is powered on The IP CAM will reset to the factory default settings and restart automatically The web login account will be admin no password the play video password will be ipcam after reset to factory default Figure 3 22 Press the reset button to set to the factory default 36 StarVedia Outdoor Day amp night IP Camera 4 Features and specifications 4 1 Features gt gt gt VV VV ON ON ON ON WV Easily access the camera from anywhere in the world the ID password No complicated NAT router settings needed Free video management software CamView program accompanied for easy access and multi camera management 3GPP ISMA support Dual video streaming with separate frame rate resolution bandwidth settings for PC and mobile IR led cont
33. rol support automatic manual and scheduled modes But only can see black amp white video when IR led is on Built in Web server for managing via standard web browser Supports enhanced MPEG 4 compression Supports resolution of up to 640x480 pixels 30 frames per second View video from your Wireless or wired Ethernet network Supports PPPoE protocol for direct ADSL connection Motion Detection and E mail FTP notification attach jpeg image file Synchronize the time through NTP protocol Connect up to 20 users simultaneously please see appendix B Event scheduling NAS storage access Online Firmware upgrade will enter safe mode when power is off during critical firmware upgrade point Watchdog function to prevent system failure 37 StarVedia Outdoor Day amp night IP Camera 4 2 Specifications Models Power Processors Network interface Image sensor Light sensitivity Lens Water resistant IR LEDs Buttons Video compression Resolutions Frame rate Video streaming Image settings Security Installation management and maintenance Outdoor Day amp Night IP Camera DC 12V 1A RISC CPU hardware video processing and compression Ethernet 10BaseT 100BaseTX Auto MDIX RJ 45 RGB VGA 1 4 inch CMOS Automatic exposure control automatic white balance automatic gain control automatic brightness control 0 2 Lux IR led off 0 Lux with 30 meters IR leds on Automatically turn on the IR l
34. rver When this modification is Save amp Apply ed it works immediately but all the connected video viewing users will be disconnected The default setting is Disable Seeing the video from anywhere Email FTP Alarm Settings Information Email FTP Trigger Motion ODA Schedule Disable gt ce Motion sensitivity medium Video Send Email message Send FTP message NITE Email recipient test test com SMTP server test port 25 Email ftp Alarm NAS Settings Username test test com Scheduling SMTP Password eese i Admin FTP Server Username Language English v Password a Remote folder save amp Apply SMTP server test Figure 3 11 Email FTP Alarm page 24 StarVedia Outdoor Day amp night IP Camera 3 8 DI DO settings The IP camera provides DI alarm detection function The related settings are explained below 1 Digital input can select the normal status of the digital input as either open circuit or closed circuit The current status is also displayed An active status could trigger the email ftp or the NAS SD card recording by setting the scheduling Seeing the video from anywhere DI DO Settings Information os Open circuit Network Digital Input Normal Status A Current Status Actrve You Video Save amp Apply Schedule Email ftp Alarm DIDO Settings NAS Settings Scheduling
35. s possible that you can not view the IP CAM video through the firewall router In this situation please contact your MIS person to solve the problem _ Table 1 List of tested Wireless AP router devices CC Table A 2 List of tested Wired NAT router devices 41 StarVedia Outdoor Day amp night IP Camera Appendix B Maximum Allowed Video Users The maximum allowed video users for a single IP Cam at the same time is dependent on the video settings including Internet speed and resolution The followings are the summary of the maximum allowed video users Notice when the IP camera is doing NAS recording this is counted as one video user For video resolution of 160x120 pixels Frame rate bandwidth 64k 512k IM 1 5M For video resolution of 320x240 pixels Frame rate bandwidth 64k 256k 512k 768k IM 1 5M Sips 30 fps 20 18 9 For video resolution of 640x480 pixels Frame rate bandwidth 512k 768 1 5M 42 StarVedia Outdoor Day amp night IP Camera Appendix C Performance Information 1 Video Performance Information The video quality is dependent on the video parameter settings and the network quality If you want to have a better video quality you will usually set higher resolution and higher frame rate This is fine when you are viewing the video locally in the same network But when you want to see the video remotely through the Intern
36. ssage with the jpeg picture attached to the specified email account 4 Email recipient this is the email address to receive the detection notice message An email message with the jpeg picture file named by the date time of the triggered moment will reach this address 5 SMTP server this is the SMTP server that will help to transfer the email message This server is irrelevant to the Email recipient address 6 SMTP username password this is the account to use the SMTP server to transfer the email message The SMTP server and username password account are only for transfer the email message to the Email recipient the Email recipient could be on another email server or any reachable email address The 23 StarVedia Outdoor Day amp night IP Camera username and password fields could be left empty if no authentication is needed for the SMTP server 7 SMTP server test after the settings are filled you could press SMTP server test to check all the settings are correct 8 Send FTP message if this item is enabled the IP GAM will send out a jpeg picture file to the specified ftp account 9 FTP server this is the FTP server address to receive the jpeg file 10 FTP username password this is the username password to login into the FTP server so this triggered jpeg file will be allowed to reach this FTP server 11 Remote folder the jpeg file will be put under this folder of the FTP se
37. ssword card on the CamView and then you can see the video First Connect the IP CAM to the home office network Please connect the IP CAM accessaries to the IP CAM body correctly including the bracket power adapter and Ethernet cable as shown in Figure 2 2 And connect the other end of the Ethernet cable to the home network or office network Usually this Ethernet cable is plugged into a home NAT router device or an Ethernet switch if in the office as shown in Figure 2 2 Since the default settings of the IP CAM use DHCP function and very often there is DHCP server on most of the Home office network the IP CAM should be connected to the Internet immediately StarVedia Outdoor Day amp night IP Camera Power Adapter Figure 2 2 IP connection diagram Second Install the CamView software on the notebook PC Please insert the installation CD into the CD ROM drive in your notebook or personal computer must be running Microsoft Windows OS Execute the program CamViewlnstaller xxx exe on the disk The program will pop up some windows about the installation options please press the next button to proceed with the installation After the installation is complete there will be a CamView icon on the desktop of your computer screen please execute this icon The CamView program will run immediately IP CAMERA CamView Application User Manual Adobe Reader Figure 2 3 The installation CD disk Third Use
38. this page All the connected video viewing users will be disconnected Seeing the video from anywhere Information This will restart the device Network Schedule Admin Admin login Led Control Date Time Upgrade reboot Language English Figure 3 19 System reboot settings page Seeing the video from anywhere Information Rebooting Please wait Network Video Schedule Admin Admin login Led Control Date Time Upgrade reboot Language English Figure 3 20 System reboot under going page 34 StarVedia Outdoor Day amp night IP Camera 3 15 Safe Mode If by some abnormal operation for example powered off during the critical point of the upgrade procedure the IP CAM will enter into the safe mode In this mode you will see the following Safe mode page when login into this IP CAM Please do the upgrade operation immediately to recover the system On this safe mode the IP can not display the video on the CamView software but you can still find this IP CAM on the Auto search list The steps to recover from safe mode are the followings 1 Use CamView to locate the IP CAM by clicking the Auto Search item on the CamView software Login into the web configuration page of the IP CAM Upgrade the firmware from the Upgrade page seeing the video from anywhere Camera Safe mode The firnrware 15 damaged because of power
39. ton for more than 4 seconds to enable the reset function Usually when you forgot the administrator account you will probably need to do this reset action to reset to the default factory settings Please refer to section 3 16 for more details 7 Digital input terminal block this is for alarm detection an open circuit is off a close circuit is on 8 Status indication LED red this LED is to indicate the Internet connection status When the Internet connection is connected the LED will be constant red light If there is any Internet connection problem the LED will be blinking red light 9 Ethernet indication LED blue this LED is to indicate if the Ethernet link is ok and packet traffic is sending receiving When the Ethernet cable is connected the LED is constant blue light When there is packet sending receiving the LED is blinking blue light StarVedia Outdoor Day amp night IP Camera Ethernet Indiction LED Indiction LED Status Lens IR LED Light Sensor Ethernet Jack Microphone Jack Digital Input iT E ur S Terminal Block lt P Power Jack Reset Button Figure 2 1 Major components of the IP camera 2 2 Quick installation and usage There are only three things that you need to do to see the video from the IP CAM 1 Connect the IP CAM to the home office network 2 Install the CamView software on the notebook PC 3 Key in the ID password of the IP CAM from the ID Pa
40. ult setting is Enable 3GPP RTSP Seeing the video from anywhere 3GPP RTSP Settings Enable 3GPP RTSP Disable 3GPP RTSP Information Network 3GPP bandwidth B4Kbps Video Select resolution amp frame rate automatically Display Use the following values Video Settings 3GPP RTSP Resolution Frame rate Night Mode Access URL rtsp 10 10 10 173 001037091 4941 Notice usually public IP address is needed for 3G mobile access Admin Save amp Apply Language English Schedule Figure 3 9 3GPP RTSP enabled page 21 StarVedia Outdoor Day amp night IP Camera 3 6 Night mode control The IP Cam is able to work both in day time and night time There are some IR LEDs that can let the IP camera see the objects in the night time Users can adjust the numbers of the IR LEDs according to the view sight distance during night mode to get the best night mode vision The night mode status is also displayed This night mode control page is to control when the time the IR LEDs will be on There are three ways to control the night mode IR LEDs 1 Automatic day and night mode switch the IP will automatically turn on the IR LEDs when the night time is arrived or the environment is becoming dark There is a light sensor on the IP cam that is doing this light detection 2 Scheduled time of night mode the IP Cam can also be scheduled to turn on the IR LEDs in a time range of each day 3 Ma
Download Pdf Manuals
Related Search