Home
Speakman SEF-2001-8 Installation Guide
Contents
1. Turn on HOT and COLD handles of Faucet and allow water to run for one minute to flush any debris from Faucet Install the Aerator with the supplied Aerator Wrench SPEAKMAN 05 1899 The spout was designed to swivel from left right If a non swivel Spout is preferred remove Top Cover from Body Remove allen head Set Screw from position 1 as seen below Center the Spout between the handles and install the previously removed Set Screw into position 2 and tighten DO NOT OVERTIGHTEN Replace Cap Eyewash Flow Data a E y 7 a eg 5 2001 SEF 200 1 8 FLOWING PLUME PRESSURE FLOWRATE DISTANCE A NOTE If plume heights are low check to ensure that your Supply Valves are fully open If there is a noticeable height difference between the two plumes remove the Aerators and Flow Controls and remove any debris that would inhibit the flow of water ROUGH IN MEASUREMENTS FRONT VIEW SEF 2001 SIDE VIEW LESS HOSES 5 1 2 41 2 47 8 6 MIN FROM WALL OR OBSTRUCTION a 4 1 2 o2 1 4 1 3 8 HOLES 2 AS 1 1 4 MINIMUM HOLE SIZE 1 2 COMPRESSION INLET
2. sim 2 1 4 19 2001 2 MAX DECK HEIGHT 17 SEF 200 1 8 SPOUT SUPPLY EYEWASH HOSE 2 HOSES HOSE 24 MIN 36 MAX COLD SUPPLY COUNTERTOP HEIGHT SUPPLY Z 7 1 2 6 LONG HOSE 6 7 8 7 TEE WITH CHECK 6 MIN FROM WALL TEE WITHOUT 2 MAX DECK HEIGHT SEF 2001 8 SIDE VIEW LESS HOSES VALVES OR OBSTRUCTION CHECK VALVES REPAIR PARTS G05 0872 PC 1 5 GPM FAUCET AERATOR RPGO5 0908 EYEWASH AERATORS FLOW CONTROL ADAPTERS ADAPTER WASHERS AND FLOW CONTROLS RPGO4 0409 EYEWASH HANDLE WITH YELLOW TEXT AND SET SCREW UPPER EYEWASH COVER WITH FLIP CAPS EYEWASH CARTRIDGE Se E OTC MEA NOTE UNLESS OTHERWISE SPECIFIED ALL INLETS ARE 3 8 COMPRESSION WITH FEMALE THREADS UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES AND ARE SUBJECT TO CHANGE WITHOUT NOTICE g2 1 4
3. Nut 1 mounting hardware and then remove Spout from counter top Using a Tube Cutter cut the copper tubing between each End Body and the Tee Assembly Remove and discard remaining copper tube and Capture Nuts from End Bodies Remove COLD supply line from wall stop and COLD End Body O With Spout fully removed verify diameter of hole in counter top is a minimum of 1 1 4 Install mounting studs into base of Spout Install Bottom Washer over hoses and slide up to meet the base of the Spout Place hoses through hole in countertop sink one at a time Lower Spout Assembly through hole From beneath countertop install Rubber Mounting Washer 1 Brass Mounting Washer 2 and Brass Mounting Nuts 3 Align Spout square to sink and tighten Mounting Nuts 3 Retrieve the 6 long hose with a BLUE stripe from the box and connect one end to the COLD supply valve Wrench tighten 7 Locate the Supply Tee with check valves installed Connect remaining 9 Retrieve supplied hose with a 3 8 fitting on end 1 2 end of hose to the port with no markings Wrench tighten fitting on the other Connect 3 8 fitting end to the F port of the Tee with check valves Wrench tighten Locate the hose labeled EYEWASH that is pre installed in the base of Connect the remaining end of the hose with 1 2 fitting to the the
4. Instructions for Models SEF 200 1 SEF 200 1 8 EYESAVER Combination Faucet Spout Need Help For additional assistance or service call SPEAKMAN Company 400 Anchor Mill Road New Castle DE 19720 PHONE 800 537 2107 EMAIL customerservice speakmancompany com WEB www speakmancompany com 92 SEF 2001 R1 What You Need To Know Tools Required Tube Crescent Cutter Wrench Basin Flat Head Wrench Screwdriver Important Notes The supply line for this unit shall provide an uninterruptible supply of flushing fluid at a minimum of 30 psi flowing pressure If shut off valves are installed in the supply line of the eyewash provisions shall be made to prevent unauthorized shut off ANSI Z358 1 requires that all emergency equipment shall be tested weekly to verify proper operation and inspected annually to assure conformance with ANSI Z358 1 requirements Be sure to read instructions thoroughly before beginning installation Do not overtighten any connections or damage may occur Safety Tips Cover your drain to prevent loss of parts Always wear eye protection Maintenance Keep the EYESAVER faucet spout looking new by cleaning it periodically with a soft cloth Avoid abrasive cleaners steel wool and harsh chemicals as these will dull the finish and void your warranty Turn off water supplies Loosen and screw down Spout Shank Nut 1 Unscrew Tee Nut 2 from Spout Shank Remove Shank
5. SEF 2001 Connect this hose to the E port of the Tee with check bottom port of the COLD End Body Wrench tighten valves Wrench tighten AD Retrieve the Supply Tee with no check valves Connect the F port of 13 ees the Supply Tee to the remaining hose pre installed in the base of the SEF 2001 Wrench tighten 3 8 port of the COLD End Body Wrench tighten LL m Retrieve the two 2 remaining supplied hoses Take the first hose and 4 NOTE Before testing you must remove tape from Eyewash Caps connect one end to the E port of the Supply Tee with no check Turn on water supplies and check for leaks Activate Eyewash by valves Connect the remaining end to the 3 8 port of the HOT End lifting activation handle and check for proper function using the Body Wrench tighten chart at the the end of this document gt gt gt 7 F WV r P lity Jra fy
Download Pdf Manuals
Related Search
Related Contents
UE403 switching amplifier USER MANUAL - CAMBOARD Electronics manual do usuário ULVAC油拡散ポンプ VPC250F GE Monogram ZSC2200 Oven User Manual Advance 25 User Guide Learning Hub User Guide Managed 19” Rack-mount 18-Slot Card Impressora a Laser Xerox Phaser ™ 5400 Guia do Usuário Copyright © All rights reserved.
Failed to retrieve file