HICKOK 45665 Use and Care Manual
Contents
1. MAX MIN DELAY ENTRY Displays the delay values for the engine selected To manually set Max Min Delay use the up down arrows to change the values and then select ENTER FLYWHEEL U Wain iy Eey Oil Pressure Monitor Cylinder Kill and Fuel System DTC Monitor Procedures Hookup Procedure for Ford Engines Hookup Procedure for International Engines To connect to the vehicle To connect to the vehicle 1 Remove the cover from the vehicle s wv 1 Connect the vehicle interface OBD II connector if applicable included in kit cable VDA to the vehicle per normal procedures RP 1210 Compliant Data Link Adapter user supplied Vehicle Interface Cable 2 Connect the Vehicle Interface Cable to the vehicle s OBD II connector To connect to the computer 1 Connect to the vehicle as To connect to the computer P described in the steps above 1 Connect to the vehicle as described in the steps above Connect to the 2 Plug the USB connector into computer s USB port Connect tothe vehicle s OBD II the computer s USB port 2 Plug the USB connector into the computers eOnReCIO computer s USB port USB port G2 is compatible with the these adapters e Dearborn Group IC4 NAVCOoM N ink Connect to the Test Procedures for International and Ford Engines Connect your computer to the vehicle per the hookup procedure Start the vehicle Open the G2 Injector Di2. Engine Torque Rate Navistar vehicles Displays the fuel rate deviation for each cylinder ELAPSED TIME Displayed in real time shows the elapsed time since Abort Test the test began once it beg Ford vehiq A TOOL BAR STOP Select to stop test Note The button is grayed out if the function is not available 0 09 nj nj_4 PRINT SCREEN nj ni 167 Deg F CLEAR Select to clear the current values Available after stopping a test ACQUIRE DATA Select to begin the test EXIT Select to exit and close the program Available after stopping the test FUE RATEg h FUEL RATE DEVIATION ENGINE LOAD ENGINE LOAD DEVIATIO Fuel System DTC Monitor Hickok Diesel Diagnostic Suite Beta v1 01 DTC Monitor Window Displays information regarding the found system related DTCs or Beta Sie ER CAO NG TiS COMER DTC Num PID SID Code Status Description 428 Subitem ZZY Engine Load Displays the engine load deviation for each cylinder Engine Oil Temperature Displays current engine oil temperature RED Not at optimum temperature for accurate test results GREEN Optimum temperature for accurate test results reached Numerical Data Displays the various results for each cylinder SCAN FOR DTCs Select to check for and display any fuel system related DTCs RALIN 19120 995 For Technical Sup
3. on the graph with the same color as the square FLYWHEEL boas ppo a aa a ftp TT Max Min Delay Entry 4 45 40 47 40 4 48 40 ELAPSED TIME Seconds NTEF ACQUIRE CLEAR ADJUST RPM ENTER COMMENTS HERE B50 Note The butt zl DAIA ii EE ANCEI TOOL BAR the function is PRINT SCREEN EXIT q G2 Tester UE a 100 begin the test STATUS BAR Displays the COM port the CLEAR DATA Select to clear tester is connected to the current values Available after stopping a test PRINT SCREEN Select to i ADJUST RPM printout and save a picture ADJUST RPM Right Circle When green the engine is J of the current window If a printer is not available a jpg file is still saved on the computer s hard drive ADJUST RPM Left Circle When red the engine operating conditions will not allow the tester to take measurements Manually EXIT Select to exit and close the program Available after stopping the test and the right circle turns green operating within acceptable conditions adjust the vehicle s RPM until the circle turns black Hiro HICKOK VEE Se a EE INCORPORATED surrounding the cylinder number 4 ad a FLYWHEEL 4 48 40 ENTER COMMENTS HERE Using the computer s keyboard enter desired comments such as the customer s name vehicle information etc before printing and or saving a screen shot
4. G2 Injector Diesel Diagnostic Suite Quick Reference Guide For International and Ford PowerStroke Diesel Engines IMPORTANT Please make sure to carefully read these instructions before you begin to use the tester G2 Injector Test Procedure for International and Ford Engines Without the PC Application iP Connect G2 to the vehicle G2 Injector Test Hookup Procedure for International and Ford Engines Serial Port Cable 2 Start the vehicle ly oe IDM Tee USB to Serial 3 When prompted select the vehicle s engine Adapter Cable Port Adapter 4 This end to 5 Select the type of sampling both display numbers in actual time Single Capture Takes one sampling Continuous Capture Continues to take display samples until you stop the test Review the results for each cylinder by pressing SCROLL With the PC Application 1 Connect G2 to your computer UU A W N O Top LCD Screen displays instructions and test results em Bort Navigation Buttons the function of the 9 Pin Port buttons are displayed on the screen such as selecting a function SEL or a vehicle s engin scrolling through results or moving to the LCD er Navigation LED lights when the tester is powered o View Buttons 9 Pin Port connect the Serial Port C a Connecithe sea LED this port Connect G2 to the vehicle Start the vehicle and when prompted on the G2 select the vehicle s engine Open t
5. esel Diagnostic Suite on your computer Connect your computer to the ookup procedure Start the vehicle Open the G2 Inject ite on your compute e W N gt When prompted sel and available adapter anufacturer enginetype gt W N gt When prompted select the vehicle s manufacturer engine type and available adapter G2 Injector Diesel Diagnostic Suite 1 03 Beta 5 VI At the Main menu select the desired test 6 At the G2 Injector Test screen select Acquire or Begin Test depending on test selected to begin displaying the results on the computer in real time Er n fo r m at j O n S e e ct i O n S c re e n Select Vehicle Engine Type amp COMLink Adapter E F y LES i ry y i f 2 This screen is displayed when you start the a2 Porat i sell G2 Injector Diesel Diagnostic Suite el 1 AP 1eselr Diagma at Suite Select the information for the vehicle you k are testing and then select SUBMIT to I l 1 proceed to the Main menu To clear the information and reselect the vehicle information select RESET Please Select S See other side for information on the G2 Injecto l v Oil Pressure Monitor Cylinder Kill Test This test automatically kills each cylindgg to determine if are any AER changes in the fuel rate and engine lo detect a weak cylinder Exit ge of PSI Values for the current test Fuel Rate
6. he G2 Injector Diesel Diagnostic Suite on your computer When prompted on your computer select the vehicle s manufacturer engine type and available adapter At the Main menu select G2 Injector Tester At the G2 Injector Test screen select Acquire Data to begin displaying the results on the computer in real time Using the G2 Controls POWER 24 Pin Port connect the A Cable to this port G2 Injecto tor Tester Beta V1 00 SPOOL DELAY VALUES Range of Spool Delay Values for the current test ster Ank the computer IDM Tee Adapter This side to injector harnesses Only required CPU when connecting gt a computer om the IDM PC This side to vehicle s IDM To connect to the vehicle In the engine compartment 1 Disconnect the vehicle harness FICM depending on vehicle 2 Connect the Tee ad and secure it using at A WARNING ation on the Oil Pressure Monitor d fuel System DTC Monitor Procedures See oth Cyli ication Overview DER Injector Status FAN INJECTOR STATUS Displays the engine cylinder layout and the individual test results for each te a injector including the spool delay values Green indicates a PASS red indicates a FAIL for that particular injector The cylinder is ar lt gt r mo identified
7. port 1 800 342 5080 aya on iCKOK 2010 Hickok Inc All rights reserved Printed in the United States ay INCORPORATED
Download Pdf Manuals
Related Search