Hampton Bay 11685 Instructions / Assembly
Contents
1. Item 622 472 USE AND CARE GUIDE NATURE LOG FOUNTAIN Table of Contents Table of ContentS cccssccsseeeseeeseseeeseeensseeeeeeeseeeeeeenes 2 Safety Information cccceccseeecseeeeseeeeseeeeseneeseneeseneenenes 2 VEIA lt gt AAA 3 Pre Operation coccnconnaniconnican sida anna nnn nennen 3 Planning for Successful Installation 3 Package Content c cccecceeseeseceeeeneeeeeeeeneeeeaeeees 3 Safety Information 1 The National Electric Code requires that a ground fault circuit interrupter GFCI be used in the branch circuit supplying the fountain pump and other pond equipment See your electrical supplies dealer for this device Do not use an extension cord with this pump Run this fountain from a main electricity supply only such as a normal home outlet and ensure all plug prongs connect securely into the outlet The electrical power supply has to correspond to indications on the type label Do nat pull on carry or pick up the pump by the electrical cord WARNING Do not use the pump in flammable liquids or in sewage where flammable gases are likely to occur WARNING Do not use the pump in a location where special conduits prevail such as the presence of a corrosive or explosive atmosphere dust vapor gas gt Ep CAUTION Do not use the pump in water exceeding 95 F 35 C gt ASSOMMDI Yj a ce ees 4 OOM ATON sacari2. 0L h 118G h Maximum submersion 3 0 ft 0 9 m Retain this manual for future use
3. d misused cut or worn This warranty does not cover use in commercial applications The manufacturer DISCLAIMS all other implied or express warranties including all warranties of merchantability and or fitness for a particular purpose As some states do not allow exclusions or limitations on an implied warranty the above exclusions and limitations may not apply This warranty gives you specific legal rights and you may have other rights that vary from state to state This warranty is limited to the replacement of defective parts only Labor charges and or damage incurred during installation repair replacement as well as incidental and consequential damages connected with the above are excluded Any damage to this product as a result of neglect misuse accident improper installation or use other than the purpose SHALL VOID THIS WARRANTY Pre Operation PLANNING FOR SUCCESSFUL INSTALLATION Place your fountain on a level surface away from areas where it is likely to get clogged with leaves or other debris and make sure that the electrical cord reaches the power outlet This fountain is designed to operate as splash free as possible However some water splashing out of the fountain is inevitable Place your fountain in a location where any splashing will not cause damage Keep the fountain full of water and clean of debris and dirt to ensure proper functioning of the pump PACKAGE CONTENTS B Part Description Fountain b
4. ged in Regularly check that the water reservoir has enough water to cover the pump at all times Check the water level more frequently in warm or windy weather Do not allow the pump to freeze During cold spells remove the pump from the fountain and place it in a water filled container in a frost free location DO NOT store the pump dry Care amp Cleaning the fountain causes the water to foam and should be avoided unless Disconnect the power before you service or clean j NOTE You can use a mild detergent but note that this strictly necessary At minimum rinse the pump out with lukewarm water when the pump s power starts to drop NOTE Do not use any abrasives which can damage the applied finish Periodically change the water and clean the outside of the fountain and the reservoir The frequency of this will depend on the weather and location of the fountain Due to water evaporation you may see a buildup of white residue on the fountain surface from mineral content in the water supply Use a soft cloth and clean water to clean the outside of the fountain Use a soft brush to clean the reservoir Clean the pump rotor approximately once a month A good indication that the rotor needs to be cleaned is if the water flow rate drops To clean the rotor and associated parts 1 Switch off and unplug the pump 2 Remove the pump f
5. na 5 Maintenance eseas tennis nda 6 Care amp Cleaning s ccsseecseeeeseneeseeeseneeseneeneneenenensenens 6 TES A 7 SpecificatioNS ococconiosniaciracinainienne cenar 7 gt CAUTION This product is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have supervision or instruction concerning the use of the appliance by a person responsible for their safety CAUTION Do not use the pump in vehicles on board ships or in an aircraft CAUTION Make sure that the pump is assembled and fully immersed in water before you plug the fountain into the power source CAUTION The pump must be supplied through a residual current device RCD with a rated residual operating current that not exceed 30mA CAUTION Do not use the appliance in a swimming pool IMPORTANT Do not use the pump for industrial purposes IMPORTANT Keep the plug dry Do not expose the plug to water or steam 0 e ebp IMPORTANT The appliance is not intended for use by young children without adult supervision Warranty If this product fails due to a defect in materials or workmanship at any time during the first one year of ownership the manufacturer will replace it free of charge postage paid at their option This warranty does not cover products which have been abused altered damage
6. ody Transformer plug Pump olojo gt LED light Assembly 3 Connecting hose to pump outlet Connect the flexible hose E to the pump outlet F Make sure the connection is tight Place the pump C in the bottom of the reservoir TNT ON Connecting the cords Connect the pump cord G to the transformer B base Connect the LED light cord D to the transformer cord branch H Filling the reservoir Use clear and clean water Make sure the water can completely submerge the pump The reservoir should be 75 full at minimum The pump will not work if it is not completely submerged at all times Operation 1 Turning on the pump 2 Adjusting the pump flow rate Plug the electrical cord into a power outlet and Move the flow control slider H towards the to switch the pump on increase the flow rate and move the slider towards After a few moments the water starts to flow the to decrease the flow rate ar NOTE You must use a GECI outlet NOTE Splashing can occur if the flow rate is too high or the reservoir is too full Maintenance the fountain water and never be permitted to run dry as this will cause irreversible damage Disconnect the power before you service or clean CAUTION The pump must always be fully submer
7. rom the water reservoir and disconnect the flexible hose from the pump outlet F 3 Remove the filtering cover H and pressure casing 1 from the front of the pump body 4 Clean the rotor J and housing K in clean water using cotton balls 5 Reassemble the pump reconnect the flexible hose to the pump outlet F and place the pump back into the reservoir Troubleshooting CAUTION Running the pump without enough water can damage the pump CAUTION Excessive weight or pressure on any of the fountain sections may cause it to fall Keep pets children or anyone from sitting leaning or climbing on any of the fountain components Problem The pump will not run Cause Corrective Action Faulty circuit breaker Check the circuit breaker Faulty outlet Try another GFCI outlet Not enough water in the fountain Check the water level in the fountain Flow control is low Check the setting on the pump s flow control Pump is clogged Check the pump discharge and intake for dirt and debris Fountain is clogged Pump is air locked Check the fountain tubing for kinks and obstructions Plug and unplug the pump several times Specifications MZ20450AB PUMP Model No MZ20450AB Operating Voltage 12V Frequency 60 HZ Current 0 9A Maximum lamp 1 0W Power consumption Watts 7 0 W Delivery head 3 28 ft 1 0 m Delivery 45
Download Pdf Manuals
Related Search