Operating Instructions - ACS-Control
Contents
1. or nor And And P Here the switching behavior of the relay is defined via a logic link the following schema describes these functions with inclusion of AL and AL 2 This parameter can only be selected if LOGIC was selected under REL 1 A1lvA2 As soon as a selected alarm is activated the relay operates Equates to operating current principle mor A1v A2 A1AA2 The relay operates only if no selected alarm is active Equates to quiescent current principle An g Ai Aa2 The relay operates only if all selected alarms are active niin ad A1AA2 A1v A2 As soon as a selected alarm is not activated the relay operates With P the selection is confirmed and the device changes into menu level Alarms for relay 2 COf e Default A 2 AL Ae ALi2a4 P The allocation of the alarms to relay 1 happens via this parameter one alarm or a group of alarms can be chosen This parameter can only be selected if LOGIC was selected under REL 1 With P the selection is confirmed and the device changes into menu level Back to menu group level RET With P the selection is confirmed and the device changes into menu group level REL ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden Iwww acs cont2. Fs rE cEUR o E For the operation mode special functions can be deposited on the O key This function is activated by pressing the key SET OF adds a defined value to the currently displayed value EHT RE deletes the min max memory ACTUA shows the measuring value for approx 7 seconds after this the device switches back onto the parameterised display value If NO is selected the O key is without any function in the operation mode Back to menu group level RET With P the selection is confirmed and the device changes into menu group level FLT 1 6 ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de 5 4 3 Safety parameters Menu group level n Pl Menu level Adjustment of user code U CODE Default 0000 g e gege geg ge Li Via this code reduced sets of parameters QUT LE and AL LEV can be unlocked during locked programming Further parameters are not available via this code The U CODE can only be changed via the correct input of the A CODE Master code Master code A CODE Default 1234 70 9g 978428 By entering A CODE the device will be released and all parameters unlocked Release lock analog output parameter
3. Each setpoint optional can be linked up via 4 alarms by default This can either be inserted at activated alarms ALI 4 or deactivated alarms ALNI Y If LOGIC is selected logical links are available in the menu level LOG I and CON I Access to these two menu levels is via LOGIC at all other selected functions these two parameters are overleaped Via ON OFF the setpoints can be activated deactivated in this case the output and the setpoint display are set not set on the front of the device With P the selection is confirmed and the device changes into menu level Logic relay 1 L06 1 Default OR or alr And And P Here the switching behavior of the relay is defined via a logic link the following schema describes these functions with inclusion of AL and AL 2 This parameter can only be selected if LOGIC was selected under REL or A1v A2 As soon as a selected alarm is activated the relay operates Equates to operating current principle non A1VA2 A1TAA2 The relay operates only if no selected alarm is active Equates to quiescent current principle Alan g A1 a2 The relay operates only if all selected alarms are active nan a ATAA2 AIVA2 As soon as a selected alarm is not activated the relay operates With P the selection is confirmed and the device changes into menu level
4. Os OTe Da Coon The decimal point and the physical unit of the device can be adjusted with Y A If e g temperature measurement is selected in C one can select 0 C respectively 0 0 C in the parameterisation level Confirm the selection with P and the display switches back to menu level Reference junction correction OFFS Default 0 0 z PF P 5 g 8 g P g P E v P The value for the sensor calibration is aligned from the smallest to the highest digit Y A and confirmed digit per digit with P After the last digit the device changes back into menu level During a temperature measurement in C the value calibration can be adjusted between 20 0 and 20 0 and can be set during a measurement in F between 36 0 and 36 0 The adjusted offset temperature is added on the reference junction temperarture and then allocated as a proportional thermo voltage An alignment of the offset needs to be done based on a reference temperature of the reference junction temperature generally 10 C 40 C If the measurement is switched later on the value is rounded ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden Iwww acs controlsystem delinfo acs controlsystem de 1 3 Menu level Parameterisation level Setting up the display time SEC Default 1 0 A D 4 The display time is set with A Y The display moves up in increments
5. level 4 v R EEE IL n x 0 P or x P Parameter am level Underline P Takeover lO stop A Value selection AZ Value selection 4 1 Parameterisation software PM TOOL Part of the PM TOOL are the software on CD and an USB cable with device adapter The connection happens via a 4 pole micromatch plug on the back side of the device to the PC side the connection happens via an USB plug System requirements PC incl USB interface Software Windows XP Windows VISTA With this tool the device configuration can be generated omitted and safed on the PC The parameters can be changed via the easy to handle program surface whereat the operating mode and the possible selection options can be preset by the program CAUTION During parameterisation with connected measuring signal make sure that the measuring signal has no mass supply to the programming plug The programming adapter is galvanic not isolated and directly connected with the PC Via polarity of the input signal a current can discharge via the adapter and destroy the device as well as other connected components ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden Iwww acs controlsystem delinfo acs controlsystem de 5 Setting up the device 5 1 Switching on Once the installation is complete you can start the device by applying the voltage supply First check once again that all electrical connections are correc
6. Alarms for relay 1 ON Default 7 7 RAID ae Aie34 4 P The allocation of the alarms to relay 1 happens via this parameter one alarm or a group of alarms can be chosen This parameter can only be selected if LOGIC was selected under REL 1 With P the selection is confirmed and the device changes into menu level 20 ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de Menu level Parameterisation level Alerting relay 2 REL 2 Default AL 2 AL I nm mi 1 Lou OFF Lin Each setpoint optional can be linked up via 4 alarms by default This can either be inserted at activated alarms ALI Y or deactivated alarms ALNI If LOGIC is selected logical links are available in the menu level LQ6 and Con 1 Access to these two menu levels is via LOGIC at all other selected functions these two parameters are overleaped Via ON OFF the setpoints can be activated deactivated in this case the output and the setpoint display are set not set on the front of the device With P the selection is confirmed and the device changes into menu level Logic relay 2 LOG 2 Default OR
7. 57 1D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de 1 Brief description The panel meter DAL 111 is a 5 digit device for several thermocouple types and a visual threshold value moni toring via the display The configuration happens via four front keys or via the optional PC software PM TOOL An integrated programming interlock prevents unrequested changes of the parameters and can be unlocked again by an individual code Optional the following functions are available a supply for the sensor a digital input for triggering of Hold Tara or an analog output for further processing in the equipment By use of the two optional galvanic isolated setpoints free adjustable threshold values can be controlled and reported to a superior master display The electrical connection is carried out on the back side via plug in ter minals Selectable functions like e g the request of the min max value an average determination of the measuring signals a nominal preset respectively setpoint preset a direct change of threshold value in operation mode and additional measuring supporting points for linearisation complete the modern device concept ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de 2 Assembly Please read the Safety advices on page 25 before installation and keep this user manual for future reference Gap for physical unit
8. la P v The difference to the threshold value that causes the delay of the actuation of the alarm is defined by the hysteresis Function if display falls below exceeds limit value FU 2 Default HIGH EH S Louie 4 E The limit value undercut can be selected with LOUU LOW lower limit value and limit value exceedance can be selected with HIGH HIGH upper limit value If e g limit value 1 is on a switching threshold of 100 and occupied with function HIGH the alarm will be activated by reaching the threshold If the limit value is allocated to LOW an alarm will be activated by undercut of the threshold User code 4 digit number combination free available U CODE Default 0000 g e g 2 If this code is set gt 0000 all parameters are locked for the user if LOC has been selected under menu item RUN By pressing P for approx 3 seconds in operation mode the message CODE is shown in the display Enter the preset U CODE to get access to the for the user unlocked set of parameters The code needs to be entered bevor each try of parameterisation as long as A CODE Master code all parameters are unlocked again ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden Iwww acs controlsystem delinfo acs controlsystem de 1 1 Menu level Parameterisation level Master code 4 digit number combinati
9. selected in C one can select 0 C respectively 0 0 C in the parameterisation level Confirm the selection with P and the display switches back to menu Reference junction correction OFFS Default 0 0 5 Po Pla rie E g eg e geg ae The value for the sensor calibration is aligned from the smallest to the highest digit V 4 and confirmed digit per digit with P After the last digit the device changes back into menu level During a temperature measurement in C the value calibration can be adjusted between 20 0 and 20 0 and can be set during a measurement in F between 36 0 and 36 0 The adjusted offset temperature is added on the reference junction temperature and then allocated as a proportional thermo voltage An alignment of the offset needs to be done based on a reference temperature of the reference junction temperature generally 10 C 40 C If the measurement is switched later on the value is rounded ACS CONTROL SYSTEM GmbH Lauterbachstr 57 D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de 9 Menu level Parameterisation level Setting up the display time SEC Default 1 0 mart Mm LI Lt I ja M g then m Al D e The display time is set with A Y The display moves up in increments of 0 1 up to 1 second and in increments of 1 0
10. After removing the fixing elements insert the device Check the seal to make sure it fits securely Click the fixing elements back into place and tighten the clamping screws by hand Then use a screwdriver to tighten them another half a turn S CAUTION The torque should not exceed 0 1 Nm The dimension symbols can be exchanged before installation via a channel on the side ACS CONTROL SYSTEM GmbH Lauterbachstr 57 D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de 3 Electrical connection Type DAL 111x800S with a supply of 230 VAC Type DAL 111x800S with a supply of 10 30 VAC 10 30 VDC or 230 VAC Thermocouple N L gt Options 0 4 20 mA Analog output lt gt ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de 4 Function and operation description Operation The operation is divided into three different levels Menu level delivery status This level is for the standard settings of the device Only menu items which are sufficent to set the device into operation are displayed To get into the professional level run through the menu level and parameterise PROF under menu item RUN Menu group level complete function volume Suited for complex applications as e g linkage of alarms setpoint treatment totaliser function etc In this level function groups which allow an extended parameterisation of the standar
11. Bo Be 90 Ad fill level water level pressure temperature flow visualization signal converter sensoric a heated Technical features e red display of 19999 99999 digits optional green orange or blue display minimal installation depth 70 mm without plug in screw terminal min max memory e display flashing at threshold value exceedance threshold value undercut permanent min max value recording e brightness control programming interlock via access code protection class IP65 at the front side e plug in screw terminal e optional 2 relay outputs e optional analog output e accessories PC based configuration kit PM TOOL with CD amp USB adapter for devices without keypad and for a simple adjustment of standard devices ACS CONTROL SYSTEM X chnolo gy al id automation Order code power supply 230V AC 10 30V DC galvanic seperated 230V AC with sensor supply 24V DC 50 mA and digital input no analog output possible 10 30V DC galvanic seperated with sensor supply 24V DC 50 mA and digital input no analog output possible ARWNO function input 9 weighing technology function output 0 display 0 standard configuration Ss standard protection IP65 DAL 111 EEE ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de Contents 1 2 3 4 Brief description Assembly Electrical connection Functions and o
12. F needs to be set The device confirms this setting with and changes automatically into operation mode By pressing P for approx 3 seconds in operation mode the first menu group INP is shown in the display and thus confirms the change into the extended parameterisation It stays as long activated as ULOC is entered in menu group RUN thus the display is set back in standard parameterisation again 1 2 ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de 5 4 Extended parameterisation Professional operation level 5 4 1 Signal input parameters Menu group level Pl Menue Selection of the input signal TYPE Default TYP L a a i A Clo m EA YP v c Ir a P Available are 9 types of thermocouple as input options L J K B S N E T R Confirm the selection with P and the display switches back to menu level Type of temperature measurement UNIT Default C nso S p Select between C and F to display the temperature Confirm the selection with P and the display switches back to menu level Setting the decimal point physical unit DOT Default 0 0
13. M GmbH Lauterbachstr 571D 84307 Eggenfelden Iwww acs controlsystem delinfo acs controlsystem de 2 5 Resolution 0 1 C or 0 1 F Analog output 0 4 20 mA burden 350 Ohm 0 10 VDC burden 10 kOhm 16 bit Switching outputs Relay with change over contacts 250 VAC 5 AAC 30 VDC 5 ADC Switching cycles 30 x 10 at 5 AAC 5 ADC ohm resistive burden 10 x 106 mechanically Diversification according to DIN EN50178 Characteristics according to DIN EN60255 Power supply 230 VAC 50 60 Hz 10 max 10 VA 10 30 VDC galv isolated max 4 VA Data life 2 100 years at 25 C Ambient conditions Working temperature 0 50 C Storing temperature 20 80 C Weathering resistance relative humidity 0 80 on years average without dew EMV EN 61326 CE sign Conformity according to directive 2004 108 EG Safety standard According to low voltage directive 2006 95 EG EN 61010 EN 60664 1 26 ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de 9 Safety advices Please read the following safety advices and the assembly chapter 2 before installation and keep it for future reference Proper use The DAL 111 device is designed for the evaluation and display of sensor signals Attention Careless use or improper operation can result in personal injury and or cause damage to the equipment Control of the device The panel meters are checked before dispatch and sent out in perfe
14. ct condition Should there be any visible damage we recommend close examination of the packaging Please inform the supplier immediately of any damage Installation The DAL 111 device must be installed by a suitably qualified specialist e g with a qualification in industrial electronics Notes on installation e There must be no magnetic or electric fields in the vicinity of the device e g due to transformers mobile phones or electrostatic discharge e The fuse rating of the supply voltage should not exceed a value of 6A N B fuse e Do not install inductive consumers relays solenoid valves etc near the device and suppress any interference with the aid of RC spark extinguishing combinations or free wheeling diodes e Keep input output and supply lines separate from one another and do not lay them parallel with each other Position go and return lines next to one another Where possible use twisted pair So you receive best measuring results e Screen off and twist sensor lines Do not lay current carrying lines in the vicinity Connect the screening on one side on a suitable potential equaliser normally signal ground e The device is not suitable for installation in areas where there is a risk of explosion e Any electrical connection deviating from the connection diagram can endanger human life and or can destroy the equipment The terminal area of the devices is part of the service Here electrostatic d
15. d settings are availabe To leave the menu group level run through this level and parameterise ULOC under menu item RUN Parameterisation level Parameter deposited in the menu item can here be parameterised Functions that can be changed or adjusted are always signalised by a flashing of the display Settings that are made in the parameterisation level are confirmed with P and thus safed By pressing the O key zero key it leads to a break off of the value input and to a change into the menu level All adjustments are safed automatically by the device and it changes into operating mode if no further key operation is done within the next 10 seconds Change to parameterisation level and deposited values Menu level Keys for up and down navigation in the menu level Change into operation mode To confirm the changes made at the parameterization level ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden Iwww acs controlsystem delinfo acs controlsystem de Function chart Standard parameterisation Extended parameterisation Flat operation level professional operation level 7 Sr mode E Aal mode ay O0 m f IL 7 m 88888 88888 N B o x 3 peor P run gt Menu level nn T fun ULOC P A ave oT Input break _ x O P R 9 x Input break gt 10s B a P a O s CA NB P Parameter PN Menu level
16. different functions in detail this are the current measuring value min value or max value With P the selection is confirmed and the device changes into menu level Selection analog output OUT RA Default 4 20 B Bin m v i a P There are 3 output signals availabe 0 10 VDC 0 20 mA and 4 20 mA With this function the demanded signal can be selected Setting up the final value of the analog output OUT EN Default 850 0 P 2 g P g g P The final value can be adjusted from the smallest to the largest digit with A Y Confirm each digit with P A minus sign can only be parameterized on the highest value digit After the last digit the display switches back to the menu level Setting up the initial value of the analog output QUT OF Default 200 0 oy P ay Pa Po a P Li Li Li v l L The initial value can be adjusted from the smallest to the largest digit with A Y Confirm each digit with P A minus sign can only be parameterized on the highest value digit After the last digit the display switches back to the menu level 18 ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden www acs controlsystem delinf
17. fo acs controlsystem de 1 5 Menu level Parameterisation level Display flashing FLASH Default NO a 4 iv m ALH Orca CATIE Rut A display flashing can be added as additional alarm function either to single or to a combination of off limit condition With NO no flashing is allocated Assignment deposit of key functions TAST Default NO al a a v i v i Ad A For the operation mode special functions can be deposited on the navigation keys A Y in particular this function is made for devices in housing size 48x24mm which do not have a 4th key O key If the min max memory is activated with EHTR all measured min max values are safed during operation and can be recalled via the navigation keys The values get lost by restart of the device If the threshold value correction L412 or L134 is choosen the values of the threshold can be changed during operation without disturbing the operating procedure Under LIGHT the brightness can be changed during operation If NG is selected the navigation keys are without any function in the operation mode Special function O key TAST 4 Default NO
18. ischarge needs to be avoided Attention High voltages can cause dangerous body currents e Galvanic isolated potentials within one complex need to be placed on an appropriate point normally earth or machines ground So a lower disturbance sensibility against impacted energy can be reached and dangerous potentials that can occur on long lines or due to faulty wiring can be avoided ACS CONTROL SYSTEM GmbH Lauterbachstr 57 D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de 27 10 Error elimination The unit permanently indicates overflow The input has a very high measurement check the a measuring circuit e The input is open The unit permanently shows underflow e The input has a very low measurement check the measuring circuit e The input is open The word HELP lights up in the e The unit has found an error in the configuration 7 segment display memory Perform a reset on the default values and re configure the unit according to your application 4 Program numbers for parameterising of Programming lock is activated the input are not accessible Enter correct code ERRT lights up in the 7 segment display e Please contact the manufacturer if errors of this kind occur The device does not react as expected If you are not sure that the device has been para meterised before then follow the steps as written in chapter 6 and set it bac
19. k to its delivery status The displayed temperature differs from e Check if the right thermocouple type was selected the reference temperature under TYPE Slightly differences can be corrected via the reference junction correction OFFS If the parameter that needs to be compensated lies outside of 10 10 C respectively 18 18 F then you shoud search for a systematic error If the available adjustment range is not sufficient a fault in the test setup seems likely Clear drift of the displayed temperature e Avoid airflow strong heat sources or switched sinks in over time the direct vicinity of the terminal strip of the device They lead to measuring errors at the reference junction Seal off the connection are of the device if neccessary with help of iron sheets or an appropriate housing construction 28 ACS CONTROL SYSTEM GmbH Lauterbachstr 57 D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de ACS CONTROL SYSTEM GmbH Lauterbachstr 57 1D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de 29 2QCG28O0O m fill level water level pressure temperature flow visualization signal converter sensoric Wir erwarten Ihren Anruf ACS CONTROL SYSTEM GmbH Lauterbachstr 57 D 84307 Eggenfelden Tel 49 0 8721 9668 0 ACS CONTROL SYSTEM X 7 ve P info acs controlsystem de knowhow with system contsys BWIN SETOR S SEME Stand 03 2015 Your partner fo
20. ncrements of 1 0 With P the selection is confirmed and the device changes into menu level then o0 v 5 P Rounding of display values ROUND Default 00001 iS poo05 4 cog 1 cooso 4 This function is for instable display values where the display value is changed in 1 5 10 or 50 steps This does not affect the resolution of the optional outputs With P the selection is confirmed and the device changes into menu level Display DISPL Default ACTUA ACELA At nun MARUA 4 P With this function the current measurand or the min max value can be allocated to the display With P the selection is confirmed and the device changes into menu level Brightness control LIGHT Default 15 oo The brightness of the display can be adjusted in 16 levels from 00 very dark to 15 very bright via this parameter or alternatively via the navigation keys from the outside During the start of the device the level that is deposited under this parameter will always be used even though the brightness has been changed via the navigation keys in the meantime ACS CONTROL SYSTEM GmbH Lauterbachstr 57 D 84307 Eggenfelden Iwww acs controlsystem delin
21. o acs controlsystem de Menu level Parameterisation level Overflow behavior FLOU Default EDGE JE A GER EoEnd j A AH 4 To recognise and evaluate faulty signals e g by a controller the overflow behavior of the analog output can be defined As overflow can be seen either EDGE that means the analog output runs on the set limits e g 4 mA and 20 mA or TO OFF input value smaller than initial value analog output changes on e g 4 mA TO END higher than final value analog output changes on e g 20 mA If TO AIN or TO MAX is set the analog output changes on the smallest or highest possible binary value This means that values of e g 0 mA 0 VDC or values higher than 20 mA or 10 VDC can be reached With P the selection is confirmed and the device changes into menu level a rec a la Men C v Back to menu group level RET With P the selection is confirmed and the device changes into menu group level 0UT ACS CONTROL SYSTEM GmbH Lauterbachstr 57 D 84307 Eggenfelden Iwww acs controlsystem delinfo acs controlsystem de 1 9 5 4 5 Relay functions Pl Mue Alerting relay 1 REL Default AL 7 l a v Lobe DEE On P
22. of 0 1 up to 1 second and in increments of 1 0 up to 10 0 seconds Confirm the selection by pressing the P button The display then switches back to the menu level again Device undercut DI UND Default 19999 Aeplghgtgta With this function the device undercut can be defined on a definite value Exception is input type 4 20 mA it already shows undercut at a signal lt 1 mA so a sensor failure is marked Display overflow DI OUE Default 99999 5 P oy P om P py P jy P Li Lj Li v Ll With this function the display overflow can be defined on a definite value Back to menu group level RET With P the selection is confirmed and the device changes into menu group level INP 1 4 ACS CONTROL SYSTEM GmbH Lauterbachstr 57 D 84307 Eggenfelden Iwww acs controlsystem delinfo acs controlsystem de 5 4 2 General device parameters Menu group level Pl Menue Display time DISEC Default 01 0 zn amp g The display time is set up with A Y Thereby switch up to 1 second in increments of 0 1 and up to 10 0 seconds in i
23. on free available A CODE Default 7234 Grau ger After LOC has been activated under menu item RUN this code can be used for unlocking all parameters By pressing P for approx 3 seconds in operation mode the message CODE is shown in the display and offer the user access to all parameters by entering A CODE While leaving this parameterisation it can be unlocked permanently under RUN by selecting ULOC or PROF So at an anew pressing of P in operating mode an anew entereing of the code is not needed 5 3 Programming interlock Activation Deactivation of the programming interlock or completion of the standard parameterisation with change into menu group level complete function volume RUN Default ULOC a a v 2 ry P Choose between the deactivated key lock ULOC works setting the activated key lock LOC or the menu group level PROF with the navigation keys A Y Confirm the selection with P After this the display confirms the settings with and automatically switches to operating mode If LOC was selected the keyboard is locked To get back into the menu level press P for 3 seconds in operating mode Now enter the CODE works setting 1234 that appears using 4 Y plus P to unlock the keyboard FAIL appears if the input is wrong To parameterise further functions PRO
24. peration description 4 1 Programming software PM TOOL Setting up the device 5 1 Switching on 5 2 Standard parameterisation flat operation level Value assigment for triggering of the singal input 5 3 Programming interlock RUN Activation Deactivation of the programming interlock or change into the professional level respectively back into the flat operation level 5 4 Extended parameterisation professional operation level 5 4 1 5 4 2 5 4 3 5 4 4 5 4 5 5 4 6 Signal input parameter INP Value assigment for triggering of the singal input General device parameter FCT Higher device functions like min max permanent brightness control as well as the control of the keyboard configuration Safety parameter COD Assignment of user and master code for locking or access to certain parameters like e g analog output and alarms etc Analog output parameter OUT Analog output functions Relay functions REL Parameter for the definition of the setpoints Alarm parameter ALIl ALY4 Activator and dependencies of the alarms Reset to factory settings Reset of the parameter to the factory default settings Alarms Relays Function principle of the switching outputs Technical data Safety advices Error elimination N NN OO OO FP W ND 11 11 13 15 16 18 20 21 22 23 25 26 ACS CONTROL SYSTEM GmbH Lauterbachstr
25. r measuring technology and automation
26. rolsystem delinfo acs controlsystem de 2 1 5 4 6 Alarm parameters Menu group level Pl Muse Depedency of alarm 1 ALRN I Default ACTUA AEWA AWA MAHA F The dependency of alarm 1 can be related to special functions in detail these are the current measurand the min value or the max value EHTER causes the dependency either by pressing the O key on the front of the housing or by an external signal via the digital input With P the selection is confirmed and the device changes into menu level Example By using the maximum value ALARM T MAXVA in combination with a threshold monitoring FU HIGH an alarm confirmation can be realised Use the navigation keys or the 4th key for confirmation Threshold values limits L 7 Default 200 0 g e g P g P g e g e This limit value defines the threshold that leads to an activation deactivation of the alarm Hysteresis for threshold values 9 1 Default 0 0 7 e g D g P ge g se The difference to the threshold value that causes the delay of the actuation of the alarm is defined by the hysteresis Function for threshold value exceedance undercut FU Default HIGH SICH a FE P The limit
27. s QUT LE Default ALL o En OFi OLEED AEO F Analog output parameters can be locked or released for the user at EN OF the initial or final value can be changed in operation mode at OUT EO the output signal can be changed from e g 0 20 mA to 4 20 mA or 0 10 VDC at ALL analog output parameters are released at NO all analog output parameters are locked Release lock alarm parameters AL LEU Default ALL alol Ei HIE py Ali ir a ALL P l This parameter describes the user release user lock of the alarm LIMIT here only the range of value of the threshold values 1 4 can be changed ALRM L here the range of value and the alarm trigger can be changed ALL all alarm parameters are released NO all alarm parameters are locked Back to menu group level RET With P the selection is confirmed and the device changes into menu group level COD ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden Iwww acs controlsystem delinfo acs controlsystem de 1 7 5 4 4 Analog output parameters Menu group level Selection reference analog output QUTPT Default ACTUA ACEUA Aion MAHUA P The analog output signal can refer to
28. t Starting sequence For 1 second during the switching on process the segment test 8 8 8 8 8 is displayed followed by an indication of the software type and after that also for 1 second the software version After the starting sequence the device switches to operation display mode 5 2 Standard parameterisation Flat operation level To parameterise the display press the P key in operating mode for 1 second The display then changes to the menu level with the first menu item TYPE Menu level Parameterisation level Selection of the input signal TYPE Default TYP L a 7 l n 4 J v l iat fy 4 Am w E Available are 9 types of thermocouple as input options L J K B S N E T R Confirm the selection with P and the display switches back to menu level Type of temperature measurement UNIT Default C a c A Select between C and F to display the temperature Confirm the selection with P and the display switches back to menu level Setting the decimal point physical unit DOT Default 0 0 Da Coon e The decimal point and the physical unit of the device can be adjusted with V A If e g temperature measurement was
29. tching on delay is activated via an alarm and e g switched 10 seconds after reaching the switching threshold a short 0 wheels term exceedance of the switching value does 5 not cause an alarm respectively does not cause a switching operation of the relay The switching off delay operates in the same way keeps the alarm the relay switched longer for the parameterised time Switching threshold Alarm switching on delay 10 s 24 ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de 8 Technical data Dimensions 96x48x70 mm BxHxD 96x48x89 mm BxHxD including plug in terminal Panel cut out 92 0 0 8 x 45 0 9 6 mm Wall thickness up to 15 mm screw elements PC Polycarbonate black UL94V 0 EPDM 65 Shore black standard IP65 Front IPOO Back side Fixing Material Sealing material Protection class Weight approx 200 g Connection plug in terminal wire cross section up to 2 5 mm Display Digit height 14 mm Segment colour red optional green orange or blue Display range 19999 up to 99999 Setpoints one LED per setpoint Overflow Underflow horizontal bars at the top horizontal bars at the top 0 1 to 10 0 seconds at 1 second measuring time 0 1300 K Display time Type N NiCrSi NiSi Type E NiCr CuNi Type T Cu Cu Ni Type R Pt13Rh Pt 50 0 1768 0 C 1 1 1 1 1 1 1 1 1 ACS CONTROL SYSTE
30. up to 10 0 seconds Confirm the selection by pressing the P button The display then switches back to the menu level again Selection of analog output OUT RA Default 4 20 DouE OF va mi ui 1 Li ri Li a He em hd D Three output signals are available 0 10 VDC 0 20 mA and 4 20 mA with this function the demanded signal is selected Setting up the final value of the analog output OUT EN Default 850 0 m oy P iy 4 g P Gy P P g g E The final value is adjusted from the smallest digit to the highest digit with A V and digit by digit confirmed with P A minus sign can only be parameterised on the highest digit After the last digit the device changes back into menu level Setting up the initial value of the analog output QUT OF Default 200 0 g P jo m 4 g ep e geger The final value is adjusted from the smallest digit to the highest digit with A V and digit by digit confirmed with P A minus sign can only be parameterised on the highest digit After the last digit the device changes back into menu level Threshold values limit values L Default 200 0 ig ig M m 4 g g e p e g 44 1 r P This limit
31. upply and press P button until is shown in the display With reset the default values of the program table are loaded and used for subsequent operation This sets the unit back to the state in which it was supplied Caution All application related data are lost ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden Iwww acs controlsystem delinfo acs controlsystem de 23 7 Alarms Relays This device has 4 virtual alarms that can monitor one limit value in regard of an undercut or exceedance Each alarm can be allocated to an optional relay output S1 S2 furthermore alarms can be controlled by events like e g min max value Function principle of alarms relays Alarm Relay x Deactivated instantaneous value min max value or an activation via the O key Switching threshold Threshold limit value of the change over Broadness of the window between the switching thresholds Working principle Operating current Quiescent current Alarms Operating current By operating current the alarm S1 S2 is off below the threshold and on on reaching the a eee ard ees threshold A payeanoe v fallen off Off Display Hysterisis nn Klare Quiescent current By quiescent current the alarm S1 S2 is on below the threshold and switched off on Threshold reaching the threshold Orb Va Sa En 1 1 g 2 A Ve gs A Soa 7 Off Display Hysterisis Input Switching on delay 10 The swi
32. value defines the threshold that leads to an activation deactivation of the alarm Hysteresis for limit values 44 1 Default 0 0 ge gee Je P gge The difference to the threshold value that causes the delay of the actuation of the alarm is defined by the hysteresis 10 ACS CONTROL SYSTEM GmbH Lauterbachstr 57 D 84307 Eggenfelden www acs controlsystem delinfo acs controlsystem de Menu level Parameterisation level Function if display falls below exceeds limit value FU Default HIGH IGH Lown P The limit value undercut can be selected with LOUU LOW lower limit value and limit value exceedance can be selected with HIGH HIGH upper limit value If e g limit value 1 is on a switching threshold of 100 and occupied with function HIGH the alarm will be activated by reaching the threshold If the limit value is allocated to LOW an alarm will be activated by undercut of the threshold Threshold values limit values L 2 Default 300 0 0 B peg amp ge la P v m u This limit value defines the threshold that leads to an activation deactivation of the alarm Hysteresis for threshold values HY 2 Default 0 0 g0 e ge p Bge 1 u
33. value undercut can be selected with LOUU LOW lower limit value and limit value exceedance can be selected with HIGH HIGH upper limit value If e g limit value 1 is on a switching threshold of 100 and occupied with function HIGH the alarm will be activated by reaching the threshold If the limit value is allocated to LOW an alarm will be activated by undercut of the threshold 22 ACS CONTROL SYSTEM GmbH Lauterbachstr 571D 84307 Eggenfelden Iwww acs controlsystem delinfo acs controlsystem de Menu level Parameterisation level Switching on delay TON Default 000 jegeg se For limit value 1 one can preset a delayed switching on of 0 100 seconds Switching off delay TOF 1 Default 000 AAG se For limit value 1 one can preset a delayed switching off of 0 100 seconds Back to menu group level RET With P the selection is confirmed and the device changes into menu group level ALI The same applies to Al2 to ALY Programming interlock Description see page 10 menu level RUN 6 Reset to factory settings To return the unit to a defined basic state a reset can be carried out to the default values The following procedure should be used e Switch off the power supply Press button P e Switch on voltage s
Download Pdf Manuals
Related Search