Operating instructions - OPERTIS Produktkatalog
Contents
1. Fitting has wrong date or wrong time Reset the time refer to the eLOCK software system documentation Batteries are empty or defective Change the battery and use an identifier to operate the APS Comfort system for flush doors once Connect an external power supply to the outside of the APS Comfort system for flush doors Then change the battery and use an identifier to operate the APS Comfort system for flush doors at least once The antenna connector has loosened or detached itself Plug in the antenna connector fully Antenna is defective Replace the antenna Cables are crushed or Replace the APS clamped Comfort system for flush doors There are chips or Replace the APS lubricant in the Comfort Comfort system for system flush doors 16 OPERTIS 09 2013 Operating instructions GB APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 Problem Possible cause Solution The lever handles are not in the horizontal position APS Comfort system for flush doors is not working properly Lever handles installed at an angle or under pressure Install the lever handles correctly and check for smooth and easy movement The lever handles are too heavy Replace the existing lever handles with lighter ones or use an additional retraining spring Each identifier is Fitting is not Program the fitting authorised for the2. The management and programming including the issue of access authorisations is carried out using the eLOCK Center Optional programming with eLOCK Lern L sch using three programming keys and without additional software is also possible Various types of passive identifiers without their own power supply such as key fobs cards and customised types are available for authorisation at the fittings Detailed information Further information on the product is given in Section 8 Product specification 09 2013 OPERTIS 7 GB eLOCK APS Comfort system for flush doors Operating instructions ES7660 ES6660 ES7661 ES6661 3 intended use Area of use The APS Comfort system for flush doors conforms to the installation dimensions for a mortice lock in accordance with DIN 18251 and is designed for use on rebated and unrebated interior doors Use on external doors is only allowed if the electronics are installed in the protected interior Use on fire doors or outdoors e g in fences is not allowed The lock meets the requirements for doors on escape routes in accordance with EN 179 and 1125 Approved tested fittings are used Condition of the product APS Comfort systems for flush doors may only be used if they are in faultless technical condition Independent modifications and changes to the product are not allowed Ambient conditions Use in particularly difficult environments e g aggressive gases high humidity extre
3. AENA 20 O ee N REN EEE Tee en 20 Pr d ct packaging E LERNTE 20 PP O PEA II Curtennenedunaiaanes 20 09 2013 OPERTIS 3 GB eLOCK APS Comfort system for flush doors Operating instructions ES7660 ES6660 ES7661 ES6661 1 Introduction About these instructions These instructions contain important information on operation of the APS Comfort systems for flush doors ES7660 ES6660 ES7661 and ES6661 O Read through the instructions carefully O Keep the instructions in a safe place and pass them on to each subsequent owner user of the APS Comfort system for flush doors Explanation of the symbols and signal words used A WARNING Indicates hazards which could result in severe or fatal injuries A CAUTION Indicates hazards which could result in minor or moderate injuries Indicates hazards which could result in damage to property Indicates information and tips for optimum use of the instructions and the product CAUTION Note Target group These instructions are directed at competent personnel entrusted with the servicing care disposal and maintenance of fault free operation of the APS Comfort system for flush doors and who have received suitable training for these activities or have appropriate experience OPERTIS Support If you have any questions which are not answered by the information provided in these instructions please contact OPERTIS GmbH Prof Bier Stra e 1 5 D 34454 Bad Arolsen Tel 49 56
4. of the fitting 09 2013 OPERTIS 9 GB eLOCK APS Comfort system for flush doors Operating instructions ES7660 ES6660 ES7661 ES6661 CAUTION Unauthorised access As an anti panic lock the inside lever handle of the APS Comfort system for flush doors is basically coupled This means that the door can be opened at any time using the inside lever handle Please bear this in mind especially if using the fitting on doors accessible to the public and doors where the inside lever handle can be easily accessed from the outside CAUTION Unauthorised access In the as delivered condition the APS Comfort system for flush doors is in construction site mode Access is possible with any OPERTIS identifier even if unprogrammed Immediately following installation you should program the authorisations to prevent unauthorised access refer to the eLOCK software system documentation at the same time you must check the time and if necessary reset it 10 OPERTIS 09 2013 eLOCK GB Operating instructions APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 5 Use and Operation Programming fittings and identifiers Fittings and identifiers are programmed using the eLOCK Center management software or the eLOCK LernL sch system More detailed information is given in the eLOCK system documentation software Change the battery Note Note the details of the battery type given in the Technical data section
5. 91 87741 200 Fax 49 5691 87741 281 Email support opertis de 4 OPERTIS 09 2013 eLOCK GB Operating instructions APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 Up to date information All details of the product images dimensions and versions are correct at the time of delivery of the product We reserve the right to make changes in line with technical progress and the resulting continuous improvement process of our products The current version of these instructions and further information is also available on our internet site www opertis de Dated 09 2013 09 2013 OPERTIS 5 GB eLOCK APS Comfort system for flush doors Operating instructions ES7660 ES6660 ES7661 ES6661 2 Product description Component parts The following drawing shows the component parts of the APS Comfort system for flush doors A 1 1 Stainless steel cap 2 Battery 3 M3x6 screws 4 Housing with electronics 5 M3x9 setscrews 6 Mounting plate 7 M4xM4 and M4xM5 screw in cams 8 APS lock 9 Forend screw M5x80 10 Profile cylinder adapter with antenna cable 11 Profile cylinder housing 12 Countersunk screw M4 dependent on door thickness 13 Profile cylinder cover made of plastic with antenna 6 OPERTIS 09 2013 eLOCK GB Operating instructions APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 Functional
6. OPERTIS Operating instructions APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 eLOCK GB Operating instructions APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 Contents 1 Introduction 4 About these INSIUCH ONS asien aaa nennen 4 Explanation of the symbols and signal words used 44s4s4s4enenenen nennen 4 VAINA AAA 4 As A A no AA iai 4 Up to date Mo NAO un 5 2 Productdescription ssassn nanasan aaaea ddaa i daad aaa dadada aai aiaa 6 COMPONEN 1 DATS Ae ASEA EAT A ETIE iio 6 FURIA pN O IE A arena ek GRAN ee A 7 Detalled iMol alone iaa 7 3 Intended AAA nee 8 Aresot User ann O eaaets 8 Condition OT TAS DIOQUEE ae 8 Ambient conditions ae teen meer NEO IR OIEA ENT Re 8 POW SF SUD ONY se ana AO ea neers Rameau 8 PIOSIGU AUIS pasate ctaest dee Sut aniuntdsacneacseenseladende EEE EEE 8 4 Safety INStructONS iio ani 9 5 Use and OPM ii deassiavduansuendeaucia aaa aa 11 Programming fittings and identifiers usas ao 11 Ghange the Dalton ana ill nates 11 Acolistie SMS 12 6 Servicing Cleaning and Maintenance uunsssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 13 eva Sernac 13 Cleaning and Maintenance aa alas Gaetan 13 SOMO add 14 7 Problems and SOLUTIONS iciciicicinccininniiin nennen idad iia 16 8 PFOGUCE specifications cur 18 Declaration of CONO ken 18 A re ER ENTE 18 TEC 19 9 Disposal i a a r ci 20 Product er ASA AA
7. PERTIS 09 2013 eLOCK GB Operating instructions APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 4 Safety instructions The following safety instructions must be noted and followed before use OPERTIS does not accept any liability whatsoever for personal injuries or damage to property caused by failure to follow these instructions A WARNING Risk of personal injuries due to the batteries Improper handling of the batteries results in health damage Note and comply with the following instructions Only use batteries supplied or approved by OPERTIS Do not open solder or weld batteries Do not throw batteries into a fire Do not recharge the batteries Remove empty batteries from the fitting immediately Keep batteries out of reach of children Do not touch leaked batteries without appropriate protection Do not bring into contact with the eyes or mouth O000000 CAUTION Risk of damage to property Malfunctions can occur if unapproved types of battery are used The fitting then does not signal any battery warnings and does not switch to the secured final state of Active Power Off Only use battery types approved by OPERTIS CAUTION Risk of being locked in or out Without a properly functioning fitting the door cannot be opened when the latch drops into the lock When installing the system or changing batteries keep the door open or ensure that the door can be opened at any time without use
8. Proceed as follows Step Activity Figure 1 Screw the M3x9 setscrews into the mounting plate and remove the stainless steel cap Remove the battery Insert a new battery in the battery compartment making sure that the battery is inserted with the correct polarity See figure 4 Place the stainless steel cap on the top of the mounting plate and hook into place 5 Attach the stainless steel cap to the bottom of the mounting plate using two M3x9 setscrews 6 Perform a closing action by holding an authorised identifier in front of the antenna Check the date and time and if necessary reset see eLOCK software system documentation 09 2013 OPERTIS 11 GB eLOCK APS Comfort system for flush doors Operating instructions ES7660 ES6660 ES7661 ES6661 Acoustic signals The acoustic and visual signals of the Comfort system for flush doors depend on the programming The programmed fittings in the AddDelete system and the fittings programmed using eLOCK Center have a different signalling concept Note The complete visual and acoustic signals are included in the eLOCK system documentation Signalling Concept section Acoustic signal Meaning 1x ascending sound sequence Programming mode on 1x descending sound sequence End of programming mode automatic 1x short high pitch Fitting connection by authorised identifier 1x long low pitch No fit
9. ce with the essential requirements and and other relevant standards of the Directives 1999 5 EC and 2011 65 EU and conform to CE A copy of the Declaration of Conformity can be obtained through OPERTIS Support Installation in mortice locks prepared for profile cylinder in accordance with DIN 18251 Locks Mortice locks Part 1 Mortice locks for rebated doors The lock has a regulatory test certificate issued by the MPA Dortmund It is marked accordingly Dimensions All dimensions given in mm ES7660 and ES6660 83 G O O 18 OPERTIS 09 2013 eLOCK Operating instructions GB APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 Technical data Surface Forend Stainless steel Profile cylinder cover Polyamide surface Masking cap Power supply Stainless steel Supply voltage 3 volt lithium battery CR 3V OPERTIS Art No ES0893 Battery life depending on use conditions and fitting O Ready to use with approx 10 closures per day O Closures total O Standby time Specific data Operating temperature type O up to 3 years O O up to 100 000 closures O upto 5 years 0 C to 45 C Storage temperature 20 C to 60 C Humidity for operation and storage max 95 non condensing Degree of protection to EN 60529 IP 21 Lock strength to DIN 18251 Class 4 Increased burglar res
10. il or grease to get inside the electromechanical lock Do not let any cleaning agents to get inside the lock case Step Activity Figure 1 Wipe down the surfaces with a damp cloth 2 Lightly grease the slanted face of the extended latch 09 2013 OPERTIS 13 GB eLOCK APS Comfort system for flush doors Operating instructions ES7660 ES6660 ES7661 ES6661 Servicing AN CAUTION Risk of being locked in or out Without a properly functioning fitting the door cannot be opened when the latch drops into the lock Carry out functional checks while the door is open The following functional checks must be carried out at least once a year Step Activity Result 1 Check for secure fit of the All components of the APS lock the installed fittings and Comfort system for flush doors the screws are securely installed The latch and the release lever move smoothly and easily 2 Press the outside lever The outside lever handle is not handle engaged The latch is not retracted 3 Hold an authorised OPERTIS The latch is retracted and after identifier in front of the reading pulling back moves back out unit then press the outside again automatically lever handle Press the inside lever handle Check the self locking The latch and the release lever must spring out The latch and the release lever cannot be pressed in 6 Check the panic function The latch and the release With the lock loc
11. ing instructions APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 09 2013 OPERTIS 23 OPERTIS Ce OPERTIS GmbH Prof Bier Stra e 1 5 D 34454 Bad Arolsen Telefon 49 5691 87741 0 Telefax 49 5691 87741 310 info opertis de www opertis de M7000 63GBB V001 09 2013
12. istance and high user frequency VdS Association of German Property Insurance Companies inspection The lock has been tested and approved by the VdS Memory capacity in the fitting ES6xxx ES7xxx ES7xxx LernL sch Identifier 60 000 80 000 100 Protection zones membership 296 30 of a group of fittings Events memory authorisation 512 628 attempts 09 2013 OPERTIS 19 GB eLOCK APS Comfort system for flush doors Operating instructions ES7660 ES6660 ES7661 ES6661 9 Disposal Product X Disposal in accordance with WEEE Directive 2012 19 EC O Do not dispose of product in the local household waste O Send product back to OPERTIS or dispose of it at a communal collection point for hazardous electronic wastes Batteries X O Do not dispose of batteries in the local household waste system but instead at the public battery collection points O Do not throw batteries into a fire O Do not store used batteries together O Only dispose of batteries if they are discharged Product packaging The product packaging must be disposed of through the local household or paper waste collection facility Notes 20 OPERTIS 09 2013 eLOCK GB Operating instructions APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 09 2013 OPERTIS 21 GB eLOCK APS Comfort system for flush doors Operating instructions ES7660 ES6660 ES7661 ES6661 22 OPERTIS 09 2013 eLOCK GB Operat
13. ked press the ver are drawn in by the inside lever handle actuation of the lever handle Press in the release lever 7 Check the panic function With the lock locked press coupled outside lever handle 14 OPERTIS 09 2013 eLOCK Operating instructions GB APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 Step Activity Result CAUTION Risk of being locked out When closing the door from the outside you must have an authorised identifier in order to re open the door Close the door from the inside The lock bolt must spring out Press the inside lever handle or the coupled outside lever handle The latch and release lever are retracted the bolt must not rub against the locking plate Read the fitting information refer to the eLOCK software system documentation 09 2013 OPERTIS 15 GB APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 eLOCK Operating instructions 7 Problems and solutions Problem Possible cause Solution The APS Comfort The identifier is not an Use an OPERTIS system for flush OPERTIS identifier for identifier doors does not open or close the locking system The identifier is not programmed or does not have the necessary authorisations Program the identifier refer to the eLOCK software system documentation Identifier is defective Replace the identifier
14. me temperatures or very dusty environment is not allowed If you have any questions please contact OPERTIS Support Power supply All battery operated fittings activate acoustic battery empty warnings and controlled false closures when the battery power in the fitting is drawing to an end The battery should then be replaced without delay In the event of repeated ignoring of the battery empty warning the APS Comfort system for flush doors permanently decouples the lever handles Active Power Off The Active Power Off state is signalled by an acoustic warning see Operating Instructions Chapter 5 Operation and Control This state is retained until the battery is replaced or if applicable an external power supply is provided on the outside of the door beforehand Residual risk If used properly as intended and in compliance with the maintenance instructions this product will help to maintain your property security However the following residual risks cannot be excluded O There is a risk of being locked out if the electromechanical components fail O If the battery is suddenly and completely discharged the APS Comfort system for flush doors does not work lt does not signal any battery warnings and does not switch to the Active Power Off state The door can then only be opened from the outside of the door using the external power supply EPS ES6781 for ES5000 plus systems or ES7781 for eLOCK and eLOCK LernL sch systems 8 O
15. principle Self locking motor panic lock with integrated electronics in accordance with DIN 18251 The OPERTIS eLOCK locking system ensures continuous consistent fitout of a building Special fitting solutions are available for different door types The APS Comfort system for flush doors includes a self locking lock which locks automatically when the door is closed There is no locking in the conventional sense with a knob or key mechanical locking is no longer necessary With the APS Comfort system for flush doors the inside door lever handle is always coupled Thanks to the integrated anti panic function when the inside door lever handle is pressed the latch and release lever are drawn back the door can always be opened from the inside The panic function cannot be switched off With the APS Comfort system for flush doors the outside door lever handle is in an uncoupled state and has no function It can be pressed but has no connection with the latch and release lever In this state the door cannot be opened using the outside door lever handle The access organisation is implemented by short term coupling of the otherwise empty running outside door lever handle after holding an authorised identifier in front of the antenna When the coupled outside door lever handle is pressed the latch and release lever are pulled back There is no unlocking in the conventional sense with a knob or key mechanical unlocking is no longer necessary
16. programmed refer to the eLOCK lock construction site software system mode documentation Latch does not engage The latch cut out in the strike plate does not match the latch position ofthe APS Comfort system for flush doors Adjust the latch cut out in the strike plate so that it matches the latch position ofthe APS Comfort system for flush doors Door or doorframe is warped Adjust door or doorframe or rather the hinges The lock does not The self locking is Replace the lock lock defective immediately The lock bolt is not The panic function is Replace the lock retracted when the defective immediately inside lever handle or coupled outside lever handle is pressed The door must not be closed as the panic function is no longer available The APS Comfort system for flush doors is permanently coupled The door can be opened without the authorisation of an identifier The fitting s switch mode is activated see eLOCK system documentation Fitting modes section Deactivate switch mode O Reconfigre the fitting time profile O Authorisation with Switch IT in order to deactivate the switch mode OPERTIS 17 GB eLOCK APS Comfort system for flush doors Operating instructions ES7660 ES6660 ES7661 ES6661 8 Product specifications Declaration of Conformity OPERTIS GmbH herewith declares that the APS Comfort systems for flush doors are in accordan
17. ting connection identifier not authorised 1x long low 5x sound sequence short high Battery empty warning level 1 with controlled failed locking 1x long low 3x sound sequence short high Active Power Off battery completely discharged 1x short high pitch Fitting connection in construction site mode or permanent release mode see eLOCK system documentation Fitting Modes section 1x long low pitch 4x short low pitch System error Dismantle Comfort system contact OPERTIS Support 12 OPERTIS 09 2013 eLOCK Operating instructions GB APS Comfort system for flush doors ES7660 ES6660 ES7661 ES6661 6 Servicing Cleaning and Maintenance Maintenance and cleaning may only be carried out by qualified personnel We do not provide any warranty whatsoever for damage caused by improper handling Intervals Activity Interval Cleaning and maintenance 3 months Maintenance Cleaning and maintenance CAUTION 1 year Material damage due to incorrect cleaning Incorrect cleaning can cause attack and damage to the surfaces O Clean and maintain the APS Comfort system for flush doors from the outside only do not remove the cover caps agents O 000 O Proceed as follows Do not use alkali acidic or chlorine containing cleaning Do not use cleaning agents containing abrasive additives Do not use abrasive instruments e g brushes Do not let any o
Download Pdf Manuals
Related Search