Intec 50013-00 Installation Guide
Contents
1. by the manufacturer 5 Use of Extension and Power Cord a This product requires the use of a power cord In addition to the supplied power cord care should be exercised in the selection and use of an extension cord b The extension cord shall be a grounded 3 wire cord c The extension cord should be arranged so that it will not drape over the countertop or tabletop where it can be tripped over snagged or pulled on unintentionally especially by children d An outdoor rated extension cord should be used with this machine An outdoor use extension cord is marked with suffix letter W and with a tag stating Suitable for Use with Outdoor Appliances e The marked electrical rating of the extension cord shall be rated for at least 15 amps f To unplug or disconnect Put the blower and agitator control panel and remote buttons in the stop position before removing plug from outlet Do not unplug by pulling on the power cord To unplug grasp the male and female plugs and pull apart Unplug from outlet when not in use and before servicing or cleaning i Do not operate any insulation blower with a damaged cord or plug or after the machine malfunctions or is dropped or damaged in any manner e 6 In the case of a non operable or malfunctioning blower return the insulation blower to the nearest authorized service facility for examination repair or electrical or mechanical adjustment 7 Store insulation blowe2. Operation and Safety Guide Model s 50004 00 amp 50013 00 FIBER rona Vendor Website www inteccorp com Support Phone No 800 666 161 1 See operational video at http www inteccorp com fiberforce Tool Operation SAFETY TOPICS Action Lise eae a ama aati u Unload machine using safe lifting techniques Secure hopper base with TP y ougn y I the four fasteners Note Match key slot in base to that of hopper for understand the operator s manual Please visit i tg ii Positi hingi dwt df http www inteccorp com fiberforce for additional ital aii sega el ul cea coo nad iar A E eae gaan ait niommnaton environment to allow for suitable material feed and electrical power access Sweep hand across the filter to clean any foreign materials Ensure that all panel switches are in the off position Using the twist lock power cord supplied plug the machine into a dedicated 115V 15amp or 20amp circuit Install the 2 50 2 1 2 hose sections The section with the male amp female adaptor goes on the machine first The other section with the remote plugs into the first hose Ensure that the retainer snaps into place to prevent hose blow off SA 3 SAFETY CHECKLIST 1 Read all the instructions before using the insulation blower 2 To reduce the risk of injury close supervision is necessary when an insulation blower is used near children 3 Do not contact moving parts 4 Only use attachments recommended or sold
3. n expand into hopper Cellulose Remove packaging Place cellulose bale into hopper Hose operator takes the hose to the location for insulation blowing Use the remote to turn machine on to blow insulation material Hopper Operator continues to feed material into hopper until job is complete WARNING 1 Never reach into the hopper when system is operating 2 Keep all foreign materials out of hopper 3 Stop all motors and disconnect power cord before attempting to remove a foreign object or jam 4 Never point insulation hose in direction of people or pets a B 3 At completion use the remote or panel switch to turn machine off Remove any insulation still in the system Return machine two hose sections and power cord to the rental center
4. r indoors when not in use Keep out of the reach of children 8 Never operate this equipment if the operator or the machine is standing in water snow or rain Do not clean this insulation blower with water spray or the like 9 Connect to a properly grounded outlet only 10 Wear long sleeve shirt gloves a hat safety glasses or goggles and a nose amp mouth dust mask Beni a 4 Open the material feed gate by removing the locking pin Attics pull slide gate outward to the last hole position and secure gate by placing pin in the last hole Walls Refer to the owner s manual or Intec s website for proper settings Ensure the GFCI is reset reset the agitator circuit breaker amp turn on the main circuit breaker The white ready light on the side of the machine will illuminate Note if the white light does not come on ensure that the hopper is properly positioned with the opening above the circuit breakers g h oe PN Undo the strap securing the hopper door loading platform Lift up on the door slightly and pull forward into the loading position Directions for loading the machine are printed on the loading platform Caution Never let the plastic packaging enter the hopper Caution Never push down on insulation when in hopper Fiberglass Cut bag of insulation in half Place open end of 2 bag to the left or right side of the loading platform Slice plastic with cutting tool and let insulatio
Download Pdf Manuals
Related Search