ASC1 Owners Manual
Contents
1. to confirm that you wish to delete all satellites and positioning data SAT Data Reset Prompt will display Select Reset Soft Limit and press OK Press OK a second time within 3 seconds to confirm that you wish to delete the East and West software limits Soft Limit Reset Prompt will display Select Reset Position and press OK Press OK a second time within 3 seconds to confirm that you wish to reset the Positioner Count to 0000 SAT Position Reset Prompt will display Select Global Reset and press OK Press OK a second time within 3 seconds to confirm that you wish to reset all data and return to the default settings Please note that this will delete all satellite positions satellite names polarity and skew settings All Data Cleared Prompt will display Resynchronize All Satellite Positions If the motor or actuator position is moved or count is changed it may be necessary to correct all satellite positions simultaneously The satellite receiver s DiSEqC 1 2 Installation menu will support this function ASC1 lt Feature Pending gt 11 Back Light Timeout l Select Back Light Set Press OK Select the length of time the backlight will be lighted and press OK An arrow will appear to the right of the selected time setting Select Save Press OK Select Quit and press OK to return to the main menu satellite List and Polarity Programming If a DiSEqC 1 2 enable receiver will be used to progr2. actuator motor power connections using 12 14AWG wires These wires are typically red and black color 5 Verify that the M1 M2 S1 S2 wires are correctly connected to both the ASCI and the motor Failure to correctly connect these wires or short will damage equipment and void warranty 6 Connect the AC cord from the ASCI to the wall outlet Do not remove or defeat the ground blade on the IEC AC cord This ground connection protects you and your equipment 8 Turn Master Power Switch ON The Main Menu will appear for 20 seconds If the Main Menu disappears and the Default Operation Display appears press the Return button to display the Main Menu Setting Software East West Limits The mechanical limiters inside of the actuator motor should have already been set to prevent extreme dish movements that could damage the reflector or motor If the mechanical limits have not been set this should be done before setting the ASCI software limits Software limits should only be an additional precaution to prevent hardware damage l Select Soft Limit Set and press OK The Position counter should display 0000 The dish should already be parked near the West Mechanical limit setting Select Set as WEST Limit and press OK EAST Limit Saved prompt will be displayed Select Position and press the East Key to drive the motor to the Eastern limit If the dish starts moving in the wrong direction the M1 M2 wires must be swapped be sure
3. line return and each column is separated by a comma e Column 1 is the Satellite Name of up to 14 alpha numeric characters e Column 2 is positive or negative 4 digit number indicating the counter position of up to 10 000 counts 5000 0000 5000 This count is specific to your system and location e Column 3 is positive 2 digit number for vertical polarity degree offset range 0 to 90 with default vertical setting of 45 degrees e Column 4 is negative 2 digit number for horizontal polarity degree offset with default horizontal setting of 45 degrees 16 Operation Satellite Receiver Control The ASCI may be automatically controlled by a connected Satellite receiver using DiSEqC 1 2 commands Please refer to the receiver s owners manual on how to program and use a motorized dish using DiSEgC 1 2 All motor positioner installation and operation can be completed using the STB s Installation menu Polarity offset installation adjustment is not native to most DVBS or S2 satellite receivers and this will be set using either the ASC1 front panel buttons or with the ASCI remote If you are a beginner to using DiSEqC 1 2 motor control we suggest that you initially program the receiver and ASC1 using the receiver s installation menu This will assign the same DiSEqC 1 2 motor Position number to both the receiver and the ASC1 A quick overview of receiver motor control The STB stores a 2 digit motor position number for each satellite motor p
4. Port Loader Editor 13 Operation Control with a Satellite Receiver 16 Stand Alone Controller 17 Important Notice Save all original boxes manuals accessories and packaging materials in case it 1s necessary to return the merchandise Before unpacking or assembly of any item inventory the accessories and check for damage Review the warranty exchange and refund policies provided by your reseller Immediately contact your reseller to report any issues Package Contents e ASC1 Controller e 2 AAA Batteries e Remote Control Unit e RS 232 F F DB 9 Cable e UL approved 3 pin AC cord Materials contained in this installation manual are the property of Titanium Satellite PO Box 1201 Meadow Vista CA 95722 530 652 4405 http www TitaniumSatellite com Important Safety Instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Q Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or thir
5. S Precautions TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE CAUTION A A THE COVER OR BACK NO USER SERVICEABLE PARTS ARE INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL A This symbol indicates dangerous This symbol indicates important voltage inside the product that instructions accompanying the presents a risk of electric shock or product personal injury Do not install this equipment in a confined space such as a bookcase or similar unit WARNING To prevent damage which may result in fire or electric shock hazard do not expose this appliance to rain or moisture D The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus The mains plug is used as the disconnect device The disconnect device shall remain readily operable NEC ANSI NFPA 70 _ ANTENNA LEAD IN WIRE _ ANTENNA T DISCHARGE UNIT NEC SECTION 810 20 ELECTRIC y SERVICE 3 J f EQUIPMENT TUO gt lt GROUNDING CONDUCTORS MI b d NEC SECTION 810 21 MIU sd a Z GROUND CLAMPS POWER SERVICE GROUNDING L T ELECTRODE SYSTEM NEC ART 250 PART H Example of Antenna Grounding Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthor
6. Tiranium Satellite ASC1 Satellite Positioner and Polarity Controller Owners Manual v Tiranium Satellite Congratulations You now own the most advanced satellite dish controller based on the latest technologies the ASC1 dish actuator and polarity controller by Titanium Satellite The ASCI has been assembled using the highest quality components to provide exceptional performance and years of reliable operation The ASCI maybe used as a stand alone or as a fully automatic positioner when connected to your DISEqC capable satellite receiver Replaces old legacy analog or 4DTV satellite receivers to completely control a motorized satellite dish No more conversion charts taped to the wall or juggling multiple remotes to position the dish and select the correct polarity Any DiSEqC capable satellite receiver connected to the ASCI using a single coax cable automatically controls satellite dish positioning polarity and skew offset Simply change channels on your STB and the ASC1 will take care of the rest Unattended blind scanning of the entire arc with both polarities on a mechanical polarity servo type system is once again possible PC loader editor software and a RS 232 serial port allows back up and restoration of satellite positions custom satellite names and even share your custom satellite list No more hours of reprogramming after factory reset No need to send the ASC1 in for reprogramming or put up with outdated satelli
7. am and control the ASC1 connect the STB to the REC port and use the receiver s Satellite Installation menu and DiSEqC 1 2 sub menu to program the satellite motor positions then skip to steps 25 28 Please note that your receiver may have preassigned DiSEqC 1 2 positions or limit the number of programmable DiSEqC 1 2 motor positions Contact your receiver reseller for any questions on the operation and programming of these DiSEqC 1 2 settings Manual ASC1 Programming 4 5 Select Satellite Set and press OK Select DiSEqC 1 2 motor position number example 00 and press OK A black color block will flash over this two digit number Use either the numeric remote control keys to enter a two digit number 01 99 for example 01 or use the front panel Up Down keys to select the motor position number Press OK to exit the DiSEqC setting line Select Position Use the East West keys to drive the motor to the first satellite The motor count increases or decreases as the motor positions the dish W lt or gt E symbols indicate West or East direction o travel Bump the Dish East and West one count at a time to be sure that the signal is optimized on your signal quality meter or attached STB meter Place an attached signal meter or STB on both horizontal and vertical transponders to be sure that the feedhorn is properly positioned If using a polarity servo it is suggested to align the feedhorn with the ASCI default polarity settings of Horizon
8. atic Control w DiSEqC 1 2 11 LNB LNBF Connection F type 13 18 18 13 18 13Vdc or Off 12 Serial Com RS 232 Upgrade Edit Back up and Computer Control Installation It is recommended that you only use high quality coax cable that is RG6 or better with compression fittings and water proofed connections for all distribution Motor power wires M1 M2 should be at least 12 14AWG The sensor and servo wires should be 18 22AWG with a shield to minimize position count motor setting and polarization control errors Carefully verify all connections prior to turning on the ASCI Master Power Switch Incorrect connections will damage the equipment and void warranties This manual assumes that the satellite dish has been prepared for the ASC1 installation with the motor East and West mechanical limiters set and the dish parked in a position that is a few degrees East of the West mechanical limit Actuator Motor Feedhorn Sensor Actuator Motor Connection l Verify that the ASC1 Master Power Switch is OFF Select the Correct AC Line voltage for your install location Use the 115 setting for AC voltages 90 130Vac and 230 setting for AC voltages 200 240Vac 3 Connect the ASCI S1 S2 terminals to the actuator motor position sensor connections using 18 22AWG wires It does not matter which wire is connected to either S1 or S2 These sensor wires are typically brown color TOP L S AOASTABLE 4 Connect the ASCI MI M2 terminals to the
9. crolling Green Color Backlight 7 Keys Power OK Lock Keyboard Remote Dual Menu Nav East West Skew Skew 19 Active Keys Power OK East West Skew Skew Previous Home Numeric 0 9 11Lx9 5Dx4 5 Hin 280 L x 240 D x 115 Hmm 11 7 Ibs 5 3 KG Front Panel Keys Remote Control Keys DiSEqC is a trademark of EUTELSAT Assembled in China Warranty This product is warrantied against manufacturing and design defect for one year from the date of purchase All warranty claims must be processed through your reseller and include a copy of the purchase receipt This warranty is available only to the Customer whose name appears on the sales invoice If a Vendor warranty is stated on the invoice Vendor will repair or replace at Vendor s option the product containing manufacturing defects as long as the product is returned in its original shipping materials to Vendor within the original Vendor warranty period Firmware upgrades with unapproved files or hardware modifications by a non Vendor approved technician voids any and all warranties expressed or implied No merchandise will be accepted for repair or replacement without prior RMA number ASC1 Front Panel Keys l Standby Operate Mode 2 Drive Motor East Menu Function Left 3 Polarity Skew Offset Increase Menu Function Up 4 Drive Motor West Menu Function Right 5 Menu Function Enter or Accept 6 Po
10. d prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer B Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over B Unplug this apparatus during lightning storms or when unused for long periods of time D Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Caution These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualifie to do so WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE AND OBJECTS FILLED WITH LIQUIDS SUCH AS VASES SHOULD NOT BE PLACED ON THIS APPARATU
11. e 14 Firmware Upgrade l 2 Download and unzip the latest ASCI firmware file We recommend that the current Satellite list be downloaded saved before upgrading the firmware If the firmware overwrites the Satellite List or you perform a Factory Reset the saved Satellite List may be quickly loaded back to the ASC1 and your custom settings re installed Select the Update Tab Click Start and set the ASC1 firmware file path The file information will propagate the Product Model Date and Version information fields Click Start A status bar will display the transfer progress Caution It is not recommended to interrupt the update while in progress This could corrupt and disable the ASC1 It is best practice to allow an incomplete upgrade attempt to time out after 2 minutes Always close the ASC1 Loader Editor Software and power cycle the ASC1 using the rear master power switch before initiating another upgrade attempt When the Upgrade is complete 100 a window will indicate Update Process Completed Click Yes to exit the Upgrade It is good practice to power cycle the ASC1 using the master power switch on the rear of the unit Upload Satellite List to the ASCI l UN o talis y Dunne o Danaum corda DEL KSCID AOKCI Fee lain iden i ai Fien m as Select the Satellite Setting Tab secu Click Read From File pos Set the file path to the saved Satellite List file Click Ope
12. e receiver or the ASCI 16 ASCI Control The ASCI may be used as a stand alone dish actuator motor and polarity controller Once the satellites are programmed following the Manual Programming instructions on page 12 the controller may be operated from the operation screen or the Satellite Setting Screen 1 To move to a different satellite select the DiSEqC 1 2 position example 01 139W AMCS Press OK 2 Ifusing the remote control use the numeric key to enter the two digit motor assignment number If using the front panel press the up down keys to select the desired satellite 3 Press OK and the ASCI will move the dish to the selected satellite and set the skew offset 4 To fine tune the dish position press East or West on the remote control or front panel 5 To fine tune the skew offset select the correct polarity and press the or on the remote control or front panel 6 To save the new settings select Save and press OK Press OK again within 3 seconds to confirm that you wish to save the new settings NOTE This is an evolving document Please check back regularly for new firmware versions and supporting manual updates describing the new features and functions Please email your product requests and suggestions to support titaniumsatellite com Titanium Satellite 2013 17
13. ized substitutions may result in fire electric shock or other hazards Modification to the hardware or software without authorization by the manufacturer the will result in voiding any warranty Service assistance may be arranged by contacting your reseller Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition ASCI Specifications AC Voltage In 115 230Vac 50 60hz User Setting 600 1200mA 115Vac 340 640mA 230Vac Current in Standby 270mA 115Vac 120mA 220Vac Input Protection 2A 250Vac User Replaceable Fuse Output Voltage M1 M2 38Vdc max Output Current M1 M2 5A max Dual Motor Relays 10Amp 40Vdc max IF In Out Connectors F type IEC169 24 Female Loop Through Output Voltage F Fitting 13Vdc 18Vdc Automatic or Fixed Output Current F Fitting 450mA max Over Current F Fitting Thermal Protection w Auto Reset Current in Operation Motor Connections M M Screw Terminal 14 gauge S S Screw Terminal 14 gauge Gnd Pulse 5Vdc 550m Screw Terminal 14 gauge RF Insertion Loss 2 5dB DiSEqC Control Amplitude 0 8 0 2V required input level DiSEqC 1 2 Positions 99 Positioner Count 10 000 5000 to 5000 Sensor Resolution 50hz 90 from Polarity Setting Transfer Rate 56Kbps 9 pin Male D Sub LCD Operation Programming 4 Line S
14. larity Skew Offset Decrease Menu Function Down 7 Lock Keypad and Remote Remote Control Keys 0 00 0000c Standby Operate Mode Numerical Keys Satellite Selection d e dag Menu Navigation Up Down F F P a s f a A E ES 1 ae a f s Enter or Accept Drive Motor West or East Polarity Skew Offset 90 Return to Previous Go To Operation Screen Rear Panel 1 T e CAUTION pde l Q i3 i 38Vdc 5A Max Actuator Motor MEE LL E PS POP OF Osos pb o k m LE HAT fe 12 11 10 5 6 789 Critical Setting To prevent damage and voiding the ASC1 warranty before connecting the power cord to the ASCI or powering on the input voltage selector switch must be set for the local AC power voltage For regions with electrical voltage of 90 130Vac select the 115 position For regions with voltages between 200 240Vac select 230 AC Input Voltage Select 115Vac 230Vac AC Input Power Cord Connection IEC C14 type AC Fuse 250Vac 2A 5 x 20mm slow blow type approved Master Power Switch Motor Connection M1 M2 swap wires if reverse motor movement Positioner Count Sensor S1 S2 must connect to prevent move error Polarity Servo Ground typical color code black Polarity Servo Pulse or Skew typical color code white pe 2 xp v e de i e Polarity Servo 5Vdc typical color code red 10 Receiver Connection F type Autom
15. n CN The Satellite List data will x propagate the data cells iem Click Save To Device iu DENS 15 6 When the Satellite List transfer is complete at 100 a window will indicate Satellite Write Data Successfully Click Yes to exit the transfer process 7 It is good practice to power cycle the ASC1 using the master power switch on the rear of the unit o i ter Fia jobro aaraa T RC LECT Pere Sate Edit Satellite List The Satellite List is a simple 4 column and 99 row csv type file The file may be created and edited with the ASC1 Editor Excel Notepad or any text editor ASC1_Satiist_1 139w_20131215 csv OpenOffice Calc Ge Edt ew mert Format Toos Data Window Heb 131w AHC 11 295 42 46 rE EEE EE E I hisw AMC B8 125 45 45 ES wa i B U Esam Late Awc 3115343 6 P l 135w AHC 10 187 46 47 ea te x 15 11J1w Galaxy 15 220 45 45 125 Galaxy 17 2 4 45 455 127W Galaxy 13 323 45 45 LZH Galaxy 14 376 45 455 123 Galaxy lH 404 45 45 3 138W AMC 10 187 46 47 121M Galaxy 23 440 45 45 Lar ff LESH Anik FS 0 45 45 114 58W Sethe 5 0 45 45 128 Galaxy 12 294 45 dh LLIW SatMex 6 0 45 45 127W Galaxy 13 335 45 45 spiriti oiii nr deci 8 125W Galaxy 4 376 45 45 107 34 anik Fl 0 45 45 9 123W Galaxy 18 A04 45 45 105W AMC 18 0 45 45 18 121W Galaxy 23 440 45 45 delicet e Each row is a
16. osition This reference number is typically called the DiSEqC 1 2 or Motor Position in the satellite receiver s installation menu This DiSEqC 1 2 number is either preassigned by the firmware or is a user setting The important thing to remember is that the DISEqC 1 2 number assigned for each satellite in the STB must match the satellite DiSEqC 1 2 number assigned in the ASC1 This DiSEqC 1 2 motor position numbering coordination is critical If the satellite receiver is for example programmed for DiSEqC 1 2 position number 1 to be satellite G19 97w but the ASCI has been programmed for DISEqC 1 2 number to be satellite NSS1 37 5w the STB will command the ASCI to move to position 1 when satellite G 19 is selected The ASC1 will receive this command to go to position 1 it will move to satellite NSS1 This is not the fault of either the receiver or the ASC1 but simply that the system was incorrectly programmed to communicate the correct information Once the Satellite receiver and ASCI have been programmed the ASC1 will become an automatic interface between your STB and the satellite dish Whenever you change channels on your receiver or scan for channels the ASCI will automatically move the dish and set the correct polarity You may use either the receiver s menus to fine tune the dish position or you may use the ASC1 remote or front panel to fine tune both dish position and polarity offsets These fine tuned settings may be saved by either th
17. pdates and regional satellite lists are available at www TitaniumSatellite com updates Open and Close ASC1 Loader Editor Titanium ASCI Loader Editor via D x e gt o Tipim Products Titanum ASCI ASCI Firmware Titanium ASCI Loader Editor Titanium ASC 1 Loader Editor v1 4 gal Search Tita ES AM Indudeinkbrary Sharewifh Bum New folder T Hd 4j ee Name Date modified Type Sire QtCorea di 12 6 20119 35 amp M Application extension 2 240 KB BE Desktop Qiu di 8 23 2011 10 32PM Anpbeation extension 8 031K8 Bl ricum aci Loader Editer v1 4 12 17 2013 3 37PM Appbeation 185 KB l Download unzip and install the ASC1 Loader Editor on any Win XP 7 8 PC Be sure to keep the ASCI Loader Editor exe in the same folder as the two dll files Connect the included RS 232 cable from the PC to the ASCI 13 3 Launch the ASCI Loader Editor exe Your PC may may warn that the exe file is not signed and could be potentially dangerous Accept and the program will launch 4 Click Close when finished with the ASCI Loader Editor Select the Satellite Setting Tab Make sure that the ASC1 is powered ON 3 Click Read From Device 4 When the Satellite list is downloaded from the ASC1 the data will propagate the data cells NO m Save a Satellite List 1 Click Save To File Name the Satellite List csv file and set the path to save your custom Satellite List 3 Click Sav
18. rotocol as outlined above C Select Fixed on 18V if powering a single multiple LNBs or to lock a horizontal polarity on a LNBF d Select Fixed on 13V if you wish to control a switch lock a vertical polarity ona LNBF e Select OFF if the ASCI is not to provide power on the LNB port Select Save when the desired LNB output voltage has been selected LNB Type Saved prompt will be displayed Select Quit Press OK to exit and return to the main menu System Reset Often a STB will allow the user to reset the controller using the receiver s DiSeqC 1 2 installation menu If the ASCI requires a manual System Reset there are four different types of resets l 2 2 4 When any reset function is completed select Quit Reset the complete Satellite List including the positioning names amp polarity settings Reset only the Software East and West Limits Reset only the Positioner Count to 0000 Global Reset All Data To Default and press OK to return to the main menu We recommend that you use the PC software and RS 232 serial cable to back up your custom satellite list and polarity settings before performing a System Reset This simple save and reload procedure may save you hours of position and polarity reprogramming 10 Satellite List Reset l Software East West Limit Reset l Positioner Count Reset l Global Reset l Select Reset SAT Data Press OK Press OK a second time within 3 seconds
19. tal 45 and Vertical 45 12 10 11 12 13 To add add additional satellites repeat Once the feedhorn placement is correct optimize the Servo Polarity Skew setting for a horizontal transponder by BH Pizontal 42 selecting Horizontal on the ASCI Satellite Set menu Press the or Polarity Skew keys to rotate the Skew one degree at a time and optimize the signal quality This Skew fine tuning will vary between transponders on the same satellite Skew fine tuning is a wonderful function that will help optimize signal quality on any transponder and may be the difference between crystal clear reception and no signal with the digital cliff Chose a Vertical transponder on the satellite meter or STB Select Vertical then press the or Polarity Skew keys to s ertical 45 rotate the Skew and optimize the signal quality Select Save Press OK again within 3 seconds to confirm that you wish to save the satellite position and polarity settings steps 21 28 Once you are completed with manually adding satellites positions and skew offsets select Quit press OK and exit back to the Main Menu ASC1 PC Loader Editor Software A PC based software loader and editor allows the user to update the ASCI firmware via RS 232 serial connection to add new functions The Satellite List may be downloaded to the PC saved edited uploaded to the ASCI and shared with other ASC1 owners The software firmware u
20. te names Visit the support section of www TitaniumSatellite com for software satellite lists and firmware upgrades that will add even more exciting functions and features to your ASC1 The heavy duty 36Vdc 5 amp power supply exceeds every other consumer controller available Effortlessly lifts large heavy dishes and overcomes wind loads and large snowfalls A proprietary function ramps in and out of motor movements to reduce the wear and tear on the motor and support hardware IEC power connector and switchable AC input 115 230Vac 50 60hz allows the ASCI to be operated anywhere in the world Separate power source for polarity servo control and another for LNB LNBFs and switches Switchable LNB power settings of 13 18Vdc reversed 18 13Vdc fixed 18Vdc or 13Vdc 450mA provides many power options for your system Visit www TitaniumSatellite com for expanded owners manuals operational videos and a FAQ section These support materials are being continuously updated as new features are introduced Please contact us with any questions or suggestions for product improvement Thank you for your purchase Table of Contents Important Safeguards 3 Specifications 5 Front Panel amp Remote Control Keys 6 Rear Panel 7 Installation Actuator Connection 8 Software Limits 9 Polarity Servo amp LNB Connection 9 LNB Power Setting 10 System Resets 10 Backlight Timeout 12 Programming Satellite amp Polarity Settings 12 RS 232 Serial
21. to turn off the Master Power Switch if this wire swap is required Carefully watch the dish during the movement to the Eastern limit to be sure that the dish does not contact any object and the motor does not bind or the dish flops Back the dish up a few clicks from the mechanical hardware limiter stop Select Set as EAST Limit and press OK EAST Limit Saved prompt will be displayed Arrow down to Select Quit then Press OK to exit Soft Limit Set Menu and return to the Main Menu Polarity Mechanical Servo Connections optional l Feedhorn Power OFF the ASCI Master Power Switch Connect the ASC1 three Servo terminals to the mechanical polarity servo connections using 18 22AWG wire If the group has a shield bond to the Ground terminal Typically the 5Vdc color code is red color Pulse Skew is white and Ground is OEOROR fe LE black Servo REC LNB Connection l Connect the LNB port to the LNB s or LNBF using a quality RG6 coax cable If your system has multiple LNBs or LNBFs consult with the supplier of the switches to establish correct connections and path Power ON the ASCI Master Power Switch LNB Power Setting l Select LNB Type Set Press OK a Select H 18V V 13V if a connected STB will control the voltage polarity of a voltage polarity controlled LNBF or using a voltage controlled multi switch b Select H 13V V 18V if you wish to reverse the typical polarity switching p
Download Pdf Manuals
Related Search