Streacom - F7C Evo - User Guide
Contents
1. STREACOM ATEO USER GUIDE V a Index Foreword a Product Overview niente Preparation for Assembly A Installing the Motherboard das Installing Case Fan amp Optional IRRC e Wiring Diagram E eee Fitting the Optical amp Hard Drives A Installing a PCI Card er Replacing the Top Panel 053 Lo PEPA Notes Foreword Thank you for your purchase of this Streacom product Every care has been taken to ensure that it meets with the highest standards and quality that we have set for ourselves Should you have any questions that are not covered in this user guide support can be given via email through our website at www streacom com We sincerely hope that you enjoy using our product Specification Chassis Material Available Colours Motherboard Compatibility Hard Drive Support Optical Drive Support Component Cooling Front Ports External Dimensions Expansion Slot Power Supply Support IR Support Net Weight Key Features le Power Button FR Power LED de ODD Loading Slot Mikes ODD Eject Button Oia Top Panel De USB Ports 2 0 amp 3 0 Aluminum Silver Black sandblasted finish Mini ITX 1X29 1X295 07353 Slot loading drive universal eject button 1 x 80x80x25mm Fan Not Included 2 x USB ports 2 0 3 0 compatible USB 3 0 not included 240 x 250 x 100mm WxDxH 1 x Low profile expansion card NanoPSU amp external DC adapter not included MCE compatible IR receiver amp remote not inc2. C user guide INSTALLING THE CHASSIS FAN amp IRRC OPTIONAL P7 Motherboard USB 2 0 Connector USB 3 0 Connector USB 2 0 Cable x 2 NC SHIELD GND D D 5V Front USB Ports PCB USB 3 0 Connector USB 3 0 Cable Sold Separately HDD HDD RESET1 RESET1 NC Chassis Power Switch PCB Cable colours shown are for illustrative purposes only actual colours will vary Fitting the Lower Hard Drives With the cage out of the chassis begin by fitting the lower hard drive This procedure can be skipped if you only plan to install a single 2 5 hard drive The lower mounting can accommodate either 1 x 3 5 or 1 x 2 5 hard drive Depending on which drive you are using use the appropriate screws and mounting holes as shown Please also ensure that the CPU cooler fitted to the motherboard is low profile to allow for the extra height of a 3 5 drive aN 6 i FITTING THE OPTICAL amp HARD DRIVES P9 Fitting the Primary Hard Drive amp Optical Drive Before fitting the slot loading drive affix a self adhesive rubber pad included in the accessory bag to the drives eject button Mount the slot loading drive using 4 screws 2 either side Do not fully tighten the screws as the position of the drive will need to be adjusted to ensure correct operation of the eject button With left side eject buttons 2 pads may be required The primary 2 5 hard drive is mounted behin
3. d the optical drive using 4 screws as shown in the diagram Self Adhesive a Rubber Pad P10 FITTING THE OPTICAL amp HARD DRIVES Replacingthe HDD ODD Cage With all the drives now fitted to the cage carefully lower it into the chassis Note that the front mounting points are under the screw holes and the back are above li ji Replace the 4 screws to secure the cage in place i AWW i nh ny A Fa K N if y i q A al d N Ny we E i Adjust the position of the optical drive so that the drive eject button makes light contact with the chassis eject button bar Test that the button operates correctly by listening for the eject button clicking sound when pressing the chassis eject button Once the correct position has been found tighten the 4 screws to secure the optical drive In place FITTING THE OPTICAL amp HARD DRIVES P11 Installing PCI Card Optional To install an expansion card first remove the pre installed PCI blanking plate by removing the single lower screw The PCI mount can also be removed to make it easier to install the expansion card This is done by removing the 2 screws either side on the mount P12 INSTALLING THE PCI CARD Carefully place the card into the motherboard slot ensuring the rear side where the ports are located firstly passes through the expansion slot opening of the chas
4. luded 2 9KG 13 USB PCB 14 Power Button PCB Seen IR Receiver Window 8 DC Power Jack Hole Qnn 80mm Fan Bracket 10 10 Shield Opening 11 HDD ODD Cage 12 PCI Slot Half Height Requires USB 3 0 cable which is sold separately OVERVIEW P3 Removing the Top Panel The top panel is held in place with 4 screws all of which are accessible from the under side of the chassis Remove the screws and slide the top panel upwards away from the chassis Removing the HDD ODD Cage The HDD ODD cage is held in place by 4 screws which are all accessible from the top as shown Once all 4 screws are removed lift the cage out of the chassis P4 PREPARING FOR ASSEMBLY Prepare the Motherboard Assemble the motherboard by installing the RAM CPU and CPU Cooler When choosing a CPU Cooler for the F7C it is important to purchase a low profile Cooler that will not interfere with the HDD ODD cage The choice of motherboard CPU position and hard drives i e using a 3 5 drive will influence the type of CPU Cooler that can be used In general the CPU cooler height should be less than 30mm Always take the proper precautions when handling these sensitive components Installing the I O Shield Locate the 1 0 shield that is supplied with your motherboard and firmly push it in place Ensure that it clicks In place fully otherwise the motherboard will be difficult to fit In
5. sis Once the card is fully seated into the motherboard replace the PCI mount and finally secure the card with the single screw from underneath the mount Replace the Top Panel With all the components installed the chassis can now be closed Prior to doing this ensure that all cables are connected and all components are securely fitted Replace the top panel and secure it in place using 4 screws from under the chassis Connect Power amp Other Cables With the chassis now fully assembled all that remains is to connect the power and other cables REPLACING THE TOP PANEL P13 P14 NOTES NOTES P15 TRAE Melbournestraat 56 3047 BJ Rotterdam The Netherlands www streacom com
6. stalling the Motherboard Carefully lower the motherboard into the chassis with the I O port side leading so that the ports fit into the I O shield When the motherboard Is correctly in position fix it to the chassis stand offs using the screws provided Ensure that all the holes correctly align before fully tightening the screws P6 INSTALLING THE MOTHERBOARD Connect the PSU amp Other Cables With the motherboard in place you can now connect the PSU and any other internal connectors such as the power button switch You should also connect the SATA cables in perpetration for installing the HDD ODD cage assembly Connect the front USB ports to the motherboard with the cable supplied See diagram on next page for details Fitting the Chassis Fan The F7C can accommodate a single 80x80x20mm fan to extract warm air from the chassis The fan Is not supplied with the chassis and must be purchased separately To install the fan align it with the fan bracket and secure it in place with 2 screws as shown Ensure the airflow direction is towards the outside of the case Fitting the Optional IR Module The F7C is designed to accommodate the Streacom IRRC remote control and IR receiver sold separately 4 N N If you have purchased the IRRC it should be Y VAR mounted to the front of the chassis near the IR Oak window using 2 screws in the position shown Connect the cables as shown in the IRR
Download Pdf Manuals
Related Search