Coastal Shower Doors P2020.70G-C Instructions / Assembly
Contents
1. Using a 3 16 masonry bit drill 1 deep s TRACK S HIGH LIP installation holes in locations previously marked Insert Plastic Screw Anchors N into RET holes 4 Reposition Wall Jambs C as before and secure Jambs to walls using the six 6 1 1 4 Installation Screws provided 3 per jamb 5 Before proceeding determine which side you want your door to strike left or right your choice Now measure the opening width between the two Wall Jambs C as shown in figure 3 and trim the strike side end of Sill Guide Track B to measurement obtained EASURE WIDTH OPENING always trim the strike side end never the hinge side end With Guide Track s high figure 3 lip toward exterior snap Track B into place as shown See also exploded view sheet 2 3 PARAGON BI FOLD 08 29 00 PATENTS PENDING 6 Strike side was determined in step 5 insert Strike Post D into the appropriate Wall Jamb C magnet should be facing toward exterior of enclosure see exploded view sheet 2 7 Before proceeding with Door Assembly installation note that the Door Assembly E must always fold in toward interior of shower enclosure see explode view sheet 2 Position Door Assembly on floor the way it will be installed on enclosure remember unit must fold into enclosure Install Pivot Bushing J Pivot Bushing Screw K and Slide Piece Set Screw L onto appropriate Slide Piece e6 as shown in figure 4 8 Install Magnet Holder A2. B38PHPT ADJUSTMENT SCREW e10 C940B Glazing Vinyl not shown e11 98 42 Magnetic Strip not shown e12 6 8114FHP Door Panel Assembly Screws 8 F DRIP RAIL ASSEMBLY R 634 DOOR STOP SCREW f 2340 Drip Rail f2 C176G Vinyl Door Sweep f3 4403 Drip rail Tape installed 2 D G CP930 DOOR HANDLE set 1 H 6114MSFHP DOOR HANDLE SCREWS 2 K _81MSFHP BUSHING SCREW MAGNET HOLDER ASSEMBLY i 942 Magnet Holder 1 D i2 98 44 Magnet 1 HISSTUIMSEHP BEOR HANDLE SCREW J SP189B BUSHING 3 4 x 3 8 O D 1 K 81MSFHP BUSHING SCREW 1 L 83212SS SET SCREW 2 gt M 6 8114PHP INSTALLATION SCREWS 6 N 1329 PLASTIC SCREW ANCHORS 6 M 6 8114PHP UNIT INSTALLATION SCREW O 638PHPT ADJUSTMENT SCREWS 12 P CP935 STRIKE PLATE 1 Q SP116B DOOR STOP 1 2 x 5 16 O D 1 R 634 DOOR STOP SCREW 6 x 3 4 1 INSTALLATION INSTRUCTIONS 1 Measure the base opening along center of shower curb as e shown in figure 1 Trim Sill A to 1 16 less than measurement obtained 2 With weep holes toward interior of enclosure position Sill at center of shower curb Temporarily tape Sill to shower curb to prevent movement MEASURE BASE OPENING figure 1 figure 2 3 Place Wall Jambs C into ends of Sill A and up against shower walls as shown in figure 2 Plumb the Jambs then pencil mark their installation holes locations on the shower walls 3 per jamb Remove Wall Jambs
3. Coastal Industries Inc FAX NO mm TELEPHONE NO 904 641 1697 P O BOX 16091 904 642 3970 JACKSONVILLE FLORIDA 32246 Paragon Bi Fold Door 1 PARAGON BI FOLD 08 29 00 PATENTS PENDING Paragon Bi Fold Door right strike configuration shown D i USE THIS SLIDE PIECE p ned spg DOOR WHEN UNIT STRIKES p RIKE O FET SEE OTE fi POORE Site ONLEFT SEE STEP Op Ibe o CR js IA rr 5 1 3 E WoT A fy i t 9 esq T Exploded View Outside of Unit Looking In 2 PARAGON BI FOLD 08 29 00 PATENTS PENDING PARTS KEY PART LETTER NUMBER DESCRIPTION QTY A 900 SILL 1 B 941 GUIDE TRACK SILL 1 KA C 903 WALL JAMB 2 d D 926 STRIKE POST 1 Q DOOR STOP E DOOR ASSEMBLY e1 920 Hinge Post 1 O e2 922 Hinge Stile 3 e3 924 Strike stile 1 e4 925 Rail 4 J _BUSHING e5 940 Center Hinge Pull 1 e6 37 Slide Piece 2 e7 CP932 Hinge Pins not shown 6 kme e8 CP148TW Hinge Washer not shown 6 e9 C921B Hinge Sleeve not shown 3 0
4. TERIOR OF SHOWER figure 5 Snap Magnet Holder Assembly into bottom rail as shown see also exploded view sheet 2 DRIP RAILS FLUSH WITH EDGES OF e AT POINTS NDICATED figure 6 figure shows from inside of unit looking out DOOR FLUSH WITH BOTTOM OF DOOR RAIL s TYPICAL 2 PLACES figure 7
5. re Hinge Post e1 and Strike Post D to the Wall Jambs using six 6 638PHPT Installation Screws O see exploded view sheet 2 13 Attach and center the Strike Plate face to the Magnet Holder Assembly and shown in figure 8a Step inside the shower enclosure close the door and mark the Strike Plate hole locations on the Sill Open the Door drill the hole locations and secure the Strike Plate to the Sill with two 2 638phpt Screws O as shown exploded view sheet 2 and figure 8 below 14 The purpose of Door Stop Q is to prevent the Door Panels from hitting upon themselves Using the pre drilled pilot hole in the Guide Track s bottom secure Door Stop Q to the Guide Track with one 1 Door Stop Screw R as shown in figure 9 15 Run a bead of clear mildew resistant caulking down the full length of each Wall Jamb outside where the Jambs meet the Walls Now run a bead outside where the Sill meets the curb Follow caulking manufacturer s instructions before using shower normally 24 hours Installation is now complete Center the Strike Plate on the Magnet Assembly figure 8a INSIDE OF ENCLOSURE L Locate MARK AND SECURE STRIKE PLT figure 9 figure 8 4 PARAGON_BI FOLD_08 29 00 PATENTS PENDING DOOR STRIKE DOOR ASSEMBLY H ALWAYS FOLDS f D IN i figure 4 figure shows parts installed for a right hand strike Door BOTTOM DOOR RAILS MACNET D EX
6. ssembly 1 onto the bottom rail e4 of the hinge side door as shown in exploded view sheet 2 Note that Magnet Holder Assembly is installed as close to Center Hinge Pull e5 as possible Magnet i2 must face toward the outside of the shower enclosure as shown in figure 5 9 Clean bottom rails of Door Assembly with alcohol to remove any oil Failure to clean door rails prior to installation of Drip Rails F may cause tape to release Remove backing from tape and position Drip Rails flush with edges of Hinge Stiles e2 as shown in figure 6 and flush with bottom of Door as shown in figure 7 Secure Drip Rails to Door Panels using four 638phpt Screws O as shown in exploded view sheet 2 and figure 5 10 Insert the Door Assembly s Hinge Post e1 into the Post from which it is to swing Bring the Hinge Post to rest atop the Guide Track B and insert the Pivot Bushing J into the Guide Track cavity Remember that regardless of whether the door strikes on the left side or the on the right side the Door Assembly must always fold in toward interior of shower enclosure Temporarily leave as is 11 Attach the Door Handles G to the door using two 2 Door Handle Screws H as shown in exploded view sheet 2 12 Step inside the shower enclosure and close the Door Check to make sure that bottom of Door Assembly E is parallel to the Sill A If it is not make it so When satisfied that the Door Assembly is parallel to the Sill secu
Download Pdf Manuals
Related Search