Cadet FWAP Installation Guide
Contents
1. and remove top and bottom grill screws to remove grill 2 Remove screw on bottom center of heater assembly 3 Unscrew insulated wire connectors and separate supply wires from heater wires 4 Remove the heater assembly by pushing up in the direction of the fan and pulling unit out of wall can Installing Conversion Kit 1 Screw top and bottom screws and washers about halfway into the wall can with the half moon tabs facing out See Figure 1 2 Push plate down into position 3 Tighten the screws NOTE Star washers MUST be located between the screw head and painted surface of the conversion plate 4 Install one spring nut at the top and one at the bottom See Figure 2 Installing New Heater Assembly Note If FW heater was wired with the supply circuit entering the wall can from the top it may be necessary to add 8 inches of lead wire to each of the supply lines before proceeding with installation of new heater 1 The Com Pak requires a thermostat to operate Please follow wiring instructions supplied with either your built in thermostat kit or wall mount thermostat and your new heater If new heater has a built in thermostat the two mounting screws must be removed and reattached to the bottom of the FWAP 2 Once wiring is complete slide heater assembly into half moon tabs located on bottom of conversion plate Use screw supplied with heater assembly and star washer supplied with kit to attach heater to conversion plate2. 3 If using original grill turn the grill upside down See Figure 3 and install using two new 10 screws If there is a built in thermostat be sure it is at the bottom 4 Affix new label provided on inverted grill It is not necessary to remove the old label If using a built in thermostat cut thermostat shaft hole out of new label Operation Instructions 1 Once installation is complete and power has been restored turn the thermostat knob fully clockwise 2 When the room reaches your comfort level turn the thermostat knob counterclockwise until the heater turns off The heater will automatically cycle around this preset temperature 3 To reduce the room temperature turn the knob counterclockwise To increase the room temperature turn the knob clockwise Figure 1 Figure 2 Spring Nut l Spring Nut Figure 3 2014 Cadet Printed in U S A 12 14 720027
3. FWAP Conversion Kit Installation Instructions http www cadetheat com products wall heaters com pak Features amp Benefits Converts discontinued FW Series wall can to newer Com Pak or Com Pak Max UL Listed for installation of Com Pak model into FW wall can No sheetrock construction necessary saves time and money Vertical or horizontal installation PARTS INCLUDED TOOLS REQUIRED 3 Screws Phillips Screwdriver 2 Spring Nuts Straight Screwdriver 2 Lead Wires 1 Replacement Grill Label 2 Mounting Screws 1 Conversion Plate 3 Lock Tooth Washers vertical installation shown 1 Instruction Guide Model FWAP to be used with any CS model heater Any of the following models may be replaced using the FW conversion kit FW051 RW051 FW052 RW052 FW071 RW071 FW751 RW071 FW752 RW752 FW072 RW072 FW101 RW101 FW102 RW102 FW121 RW121 FW122 RW122 FW151 RW151 FW152 RW152 FW202 RW202 FW252 RW252 FW302 RW302 The above models may be controlled by either a built in thermostat or a wall mount thermostat General Safety Information If you are uncomfortable working with electrical appliances unable to follow these guidelines or do not have the necessary equipment consult a licensed electrician A home which could result in a fire and serious property damage AN WARNING Replacing with a lower wattage heater may cause insufficient Turn the electrical power off at the heat and res
4. ult in increased energy costs electrical panel board circuit rei or _ nox Da lock to All electrical work and materials must comply with the National ag 8 pane Doar Qor tO Electric Code NEC the Occupational Safety and Health Act prevent someone from turning on OSHA and all state and local codes power while you are working on the heater Failure to do so could N is result in serious electrical Shock When installing the heater conversion kit be certain the FW burns ar osii death z heater being replaced was wired correctly to all electrical codes f ON Poss i and the supply wiring is the correct size and in good condition 1 WARNING If not it must be replaced before proceeding Risk of fire or property damage DO NOT replace your heater with a higher wattage assembly Replace your heater with the same voltage and wattage that was originally installed Replacing it with a higher wattage 5 heater could result in an overloaded electrical circuit in your A If you need to install a new circuit or need additional wiring information consult a qualified electrician Protect electrical supply from kinks sharp objects oil grease hot surfaces or chemicals SAVE THESE INSTRUCTIONS cadetheat com Tel 360 693 2505 P O Box 1675 Vancouver WA 98668 1675 2014 Cadet Printed in U S A 12 14 720027 FWAP Instructions Back Side Removing Old FW Heater 1 Pull off thermostat knob if applicable
Download Pdf Manuals
Related Search