KT-LCD5 eBike Display User Manual
Contents
1. 2 3 sical assist promotion function Aa MN D i Isl 524 Y Hold iv and A flashes the vehicle drives at the speed not more than 6Km h Release v button the function is invalid 2 4 THROTTLE display o 85 mms jf Turn on throttle THROTTLE display V 2 2 5 PAS Lpy IS ls 2 When Power assisted riding PAS display e J After the cruise function is turned on the trip riding speed is greater than 7 km h hold iv long and enter cruise the CRUISE lit Brake or hold any button to cancel 2 7 Display and delete of single Data N Nj After power on for 5 seconds hold a and iv at the same time a GU po m e eee mae D single trip riding time TM and single trip distance DST flash hold ESS ic E button shortly the content of both is cleared If failed holding the button WEZ OST S Tas within 5 seconds it will automatically return the display interface after 5 seconds original content is preserved 3 M 2 Hold D button shortly in display 1 to enter display 2 In the riding mnn ae Ls ee mode after 5 seconds display 2 automatically returns to display 1 4 Display 3 n P a888 N Hold LD button shortly in display 2 to enter display 3 In the riding O ne i Lol condition five seconds later a single maximum speed MXS display Cm automatically returns2. to the real riding speed Km H 5 In display 3 hold V button shortly SW and the display will re enter display 1 6 Hold V button to turn off the display and the power supply of controller 7 Automatically prompt interface Error Code Definition 01__info 7 1 Error Code Display Throttle Abnormality 03_info Motor hall signal Abnormality 04 info Torque sensor signal Abnormality 05__info Axis speed sensor Abnormality only applied to torque sensor 06 info Motor or controller has short circuit Abnormality Electronic control system failure will display flashing fault code Once the fault was removed it automatically exits from the fault code display interface General Project Setting 1 Set maximum riding speed After power on for 5 seconds hold a and iv at the same time maximum riding speed Km H and MXS flash hold or iv shortly to set g5 Dy the maximum riding speed default 25Km H Hold LD button shortly and go to the next parameter settings 2 Wheel diameter setting The wheel diameter will be set after finishing setting the maximum riding Hl fa a8 a rec LA speed wheel diameter specifications flashes Hold a or iv shortly to set the specifications of wheel diameter Select the range 6 8 10 12 14 16 18 20 22 2 888 as _ WI VY 24 26 700c and 28 inches Hold button shortly and go to the next parameter settings The metric units will be
3. KT LCD5 eBike Display User Manual V1 0 Dear customer please read this manual before you use KT LCD5 instrument The manual will guide you use the instrument correctly to achieve a variety of vehicle control and vehicle status display Functions and Display A 11 ami kaine speca tmperian O ws mme Pass eneee Ce ense cusefinion Om sieve eno Tomaia O mm Tawon vo ateryvotage s roms nose senor 15 O Tre ate aay w A oen push powerasst 14 D eackahe and esas Operation 1 ON OFF Hold LD button long to turn on the power and hold LD long for a second time to turn off the power When the motor stops driving and when the e bike is not used for a consecutive 5 minutes it will automatically shut down and turn off the motor power supply 2 Display 1 Hold L button to start up and enter display 1 2 1 Turn on backlight and headlights lAN ge Hold a long to turn on backlight and headlights the controller should ee have headlight drive output function hold a long again to turn off the UEL backlight and headlights 2 2 Assist ratio gear ASSIST switch LA wee E7 Hold A or shortly to switch 1 5 file gear Gear 1 is for the e minimum power gear 5 is for the highest power Each startup will automatically restore the gear shutdown last time the user can set randomly Gear O is Dy without booster function
4. set after finishing setting wheel diameter Km H and Km flash Hold Ba or iv shortly and select the three metric units of speed mileage and ambient temperature in synchronization 4 Km H and Km stop flash after metric unit setting is completed Hold LO button shortly again to re enter the maximum riding speed setting interface or hold LO button long to exit from setting environment of routine projects and save the setting values returning to display 1 5 Exit from routine project setting All three routine project settings can exit from the setting environment and return to the display if hold LO button long after each setting is completed meanwhile the setting values are saved Under each setting interface if the button failed holding for more than 1 minute it will automatically return to display 1 and the setting value is invalid Outline Drawings and Dimensions 1 Dimensions of main instrument body Side View Front View 2 Wiring diagram K Prepared by Suzhou Kunteng Electronics Co Ltd
Download Pdf Manuals
Related Search