Home

Document

1. Please seek assistance from qualified technician or local retailer for replacement 2 Improper tire pressure will result in hazards Over the standard pressure can cause a flat tire Lower than the standard pressure can cause tire relaxation or even dropping and resulting in losing control of the vehicle 3 When the tire tread wearing is over 2mm please replace new tire in time Please seek assistance from qualified technician or local retailer for replacement Tire gauge optional Manufacturer wiil provide to customers to measure tie pressure Tire gauge is put on the key ring ofthie key switch for users convenience Measure method Unscrew valve cap then press it toward the valve cap with tire gauge The measured value is tie pressure Put back the valve cap and crewat after measuring Operating Inspection before riding Idling inspection 1 Stabilize the vehicle shake it up and down to inspect the swing arm and fork condition to make sure it move normally and without interference 2 Check whether the front and rear the shock absorber is deformed or leakage or not 3 Check whether the front suspension and the rear flat fork is fastened in place 4 Hold the vehicle when checking 5 Repair and replace parts in time when finding that negative phenomena 6 Contact with the dealer when the situation is out of control Front brake inspection Check whether the front brake installation is firm the braking effect is valid 1 Fro
2. OPERATION MODE FRONT REAR TIRE SPECIFICATIO N HYDRAULIC SPRING ABSORBER F BY HAND R BY HAND F 16x8 7 R 16x8 7 EXHAUST SILENCE TYPE STARTING MODE IGNITION MODE DRIVE MODE IMPEDANCE COMPLEX EXHAUST MUFFLER ELECTRIC START CHIAN DRIVE FRONT REAR TIRE PRESSURE FRONT REAR TIRE RIM TYPE F 165kpa R 165kpa F STEEL WHEEL R STEEL WHEEL SOBRICATION MODE COOLING MODE PRESSURE amp SPLASH LUBRICATION AIR COOLED HEADLIGHT PECIFICATION PRIMARY REDUCTION RATIO FINAL REDUCTION RATIO NEAR LIGHT 12V 15 15W DISTANCE LIGHT 12V 15 15W 3 720 4 058 FUEL BRAND MIXTURE RATIO OF FUEL OIL amp LUBRICANT OIL LWA dB A DRIVE RATIO VIBRATION m s
3. CIRCLE AND ROTATE REDUCTION PE DIAMETER SPEED r min RATIO DRIVE RATIO Headlight VIBRATION m s 10 72 CE plate 1 0 N La men m n7 Ge y p7wj Functional switc 47 o n PRODUCT KXD ATV 003 NAME MODEL LENGTH X 1500x905x97 ENGINE i39FPMB 147FMD 147FMF 152FMH 154FMI WIDTH X15 MODEL HEIGHT mm AXLE BASE BORExSTROKE 39x41 4 4741 4 47x49 5 52 4x49 54x54 mm S 5 WHEEL BASE CYLINDER 72 86 107 124 mm WORKING VOLUME ml MIN GROUND COMPRESSION 8 8 1 8 5 1 9 1 1 9 5 1 CLEARANCE RATE mm TURNING UNLOADING 1500 100 CIRCLE AND ROTATE DIAMETER SPEED r min mm DRY WEIGHT RATED POWER 2 2 7500 3 7 7000 4 0 8500 4 7 8500 5 8 7500 kg Kw r min 100 100 100 100 100 THE WEIGHT MAXIMUM 2 5 3000 4 5 6000 5 6 6000 6 5 6000 7 0 5500 OF FULL TORQUE 100 100 100 100 100 FURNISHMEN N m r min T Kg RATED LOAD CARBURETOR PLUNGER TYPE QUALITY kg TYPE MAXIMUM CLUTH TYPE AUTO MULTI DISC WET CLUTCH SPEED Km h OIL SPARK PLUG A7TC CAPACITY TYPE L FRONT REAR HYDRAULIC EXHAUST IMPEDANCE COMPLEX EXHAUST MUFFLER SHOCK SPRING SILENCE TYPE ABSORBER ABSORBER TYPE FRONT REAR STARTING ELECTRIC START BRAKE MODE OPERATE TYPE FRONT REAR F BY HAND IGNITION C D I BRAKE R BY HAND MODE OPERATION MODE FRONT REAR F 16x8 7 DRIVE M
4. 7 MODEL LENGTH 1325x800x ENGINE MODElz Medus 147FMD 147FMF 152FMH 154FMI WIDTH 930 HEIGHT mm 840 CE plate AXLE BASE BORExSTROKES 39x41 4 47x41 4 47x49 5 52 4x49 54x54 mm 5 WHEEL BASE 580 CYLINDER 49 72 86 107 124 mm WORKING VOLUME ml 8 5 1 1 MIN GROUND COMPRESSION 8 8 1 8 8 1 CLEARANCE RATE mm TURNING UNLOADING AND 1500 100 CIRCLE ROTATE SPEED DIAMETER r min DRY WEIGHT RATED POWER 2 2 7500 3 7 7000 4 0 850 4 7 850 5 8 7500 kg Kw r min 100 100 0 100 0 100 100 THE WEIGHT MAXIMUM 2 5 3000 4 5 6000 5 6 600 6 5 600 7 0 5500 OF TORQUE 100 100 0 100 0 100 100 FURNISHMENT N m r min Kg RATED LOAD CARBURETOR PLUNGER TYPE QUALITY kg TYPE MAXIMUM CLUTH TYPE AUTO MULTI DISC WET CLUTCH SPEED Km h OIL TANK CAPACITY L 3 4 SPARK PLUG A7TC TYPE FRONT REAR SHOCK ABSORBER TYPE FRONT REAR BRAKE OPERATE TYPE FRONT REAR BRAKE OPERATION MODE FRONT REAR TIRE SPECIFICATIO N HYDRAULI EXHAUST C SPRING SILENCE TYPE ABSORBE R IMPEDANCE COMPLEX EXHAUST MUFFLER STARTING MODE ELECTRIC START IGNITION MODE C D I F 16x8 7 DRIVE MODE CHIAN DRIVE R 16x8 7 FRONT REAR TIRE PRESSURE FRONT REAR TIRE KIM TYPE HEADLIGHT PECIFICATION F 165kpa LUBRICATION PRESSURE amp SPLASH LUBRICATION R 165kpa MODE F STEEL COOLING MODE AIR COOLED WHEEL R STE
5. E CYLINDER 49 R2 86 107 124 TYPE R STEEL mm WORKING WHEEL VOLUME ml HEADLIGHT 12V 18W FUEL BRAND 2904 MIN GROUND COMPRESSIO 8 8 1 8 8 1 8 5 1 9 1 1 9 5 1 PECIFICATIO CLEARANCE N RATE N mm PRIMARY 3 720 4 058 MIXTURE TURNING UNLOADING 1500 100 REDUCTION RATIO OF CIRCLE AND ROTATE RATIO FUEL OIL DIAMETER SPEED r min amp LUBRICANT mm OIL DRY WEIGHT RATED 22 7500 3 7 7000 4 0 8500 4 7 8500 1 5 8 750 FINAL kg POWER 100 100 100 00 04100 REDUCTION PA QB 78 Kw r min RATIO THE WEIGHT 90 MAXIMUM 2 5 3000 4 5 6000 5 6 6000 6 5 6000 1 7 0 550 DRIVE RATIO VIBRATION m OF FULL TORQUE 100 100 100 00 04100 s D FURNISHMEN N m r min T Kg RATED LOAD CARBURETOR PLUNGER TYPE QUALITY kg TYPE SPEED Km h tontbrak OIL TANK 3 4 SPARK PLUG A7TC CAPACITY TYPE L FRONT REAR HYDRAULIC EXHAUST IMPEDANCE COMPLEX EXHAUST MUFFLER SHOCK SPRING SILENCE TYPE ABSORBER ABSORBER TYPE FRONT REAR F DRUM STARTING ELECTRIC START Rear wheel BRAKE R DISC MODE OPERATE TYPE FRONT REAR F BY HAND IGNITION MODE C D I BRAKE R BY HAND i o OPERATION MODE FRONT REAR F 16x8 7 DRIVE MODE CHIAN DRIVE epu SPECIFICATIO PRODUCT PRODUCT KXD ATV 005 N ATV NAME MODEL FRONT REAR F 165kpa LUBRICATION PRESSURE amp SPLASH LUBRICATION LENGTH X 1450x970x91 ENGINE MODEL 139FMB 147FMD 147FM 152FMH 154FMI TIR
6. E R 165kpa MODE WIDTH X 10 F PRESSURE HEIGHT mm FRONT REAR F STEEL COOLING MODE AIR COOLED AXLE BASE 970 BORExSTROKE 394444 47x41 4 47x49 52 4x49 54x54 TIRE RIM WHEEL mm S 5 5 TYPE R STEEL WHEEL BASE 700 CYLINDER 49 72 86 107 124 WHEEL mm WORKING HEADLIGHT 12V 18W FUEL BRAND 2904 N VOLUME ml PECIFICATION MIN GROUND 220 COMPRESSION 8 8 1 8 8 1 8 5 1 9 1 1 9 5 1 PRIMARY 3 720 4 058 MIXTURE RATIO CLEARANCE RATE REDUCTION OF FUEL OIL mm RATIO amp LUBRICANT TURNING 3600 UNLOADING 1500 100 OIL CIRCLE AND ROTATE FINAL 2 64 DIAMETER SPEED r min REDUCTION EE 78 mm RATIO DRY WEIGHT RATED POWER 2 2 7500 3 7 7000 4 0 850 4 7 8500 5 8 750 DRIVE RATIO VIBRATION m s kg Kw r min 100 100 0 100 100 0 100 E nU THE WEIGHT MAXIMUM 2 5 3000 4 5 6000 5 6 600 6 5 6000 7 0 550 OF FULL TORQUE 100 100 0 100 100 0 100 FURNISHMEN N m r min T Kg RATED LOAD 90 CARBURETOR PLUNGER TYPE QUALITY kg TYPE MAXIMUM 70 CLUTH TYPE AUTO MULTI DISC WET CLUTCH Headlight Bumper R cE pie Functional switch m PRODUCT KXD ATV006 NAME MODEL LENGTH X 1450x785x90 ENGINE MODEL 139FMB 447FM 147FM 152FM 154FMI WIDTH xlo D F H HEIGHT mm AXLE BASE 870 BORExSTROKE 30 41 4 47x41 4 47x49 524x4 54x54 mm S 5 9 5 WHEEL BASE 575 CYLINDER 49 2 86 107 124 mm WORKING VOLUME ml MIN GROUND 160 COMPRESS
7. EL WHEEL NEAR FUEL BRAND LIGHT 12V 15 15W DISTANCE LIGHT 12V 15 15W PRIMARY REDUCTION RATIO FINAL REDUCTION RATIO DRIVE RATIO 10 72 VIBRATION m s 1 0 3 720 4 05 MIXTURE RATIO 8 OF FUEL OIL amp LUBRICANT OIL LWA dB A SS Front brake Dipped headlight High beam LWE g Uu L Functional switc Bumper m PRODUCT KXD ATV 008 NAME MODEL LENGTH X 1500x980x980 ENGINE MODEL 139FMB 147FMD 147FMF 152FMH 154FMI WIDTH X SH m AXLE BASE 955 BORExSTROKES 29x41 4 47x41 4 47x49 5 52 4x49 54x54 mm 5 WHEEL BASE 700 CYLINDER 49 72 86 107 124 mm WORKING VOLUME ml 1 1 MIN GROUND CLEARANCE mm COMPRESSION RATE 9 9 TURNING CIRCLE DIAMETER mm DRY WEIGHT kg UNLOADING AND ROTATE SPEED r min RATED POWER Kw r min 1500 100 2 2 7500 3 7 7000 100 100 4 0 8500 100 4 7 8500 5 8 750 100 0 100 THE WEIGHT OF FULL FURNISHMENT Kg RATED LOAD QUALITY kg MAXIMUM TORQUE N m r min CARBURETOR TYPE 2 5 3000 4 5 6000 100 100 PLUNGER TYPE 5 6 6000 100 6 5 6000 7 0 550 100 0 100 MAXIMUM CLUTH TYPE AUTO MULTI DISC WET CLUTCH SPEED Km h OIL TANK CAPACITY L 3 4 SPARK TYPE PLUG ATTC FRONT REAR SHOCK ABSORBER TXPE FRONT REAR BRAKE OPERATE TYPE FRONT REAR BRAKE
8. ION 8 8 1 8 8 1 851 911 95 1 CLEARANCE RATE mm TURNING 3160 UNLOADING 1500 100 CIRCLE AND ROTATE DIAMETER mm DRY WEIGHT 80 SPEED r min RATED POWER 2 2 7500 3 7 700 4 7 850 5 8 7500 kg Kw r min 100 0 100 0 100 100 THE WEIGHT 82 5 MAXIMUM 2 5 3000 4 5 600 6 5 600 7 0 5500 OF FULL TORQUE 100 0 100 0 100 100 FURNISHMENT N m r min Kg RATED LOAD 90 CARBURETOR PLUNGER TYPE MAXIMUM 70 SPEED Km h CLUTH TYPE AUTO MULTI DISC WET CLUTCH OIL SPARK PLUG A7TC CAPACITY L TYPE FRONT REAR HYDRAULIC EXHAUST IMPEDANCE COMPLEX EXHAUST SHOCK SPRING SILENCE TYPE MUFFLER ABSORBER TYPE FRONT REAR BRAKE OPERATE TYPE FRONT REAR BRAKE OPERATION MODE ABSORBER STARTING MODE ELECTRIC START F BY HAND R BY HAND IGNITION MODE CD FRONT REAR F 16x8 7 DRIVE MODE CHIAN DRIVE TIRE R 16x8 7 SPECIFICATIO N FRONT REAR F 165kpa LUBRICATION PRESSURE amp SPLASH LUBRICATION TIRE R 165kpa MODE PRESSURE FRONT REAR F STEEL TIRE RIM TYPE WHEEL R STEEL COOLING MODE A R COOLED WHEEL HEADLIGHT 12V 18W FUEL BRAND 290 PECIFICATION PRIMARY REDUCTION RATIO 3 720 4 058 MIXTURE RATIO OF FUEL OIL amp LUBRICANT FINAL REDUCTION OIL 2 64 LWA dB A 78 RATIO DRIVE RATIO 10 72 VIBRATION m s 1 0 A di Headlight y Rear wheel J PRODUCT KXD ATV 00
9. ODE CHIAN DRIVE TIRE R 16x8 7 SPECIFICATIO N FRONT REAR F 165kpa LUBRICATION PRESSURE 8 SPLASH LUBRICATION TIRE R 165kpa MODE PRESSURE FRONT REAR F STEEL COOLING TIRE RIM WHEEL MODE AIR COOLED TYPE R STEEL WHEEL HEADLIGHT 12V 18W FUEL BRAND 290 Zeene n PRIMARY 3 720 4 058 MIXTURE REDUCTION RATIO OF FUEL RATIO OIL amp LUBRICANT OIL FINAL 2 64 LWA dB A REDUCTION 78 RATIO DRIVE RATIO VIBRATION m s 10 72 1 0 2 MAXIMUM 70 CLUTH TYPE AUTO MULTI DISC WET CLUTCH SPEED Km h OIL TANK 3 SPARK PLUG A7TC CAPACITY TYPE L Functional Switc h FRONT REAR HYDRAULIC EXHAUST IMPEDANCE COMPLEX EXHAUST MUFFLER SHOCK SPRING SILENCE ABSORBER ABSORBER TYPE TYPE FRONT REAR STARTING ELECTRIC START BRAKE MODE OPERATE TYPE Headlight a d V f FRONT REAR F BY HAND IGNITION C D I BRAKE R BY HAND MODE OPERATION MODE FRONT REAR F 16x8 7 ORIVE MODE CHIAN DRIVE TIRE R 16x8 7 PRODUCT PRODUCT KXD ATV 004 SPECIFICATI NAME MODEL ON LENGTH X 1450x920x91 ENGINE i39FMB 447FMD 447FMF 152FMH 154FMI FRONT REAR F 165kpa LUBRICATICN PRESSURE amp SPLASH LUBRICATION WIDTH X10 MODEL TIRE R 165kpa MODE HEIGHT mm PRESSURE AXLE BASE BORExSTROK 39x44 47x41 4 47x49 5 52 4x49 5 54x54 FRONT REAR F STEEL COOLING AIR COOLED mm ES TIRE RIM WHEEL MODE WHEEL BAS
10. Original instructions Please read this owner s manual carefully before using this product This is most important Please read this owner s manual carefully Its good for drivers safety and vehicle s maintenance If the rider is without safety awareness or driving experiences please do drive under the adult s supervision This is most important It s very important for your safety This product is recommended for riders of 16 years old or over Do not lend the vehicle to others who don t know how to operate Please observe the local law and regulations Content Safety warning Compliance with the law Assembling The position of the VIN Key switch Function switch Charger Emergency turn off stop switch Burglar Alarm Tire and Tire pressure gauges Operating Inspection before riding Idling inspection Front rear suspension inspection Front brake system inspection Rear brake system inspection Battery inspection Tool bag inspection Self Protection inspection Starting Training Riding Parking Cleaning Storage Transport Delivery Maintenance amp accessories Accessory description data circuit diagram age warning and warning labels OWNERS MANUAL Manufacturer Zhejiang Kingroma Industrial amp Trading CO LTD Address NO 1 Baihe Road Baihuashan Industrial Area Wuyi Zhejiang China Please note that this is a general manual So the style of the ATV that you ha
11. UE 100 0 100 100 100 0 100 REDUCTION FURNISHMENT N m r min RATIO Kg DRIVE RATIO VIBRATION m RATED LOAD 90 CARBURETOR PLUNGER TYPE Is l QUALITY kg TYPE MAXIMUM CLUTH TYPE AUTO MULTI DISC WET CLUTCH SPEED Km h LWA dB A Functional swite OIL TANK 3 SPARK PLUG A7TC CAPACITY L TYPE FRONT REAR HYDRAULIC EXHAUST IMPEDANCE COMPLEX EXHAUST MUFFLER SHOCK SPRING SILENCE TYPE ABSORBER ABSORBER TYPE FRONT REAR F DRUM STARTING ELECTRIC START BRAKE R DISC MODE OPERATE TYPE FRONT REAR F BY HAND IGNITIONMODE C D I BRAKE R BY HAND OPERATION MODE FRONT REAR F 16x8 7 DRIVE MODE CHAN TIRE R 16x8 7 SPECIFICATIO N FRONT REAR F 165kpa LUBRICATION PRESSURE 8 SPLASH LUBRICATION PRODUCT ATV PRODUCT KXD ATV 002 TIRE R 165kpa MODE NAME MODEL PRESSURE LENGTH X 1390x760x91 ENGINE MODEL 139FMB 147FMD 147FMF 152FMH 154FMI FRONT REAR E STEEL COOLING AIR COOLED WIDTH X O TIRE RIM TYPE WHEEL MODE HEIGHT mm R STEEL AXLE BASE 830 BORExSTROKE 39x41 4 47x41 4 47x49 5 52 4x49 54x54 WHEEL mm S 5 HEADLIGHT 12V 18W FUEL BRAND 2902 WHEEL BASE 555 CYLINDER 49 72 86 107 124 PECIFICATION mm WORKING PRIMARY 3 720 4 058 MIXTURE VOLUME ml REDUCTION RATIO OF FUEL MIN GROUND 200 COMPRESSION 8 8 1 8 8 1 8 5 1 9 1 1 9 5 1 RATIO OIL CLEARANCE RATE amp LUBRICANT mm OIL TURNING 2440 UNLOADING 1500 100 FINAL
12. down or side lay it 3 Ensure the vehicle is well fixed on the trailer or forklift 4 Handling with care Maintenance Unprofessional person may not understand the large information of this part So Training will not explain in details For more details please contact local retailer Necessary maintenance is the important guarantee to keep the vehicle in good condition Please maintain the vehicle according to time list Engine maintenance After every driving please ciose the switch of carburetor and oil way Release the rest oil This is very important If not do t accordingly the vehicle will not be easily started after it has been placed for a long time or carburetor will leak Maintenance time list Please do operate strictly according to maintenance list I Inspection Maintenance or lubricant replacement C Cleaning L Add lubricant Fuel System Throttle spark plug carburetor IKC Brake pads brake system Nuts and bolts Tire suspension system Battery if available The position of spare parts parameter Electrical diagram age warning and other warning labels and plats e OFF ROAD USE ONLY Improper ATV use can result in SEVERE INJURY or DEATH Sek ALWAYS USE HEVER U88 Pre NEVE USE AN APPROVED CM PUBLIC WITH DRUG HELMET ARD ROADS OR AL TORA OTECTINVE Improper tire pressure or overloading can cause loss of control Loss of control can resul
13. e steady runs 3 At the beginning turn the throttle slowly Training Unprofessional person may not understand the large information of this part So Training will not explain in details Advice Learn from local professional institution or the retailer Operating and driving way in the first or second weeks may affect the vehicle future performance Please pay more attention During this period do not turn the throttle into maximum should alter the speed often After training period maintain the vehicle according to maintenance form strictly Keep the vehicle in good condition Training is necessary Improper operation will result in the vehicle and result in serious injuries and death If the driver is without the safety awareness or driving experiences please drive it under the supervision of the adults Riding Before driving please review thie safety driving way and its importance 1 Pay attention to the brakes workirg condition always 2 Driving with only one hand is dangerous and forbidden 3 Turn the throttle slowly Never turn it Suddenly 4 Release the throttle and use the brake te niake it slow down 5 Make sure both the front brake and the rear 5rake work at the same time when braking Never force too hard that will reduce the working life of the brakes 6 Do not make dangerous movement while driving te_erisure safety Parking 1 Turn back the throttle and brake at the same time 2 Turn the key t
14. hen unscrew or screw nuts to be best condition Finally make the nuts of chain adjuster screwed Fungu is lero f aS 4 a 2 0 T d E P a d i lt 1 em kr am e x ME No fixing mit ax ze Be j em f k At e JAN vi en 1 _ r N na d IN SAA _ py i A e DH al sagt ing mut The position of the VIN The VIN is on the right side of the front frame VIN number Key switch Key switch is on the right side of the vehicle ront part indicating OFF and NO OFF condition Key can be taken out Light can not be turned on if light available engine can not be started ON condition Key can not be taken out When engine is being started headlight can be turned on if headlight available Function Switch Functional switch is in left side of handlebar which consists of horn start headlight flame out function 1 Electric horn button Po When key switch is on press it tnan it rings 2 Start horn button Red EX press it to start the vehicle when brake hand is ready 3 Headlight suton BD near light distance light 4 Turn off witen LI turn um on Charger optional 1 The input voltage is 220V or 110V the same as voltage in local place and output voltage is12V 2 When the vehicle is charging the indicator light turns to be red When the vehicle is fully charged the indicator light turns to be green Burglar alarm
15. n mE T Kg TL RATED LOAD CARBURETO PLUNGER TYPE mu zm asa QUALITY kg R TYPE MAXIMUM CLUTH TYPE AUTO MULTI DISC WET CLUTCH S OIL TANK 3 SPARK PLUG A7TC Rear brake CAPACITY L TYRE FRONT REAR HYDRAULI EXHAUST IMPEDANCE COMPLEX EXHAUST MUFFLER SHOCK C SPRING SILENCE Ze ABSORBER ABSORBER TYPE FRONT REAR F DRUM STARTING ELEGTRIC START BRAKE R DISC MODE OPERATE TYPE FRONT REAR F BY HAND IGNITION C D I BRAKE R BY HAND MODE OPERATION MODE FRONT REAR F 16x8 7 DRIVE MODE CHIAN DRIVE Front suspension SPECIFICATIO Engine N PRODUCT ATY PRODUCT KXD ATV 001 FRONT REAR F 165kpa LUBRICATIO PRESSURE amp SPLASH LUBRICATION NAME MODEL TIRE R 165kpa N MODE LENGTH 1230x745x8 ENGINE 139FMB 147FMD 147FMF 152FMH 154FMI PRESSURE WIDTH X 30 MODEL FRONT REAR F STEEL COOLING HEIGHT mm TIRE RIM TYPE WHEEL MODE AIR COOLED AXLE BASE BORExSTRO 39x41 4 47x41 4 47x49 5 52 4x49 5 54x54 R STEEL mm KES WHEEL WHEEL BASE CYLINDER 49 72 86 124 HEADLIGHT 12V 18W FUEL BRAND 290 mm WORKING PECIFICATION VOLUME ml PRIMARY 3 720 4 058 MIXTURE REDUCTION RATIO OF mm RATIO FUEL OIL DRY WEIGHT RATED POWER 2 2 7500 3 7 700 4 0 8500 4 7 8500 5 8 750 amp LUBRICANT kg Kw r min 100 0 100 100 100 0 100 OIL THE WEIGHT l MAXIMUM 2 5 3000 4 5 600 5 6 6000 6 5 6000 7 0 550 FINAL OF FULL TORQ
16. nt brake handle is mounted on the right side 2 The brake is working well if backward movement of the brake handle is in the top 20 30mm 3 Check if the tire rotation is good after releasing the brake lever 4 Contact the dealer for the need of brake maintenance 5 The front brake lever is with parking feature as well Use it when parking Rear brake inspection Check whether the rear brake installation is firm the braking effect is valid 1 The rear brake is mounted on the left hand or on the right foot 2 The brake is working well if backward movement of the brake handle is in the top 20 30mm or downward movement of the top of the foot brake lever 20 30mm 3 Put the brake lever or foot brake lever back into place quickly and check if the tire rotation is good when the force is removed 4 Contact the dealer for the need of brake maintenance 5 Inspect the brake shoe regularly and replace if timely when it is worn out as the brake shoe is a worn pieces of block 6 Do not open the brake casually as the brake fluid will damage people s skin Clean the skin with water of go to the doctor when it happens 7 The rear brake lever is with parking feature as well Use it when parking Battery check if available The battery of this vehicle is maintenance free 1 Check whether battery joint is tight If there is some part broken please change it 2 Do not throw off the battery which resulting in environment pollution 3 Do n
17. o OFF position when the vehicle stops then take out the key 3 Parking function is recommended at this moment to avoid sliding Cleaning After every riding the driver should clean the vehicle Then place it on flat ground to clean and then check 1 High pressure air or water will harm the vehicle 2 Do not splash water on these parts key switch cables and battery 3 Generally to wash the vehicle with clean water 4 Do not turn on the key switch immediately after cleaning 5 Chain should be daubed with lubricating grease Storage The quality will be influenced if you do not use vehicle for a long time Before storage vehicle must be checked to ensure it is in a good condition 1 Check the weight of vehicle from the parameter list 2 Clean up the vehicle and then wax its surface 3 Turn off the key switch 4 Clean the chain and then lubricate it 5 Lubricate all the cable parts 6 Place the vehicle well packed in a cool ventilated place to avoid damp and sun exposure Transport This is a process of transport the well packed vehicle 1 Check the weight of vehicle from the parameter list 2 Ensure the package well protects the vehicle 3 Ensure the vehicle is well fixed on the trailer or forklift 4 Handling with care Delivery This is the process of delivery the well packed vehicle 1 Check the weight of vehicle from the parameter list 2 Ensure the vehicle is placed normally Do not turn it upside
18. o receive training from importer or etaier and learn the operation skills 19 Learn local laws and regulations of ATV driving from ihexetailers 20 It s easy to be burned by break after using the vehicle fora long time 21 Although the vehicle is with safety designed measures harms siill can not be avoided ce JO 01 PS 0 M gt Please read the warning labels on the vehicle carefully and understand them fully 1 Warning caution label includes important safety information 2 User must understand the content of labels completely and carry out 3 Make sure all the labels are put on the vehicles already 4 When finding the labels are not clear or fall off please ask dealers for them to stick on the vehicles to ensure the integrity of all the labels Compliance with the laws and directives 2006 42 EC MACHINERY DIRECTIVE 2004 108 EC EMC DIRECTIVE 97 68 EC ENGINE POLLUTANT DIRECTIVE Assembling guide 1 Place packing box on the flat ground then open it with the scissors or cutter 2 Use 10 open end wrench and 6 allen wrench to apart the packing metal 15t step Please install steering linkages tighten nut with 25N m force and adjust the balance of the left and the right 200 step Please install rear shock absorbers and tighten nuts on both sides with 25N m force 3 step Please install the front tires make the tread pattern and cycle valve outside and tighten nuts with force between 35N m 45N m 4
19. optional 1 The input voltage is 12V Anti theft function Press the lock key vehicle is in alerting condition 2 Keyless function Don t need to turn on the key switch Press the start button twice continuously and then operate the vehicle 3 Telecontrol stop function With the keyless function used first press the button of unlock within the certain distance of remote control the power of vehicle will be turn off Please note This function is ineffective if vehicle is to be turned by key switch the tute IT the Emergency turn off stop switch It s put in the left side of the rear frame or on the left handlebar Pull or press down the switch the engine will be stopped The emergency rope can be fastened on the driver When there is emergency the vehicle will be stopped automatically by the driver getting off the seats and pulling down the rope Tire and Tire gauge Tire The proper tire pressure can provide the maximum stability and comfortableness Do check and adjust the tire pressure regularly to make sure the pressure to be on the standard grade To find the tire size and standard pressure please check parameter list and warning label on the vehicle To find the Load bearing and speed grade please check the tire surface 1 Check tire pressure and condition before driving Please make the replacement if there is any following condition happened broken stabbing or rim is out of shape
20. ot charge the battery until it is out of power 4 When the vehicle placed for extended period of inactivity check the electric quantity every 3 weeks Charge it when below 12V 5 When charging using or placing the battery do not put it upside down Tool bag inspection Check whether tool bag is take revery time before riding The tool bag is equipped with some refessional tools You can use time when in need Self protection inspection Self protection inspection is the guarantee of nleased driving and life safety Please wear the protective clothing correctly to ensure your safety Protective clothing consists of these parts below fe VE k ay Every check and inspection step above is necessary there is danger existing when driving Please conform the above process before driving and operate in accordance with the standard strictly when driving will protect your and life safety The warning sticker put on the surface of vehicle includes important safety information User must comprehend fully and act strictly It will cause the extreme injure and even death if not carefully checking or executing Starting Following the steps below to start the engine 1 Park the vehicle on the flat ground 2 Turn on the key switch to NO position Make sure it s well connected 3 If the engine doesn t start please open the choke valve first Try again Close the choke valve when the engin
21. step Please install the rear tires make the tread pattern and cycle valve outside and tighten nuts with force between 50N m 60N m gth step Please install handlebar adjust to proper angles and tighten nuts with force between 15N m 25N m e step Please install bumper and accessories and tighten nuts with force between 15N m 25N m Connect battery cables When you connect battery cables electric lock is in the sate of OFF Positive first then negative Disassembly is opposite If you fail to understand the instruction please contact with the local retailers and get professional confirmation after installation Loading Adjustment This step should be checked regularly to ensure safety and convenience Check the toe in of front tire make suie the front center distance is 5 10mm shorter than the rear center distance overhead view of front tires rear center distance the center line of vehicle left ugi right tire front center distancd Make sure the connection is ON and no part is OFF So vehicle can be started at anytime Adjust the Chain Use the index finger to press lightly the middle position between power output sprocket and rear sprocket The best condition should be pressed 15mm to 20mm If it is not in this range please adjust the chain adjuster Please note The chain adjuster should be adjusted at the same time to ensure the balance of both side To loosen the fasten nuts of chain adjuster first and t
22. t in severa injury or death PR GEAR Haag esos ces pons e Mover permit Se cae age t operate t ATV Cold tire pressure e ea Ye adversely affect vehicle handling Front 7 0 5 psi 4843 5 kPa ripe dete aano DA Rear 7 0 5 psi 4843 5 kPa OFF ROAD use ordy e Maximum weight capacity 200 bs 80kg Operation on public streets roads of highways ha Megal Always wear a helmet and other protective equipment Do net operate this vehicle after consuming Alco hol K Dr Satin t ftammabis shut oti engine avold sparks and open flame when refusing Read owners mantal care amp iby before riding NWARNING Please use 290 leadless gasoline Stop the engine when filling gasoline avoid the fire and explode CIRCUIT DIAGRAM MIN GROUND 115 COMPRESSI 8 8 1 8 8 1 8 5 1 9 1 1 9 5 1 yellow biack CLEARANCE ON RATE Due mm headiemp switch headamp TURNING UNLOADING 1500 100 I T ee B 1 CIRCLE AND ROTATE RS red DIAMETER SPEED r min mm e b AS yel DRY WEIGHT RATED 2 2 7500 3 7 7000 4 0 8500 4 7 8500 5 8 7500 DN blue white MI Lwhil ctifios kg POWER 100 100 100 100 100 E st E Kw r min Vas a THE WEIGHT MAXIMUM 2 5 3000 4 5 6000 5 6 6000 6 5 6000 7 0 5500 1 1 de M e spark 3 OF FULL TORQUE 100 100 100 100 100 g SS x 8 FURNISHMENT N m r mi
23. ve may differ from the picture shown in this manual Safety warning This vehicle is not a toy Rider under16 years old must use this product under adult s supervision Children must be trained before driving This is very important Be sure of children s ability to forbid the risk This is very important Children must understand the manual and the importance of warnings on the manual User must read the owner manual carefully and understand the content of the manual Incorrect operation of this ATV will result serious injury or even death Age limit warning See aluminum warning plate on the ATV 9 This product is not intended for OFF ROAD use Please get off the vehicle and walk with it when crossing the roads 10 Never ride with more than one person 11 Never attempt to operate this vehicle while under the influence of alcohol or drugs avoid injury or death 12 Please control the speed do not drive at excessive speed 13 The vehicle is not allowed to use in the adjustment or maintenance period 14 Be sure the vehicle is in a good condition before using it 15 Do not modify the vehicles or change the spare parts This is unsafe and illegal 16 The accelerating installation of the vehicle has been set Users should not adjust it which may result in serious injuries and death 17 Before riding please wear the safety helmet g oves protection dress and footwear Jo ensure the safety 18 It is necessary t

Document

Contents

Download Pdf Manuals

Related Search

Related Contents