Barclay Products TKCTR60-CP1 Installation Guide
Contents
1. A o Code Rectangular Cat No GY Shower Unit 4122 4124 Barclay lor sonin spec INSTALLATION INSTRUCTIONS Parts Included e 1 Valve Body 1 Hose 1 Cradle 4 Washers e 2 Cone Washers 2 Large Locknuts 2 Connecting Nuts e 2 2 1 4 Threaded Nipples Tools Needed e Adjustable Wrench Slip Joint Pliers Pipe Putty or Teflon Pipe Tape 2 Mounting Flanges Needed NOT included NOTE Handles are identified HOT and COLD The hot handle must be to the left and cold to the right Be sure the water supply is turned off before starting installation Cushion the wrench or slip joint pliers with an old cloth to protect the finish of the fixture Shower Assembly amp Tub Mount Instructions 1 Turn off the water supply 2 Align the valve assembly with the mounting flanges and secure with the nuts on the mounting flanges Rubber washer must be in place Tighten with a wrench Note Flanges may be positioned up or down depending how high you would like the spout placed and the hole spacing 3 Apply teflon tape to both ends of the hot and cold supply nipples Thread the tapered ends of the nipples into the mounting flanges on the outside of the tub Thread the large locknuts and metal washers onto the other ends of the nipples and secure the shower set to the tub 4 Install a washer in the cradle nut and thread the cradle onto the valve assembly Tighten with a wrench 5 Install washers on the hos2. e copper plumbing in your home 1 8 08 P 847 244 1234 www barclayproducts com
3. e ends and attach the hose to the cradle and shower head DO NOT OVERTIGHTEN To Connect Shower Set to Tubes 1 First remove the round rubber washer from the end of each water supply tube and dispose of them 2 Put the cone washers on the tub and connect the end of each water supply tube Then slide the 1 2 connecting nuts over the opposite ends of the supply tubes and up to the cone washers 3 Twist the connecting nuts over the cone washers and thread the nuts onto the nipples 4 Connect the other ends of the water supply tubes to your house water lines Consult your local plumber for assistance NOTE Please seek professional help if you have copper plumbing in your home Cleaning Instructions Wipe this whole set off with warm water and a soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the protective lacquer coating and leave the brass exposed causing it to tarnish Pg 1 4 14 09 P 847 244 1234 www barclayproducts com 4 Water Supply Hookup Kit Cat N p ater Supply up Ki at No q for Tub with Legs 5576 ATCAY INSTALLATION INSTRUCTIONS Parts Included e 4 Cone Washers A 2 Decorative Locknuts B Left Supply Tube C e Right Supply Tube D 2 Escutcheons E 2 Locknuts F Tools Needed e Adjustable Wrench Set of Crescent Wrenches Pliers Teflon Tape use as a sealant on all male threaded tubing This water supply tube kit includes the parts listed abo
4. ve ONLY The faucet in your bathtub should be purchased previously and separate from this kit To Assemble Tubes 1 First be sure to shut off the the water supply Remove old water supply tubing Put a cone washer A with the wide end of the washer inward onto the upper end of the left supply tube C 2 Slide a decorative locknut B up to the top of the left supply tube C and put on a cone washer A 3 On the bottom of the left supply tube C slide one of the escutcheons E up the tube partway then slide the locknut F up the end of the tube C directly under the escutcheon 4 Put another cone washer A with the wide end of the washer upward onto the bottom end of the tube C 5 Repeat steps 1 4 using the right supply tube D To Install Tubes 1 Attach the bottom end of the left supply tube C to the water supply tubing in your floor by screwing the locknut F down tightly Let the escutcheon E slide down to the floor 2 Attach the upper end of the left supply tube C to the cold side faucet supply tube located on the rear of your tub by inserting the supply tube C into the faucet supply tube and tightly screw the decorative locknut B over the two for a tight fit 3 Repeat steps 1 2 using the right supply tube D and connecting it to the hot side faucet supply tube NOTE Please seek professional help if you have copper plumbing in your home Cleaning Instructions Wipe this whole set off
5. with warm water and a soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the protective lacquer coating and leave the brass exposed causing it to tarnish 10 30 07 P 847 244 1234 www barclayproducts com E Leg Tub Cat No Barclay D rai n 5599 for something sperial INSTALLATION INSTRUCTIONS Parts Included e Top Overflow Tube 1 Bottom Shoe 2 Top Waste Flange 3 Face Plate 4 Exposed Tee 5 e Face Sponge Gasket 6 e Waste Gasket 7 Lift Stop 8 2 1 1 2 Nut and Washers 9 Face Plate Screw 10 1 1 2 x 6 Tube 11 1 1 2 O D Escutcheon 12 Tools Needed e Wrench e Pliers Teflon Tape use as a sealant on all male threaded tubing Tube Cutter Plumbers Putty To Assemble Tubes 1 Assemble 3 and 8 screw into 2 7 is on top of 2 beneath the tub Place a bead of plumbers putty around bottom of 3 to seal to tub and protect from leaks Then tighten 3 into 2 2 Assemble overflow Follow diagram 3 Set 1 in place 4 Place Tee 5 on shoe Cleaning Instructions 5 Trim bottom of tube 1 to fit into Tee 5 Wipe this whole set off with warm water and a 6 Trim tube 11 to fit soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the 7 Tighten the nuts protective lacquer coating and leave the brass exposed causing it to tarnish NOTE Please seek professional help if you hav
Download Pdf Manuals
Related Search