OptoLyzer® MOCCA compact V3.1 User Manual - K2L
Contents
1. KZL CONNECTING NETWORKS OptoLyzer MOCCA compact V3 1 ISBN 978 1 62077 921 7 Copyright 2013 2014 K2L GmbH amp Co KG K2L All rights reserved Please make sure that all information within a document marked as Confidential or Restricted Access is handled solely in accordance with the agreement pursuant to which it is provided and is not reproduced or disclosed to others without the prior written consent of K2L The confidential ranking of a document can be found in the footer of every page This document supersedes and replaces all information previously supplied The technical information in this document loses its validity with the next edition Although the information is believed to be accurate no responsibility is assumed for inaccuracies Specifications and other documents mentioned in this document are subject to change without notice K2L reserves the right to make changes to this document and to the products at any time without notice Neither the provision of this information nor the sale of the described products conveys any licenses under any patent rights or other intellectual property rights of K2L or others The products may contain design defects or errors known as anomalies including but not necessarily limited to any which may be identified in this document which may cause the product to deviate from published descriptions Anomalies are described in errata sheets available upon request K2L products are no2. 240 kByte IN 32 96 kHz OUT 10 100 BASE TX RAM S PDIF 512 kByte USB 2 0 e 3 6 Pin FECA 12S MediaLB Figure 4 1 Block Diagram 4 3 Properties of Supported Bus Systems The OptoLyzer MOCCA compact is intended to be used as stimulation test and analysis device for automotive field buses with DUTs connected to them Therefore the design is constrained to ensure the behavior to be as passive as possible 4 3 1 CAN The accuracy of CAN time stamps is 500 us 4 3 1 1 High Speed Transceiver High speed CAN bus systems according to ISO 11898 2 2 are terminated with 120 Q at each end Therefore the OptoLyzer MOCCA compact does not terminate the bus The transmission speed ranges from 33 kbits s to 1 Mbits s 4 3 1 2 Low Speed Transceiver Low speed CAN bus systems usually have a distributed termination The value of the termination in each node depends on the number of nodes in the network To avoid effects on the total impedance of the network the OptoLyzer MOCCA compact has a weak termination of 5 6 KQ A communication via the low speed transceivers ranges up to a speed of 125 kbits s DS60001258B 12 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 4 3 1 3 Single Wire Transceiver The single wire CAN is terminated with 9 1 kQ The transmission speeds for single wire CAN are 33 kbits s on board communication and 83 kbits s off board communication
3. 3 a Each OptoLyzer MOCCA compact has either one MOST150 oPHY three MOST150 cPHY or one MOST50 ePHY connector DS60001258B 18 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual The OptoLyzer MOCCA compact offers up to seven LEDs All LEDs except the Power LED are tri colors Table 5 2 LEDs INTERFACE SYMBOL DESCRIPTION COLOR DESCRIPTION activity Blue Slowly Firmware running Twinkling Fast Flash mode Operation This LED indicates diferent Red Depending on firmware states dependent on the ATS etc state of the CAN bus MOST White Bus activity Twinkling FlexRay White Bus activity Twinkling This LED indicates a Green Powered device powered device White Bus activity Twinkling state of the MOST network variants that are supporting state of the FlexRay bus state of the LIN bus White Bus activity Twinkling a had K2L OptoLyzer MOCCA compact V3 1 19 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual 5 2 Rear Panel Different hardware variants and software configurations are available for the OptoLyzer MOCCA compact As a result some connectors might not be available for a specific variant of the OptoLyzer MOCCA compact mos cd Speed CAN LIN FlexRay Syne Power Figure 5 2 Rear Panel Variant with S PDIF Interfaces All components of the rear panel are described below Table 5 3 describes the connectors from top to
4. and MOST150 The delivery covers the following OptoLyzer MOCCA compact Power cable MOST cable optional USB cable USB stick license dongle CAN termination resistors optional Sync and power cable optional Adaptation Kit optional Check your shipment for completeness If you have any complaints direct them to sales K2L com Providing the delivery note number eases the handling DS60001258B 6 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 13 Definitions of Terms For better understanding of the following chapters this section provides explanation to special terms used in the description of the OptoLyzer MOCCA compact user manual Table 1 1 Definitions of Terms TERM ABBREVIATION DESCRIPTION Controller Area Network Coaxial electrical physical layer used e g in OptoLyzer MOCCA compact 150c variant EIN CO E CTN EI ECN Type of electrical connector used for transmitting audio and video signals also known as cinch introduced from Radio Corporation of America K2L OptoLyzer MOCCA compact V3 1 7 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual 14 References 1 Electrical Physical Layer Specification Version 2 0 Refer to FlexRay Consortium 2 International Organization for Standardization http www iso org 3 Telecommunications Industry Association http www tiaonline org 4 International Electrotechnical Commission
5. kHz USB Cypress EZ USB 2 0 The table below covers mechanical characteristics of the OptoLyzer MOCCA compact Table 7 2 Mechanical Characteristics PARAMETER VALUE UNIT Dimensions H x W x D EA Ambient Temperature Range 40 70 oc DS60001258B 30 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual The table below covers electrical characteristics of the OptoLyzer MOCCA compact Table 7 3 Electrical Characteristics Relay for external load potential free 12V DC shutter K2L OptoLyzer MOCCA compact V3 1 31 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 8 Maintenance Figure 8 1 shows how a cPHY connector of the OptoLyzer MOCCA compact 150c can be released or exchanged Figure 8 1 How To Release cPHY Connector Follow these steps 1 Depress the locking tab of the snap on coupling 2 Pull the jack away from the device while still pressing the locking tab DS60001258B 32 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 9 Revision History Table 9 1 Customer Revision History REVISION SECTION FIGURE LEVEL ENTRY CORRECTION DS60001258B Section 4 2 Block Figure 4 1 LIN Transceiver corrected SN65HVDA195 Diagram on page 12 DS60001258A All New OptoLyzer compact 150c variant DS number replaces version number ISBN number inserted cover page General improvement of wor
6. 0001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 3 Definitions Limit Class 3 1 Emission The OptoLyzer MOCCA compact has passed the requirements according to the standard EN 55022 2010 class A Warning The OptoLyzer MOCCA compact is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures DS60001258B 10 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 4 Introduction The OptoLyzer MOCCA compact is an out of the box automotive bus interface combining most of the current automotive field buses The device can be used e g as an automotive bus interface featuring simulation via PC or as an analyzing device for the different automotive bus systems Due to its PC compatible connections including USB 2 0 and 10 100 Mbit s Ethernet it is easily possible to control the embedded OptoLyzer MOCCA compact software from the PC including monitoring tracing and logging of data exchange over the different field bus systems The OptoLyzer MOCCA compact provides comfortable spy and stress functionalities for MOST The OptoLyzer MOCCA compact is available as different hardware variants optimized for dedicated use cases e g with or without MOST connector OPHY ePHY and cPHY variants different MOST speed grades 4 1 Feature Summary The following list covers the key featur
7. 4 3 2 FlexRay The termination of a FlexRay bus depends on the bus topology Two terminations are mandatory in each active branch The OptoLyzer MOCCA compact can be installed in various topologies Therefore a termination is not implemented in the device Thus the terminations have to be realized in a different way In addition the OptoLyzer MOCCA compact does not act as a bus guardian The OptoLyzer MOCCA compact provides one FlexRay interface and is able to switch from sleep mode to wake up mode stimulated by the FlexRay bus The bus is capable of transmitting up to 10 Mbit s brutto as per Electrical Physical Layer Specification Version 2 0 The accuracy of FlexRay time stamps is 500 us for the static part of the schedule 4 3 3 LIN Both LIN master and LIN slave functionality are supported The accuracy of LIN time stamps is 1 us The OptoLyzer MOCCA compact supports a maximum transmission speed of 20 kbit s brutto K2L OptoLyzer MOCCA compact V3 1 13 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual 4 3 4 MOST The OptoLyzer MOCCA compact variant supporting MOST50 is able to switch the clock mode of the embedded OS81082 INIC and thus supports a 44 1 kHz as well as a 48 kHz network whereas the OptoLyzer MOCCA compact variant designed for a MOST150 network has a fixed clock mode of 48 kHz OptoLyzer MOCCA compact variants of any speed grade have an INIC a SpyNIC for MOST and a StressNIC for MOST on board The StressN
8. 5 1 o steed beacuse anauseer ees heed ences een ee Pesos eunacedes cub eeu eeu et eau 16 5 2 A 20 Chapter 6 Pin Assignment of the Connectors 0 cece ccc e eee eee eees 22 6 1 High Speed CAN 234 2 42d44 6 cerda 8005 6504 a8 88 2 bedded a eee ee 22 6 2 IN PICKING 2 ota Gone oe a eon on ares Ge pee eeeuse Seach cues eoer een ees 23 6 3 LIN Low Speed CAN and Single Wire CAN 2 6 0 0 0 0 eee 24 6 4 Synchronization and Power 1 ee eee eee ee 24 6 5 Digital Audio In Out S PDIF 2 0 0 0 0 ee eee eens 25 6 6 Analog Audio NN OU 22sec ceetedecace wea ce pratense 25 6 7 USB secos asesoras E ea ee ee eee ae eee 25 6 8 Relay sores rags toser raro es dae torre esa ae da 26 6 9 A 26 610 MOST CONNGCIO e cemecarrorerirsa apre bros a rar rear ee ed Ges pa 27 6 10 1 MOST50 Electrical Connector a n aana aaa aaa eee 27 DS60001258B 2 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 6 10 2 MOST150 Optical Connector o oo ooooonon ees 27 6 10 3 MOST150 Coaxial Connector 20 00 00 ees 27 0 10 31 Simplex USE das idolo td 28 6 10 3 2 DUPlEX USO Cas associa ia esd eee ata 28 6 10 33 Duplex Endpoint Use CaS iia ide 29 Chapter 7 Technical Specifications oooooooooooooooooco oros 30 Chapter Via MtenanCe ss 4 ai SARA AR RANA ARA 32 Chapter 9 Revision History asii ta A 33 K2L OptoLyzer MOCCA compact V3 1 3 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compa
9. IC for MOST can be connected if desired via software The accuracy of INIC MOST time stamps is 500 us When analyzing data e g when interpreting an acknowledged code it is important to know how the chips INIC SpyNIC for MOST StressNIC for MOST are arranged inside the OptoLyzer MOCCA compact OptoLyzer MOCCA compact Figure 4 2 Order of Chips inside the OptoLyzer MOCCA compact The MOST feature is optional for OptoLyzer MOCCA compact variants e there are OptoLyzer MOCCA compact variants supporting MOST MOST50 or MOST150 or variants without MOST 4 3 4 1 MOST50 Data exchange between the OptoLyzer MOCCA compact and the embedded OS81082 INIC is realized by MediaLB 3 Pin with 512Fs 4 3 4 2 MOST150 Data exchange between the OptoLyzer MOCCA compact and the embedded OS81110 INIC is realized by MediaLB 6 Pin with 2048Fs 4 3 4 3 SpyNIC for MOST Each speed grade of an OptoLyzer MOCCA compact has also an appropriate SpyNIC for MOST on board Both speed grade variants of the SpyNIC are spying control packet and allocation messages A node is realized at the same time The accuracy of SpyNIC time stamps is 1 us 4 3 4 4 StressNIC for MOST Each speed grade of an OptoLyzer MOCCA compact has also an appropriate StressNIC for MOST on board Both speed grade variants of the StressNIC are supporting dedicated use cases for simulating some common network error situations e g light activity lock stress buffer full 1 An opt
10. Speed CAN 2 4 6 SIGNAL DESCRIPTION 3 se O ca INS ENT ICI IO ECN INICIO IE CECI 6 2 LIN FlexRay Connector type see Figure 6 1 DE 9 The provided GND pin must not be used unless there is no other GND connection This pin must not be used for supply purpose Table 6 3 Pin Assignment of Connector LIN FlexRay A B ICI O i ICE TC DION IESO O EI K2L OptoLyzer MOCCA compact V3 1 23 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual 6 3 LIN Low Speed CAN and Single Wire CAN 2 6 Connector type see Figure 6 1 DE 9 The provided GND pin must not be used unless there is no other GND connection This pin must not be used for supply purpose Table 6 4 Pin Assignment of Connector LIN Low Speed CAN IN ee INICIO IONES ETC 8 eaves Ga io wie 8 omen Ho CaN es ow os 6 4 Synchronization and Power There are two connectors for synchronization and power Figure 6 2 shows the pin assignment as it is visible on the rear panel for these connectors For more details about synchronization and power refer to Section 2 1 Supply and Synchronization on page 9 Figure 6 2 Pin Assignment of the Sync and Power Connector Table 6 5 Pinning of the Sync and Power Connector PNNO SIGNAL DESCRIPTION DS60001258B 24 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 6 5 Digital Audio In Out S PDIF Both digital connectors S PDIF In Out i
11. V3 1 33 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual Further Information For more information on K2L automotive products including integrated circuits software and MOST development tools and modules visit our web site http www K2L de Direct contact information is available at http www K2L de contact K2L GmbH amp Co KG Bannwaldallee 48 D 76185 Karlsruhe Germany Technical Support Contact information for technical support is available at http www K2L de contact DS60001258B 34 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL
12. bottom and left to right Table 5 3 Connectors on the Rear Panel INTERFACE DESCRIPTION High Speed CAN These two connectors offer six high speed CAN instances with baud rates from 40 kbit s 1 3 5 to 1 Mbit s depending on the cable length The CAN instances 1 3 4 and 5 are hard 2 4 6 specified as high speed CAN interfaces whereas the CAN instances 2 and 6 can also be used as low speed or as single wire CAN interfaces The CAN interfaces can be controlled by a customer application Details about the CAN bus properties are described in Section 4 3 1 CAN on page 12 For the pin out refer to Section 6 1 High Speed CAN on page 22 LIN FlexRay This DE 9 socket combines pins assigned to the FlexRay bus and pins assigned to the LIN channels 3 4 5 and 6 For the pin out refer to Section 6 2 LIN FlexRay on page 23 LIN Low Speed CAN This DE 9 socket combines two low speed and two single wire CAN interfaces CAN Single Wire CAN 2 6 instances 2 and 6 as well as two LIN channels 1 and 2 These CAN instances can be used either as high speed CAN interfaces or as low speed CAN interfaces or as single wire CAN interfaces These CAN interfaces can be controlled by a customer application For the pin out refer to Section 6 3 LIN Low Speed CAN and Single Wire CAN 2 6 on page 24 The Synchronization Sync and the Power connector have the identical pin assignment i e each socket can be used either for synchronization or power p
13. ct User Manual 6 10 MOST Connector 6 10 1 MOST50 Electrical Connector Connector type AMP 1376350 1 Figure 6 5 shows the pin assignment as it is visible on the front panel Figure 6 5 PIN Assignment of the MOST50 Connector Table 6 8 Pin Assignment of the MOST50 Connector PIN NUMBER DESCRIPTION 1 4 5 8 Not connected ETXN ERXN ERXP 6 10 2 MOST150 Optical Connector Connector type Tyco Micro FOT 2 0 The orientation of the Rx and Tx path is printed on the panel The MOST150 connector is designated for a 2 0 optical header cable The direction is visible on the cable a Tx Optical output for MOST network a Rx Optical input for MOST network 6 10 3 MOST150 Coaxial Connector Connector type 59S20X 40ML5 Z FAKRA Three different use cases are supported They are shown together with the appropriate connection diagrams in the following sections Each use case presents logically a ring even if the devices are physically connected by one cable e g duplex endpoint use case For more details about the coaxial interfaces refer to Table 5 1 on page 17 K2L OptoLyzer MOCCA compact V3 1 27 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual 6 10 3 1 Simplex Use Case Figure 6 6 Simplex Use Case In this use case the OptoLyzer MOCCA compact 150c observes and participates in a simplex ring Data is transmitted in one direction Thereby the single headed arrow shows the direction The OptoL
14. ct User Manual List of Figure 4 1 Figure 4 2 Figure 5 1 Figure 5 2 Figure 6 1 Figure 6 2 Figure 6 3 Figure 6 4 Figure 6 5 Figure 6 6 Figure 6 7 Figure 6 8 Figure 8 1 DS60001258B Figures Block DIAM sotossssrs tierra ron eee eee area a 12 Order of Chips inside the OptoLyzer MOCCA COMpaCt o ooooooocnonono nooo 14 Front Panel MOST150 oPHY and MOST150 cPHY Variant 16 Rear Panel Variant with S PDIF Interfaces o o o o ooooooonoana no 20 DESC OMOTO 2 rusticos ee us ao o ado da ao Uan 22 Pin Assignment of the Sync and Power Connector 00 0000 ee ees 24 Pin Assignment of the S PDIF Connector 0 00 00 ccc ees 25 Pin Assignment of the Analog Audio In Out Connector 0 00000 25 PIN Assignment of the MOST50 Connector anaana anaa aaae 27 SIMpIeX USC CASE oc ceccng ros dns rasa rs ada Aa 28 Duplex Use Case nanana Bed A A AR GAS ERS See hE HESS ee 28 Duplex Endpoint Use Case 20 cc ete ees 29 How To Release CPHY Connector 0 0 0 0c eee ees 32 4 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual List of Tables Table 1 1 Definitions of Terms eee ee ee eee T Table 5 1 Connectors on the Front Panel 0 0 0 0 ce ee eee eee 17 TavleO 2 CEP arpar erra N ia ese ee E ee R T 19 Table 5 3 Connectors on the Rear Panel 0 0 cc ee eee eee 20 Table 6 1 Pin Assignment of Connecto
15. depicts a variant supporting the MOST150 oPHY variant top and the MOST150 cPHY variant bottom gg Program Reset OptoLyzer MOCCA compact Program Reset MOST 150 OptoLyzer Figure 5 1 Front Panel MOST150 oPHY and MOST150 cPHY Variant All components of the front panel are described below a describes the connectors from left to right and top to down a describes the LEDs DS60001258B 16 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Table 5 1 Connectors on the Front Panel INTERFACE SYMBOL DESCRIPTION Analog Audio Out These interfaces are only available on variants that are supporting MOST The OptoLyzer MOCCA compact provides one stereo headphone output lt has a 3 5 mm jack plug Output Power Po max Rms 1 4 mW at R 16 Q Vout 150 MVRms ECL OptoLyzer MOCCA compact variants supporting MOST or Trigger m ECL can be used to wake up the OptoLyzer MOCCA compact according to different ECL implementations OptoLyzer MOCCA compact variants without MOST The trigger can be used to wake up the OptoLyzer MOCCA compact Both trigger variants are realized using a LIN transceiver For the pin out refer to Section 6 9 ECL on page 26 MOST These interfaces are only available on variants that are supporting ePHY variant MOST The MOST50 connector bases on an electrical physical layer ePHY whereas the MOST150 connectors base eit
16. ding Section 1 3 Definitions of New terms added cPHY ePHY and oPHY Terms on page 7 Section 2 3 Restrictions in New section Operation on page 9 Section 4 1 Feature MOST feature adapted new feature added support of Summary on page 11 simplex duplex and duplex endpoint use cases Section 4 2 Block cPHY added for MOST connector Diagram on page 12 Section 4 3 4 MOST on Description improved StressNIC for MOST can be connected page 14 optionally Figure 4 2 modified Section 4 3 4 1 MOST50 Currently 512Fs are used 1024Fs removed on page 14 Section 4 3 4 4 StressNIC Description improved light lock stress gt light activity lock for MOST on page 14 stress Section 4 3 5 Ethernet on Description improved relating to MAC address page 15 Section 4 3 6 Sleep Description improved hint added that software is needed to Mode on page 15 control sleep mode Section 5 1 Front Panel Figure 5 1 cPHY variant of MOST150 added on page 16 Table 5 1 new cPHY interfaces added Description of Program Reset button extended Table 5 2 power icon replaced by Pwr Section 6 10 3 MOST150 New section Coaxial Connector on page 27 Chapter 7 Technical Low Speed CAN Transceiver changed from NXP TJA 1054 to Specifications on page 30 NXP TJA 1055 Chapter 8 Maintenance New chapter on page 32 Rev 1 0 Initial Version 04 29 13 K2L OptoLyzer MOCCA compact
17. es of the hardware platform Some of the options may not be available in specific configurations 6 high speed CAN interfaces two of them selectable either as high or low speed transceiver or single wire CAN 1 FlexRay connector 6 LIN interfaces MOST150 cPHY or oPHY MOST50 ePHY or without MOST USB 2 0 port supporting high speed with 480 Mbit s and full speed with 12 Mbit s Ethernet connection with 10 100 Mbit s a S PDIF coaxial input and output for audio streaming over MOST Analog audio input and output for audio streaming over MOST a MOST ECL support or generic trigger in output Relay to switch external loads of up to 5A Time stamp synchronization with cascaded OptoLyzer MOCCA compact devices over power cables a SpyNIC for MOST on board a StressNIC for MOST on board a Simplex duplex and duplex endpoint use case support in CPHY variant of MOST150 K2L OptoLyzer MOCCA compact V3 1 11 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual 4 2 Block Diagram A block diagram shows the features available for the OptoLyzer MOCCA compact V3 1 In order to minimize crossing lines in Figure 4 1 below the FPGA was split into two blocks 4x CAN High Speed High Speed or 2x CAN Low Speed or 2 Single Wire CAN Flash j 2 MByte 16 V E 6x LIN 12 uC FPGA Renesas E Relay V850E2 FL4 H E A Bless a SA 2 Debug amp PC IN Flash RAM 2S OUT Analog
18. escribe which S PDIF formats are supported by the OptoLyzer MOCCA compact Direction S PDIF IN to MOST S PDIF data from an external S PDIF source routed to the MOST network The S PDIF IN is routed through a sample rate converter The signal can be either a mono or stereo signal os sine rro Direction MOST to S PDIF OUT S PDIF data from the MOST network routed to an external S PDIF sink The signal can be either a mono or stereo signal MOST Supported Framerates 8 bit channel 8 bit channel 16 bit channel 16 bit channel 32 96 kHz 24 bit channel 24 bit channel K2L OptoLyzer MOCCA compact V3 1 21 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 6 Pin Assignment of the Connectors 6 1 High Speed CAN Connector type for both High Speed CAN connectors DE 9 Figure 6 1 shows the connector pin assignment as it is visible on the rear panel Figure 6 1 DE 9 Connector The provided GND pins must not be used unless there is no other GND connection These pins must not be used for supply purpose Table 6 1 Pin Assignment of Connector High Speed CAN 1 3 5 ee i es es cmd O O to re OIC EE CN The provided GND pins must not be used unless there is no other GND connection These pins must not be used for supply purpose DS60001258B 22 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Table 6 2 Pin Assignment of Connector High
19. finitions of TONS one 2 oe dacenne dd aaa wemd eal tend aes Re SE ee deme eee oud T 1 4 ReferenceS eS 8 Chapter2 Safety Instructions c sar sanar 9 2 1 Supply and Synchronization a aaa eee eee 9 2 2 ROI veria ada Som carapace Hee om Seta ate a a ee ee ee ede eta ee A 9 2 3 Restrictions in Operation eee ee eens 9 Chapter 3 Definitions Limit Class 0 ccc ccc cc ccc cee oros 10 3 1 EMISSION espas Bs fo arica air EE de da Bod es R dD oes Se he A ea al SSeS Seer Gx eS 10 Chapter odu hOn so 40 ius cesascoreueuees ciao Gee eres eas bees eens 11 4 1 Feature SUMMAN conidios a aa 252 11 4 2 de IU En 12 4 3 Properties of Supported Bus Systems o eee eee 12 AO GAN seee i a e a pedira oe es cake es Oe a oe E e aa et 12 4 3 1 1 High Speed Transceiver occccocccocccccnoconoconoconccnononononononannnannonnnnnanonanonannnnnnonanananinaninns 12 4 3 1 2 Low Speed TranscCelVerT ooccoonccccncccncconoconcconnonononannnnnnonanonnnonnnnnnnonanonannnnnnenaninaninnnnnns 12 4 3 1 3 Single Wire Transceiver messi ateos dicas 13 4 3 2 FICKRAY si o ero a pe e aa a De re ax ee a oe ee O i ra 13 A RS uo 13 Om MOO raro rra ore raras arar a 14 EA A Pa 14 EA e 14 4 3439 SPYNIC TOP MOST cantara pri 14 4 3 4 4 StressNIC for MOS Escaso didas 14 4 00 meine pnsdstinas bons coe idad rado a a wee re 15 4 3 6 Sleep Mode 15 Chapter 5 Hardware DescriplOn s 40 6 04 40004446 6 iss wane eee wee ee aa 16
20. her on an optical OPHY variant physical layer oPHY or a coaxial electrical physical layer cPHY cPHY variant described separately below For the pin out refer to Section 6 10 MOST Connector on page 27 MOST The icon refers to the bottom part in Figure 5 1 This interface is only cPHY variant available on variants that are supporting the coaxial variant of MOST Rx connector The MOST150c connectors base on a coaxial electrical physical layer CPHY This connector provides an Rx interface It is used in simplex use cases as Rx indicated by the single headed arrow For more details refer to Section 6 10 MOST Connector on page 27 MOST The icon refers to the bottom part in Figure 5 1 This interface is only CPHY variant available on variants that are supporting the coaxial variant of MOST Rx Tx connector The MOST150c connectors base on a coaxial electrical physical layer cPHY This connector provides a duplex interface Rx Tx connection It is used in duplex use cases as Rx Tx indicated by the double headed arrow For more details refer to Section 6 10 MOST Connector on page 27 MOST The icon refers to the bottom part in Figure 5 1 This interface is only CPHY variant available on variants that are supporting the coaxial variant of MOST Tx and Rx Tx The MOST150c connectors base on a coaxial electrical physical layer connector CPHY This connector provides a Tx or a duplex interface Rx Tx connect
21. http www iec ch DS60001258B 8 K2L USER MANUAL K2L OptoLyzer MOCCA compact V3 1 OptoLyzer MOCCA compact User Manual Chapter 2 Safety Instructions 2 1 Supply and Synchronization The OptoLyzer MOCCA compact devices could be cascaded via Sync Power connector One of the two Sync Power connectors is intended to be used for the power supply and the other for cascading the OptoLyzer MOCCA compact by using an optional sync cable During cascading caution has to be taken since the first device in the chain can take the maximum current of 3 A Do not cascade more than eight devices in chain For all setups either a fuse of max 4 A in the supply cable to the first device or the use of the current limitation of the laboratory power supply is mandatory 2 2 Relay The Relay feature of the device is designed to switch other 12 V powered devices The capability is limited to 5A at 16 V maximum Always use core cable ends of appropriate length and diameter to prevent unintended connections 2 3 Restrictions in Operation The OptoLyzer MOCCA compact integrates temperature sensitive components Therefore do not cover the device with any objects Covering disables the passive cooling Make sure to allow enough airflow to the OptoLyzer MOCCA compact when the device is assembled Do never place the running OptoLyzer MOCCA compact in a closed case or box Do not stack any OptoLyzer MOCCA compact devices K2L OptoLyzer MOCCA compact V3 1 9 DS6
22. ical MOST2S5 interface is provided by the former hardware version MOCCA compact V2 3 2 Light relates to the OptoLyzer MOCCA 15300 variant activity relates to the OptoLyzer MOCCA 50e and OptoLyzer MOCCA 150c variants DS60001258B 14 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual simulation etc By default the StressNIC for MOST is electrically bypassed but can be enabled by appropriate software e g ATS see Figure 4 2 on page 14 4 35 Ethernet Auto MDIX is supported therefore the LAN interface can connect via straight and crossed patch cables The physical layer 100BASE TX is supported Thereby the MAC address of the Ethernet controller has a unique address The accuracy of Ethernet time stamps is 500 us 4 3 6 Sleep Mode The OptoLyzer MOCCA compact is able to scan the six CAN buses in sleep mode and if stimulated to switch from sleep mode into wake up mode In addition the OptoLyzer MOCCA compact can be waked up via FlexRay LIN or ECL For controlling the sleep mode software is needed to be developed by the customer K2L OptoLyzer MOCCA compact V3 1 15 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual a E gt E A e Fy YY ff ge he AYA A FA LAeCALIATAHKH st F A p ti L a gt Kh ya OW Ale JeQ cC Ci le 0 1 uy E EGSA AWW AE Ny OWI Tho UE 2 5 1 Front Panel Different hardware variants are available for the OptoLyzer MOCCA compact
23. ion It is used in simplex use cases as Tx indicated by the single headed arrow and in duplex use cases as Rx Tx indicated by the double headed arrow and in duplex endpoint use cases indicated by the double headed arrow For more details refer to Section 6 10 MOST Connector on page 27 K2L OptoLyzer MOCCA compact V3 1 17 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual Table 5 1 Connectors on the Front Panel INTERFACE SYMBOL DESCRIPTION Program Reset The device can be reset by the push button If the button is pressed for Program less than 1 s the device is reset The same button is used for switching Reset into the flashing mode if it is pressed for more than 2 seconds For details see the K2L Flasher Online Help that is part of the shipment Analog Line IN These interfaces are only available on variants that are supporting MOST The OptoLyzer MOCCA compact provides one analog audio Line IN The analog Line IN input impedance is 10 kQ The analog input is converted into a digital stream with resolutions of 8 16 or 24 bits channel both mono or stereo lt has a 3 5 mm jack plug The relay is able to switch 5 A as a potential free shutter For safety purposes refer to Chapter 2 Safety Instructions on page 9 For the pin out refer to Section 6 8 Relay on page 26 The USB port is a standard USB B type receptacle The LAN connector is an RJ45 receptacle according to TIA 568
24. nterface to a RCA phono socket Signal Figure 6 3 Pin Assignment of the S PDIF Connector The input circuit expects an unbalanced input and has an impedance of 75 Q The shield connects to system ground 6 6 Analog Audio In Out Both the stereo line in and the stereo headphone output interface to an audio phone connector Right Audio Signal y GND Left Audio Signal Figure 6 4 Pin Assignment of the Analog Audio In Out Connector 6 7 USB The USB port is a standard USB B type receptacle K2L OptoLyzer MOCCA compact V3 1 25 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual 6 8 Relay The relay is able to switch 5A as a potential free shutter Please refer also to Chapter 2 Safety Instructions on page 9 Relay type m assembled connector type RIA 31182102 connector type to be plugged RIA 31169102 The pin assignment below is described as it is visible on the front panel Table 6 6 Pin Assignment of the Relay Connector PIN NUMBER DESCRIPTION 1 left pin Shutter input 2 right pin Shutter output 6 9 ECL This connector provides two pins The upper pin is for connecting the ECL Trigger signal the lower pin for connecting GND Connector type a assembled connector type Molex 43045 0201 connector type to be plugged Molex 43025 0200 Table 6 7 Technical Values PARAMETER VALUE DS60001258B 26 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compa
25. r High Speed CAN 1 3 5 0 00 0000 cc eee 22 Table 6 2 Pin Assignment of Connector High Speed CAN 2 4 6 o ooooooooooooooo 23 Table 6 3 Pin Assignment of Connector LIN FlexRay A B 0 0 0 cc ee 23 Table 6 4 Pin Assignment of Connector LIN Low Speed CAN 0 0 0 cee eee 24 Table 6 5 Pinning of the Sync and Power Connector o o oo oooo ee ee ee 24 Table 6 6 Pin Assignment of the Relay Connector o o ooooooooo eee eee 26 Table 6 7 Technical Values ee ee eee eee eee 26 Table 6 8 Pin Assignment of the MOST50 Connector nananana naa aaa aa a eee 27 Table 7 1 Device and Bus Characteristics 0 0 0 0 0c ee eee eee 30 Table 7 2 Mechanical Characteristics naana aana aaa ee eee eee 30 Table 7 3 Electrical Characteristics 2 0 0 0 0 2 eee eee 31 Table 9 1 Customer Revision History o ooo 33 K2L OptoLyzer MOCCA compact V3 1 5 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 1 Preface 1 1 Intended Use The OptoLyzer MOCCA compact is intended to be used for developing testing or analyzing CANO FlexRay LIN or MOST based automotive products and systems by persons with experience in developing automotive devices 1 2 Scope of Delivery The OptoLyzer MOCCA compact is the hardware part of the following K2L products e g ATS OptoLyzer MOCCA compact Bundle including OptoLyzer Suite support for MOST50
26. t designed intended authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage Any and all such uses without prior written approval of an officer of K2L will be fully at your own risk The K2L logo is a trademark of K2L Other names mentioned may be trademarks of their respective holders K2L disclaims and excludes any and all warranties including without limitation any and all implied warranties of merchantability fitness for a particular purpose title and against infringement and the like and any and all warranties arising from any course of dealing or usage of trade In no event shall K2L be liable for any direct incidental indirect special punitive or consequential damages or for lost data profits savings or revenues of any kind regardless of the form of action whether based on contract tort negligence of K2L or others strict liability breach of warranty or otherwise whether or not any remedy of buyer is held to have failed of its essential purpose and whether or not K2L has been advised of the possibility of such damages K2L OptoLyzer MOCCA compact V3 1 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual Table of Contents Chapter ERCLACO es uranio ee ao aa 6 1 1 Intended Use ee eee ee eens 6 1 2 Scope of Delivery 20 4 2 548 cave oo Beh Sh ree oho a eee da a eee eae ed oo oe aoe 6 1 3 De
27. urposes Restrictions are described in Section Chapter 2 Safety Instructions on page 9 The OptoLyzer MOCCA compact is intended to be powered by the optional available wall power supply or by any other power supply which is capable to deliver 12 V and 1 A If the wall power supply is not used the included power cable has to be used to connect the 12 V supply to the OptoLyzer MOCCA compact For the pin out refer to Section 6 4 Synchronization and Power on page 24 DS60001258B 20 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Table 5 3 Connectors on the Rear Panel INTERFACE DESCRIPTION S PDIF These interfaces are only available on variants that are supporting MOST The output is IN compliant to the specification IEC 60958 4 with 75 Q and 0 5 Vpp 20 The output OUT is short circuit proof The input circuit expects an unbalanced input and has an impedance of 75 O Input sample rates from 32 to 96 kHz are accepted For the pin out refer to Section 6 5 Digital Audio In Out S PDIF on page 25 The OptoLyzer MOCCA compact offers the bidirectional transfer of audio streams between the MOST synchronous channel and the S PDIF connectors An audio stream on a MOST synchronous channel can be routed to the S PDIF output of the device It is also possible to route a digital audio stream from S PDIF input of the device to the MOST synchronous channel at the same time The following tables d
28. yzer MOCCA compact 150c can appear as an extra node in the ring 6 10 3 2 Duplex Use Case Figure 6 7 Duplex Use Case In this use case the OptoLyzer MOCCA compact 150c observes and participates in a duplex ring e g between a head unit and a camera Data is transmitted in both directions indicated by double headed arrows The OptoLyzer MOCCA compact 150c can appear as an extra node in the ring DS60001258B 28 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 6 10 3 3 Duplex Endpoint Use Case Figure 6 8 Duplex Endpoint Use Case In this use case the OptoLyzer MOCCA compact 150c observes and participates at one end in a duplex ring e g is acting either as a head unit or a camera Data is transmitted in both directions indicated by a double headed arrow The OptoLyzer MOCCA compact 150c can appear as an extra node in the ring K2L OptoLyzer MOCCA compact V3 1 29 DS60001258B K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 7 Technical Specifications The table below covers characteristics of the OptoLyzer MOCCA compact and its bus interfaces Table 7 1 Device and Bus Characteristics PARAMETER VALUE 512 kB external 240 kB internal Flash Memory 2 MB internal Controllers Controller Renesas V850E2 FL4 H 160 MHz CAN Transceivers Low Speed CAN Transceiver NXP TJA 1055 most cate o MOST Controllers S PDIF I O electrical via 2 x cinch input sample rate 32 96
Download Pdf Manuals
Related Search