LockState LS900 Instructions / Assembly
Contents
1. FOR OTHER DOOR THICKNESS TEAR OFF AT COTTED LINE 158mm 16mm DIA BOTHISIDES Lu Z Y une Eu Z site 218 p 9 CYLINDER gt HOLE 52 1 DEPENDS ON THE TYPE OF LOCK CASE USED Enn ES dn 1 2 DEPENDS ON THE TYPE OF l KEY CYLINDER USED FOLDING LINE AT THE EDGE OF THE DOOR Dr 23 ER aS eee 2 oe SC j Q11 5mm l FOR OTHER DOOR THICKNESS TEAR OFF AT COTTED LINE AND PLACE ON CENTER LINE OF DOOR EDGE 2 158mm 16mm DIA BOTH SIDES m 9 A m g TI 3NITH2 LN3O IVOLLHSA CYLINDER k HOLE 57 51 DEPENDS ON THE TYPE OF LOCK CASE USED 2 DEPENDS ON THE TYPE OF F KEY CYLINDER USED VERTICALCENTERLINEOFBACKSET gt FOLDING LINE AT I THE EDGE OF THE DOOR2. PARTS LIST INSTALLATION AND GENERAL INFORMATION PARTS LIST ACCESSORIES PACK 2 ACCESSORIES PACK 1 make sure you have received the following gt Escutcheons e 2spindles 8mm square and 7mm square 4 Screws 1 spindle collar 1 Outside lock mechanism 1lock pin for locking the collar and the 2 Inside lock mechanism spindle together 3 Accessories 4 packs 2 91 Long amp ashor F hexagonal screwed posts are already fitted gt to back of outside lock mechanism Eii ACCESSORIES PACK 3 e 2non codedtumblers 2 4 36 screws 1long hexagonal shaft 2coded tumblers e 2 M4X51 screws 1 hexagonal key 1Tweezer x2 x2 INSTALLATION 1 ESTABLISH THE HAND OF THE DOOR Viewing from OUTSIDE it is right hand if the hinges are fitted on the right and it is left hand if the hinges are fitted on the left hand side of the door This is regardless of whether the door swings inward or outward 2 INSTALLATION APPLY THE TEMPLATE Tape the template to the door Make sure that you fold it along the aooropriate line depending on the backset of the latch 60mm Or 70mm Mark and drill all six 10mm holes Use a chisel to clear the line of 4 x 10mm holes into a single slot POSITIONING AND FIXING THE LATCH Mark a central point on the centre line of latch on the door edge Drill a 28mm hole x 88mm deep Insert the latch into the hole and draw aro
3. With the back of the outside door mechanism facing you a Turn the spindle counter clockwise fully diag 4 b Slide the spindle through the follower of the lock case IF REMOVING THE GRUB SCREW FOR ADJUSTMENT OR TO REVERSE THE HAND PLEASE ENSURE IT IS REPLACED AND TIGHTENED UP FULL INSIDE DOOR MECHANISM diag 5 With the back of the inside lock mechanism facing you a Unscrew the 4 screws marked b Swing the handie to the other side C Tighten the 4 screws back into the original position HANDING Rules The hand of a door is always determined from the outside 2 The outside of an exterior door is the street or entrance side 3 The outside of an auditorium door is the corridor or hall side 4 The outside of a room door is the corridor or hall side 5 6 The outside of a closet door is the room corridor or hall side The outside of a single communicating door is the side from which the butts are invisible when door is closed 7 The outside of twin communicating doors is the space between the two doors For Right Hand Door SPINDLE rA For Left Hand Door SPINDLE SCREWS diag 5 HANDING CHART Always take hand from ourside Hand of door Hand of door right hand RH left hand LH Hand of door Hand of door right hand reverse left hand reverse RH LHR GENERAL INFORMATION CHANGING THE ACCESS CODE Your lock has been pre programmed with a four digit access code This se
4. closing the door 21 square cut out side out side TUMBLER E BLUE KEYLESS ks cut TUMBLER push button fl RED COLOR gi BLUE COLOR SUPPLEMENTARY INSTRUCTIONS FOR 900 SERIES LEFT HAND DOOR Outside Lock Mechanism a Remove the rubber cover 1 at the side of the handle b With the hexagonal key provided loosen the grub screw 2 at the side of the handle until the handle can be removed c Slide the handle out from the holder and refit the handle to the left side d Tightened the grub screw e Replace the rubber cover MOL IE ud Rubber cover Grub screw Handle Handle holder Outside Lock Mechanism Warning In some situation The operation ofthe handle will become sluggish when it has been removed and refitted When this occurs operate handle continuously by engaging the F function until the handle returns to its original position smoothly D Fold along the edge of the door Match to length of LATCH 70mm 60mm Centre line of latch Outline of rubber seal 8mm Hole Outline of Lockcase Drill 4 holes and clear a slot through the door 8 mm Hole seal TEMPLATES 8 mm Hole Outline Outline of of rubber Lockcase Drill 4 holes and clear a slot through the door 8mm Hole Fold along the edge of the door Match to length of LATCH 60mm 70mm
5. ction tells you how this code may be changed You will also have been supplied with spare tumblers these may be used to reduce the code to five digits Also supplied is a pair of tweezers for removing the tumblers Make sure these are ready to hand 1 Remove the main body of the lock from the door 2 Place the lock body face down on a firm flat surface and remove the fours screws securing the back plate Take care at this stage as there are many small parts that might become loose 3 Removing the back plate will reveal lock tumblers in two columns of Six 4 red 6 blue one F button and one C Red tumblers relate to the code blue tumblers are nul The clear tumbler is activated by the C button the free access is activated by the F button AND SHOULD NEVER BE REMOVED 4 Tumblers are freed by pressing the C button when they may be withdrawn using the tweezers provided Transposing red and blue tumblers in the lock will change the existing five digit code exchanging red and blue tumblers from the spares provided will alter the number of digits used in the code PLEASE NOTE that tumblers must be correctly positioned according to the column in which they are placed See drawing below 5 When you have completed your changes make a note of the new code 6 Reassemble back plate satisfy yourself that the new code operates as expected 7 Re fit lock to door Once again test the new code before
6. und the face plate Remove the latch and cut a 3mm rebate so that the face plate will fit flush with the door Secure the latch with the wood screws 3 BEFORE FIXING Please check that the LS 900 series is working correctly by entering the code remembering to press the C button first 4 FREE ACCESS FEATURE To activate the free access feature follow the procedure A enter the correct code B press the F button C press the handle down fully to open the door To de activate the free access feature A press the F button B press the C button fully down SPINDLE ASSEMBLY diag 1 a Choose the correct size spindle according to the size of the follower of the lock case b Slide the spindle collar onto the rounded end of the spindle and lock it in place with the lock pin provided SPINDLE COLLAR INSTALLING THE SPINDLE ASSEMBLY INTO THE OUTSIDE LOCK MECHANISM diag 2 With the back of the outside lock assembly facing you a Unscrew the 2 screws A and B b Remove the cover C c Place the spindle assembly into the slot under cover C d Replace cover C Secure cover C with screws A and B CHANGING THE HAND OF THE LOCK RIGHT HAND DOOR diag 3 The lock is pre set for Right hand door With the back of the outside door mechanism facing you Turn the spindle clockwise fully b Slide the spindle through the follower of the lock case LEFT HAND DOOR OUTSIDE LOCK MECHANISM diag 4
Download Pdf Manuals
Related Search